Search Documents

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

Introduction The Homestake Mining Co. has always been big on gold. After 108 years in the business, the company and its principal product are almost synonymous. The relationship continues. On Sept. 28, 1985, Homestake held formal dedication ceremonies for its newest gold mine - McLaughlin. The McLaughlin open-pit operation is located in northern California, some 113 km (70 miles) northeast of San Francisco. It lies near the boundaries of three counties - Napa, Yolo, and Lake - and a portion of its facilities are located in each. McLaughlin was originally the site of the Manhattan mercury mine that produced nearly 80,000 flasks of the quicksilver from the 1860s to 1978. At the September dedication, Homestake renamed the mine in honor of the late Donald H. McLaughlin. McLaughlin was with Homestake for nearly 60 years. He rose from exploration geologist to his ultimate positions of chief executive officer, director, chairman of the board of directors, chairman emeritus, and chairman of the executive committee. The discovery of the McLaughlin deposit occurred in 1978, the last year of operation for the Manhattan mine. Homestake geologists used a newly developed model and found surface gold at the mine site. That same year, Homestake signed an agreement with the property owner and began a two-and-a-half year exploration program. An initial discovery announcement of 31.1 t (1 million oz) of gold was made in 1980. In 1981, this was revised to 93.3 t (3 million oz), or 18 Mt (20 million st) of ore grading 5.2 g/t (0.152 oz per st). Expected mine life is 20 years. Construction began in September 1983, following the issuance of stage one permits. Start-up of operations took place in early 1985 and the first gold-silver dore bar was poured on March 4. Since then, more than 540 kt (600,000 st) of ore has been milled, producing about 1.6 t (50,000 oz) of gold. Of special interest at McLaughlin is the use of three autoclaves for gold extraction. According to Homestake, this is a first. The autoclaves are designed for a 90% gold recovery rate. Early results have proven yields at this rate and higher. Geology The McLaughlin deposit is about 1.5 km (5000 ft) long. It occurs as a wedge-shape, narrowing to a verti-

Jan 1, 1986

On Nov 1, 2007 House Resolution 2262 ? The Hardrock Mining and Reclamation Act of 2007 ? was passed by the U.S. House by a vote of 244-166. HR-2262, among other things, would impose a 4-per-cent royalty on existing mines with commercial production and an 8-percent gross royalty on all new claims. Not surprisingly, this possible new law was one of the hottest topics of discussion at the Northwest Mining Association?s conference that this year returned to Spokane, WA for its 113th annual meeting on Dec. 3-7. More than 1,800 delegates attended the conference that was held under the banner theme of ?Mining ?. For today and tomorrow.? Northwest Mining Association executive director Laura Skaer was one of many speakers during the three-day conference to respond to the threat to the industry posed by HR-2262 with a presentation titled ?Potential changes to the 1872 Mining Law.? In the presentation that she first unveiled at the Alaska Miners Association?s convention and trade show on Nov. 8, Skaer laid out a comprehensive list of problems with HR-2262. In addition to the association?s obvious concerns about the proposed royalty, Skaer noted that the bill includes a mine veto provision that would allow the Secretary of the Interior the authority to deny an operations permit to a project if the secretary determines that the operation would cause undue degradation to public lands and resources. Potential massive withdrawals from mineral entry are also included in HR-2262. Among the lands that could be off limits to miners under HR-2262 are wilderness study areas, areas of environmental concern and 23.6 hm2 (58.5 million acres) identified as Roadless Rule. States, political subdivisions and Indian Tribes would also have more authority to withdraw lands, she said. To combat the proposed changes, Skaer made 10 trips to Washington D.C. on behalf of NWMA members in 2007. In her presentation at the annual meeting, she also objected to provisions that include no life-of-mine permits and uncertain permit renewals and new and duplicative environmental standards that she said are vague, ambiguous and inconsistent with current federal and state environmental laws. Debra W. Struhsacker, an environmental permitting and government relations consultant, also spoke on the issue of HR-2262 with a presentation titled ?The House mining law bill ? Rip van Winkle is back ? and he?s meaner than ever.?

Jan 1, 2008

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By H. Do, R. Yoon

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 to 100 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2007

By Katzer R. Klimpel, J. Sewell

Dr. Roussey Roussev The use of chemical additives on grinding is of significant importance considering the high energy consumption of grinding processes. My research indicates that the dispersant approach explains the effects, in this particular case of wet grinding. Further, the dispersant approach combined with torque measurements give the possibility of clarifying the mechanisms involved when using grinding aids. I find the conclusions derived from the data obtained to be correct and useful for grinding. In general, I agree with the explanations. However, I would like to discuss several additional points that I consider to be important, and in the same time to mention some of my own results from investigations similar to those presented in the study under discussion. The "bed volume concept" and the change of slurry viscosity explain adequately the data plotted on fig. 3, in conjunction with Figs. 1 and 2. However, the significant increase of the average torque in the case of 83% solid with XFS-4272 introduces the necessity of establishing the optimum of percent solid when dispersant is used. For example, the optimum percent of solid for different materials varies. One of the reasons is the material's mass density. On the other hand, it is necessary to determine the concentration of the chemical used. Because of this, it would be interesting to know how the cited concentration was selected. The supportive discussion and verification by Dr. Roussev, with results similar to that of the paper, is appreciated. I will try to answer the additional questions he has raised. To begin with, the mill was fitted with six lifters of approximately one-quarter inch height. There has been extensive lab and plant level work to understand downstream influences of using dispersants like XFS-4272*. In sulfide ore processing, which is the area in which most industrial scale testing has been performed with this approach, neutral to positive influences have been observed. For example, positive effects (e.g., increased recovery) have been noticed in flotation operations involving ores that have a tendency to produce excessive slimes upon grinding. (1) Also, the use of a dispersant has been shown to demonstrate a positive influence on classification by improving the sharpness of separation and preventing a decrease in d50 value that usually accompanies increasing flow rates to classifiers.(2) The biggest potential downstream problem is in thickening, which at the dosages involved, has not been a problem in plant scale usage. The commercial price of dispersants like XFS-4272 is quite variable depending on source, concentration, etc, but a typical cost of XFS-4272 to achieve a 10% increase in throughput in industrial mills has been between 20 and 35- US per ton of feed ore (1981).

Jan 12, 1982

By Michael V. Mergentime, Prakash M. Donde

The Nutley Quarry Trunk Sewer Project is a good example of a tunnel that went through difficult and complex ground. The 2 m (7ft.) diameter and 840 m (2,750 ft.)long tunnel passed through soft ground, mixed face, and hard sandstone. The soft ground and mixed face tunneling provided several challenges. During excavation of the tunnel, the Contractor encountered a number of unanticipated large boulders. In addition, the length of the mixed face portion of the tunnel increased by 100%. The Contractor tried various construction techniques to overcome the difficult ground conditions and complete the project. The tunneling progress was slower than expected. The Contractor claimed extra costs for differing site conditions. Through discussions and negotiations between the Contractor, Engineer, and Owner, all of the changed condition claims were settled before the construction of the project was completed. This paper addresses the difficult ground conditions, claims evaluation, and how they were resolved by cooperative efforts between the Contractor and the Owner/Engineer.

Jan 1, 2001

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By Morteza Gharouni Nik

Flexible Dilatometer Test (FDT) is one of the in-situ test methods for determining the deformational characteristics of rock masses. In this study, several dilatometer tests have been conducted in different geotechnical phases of site investigations by means of two types of FDTs. The purpose of this paper is comparison of the performance of these two types of dilatometers and analysis of the differences in the results of the tests.

Jan 1, 2008

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By T. Tafi

The Ute-Ulay project area is located approximately five miles west of Lake City, in Hinsdale County, Colorado. The Ute-Ulay Mine site is approximately one mile east of the project area. The elevation of the site is 9,200 feet and is adjacent to Henson Creek (Figure 1) [ ] The Ute-Ulay Mining complex is an inactive gold, silver, and zinc mining/milling operation, that operated from the 1880?s until the 1970?s, and sporadically into the late 1990?s. The mining complex comprises several levels of underground mines, a flotation mill, and an abandoned town site. Due to the narrow, steep sided canyon, milled tailings were pumped upstream one mile in a sluice box to a wider section of the canyon, and deposited into five tailings impoundments and one berm located between the impoundments. An estimated 9,000 cubic yards (yd3) of fine grained tailings were located in the impoundments adjacent to the creek. The Ute-Ulay project area consisted of the mill tailings impoundments located upstream from the historic mine.

Jan 1, 2011

MINExpo International is billed as the largest exposition for the mining and mineral processing industry. And the 2012 edition, scheduled for Sept. 24-26 in Las Vegas, NV, is no exception. Put on by the National Mining Association (NMA), attendance at this year?s show is expected to be significantly more than the 38,500 who attended the last MINExpo in 2008. The exhibit will also be quite a bit larger in 2012 than it was at the previous MINExpo. More than 1,800 companies, representing more than 30 countries, will fill the Las Vegas Convention Center. The more than 850,000 sq ft of exhibit space will include the North and Central halls as well as South Halls Nos. 3 and 4. And the Silver Lot outside of the front door, under construction in 2008, will be filled with more exhibitors. The 2008 show attracted about 1,220 exhibitors occupying more than 600,000 sq ft of exhibit space.

Jan 1, 2012

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM)/Hatch Mott MacDonald (HMM) joint venture has been engaged by the New York City Economic Development Corporation (NYCEDC) to provide engineering ser-vices in connection with the replacement of two existing siphons which cross New York Harbor between Staten Island and Brooklyn. The project involves the construction of a 72-inch diameter pipeline within a 12-foot diameter tunnel beneath the New York Harbor. The tunnel will be constructed using either slurry or an earth pressure balanced (EPB) tunnel boring machine (TBM). This paper presents the results of an extensive geotechnical field and laboratory testing program including advanced frozen soil tests (uniaxial compressive strength tests, triaxial tests, and uniaxial creep tests), in-situ vane shear and pressure meter testing, and a marine geophysical survey (seismic reflection technique) to ascertain the complex subsurface conditions along the tunnel alignment and shaft locations. The paper will also discuss the design and construction aspects and the challenges associated with each component of this project.

Jan 1, 2008

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Lucy McCartan, US Geological Survey, was the chair of the SME industrial minerals technical committees. She also served as the vice chair for agricultural minerals. Other technical committee vice chairs were: •Gary Tomaino, Specialty Minerals Inc., ceramics and refractory materials. •Srinivas (Vas) Veeramasuneni, US Gypsum, chemical raw materials. •William Langer, US Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2002