Search Documents

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By R. Hummel

When the slope angles of the southern side of the Venetia open pit were required to be flattened by some 20 degrees after an analysis completed by De Beers geotechnical engineering in conjunction with SRK, the additional waste stripping tonnage generated was in the order of some 70 million tons. The potential cost of having to move this tonnage had a significantly negative effect on the Net Present Value of Venetia Mine, challenging the viability of the third pushback and rendering a potential fourth pushback completely uneconomic. This paper details some of the innovation that went into the design and planning process undertaken to virtually negate the instantaneous effect of the flattened slope angles and the associated waste tonnage as well as further improve the NPV of Venetia Mine and bring the fourth pushback back into economic viability. This process has become known as NPV+ and is anon going exercise in waste reduction/deferment and revenue advancement.

Jan 1, 2001

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By S. H. Yi, J. R. Kim, Y. S. Lee

The viscosities of CaO-SiO2-Al2O3-MgO-FeO slags were measured under conditions ofCaO/SiO2=1.15–1.6, 10–13 percent Al2O3, 5–10 percent MgO and 5–20 percent FeO. Slag viscosity decreased with increasing FeO content at a fixed basicity (CaO/SiO2) of slag. Slag viscosity at low FeO (<7.5 percent FeO) exhibited a minimum value by increasing MgO content in slag. Viscosity decreased with increasing slag basicity up to 1.3 while it increased as slag basicity increased from 1.3 to 1.5. Thus, it was proposed that the driving force for the decreases of slag viscosity would be an increase in depolymerization of silicate network at C/S=1.3, while the viscous behaviour at C/S>1.3 would be increased with increasing the chemical potential of primary solid phase e.g. dicalcium silicate. A thermodynamic approach for the activity of primary solid phase in molten slags resulted in a reasonable relationship between viscosity and slag components. Therefore, it was confirmed that slag viscosity in basic slags system (C/S>1.3) could be determined by the chemical potential of dicalcium silicate. Keywords: viscosity, basicity, bosh slag, blast furnace, slag structure, FT-IR

Jan 1, 2004

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By A. J. Basu

New technologies, such as computer based learning, wireless computing, internet2, online courses, distance learning, and in general multimedia applications are being implemented in the higher education sector in an increasing manner. However, these implementations are not coherent, and lack standards. However, one example of the existing standards is the development and implementation of the virtual learning environments. These technology tools help in delivering the eLearning objectives. There is a major initiative in Europe (eEurope action plan) in promoting eLearning towards creating a knowledge-based society. Technology implementation is the major driver for achieving the eLearning objectives. A two-year pilot project on implementing technology tools including virtual learning environment (VLE), video-conferencing, and simulation and visualization was carried out for providing a blended learning environment for undergraduate and graduate students in Mining Engineering (undergraduate) and Mineral Deposit Evaluation (M.Sc.) course at the Imperial College London. The pilot project was funded by the Imperial College Centre for Educational Development (ICCED). The project did contribute towards activities for creating an institute-wide eLearning strategy in line with the eEurope action plan.

Jan 1, 2003

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By R. D. Hull

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Mining) degree As a partial fulfilment for the degree of B.Sc. (Eng) (mining) at the University of the Witwatersrand, a dissertation was to be completed in the mining industry. This was done at Finsch mine, with the purpose of determining the best solution to the required secondary breaking problem. In order to complete the study of the secondary blasting method available for use in the new block 4, cave mining method at Finsch mine the following problem statement was identified and solved ?The methods currently in use, for the secondary breaking of oversize rocks at their source in the current production levels, are to be investigated, and their applicability to the new block 4mining project determined?. To effectively achieve this problem statement above; time was spent researching and investigating, in depth, the methods that are currently in use at both Finsch and Koffiefontein mines; so as to gain practical knowledge of these. The methods were identified and independently evaluated, taking into consideration factors such as costs of the equipment, time to break oversize rocks, advantages, disadvantages, safety and labour requirements, etc. This in turn then allowed for a direct comparison between the methods and the decision as to the best to apply to the new block 4 production level. The methods that were investigated included: ?Concussion blasting, where concussion bombs and lay-on charges are used to break hang-ups and boulders. ?Drill and blast methods, where holes are drilled in large rocks and charged manually with explosives. ?Emulsion secondary blasting, which is a new project in use at Koffiefontein mine from African Explosives Limited. ?The Ro-BustTM breaking system, a hydro-fracturing breaking system. Once all the methods had been evaluated and compared it was found that the Ro-BustTM Breaking system was the most applicable for the breaking of boulders, with, the Emulsion Blasting System being used for hang-ups. Further information and the more in-depth version of this report, is stored in the resource centre at De Beers?Finsch Mineand the School of Mining Engineering WITS University.`

Jan 1, 2002

By W. S. Steinberg

Keywords: Pyrometallurgy, furnace, open slag bath, Evraz, Highveld In 1963, the full-scale engineering study for the development of an Iron, Steel, and Vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steel works that produced steel and vanadium-bearing slag by using a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for pre-reduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to Open Slag Bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of a higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By L. Jurca, C. Gligor

After 1990, a great process of re-organisation and economic reform has occurred in the Romanian mining sector and especially in the pitcoal mining in the Jiu Valley. This process has included both legislation and the main aspects for getting an economic efficiency in the environment issues and for dealing the problems with social impact. Accordingly, starting with the year 1993 a new mining method has been introduced to turn efficient the pitcoal mining, and we speak about mining with caved in bed. This method has two variants: - with transverse strips and caved in bed; - with long face and caved in bed. Each of the above-mentioned variants has in turn several subdivisions, depending on how the longwall is prepared and on other characteristics. By using this method, the output has increased compared to other mining methods. The main safety aspects concerning caved in mining refer to: - great emissions of methane; - technical aspects (a mining method system, supports, discharging process); - pressure driving (analysed for the case of mining with long face, with transverse strips as well for the case of transverse strips when mining a subsequent sublevel).

Jan 1, 2003

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By A. Whillier

The decisive action taken by mine managements in recent years has been the main factor in bringing about the present downward trend in mine fires. A better understanding of the fundamental factors that govern the ignition and spread of fires. obtained as a result of investigations into mine fires, has provided useful guidance to production personnel. Similar investigations into fire-fighting techniques have assisted the Rescue Training Service and mines to institute more effective fire-fighting techniques. Some of the more important findings of recent investigations in these areas are outlined.

Jan 1, 1981

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

A low noise blast hole drilling system was developed to limit the risk of noise induced hearing impairment in mining operations. Noise induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise induced hearing. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard Seco S215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock shavings, oil and grease) is removed from the encapsulating tubes via exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2003

By P. L. Duncanson, J. D. Toth

Since 1995, when "freeze lining" refractory systems were introduced to the ferroalloy industry, they have gained in popularity, due to the freeze lining?s reputation for reliability, safety, and the contribution it makes to profitability. As with many popular and effective technologies, however, the freeze lining has spawned low-cost pretenders that claim the "freeze lining" name. On the surface they appear to contain some of the components of the technology, such as thermally conductive materials, but they fail to incorporate all of the principles that define a true Freeze Lining. The term "freeze lining" refers to the refractory system?s ability to maintain a temperature profile that is low enough to freeze a layer of process material on its hot face, which insulates the refractory and prevents direct contact with molten metal and slag. In doing so, the common wear mechanisms found in the submerged arc furnace - chemical attack, erosion, and thermal stress - can be prevented. These wear mechanisms are all related to high temperature; thus, they are prevented by maintaining low temperatures. Certain refractory properties and design concepts are absolutely necessary for the lining system to function as a true Freeze Lining. The paper explains these requirements and why they are important - the Truth of freeze linings - and further explains why systems that ignore one or more of these requirements cannot claim to be freeze linings, thereby exposing the Myths.

Jan 1, 2004