Search Documents

By J. A. Maree

After the South Deep complex was purchased by Goldfields in 2006a re-feasibility study was done and the life of mine (LOM) was extended to 52 years. This also implied that the mine?s infrastructure would have to be enhanced. One of the changes was the proposal of five new main orepass systems to be excavated before the mine reaches full production in 2013. Excavations started to show signs of scaling, and in some cases, whole new excavations were lost. This particular area was exposed to very high stresses and the geology was prone to body delimination rendering the relevant areas unstable. This paper investigates the conditions at the location of one of the proposed orepass systems, and the best possible orientation was suggested to ensure that the orepass system would be stable and have a practical life. It was, however, found that the fourth leg of the orepass system would require further support to be classified as stable by the chief rock engineer and the section geologist of South Deep. Several support methods and orepass system linings would then be analysed and evaluated to give calculated recommendations on how to productively and practically support an orepass system. Keywords Main orepass system, stresses, body delamination, impact and abrasion, rock support, concrete lining.

Jan 1, 2011

Book review Doyle, William S. Strip Mining of Coal; Environmental solutions. Park Ridge (New Jersey), 1976. 352 pp. $32. Surface mining of coal is still in its infancy in South Africa. The environmental repercussions following large-scale disturbance of the land surface, and the secondary effects of the disposal of waste products and effluents from mining, have not yet become apparent.

Jan 1, 1977

By R. C. More O’Ferrall

The author mentions some of the problems he has encountered, together with their solutions. These include the stoping of isolated pillars, the reduction of the size of shaft pillars, the stoping of a new horizon above or below a horizon that has already been stoped out, and the mining of thick bands of reef left behind in the footwall or hanging wall.

Jan 1, 1981

By R. C. Dunne, W. A. Gilbert, I. J. Corrans, K. S. Liddell

After bench-scale and pilot-plant tests in which it was shown that wet high-intensity magnetic separation (WHIMS) can achieve good recoveries of gold and uranium from Witwatersrand residues, a production size machine was installed at a gold mine. The mechanical and metallurgical performance of this machine have been satisfactory, and the economics of the process are attractive. WHIMS can be combined with other unit operations like flotation for the optimization of overall gold and uranium recoveries. This concept is shown to be relevant, not only to operations for the retreatment of tailings, but to processes for the treatment of coarser material. In the latter, there is a saving in energy consumption compared with the energy required for the fine grinding of the total feed, and a material suitable for underground backfill can be produced. Improved. more cost-effective WHIMS machines currently under development are also described.

Jan 1, 1983

For practical reasons all basic input data for the gold mines of the Anglovaal Group conform to a regular grid of averages of sample values within 25-ft squares in the plane of the ore body; individual sample values with their metric co-ordinates are input and converted by a computer program to the basic 25-ft square averages. At the Prieska copper mine the bore- hole data are forced on to a regular grid of 15-m squares corresponding to the coordinates of the grid points nearest to the actual borehole intersections. As for the gold mines the Prieska ore body, although some 3 to 30 m thick, is also dealt with on a two-dimensional basis (Krige, 1973). On the gold mines the data subjected to geostatistical analysis cover: gold values (in cm g/t), uranium values (cm kg/t), and channel widths (cm). The gold and uranium values are normalised on the basis of log (value plus constant) and all the geostatistical analyses are performed on these transformed values. The channel widths usually conform reasonably well to the normal distribution and are, therefore, not transformed. At Prieska the metal grades analysed cover the two main products, copper and zinc, as well as the impurities lead and bismuth; in addition the specific gravity values and the hanging- and foot-wall deviations from a projection plane are also handled. These were all previously used on an untransformed basis but because of problems associated with the proportional effect the lognormal-de Wijsian model is now used for some of the grade variables. The key computer pro- grams can be summarised briefly as follows:

Jan 1, 1981

By D. Limpitlaw, A. Alsum, D. Neale

"Ecological footprint analysis (EFA) was first described in 1996 as a measure of carrying capacity appropriated by human activities. EFA is a resource and emissions accounting tool designed to track the demand on the biosphere’s regenerative capacity. Ecological footprints are increasingly used as indicators of organizational and corporate environmental performance and product sustainability. There is a compelling argument to develop an EFA tool for mining companies.To determine the size of a mine’s ecological footprint, land requirements for all categories of consumption and waste discharge must be summed. This land is only made up of the ecologically productive land and water in various classes (cropland, pasture, forests etc.) required on an ongoing basis to provide all energy and material resources consumed and absorb wastes.A challenge in conducting an EFA for a mine is the shortage of accessible data. Undertaking an EFA for a corporation or individual site entails compiling consumption and emissions data (which can be used for other reporting applications). The footprint results themselves highlight the most critical aspects of an organization’s impact on the environment and provide a platform for focusing actions and for educating the workforce to improve their contribution to best-practice operations. This paper discusses the benefits and challenges of undertaking an EFA for a mining company, and provides examples of the various components of ecological footprints associated with mines, as well as showing how an EFA can be used to understand and communicate some of the impacts associated with mining activities.IntroductionFundamental biophysical and economic limits are now being experienced in many countries around the world. Herman Daly, a former World Bank economist, described this scenario as ‘uneconomic growth’, where the costs of growth exceed the benefits (Daly, 2005). This occurs when the economy’s expansion encroaches excessively on the surrounding ecosystem, sacrificing natural capital. Under such conditions the sacrificed natural capital is more valuable that the resulting economic growth. Consequently, the world faces largescale threats to sustainability and especially to the viability and continued existence of the ecosystems that support human settlements (El Zein et al., 2014). In recognition of this sustainability imperative, mining companies are increasingly concerned with their ecological footprint (EF)."

Jan 1, 2017

By R. du Preez

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when attempts are made to maximize the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory testwork was conducted on the raffinate of the cobalt solvent extraction circuit to optimize the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimized in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory testwork results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

By L. C. Woollacott

A computer-aid is described that is designed to calculate steady-state material balances for ore-dressing circuits. The program determines the material balance from a specification of the process condition. No mathematical models or data adjustment techniques are employed. As such the program complements existing simulation and material balance 'smoothing' packages. The process condition is specified using performance indicators. These are significant parameters in the industry with which all practising mineral processors are very familiar. The program employs an equation-oriented technique for material balancing and so has had to deal with the difficulties peculiar to that approach.

Jan 1, 1987

Palabora Mining Company is operating a copper block cave mine in the Limpopo Province of South Africa. The mine was developed in the late nineties with a target ore reserve of 220 million tonnes of carbonatite at 0.69% copper. At 30,000 tonnes per day the operation had an estimated life of mine of approximately 23 years. Cave induced open pit side wall failure occurred in late 2004 with 130 million tonnes of waste reporting to the bottom of the open pit. This failure resulted in potential sterilization and dilution of the ore reserve and subsequent reduction in life of mine. Physical and numerical modelling indicated potential losses of up to 30% of the original ore reserves. Cave Management tools based on throughput principles are utilized to manage the failed waste ingress and ensure an optimum life of mine. Extracting the maximum rate possible, as soon as draw points are commissioned, with the view of achieving the highest production in the short term, is any mining operation?s goal as more money is required sooner. This approach, of course, improves the cash flow but presents a risk in the cave propagation profile as overall draw control is compromised. At Palabora it is evident from a Mineral Resource Throughput Management (MRTM) point of view that maximum production in the short term is not the solution. If high production rates are achieved and the profile of the cave is not manage correctly, this results in failed waste reporting to draw points earlier with adverse effects on grade. This would effectively and significantly shorten Palabora?s Life of Mine. The applications of good MRTM principles are required to assist the value chain for sustained profitability. The process commenced with change management paving the way for a better understanding and a holistic view for all role players.

Jan 1, 2007

By C. J. Alberts

The perception exists in many organizations that, once an energy management system is employed, there need not be any further adjustments to such a system. This is not true, as the field of energy management is a dynamic field, and constant feedback and adjustments are needed to enhance the efficiency of a system to the point that substantial pay-back can be obtained. It is stressed that for any energy management system to be successful, careful planning should permeate through the organization, from the top level decision-makers to the workplace. This paper describes a dynamic technique by which energy management strategies can be evaluated by viewing the effects of the strategies on the organization as a whole.

Jan 1, 1997

By R. S. J. Du Toit

SYNOPSIS This paper is based on a thesis dealing with the problem of basing the current rate at which money is collected from mine owners to pay compensation for pneumoconiosis in the future, on the current dust hazard on mines. The certification of pneumoconiotics and the incidence of pneumoconiosis are discussed against the background of existing legal provision for collecting funds for compensation. The various pneumoconiosis indices are considered. In the data analyzed, the only pneumoconiosis index common to a number of classes of mines is the time it takes to develop pneumoconiosis. Sets of dust indices and pneumoconiosis indices are computed. Expressions are derived for the time it takes to develop pneumoconiosis as a function of the dust hazard, and for the collection of funds as a function of the time available for collection. From these two expressions follows an expression for the rate of collecting funds as a function of the dust hazard.

By P. J. A. Beukes, C. C. La Grange

INTRODUCTION Some years ago the authors proposed a modified procedure1 for carrying out micum index determinations2. The modifications consisted of using a drum of 50 cm internal length, i.e. half the length of the standard micum drum (a modification also adopted by the B.S.J.3), and the use of a + 25 mm coke instead of + 60 mm coke for the test. The proposed modified test and formulae for converting results obtained from it to standard micum test results and vice versa were based on the results obtained during the investigation of about 200 test cokes made in ovens of the South African Steel Industrial Corporation Limited (Iscor), the Fuel Research Institute co-operating with the experiments. Extensive testing of cokes has since been done at the Fuel Research Institute using both the standard and the modified procedures. The numerous test results obtained during this trial period fully support and strengthen the confidence originally expressed by the authors in the modified testing procedure. The scope of the modified micum index determination has in the meantime been extended by applying the testing procedure also to test cokes made in the Institute's experimental coke ovens, and also in this case the modified procedure has proved its usefulness. A difficulty is that when comparing the characteristics of cokes made in the Institute's two experimental coke ovens with each other and with those of cokes made from similar blends in commercial coke ovens, for example those of Iscor, the index values obtained invariably do not check exactly due mainly to inherent differences between the different types of oven4. For instance, resistance to abrasion of a coke made in Iscor's ovens is always appreciably higher than that of a coke made from the same blend (and having a similar moisture content) in the experimental ovens. This makes direct comparisons and the prediction of quality to be expected from commercial products, based on experimental coke oven results, difficult. It may also be added that workers in Great Britain some years ago reported a similar experience5. In the authors' opinion the main reason for the discrepancy is the relatively low height of the experimental ovens resulting in a much lower static pressure on the charge during coking than that obtaining in a commercial oven. The difficulty was pointed out and briefly discussed in a publication4 which appeared at a time when the micum test for coke evaluation had only just been introduced at the Institute, so that only B.S. shatter and abrasion test results were available for discussion in the publication. Needless to say, the introduction of the micum test by no means solved nor even alleviated the problem. On numerous occasions during the past few years the Institute has had to conduct contract investigations in its experimental coke ovens on behalf of companies which invariably desired an indication of the quality of coke likely to be obtained from certain coals or blends when coked commercially, more particularly in Iscor's type of coke ovens. It was, therefore, essential to accumulate statistical data which would enabe the prediction to be readily made. Fortunately the compilation of comparative coke-quality index values for the three types of oven under consideration has become possible as a result of coking investigations conducted in co-operation with Iscor over a number of years. During this period Iscor, on numerous occasions, kindly made available to the Institute portions of coals and blends coked in the Corporation's coke ovens, thus enabling parallel coking tests to be carried out in the Institute's experimental ovens. In this way enough statistical data became available to establish relationships between coking results obtained in Iscor's ovens and results obtained on similar coal charges in the Institute's ovens. The most practical and acceptable method of overcoming the problems of finding a suitable and simple basis enabling direct comparison between the cokes of the different origins mentioned to be made, is the assignment of descriptive arbitrary quality ratings, as indicated below, to the cokes obtained, it being argued that the quality rating assigned to coke made from a given coal or blend in the different coke ovens under standardized conditions should be the same, irrespective of differences in the index values obtained when subjecting the cokes to the usual coke evaluation tests. The system, which should enable the sponsors of coking investigations in the Institute's experimental ovens to make their own interpretations of the results obtained, is explained below. ARBITRARY QUALITY CLASSIFICATION OF COKES The Ml0m index1 (percentage material smaller than 10 mm after the test) of a blast furnace coke is a measure of its tendency towards breeze formation during handling -a low value indicating a low tendency. This is generally of greater importance under ruling South African conditions, than the M'40 index1 (percentage material larger than 40 mm after the test), which can be regarded as a measure of resistance to shatter. In fact, if the M10m value of a coke as made in Iscor's ovens is higher than about 11, the tendency of the coke to form breeze during handling and in the blast furnace is relatively so high that hardly any notice need be taken of its M'40 value, even if this is comparatively high. For this reason, therefore, much more weight should normally be assigned to Ml0m indices in the quality evaluation of cokes made from South African coking coals and blends, as the coals

By F. Smit

Mining and plant practices can benefit from preconcentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of preconcentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2013

By J. O. Marsden

The copper industry is cyclical with the price determined by market forces (i.e. the balance between supply and demand for the metal.) The period of each cycle typically varies between 6 to 9 years. These cycles drive decision making for exploration, new project and mine development, mine closures, process improvement, research and development, and technological innovation. The gold industry is fundamentally different from copper in that supply and demand do not, alone, determine metal price and many other factors play a key role, including global and regional financial conditions, political stability, and the global future economic outlook. However, the gold price experiences trends and longer term cycles that similarly drive business decision making. This paper examines developments in the copper industry that have occurred over the past few price cycles (approximately 20 years) and explores how the lessons learned can be applied to gold extraction. A number of specific examples and opportunities are discussed in detail, including; technology development and innovation, cost control and business improvement, material characterization, comminution equipment, biological heap leaching, and concentrate pressure leaching.

Jan 1, 2009

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By H. Edinger

China?s engagement with the African continent has increased impressively in the past decade. Even though China is not the African continent?s largest stakeholder, the rapidly increasing engagement is evident in the huge number of Chinese migrants that have come to Africa in the wake of unprecedented trade and investment levels, as well as in increasing diplomatic and political interactions, which has taken most other commercial partners by surprise. All but four countries in Africa have adopted the ?One China?1 policy stance; and in so doing opened the door for new or strengthened commercial dealings with China, including increasing investments into Africa?s extractive industries. This has been particularly evident since the turn of the century, with a clear shift in China?s policy towards Africa elevating the continent in China?s foreign policy objectives. As such, Africa has become a strategic focus2 for Chinese outward bound and internationalizing companies, especially in the extractive industries. This planned shift in focus is based largely on geo-strategic and commercial needs and interests, rather than previous ideological ones.3

Jan 1, 2011

By S. Shamaila

The design and efficient operation of density-based mineral processing units requires regular densimetric analysis to be carried out on the various associated process streams. The results obtained from such analyses can have wide application, including the generation of washability and partition curves, which are critical for process design, control, and simulation. This paper describes some of the collaborative efforts that Kumba Iron Ore, in partnership with Springer New Technology and Anglo Technical Solutions Research, is pursuing in developing a novel density determination technique exploiting X-ray transmission (XRT) and optical imaging. This technique is being developed with the aim to determine sample density distributions that apply to washability characterisation of ores. This technique is aimed to be an alternative to the traditional sink and float method. For certain applications sink and float has required the use of tetrabromoethane (TBE) solution?a chemical that has been classified as harmful and environmentally unfriendly. This paper therefore presents some achievements in developing this novel technique which seems to be very promising.

Jan 1, 2012

By F. T. Cawood

This article offers a personal and independent view on the threats to the sustainability of the South African minerals industry. It argues that if the six identified threats of insufficient spending on research and development, general standard of education, nationalization, inadequate infrastructure, Aids prevalence and labour inefficiency are not acted upon as a matter of urgency, the future of the mining industry, along with its important contribution to the economy, is at risk.

Jan 1, 2011

By J. A. L. Napier

By use of a functional model of capital expenditure developed earlier, a prototype cash-flow model is formulated as a basis for the investigation of the economic consequences when the production rate of a mine is manipulated as fundamental design variable. The optimum production capacities that maximize the common economic criteria of net present value, present-value ratio, and wealth growth rate are determined. It is shown that these choices depend certain key groupings of the economic parameters, and that they have a fixed interrelationship. The basic cash-flow model is extended further to include the effects of a constrained rate of production buildup and the imposition of State taxation on generated income. An approximation to the initial tax-free period of a new mining venture is developed, and, by use of these results, the optimum choice of production level is analysed when both the buildup rate is constrained and tax is imposed. This extended model permits a comparison between the performance of existing mines and the predicted theoretical production levels for these mines.

Jan 1, 1981

This paper describes an interactive personal computer program, ENVIRON, which simulates cooling and ventilating systems on gold mines. An example of the practical application of the program is given and proposed future developments are discussed. The program consists of two main modules, HEATFLOW and VENT- FLOW. HEATFLOW calculates the heat loads and the effect of air coolers, while VENTFLOW estimates the air flow distribution. As the calculation of the heat loads requires a knowledge of the air flow and vice versa, the two modules are run iteratively until the solution converges. The program is written in Pascal and runs on any IBM-compatible personal computer.

Jan 1, 1987