Search Documents

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The performance of the improved microclimate suit by N. B. STRYDOM M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, B.Sc. (Potch.) (Visitor), and W. H. VAN DERWALT, M.Sc. (Potch.) (Visitor) An assessment has been made of a new improved microclimate jacket when worn by men working for four hours in a hot environment (wet-bulb temperature of 33,9°C and an air speed of 0,4 m/s) and at work rates of 35 Wand 70W. At the lower rate of work in heat, the use of microclimate suits maintained the rectal temperatures of the men at almost the same level as when they worked without that protection at normal room temperature (20°C). At the greater rate of work without protection, the men's rectal temperatures rose to 40°C within two to three hours, so that they could not complete four hours of work. When they wore microclimate suits, they easily completed four hours of work, and their rectal temperatures were lower than when they worked at the lower rate without protection.

Jan 8, 1975

Book Reviews M. J. Jones(ed.). Geological, mining and metallurgical sampling London, The Institution of Mining and Metallurgy, 1974. 268 pp. £8. Spooner, J., et al. (eds.). 1974 miningannual review, London, The Mining Journal Limited, June 1974. 506 pp. £14,25 (including annual subscription to Mining Journal and Mining Magazine). J. H. Quilliam et al. (eds.). The ventilation of South African ~old mines. Johannesburg, Mine Ventilation Society of South Africa, 1974. 488 pp. RI0,00. The Hans Merensky Foundation As announced in a recent brochure, the 25-year-old Hans Merensky Trust has been converted to The Hans Merensky Foundation, its main objective being 'to promote and assist in the development of the resources of the Republic of South Africa and neighbouring territories articularly such natural resources as soil, water, minerals, flora and fauna-and to promote the health and welfare of the inhabitants; more specifically by research, experiment and demonstration and through the correlation and application of scientific knowledge'. Applications for S.A.I.M.M. membership and transfer Please note that new application and transfer forms have been issued.

Jan 11, 1974

Good blasting practices based on the careful application of explosive energy lead to significantly safer mining operations. Case studies demonstrate how the selection of the correct charge mass, explosive type and round design are vital for extracting the exact amount of rock required and preventing spurious damage to the remaining rock mass. In other cases the explosives are applied to precondition the rock mass, design rockburst resistant support, prevent damage to important excavations and reduce the exposure of miners to unsafe conditions. The Hybrid Stress Blasting Model is used to understand the explosive rock interaction and to illustrate and contrast good and bad blasting practices. In all cases, good supervision is required to continue safe mining according to the design. Keywords Blasting, safety, production, preconditioning, explosives, numerical modelling, drop raising, vibrations, and presplitting.

Jan 1, 2011

By H. L. Monro

Contribution by B. K. Martust I congratulate the author on his interesting paper. In my view, the establishment of the level at which South African gold output is at some kind of optimum is an interesting though somewhat academic exercise. Contribution by D. M. Hawkins* The thesis of the paper is a very interesting one, but, before it is used as the basis of any firm proposals to restructure the mining industry, which changes may be irreversible, one should be very sure that the basis of the calculations is sound. Contribution by P. J. Niewenhuizen* The hypothesis advanced by Mr Monro that the demonetization of gold in August 1971 introduced a major new policy variable, namely the supply-pricejdemand-price relationships, into the decision making process touches on a matter that has never really been given serious thought by the industry. Contribution by B. G. Kingsman* As a co-worker on the development of an econometric model for supply and demand in the world gold market with Mr H. L. Monro, it would perhaps be useful for me to make some comments on the various points raised in the discussions on his paper.

Jan 1, 1984

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11/2 inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219c. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: 1, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11-inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rulesfor Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219C. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: I, II, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTESAND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

[Council for 1994/95 President J.A. Cruise President Elect D.A.J. Ross-Watt Vice Presidents Senior P.D.K. Robinson Junior Dr N.A. Barcza Immediate Past President Dr H. Scott-Russell Honorary Treasurer D.A.J. Ross-Watt Members of Council J.P.W. Bennie Dr L.A. Cramer Prof. R.J. Dippenaar J.R. Dixon A.A.B. Douglas F.M.G. Egerton Prof. R.H. Eric B.R. Fleetwood Dr M.A. Ford Dr R.V.R. Handfield-Jones P.J. Knottenbelt R.P. Mohring K.C. Owen M.H. Rogers K.A. van Gessel P.M.T. White]

Jan 1, 1995

By N. Naude, W. P. Roux, O. Kaba

Ceramic filtration plates are used for dewatering slurries with high solid concentrations and particles in the size range of 30 μm to 150 μm. After extensive operating times, the ceramic filter plates at Minas Rio in Brazil begin to blind due to the precipitation of barium sulphate on the surface of the ceramic filter plate, which reduces the overall efficiency of the filtration process. Further research is needed to identify the barium precipitate phases on the blocked filter plates and its thermodynamic and kinetic behaviour in the system. A crystallography analysis was performed on the sample and the results showed that there are two different sets of precipitates formed on the filter plate: grey crystals which were large and scatted on the filter plate and red micro crystals that covered the entire surface of the filter plate. The red microcrystals on the sample were identified with XRD, which indicated that the sample contained barium sulphate in the mineral form barite. Experiments were conducted to determine the optimum conditions under which barium precipitation will occur. The conditions tested as a possible driving force for barium sulphate precipitation were the effect of temperature, pH and concentration. The pH and temperature ranges were pushed to both the lower and higher boundaries. The effect of temperatures as low as 15oC was studied and pH levels of 7 and upwards. The first nuclei started appearing at a pH of 7 but significant growth is promoted at higher pH levels. The X-Ray diffraction analysis confirmed the phase of the precipitates formed, and the orthorhombic crystallographic structure formed is a characteristic of barium sulphate. Keywords: Iron ore, barium sulphate, temperature, pH, concentration, morphology, and ceramic filter plate

Jan 1, 2020

By N. Mulaudzi

The use of SO2/air gas mixtures as an oxidant to precipitate Mn from Co(II) leach liquors was investigated. The effects of SO2/air ratio, pH and temperature on Mn precipitation were evaluated. It was found that the use of SO2/air gas mixtures resulted in significantly higher Mn precipitation kinetics compared to using air or pure O2 alone. The SO2/air ratio was varied from 0% to 6% SO2(v/v) in air and similar Mn removals were achieved at 0.75% to 3% SO2 at pH 3. The solution pH was varied from pH 2 to pH 4; Mn precipitation did not increase considerably from pH 2 to pH 3, but increased significantly at pH values higher than pH 3. Cobalt co-precipitation also increased as pH increased, with 1% Co co-precipitation at pH 3. An increase in temperature from 30°C to 60°C also increased Mn precipitation and 100% Mn precipitated at 50°C. Cobalt co-precipitation also increased significantly with an increase in temperature. An activation energy of 25 kJ/mol was calculated from the Arrhenius plot, which is an indication that the precipitation reactions were both chemically and diffusion controlled. XRD analysis showed that Mn precipitated in the form of Mn2O3 instead of MnO2 that was predicted from thermodynamic data. SEM and XRD analysis also revealed that the precipitate consisted mainly of gypsum or bassanite (99%), with the Mn containing phase (< 1%) distributed within the gypsum phase. The co-precipitated Co reported to the Mn phase. Keywords: manganese precipitation; SO2/O2 gas mixtures; cobalt solutions.

Jan 1, 2009

The February General Meeting of the Institute was held in Kelvin House, Johannesburg, on 19th February, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present forty-six Members, including Messrs H. E. Cross, A. R. C. Fowler, P. Lambooy, D. G. Maxwell, Dr J. T. McIntyre, Messrs J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), Messrs G. Abdinor, H. F. Allan, R. E. Barnes, M. M. Bayley, J. K. Boyd, R. R. M. Cousens, R. E. F. Cowley, D. Savile Davis, H. J. Davisson, C. T. Fenton, J. Fergusson, J. Fritz, M. L. Fitzgerald, J. M. Gosnell, J. C. Hall, S. A. Hancox, D. M. Jamieson, Dr D. G. Krige, Messrs J. E. V. Leeuwen, A. Louw, C. F. Louw, B. H. L. Leach, R. B. MacGillivray, C. S. McPhail, E. Margo, G. G. Nicolson, E. Pavitt, M. P. Pearse, F. O. Read, Dr M. D. G. Salamon, Dr H. S. Sichel, Messrs D. Storrar, S. G. Taussig, A. H. Taute, E. B. Viljoen and P. A. von Wielligh. Sixteen Associate Members, including Messrs S. T. Baron, W. M. Fitzpatrick, M. R. Fuller-Good, P. R. Garcia, H. G. Gericke, P. D. Hatfield, R. Hemp, G. S. Lee, Miss V. E. Marting, Messrs A. H. Munro, R. C. Power, O. F. Rheeder, G. C. Thompson and N. Zolezzi. Two Graduates, Messrs D. Bosley and J. C. Sutherland. Three Affiliates, Messrs R. K. Briggs, A. B. Cook and G. M. Thain. One Student, Mr P. W. Henrard. Twenty-three Visitors, including Messrs N. J. W. Bell, R. G. Bushell, A. Bryan, J. F. Cillie, C. M. de Beer, Dr F. H. Deist, Messrs D. S. Drake, P. G. du Plessis, R. W. Hodgson, D. M. Hawkins, S. C. H. Kearns, M. D. Labuschagne, L. Munro,R. Murchison and L. Robinson. Secretary, Mr D. C. Visser. Total present: Ninety-two. OBITUARIES The President: "It is my sad duty to announce the death of the following members of the Institute. Edward Frank Jud Bulman, Life Member, who joined the Institute in 1931 and passed away on 7th November, 1968. Elmar Fenton Chapin, Member, who joined the Institute in 1941 and passed away on 17th November, 1968. Solly Rabinowitz Rabson, Member, who joined the Institute in 1944 and passed away on 13th February, 1969. Mr. Rabson was the holder of two certificates of merit for papers presented to the Institute.

Mr R. C. J. Goode (President) was in the Chair. There were also present one hundred and thirty-six Members, including Messrs R. J. Adamson, Dr J. M. Bereza, Messrs M. Barcza, H. Britten, H. E. Cross, J. K. E. Douglas, G. W. Holl, Dr J. P. Hugo, Messrs C. J. Irving, P. Lambooy, Prof J. de V. Lambrechts, Mr D. G. Maxwell, Dr J. T. McIntyre, Prof R. P. Plewman, Messrs J. F. Reid, V. C. Robinson, H. Simon and P. W. J. van Rensburg (Council Members), G. Abdinor, C. B. Anderson, H. F. Allan, E. L. Atkinson, V. C. Barnes, J. F. Bennet, W. W. Bath, R. E. Barnes, C. L. Berrange, J. P. Buds, Dr W. Bleloch, Dr L. A. Bushell, Messrs D. L. Carson, D. D. Cornier, R. S. Cooke, R. R. M. Cousens, J. P. Coetzee, W. L. Cousens, J. Daniel, R. Daniel, D. G. Davies, S. K. de Kok, V. S. Dillon, B. S. Dykhouse, Dr H. G. Denkhaus, Dr R. S. J. du Toit, Messrs J. I. L. Edwards, R. C. Espley-Jones, J. C. Ferguson, D. T. Fourie, A. Frost, W. R. Flook, Dr N. P. Finkelstein, Messrs D. F. H. Grave, J. M. Gosnell, E. K. Gibson, R. W. Grout, E. W. Gray, J. S. Hay, F. G. Hill, H. N. Hepker, J. P. Hoffman, C. G. Hodges, D. M. Jamieson, Dr D. G. Krige, Dr N. P. Lategan, Messrs J. E. Laschinger, J. Levin, C. P. Linsell, J. O. Kempe, F. Q. P. Leiding, A. I. Lee, D. G. Malan, W. Malan, H. W. McCulloch, R. D. R. Munro, C. S. Macphail, Dr T. F. Muller, Dr A. J. Nel, Messrs S. C. Newman, G. G. Nicolson, G. Y. Nisbet, J. A. Papenfus, E. Pavitt, W. H. Pittie, P. C. Pirow, P. G. D. Pretorius, N. F. Peverett, R. P. Plaskett, M. P. Pearse, W. Pilkington, T. K. Prentice, Dr R. E. Robinson, Messrs R. B. Richardson, R. St. J. Rowland, R. J. Rouillard, F. O. Read, W. T. Ruhmer, D. Savile Davis, E. F. Statham, K. Smith, H. Simon, G. B. Stern, C. D. Storrar, Dr N. B. Strydom, Messrs J. H. Talbot, A. H. Taute, J. H. Taylor, G. W. Thiel, K. A. Tweedie, W. E. Vance, Dr H. J. van Eck, Messrs L. W. P. v. d. Bosch, P. A. von Wielligh, N. B. Vinson, S. J. Venning, W. M. Walker, D. T. Watt, Dr H. J. R. Way, W. T. L. Wayman, R. G. Williams, L. G. S. Wright and C. F. Ziervogel. Thirty Associate Members, including Messrs E. Collier, G. Douglas, D. H. Gray, H. G. Gericke, R. Hemp, N. M. Hayne, A. Hazell, P. M. Johnston, D. E. Love, Miss V. E. Marting, Messrs R. G. Matthews, P. Malpage, D. Nicolle, R. Pendreigh, J. J. Rosslee, R. W. Shearer, R. F. Taylor, G. C. Thompson and D. A. Viljoen. Three graduates, Messrs G. S. Giles, J. P. Hatfield and J. A. Jones. Five Affiliates, Messrs A. C. Collie, E. Collier, A. B. Cook, W. Jacobs and G. M. Thain. Two Students, Messrs C. J. Bircher and R. P. Henrard.

By R. Meyjes, P. Davies

Keywords: Pyrometallurgy, furnace, smelter, engineering company Metix is a private smelter engineering company wholly owned by its management. Its main lines of business in the ferro-alloy industry being: - turnkey smelter projects (LSTK) - engineering, project, and construction management projects (EPCM) - specialised furnace equipment comprising: ? complete electrode columns, including forged copper pressure rings and contact shoes, as well as fail-safe slipping devices ? water-cooled roofs ? bus-tube systems ? feed systems ? cooling systems ? linings ? off-gas systems ? tap-hole drills & clay guns - furnace power supply systems - ore agglomeration & sinter plants - feasibility studies & due diligence reports - technical consulting for investment banks - project procurement & cost control Metix management experience includes around 130 combined years of contacts and experience in the South African smelter industries. Over 30 furnaces have been built, for processes including FeCr (high, medium, and low carbon), FeSi, FeMn (high and medium carbon), SiMn (ultra low carbon), Si metal, and FeV.

Jan 1, 2006

Council and Standing Committees - 1982/83 President: Prof. A. N. Brown Vice Presidents: Prof. R. P. King and J. D. Austin Honorary Treasurer: Prof. D. G. Krige Immediate Past President: G. Y. Nisbet Members of Council: B. C. Alberts, R. H. English, P. T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G. G. Garrett, J. J. Geldenhuys, Dr A. K. Haines, P. N. Harris, H. E. James, Dr B. K. Loveday, Dr J. Lurie, D. G. Malan, G. Pienaar, B. E. Protheroe, Dr 0. K. H. Steffen, G. C. Thompson, Dr H. Wagner, Dr P. T. Wedepohl. Chairman, Witbank/Middelburg Branch: H. C. van Zyl.

Jan 1, 1983

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

Alexander Sutulov. Mineria Ghilena 1545-1975 (Mining in Chile 1545-1975). Santiago, Centre of Investigation of Mining and Metallurgy, 260 pp. (In Spanish). G. B. Rothenburg. Speciality steels. D.S.A., Noyes Data Corp., 1977. 270 pp. Witbank Middelburg Branch A General Meeting was held at the Wit bank Golf Club on 20th April, 1977, at 17h30. Treatment of waste water An International Research Symposium on New Processes of Waste Water Treatment and Recovery is to be held in London from 6th to 8th September, 1977. It NIM reports Report no. 1708 An examination of the suitability of various reducing agents for the production of ferrochromium. (27th Feb., 1975; re-issued May 1977). Report no. 1724 The preparation and reduction of chrornite pellets containing a reducing agent. (14th Apr., 1975; re-issued Mar. 1977). Report no. 1854 The interaction of pyrite, oxygen, and xanthate. (8th Mar., 1977). Report no. 1876 The ultrasonic determination of the mud level in a thickener and the resin level in an ion-exchange column. (6th May, 1977). Report no. 1878 The electrochemical dissolution of galena in aqueous solutions. (5th May, 1977). Report no. 1881 n-Octylaniline, a new extractant for noble metals.(28th Mar., 1977). Report no. 1883 The determination of iron, chromium, titanium, and tungsten by X-ray-fluorescence spectrometry. (31st Mar., 1977). Report no. 1889 Entropy relations in the formation of complexes of silver (1), mercury (II), and cadmium (II) with llwnodentate liyaruls. (5th May, 1977). Mechanics of granular materials A conference on the above subject is to be held in London on 8th and 9th September, 1977, under the auspices of the Institute of Mathematics and Its Applications.

Jan 1, 1977

The 101 st Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 12th August, 1998. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents H.E. Cross, D.G. Malan, P.W.J. van Rensburg Life Fellows J.B. Rolfes, W.C. Walmsley Fellows H.F. Boshoff, M.L.A. Fitzgerald, J. Humphriss Retired Fellows H.S. Botha, E.Collier, J.L. Curtis, A.H.H. Davison, D.I. Legge, B.D. McNeice, J.A. Northcott, D. de V. Oxford, S.S.K. Penney, P.C. Pirow, J. Pope, A.J. Rossouw, A.N. Shand, E.P. Smit, H.V. Solomon, S.G. Taussig

Jan 1, 1998

Results from a study undertaken at a Transvaal colliery on the feasibility of undermining an urban development by conventional bord-and-pillar mining operations in the No. 4 Seam of the Highveld Coalfield are discussed. Surface ground vibrations above production sections were measured, analysed, and then compared with well-accepted guidelines so that the expected effects of vibration on inhabitants and surface structures could be determined. The measurement and scaling of ground vibration from blasting are outlined, and the effects on humans and structures are discussed. It is concluded that residential areas can be safely undermined by conventional drilling and blasting techniques provided certain simple guidelines are followed.

Jan 1, 1987

The June General Meeting of the Institute was held in Kelvin House, Johannesburg, on 18th June, 1969, at 4.30 p.m. Mr J. K. E. Douglas (Vice-President) was in the Chair. There were also present fourteen Members, Messrs R. J. Adamson, F. P. Bath, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, and Mr P. W. J. van Rensburg (Council Members), Messrs B. F. Berry, A. F. Lee, J. E. van Leeuwen, G. G. Nicolson, N. F. Peverett, Dr A. G. Raper, Messrs E. R. Rudolph and H. R. Reid. Five Associate Members, Messrs T. D. Brown, M. R. Fuller-Good, J. S. Freer, Dr P. R. Jochens and Mr D. A. Viljoen. One Graduate, Mr P. G. Mrkusic. Five Students, Messrs N. A. Barcza, J. A. Cruise, R. P. W. Henrard, D. I. Ossin and J. C. M. Wethmar. Nine Visitors, Messrs M. Badenhorst, N. J. Bovey, H. H. Herold, Dr H. J. S. Kriek, Messrs M. S. Rennie, B. B. Segal, S. Selmer-Olsen, O. A. W. Strydom and B. Yates. Secretary, Mr D. C. Visser. Total present: Thirty-six. MINUTES The Vice-President: "May we confirm the minutes of the Monthly General Meetings held on 24th March, 16th April and 21st May, 1969 as published in the Journal?" Agreed. MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Wilfred Desmond Morgan, Abraham Kriek. Associate Members: Rodger Neville Hampson, Robert Richard Booth Lodge. Graduates: Beverley Hugh Waiters, Gwynne Hugh Johnston. Students: Colin Edward Alvery, Peter Marthinus Haikes, Charles Aubrey Husband, John Nowell Randell, Frederick Johannes Jacobus Blaauw, Johannes Andries Breytenbach, Peter Vos, Frederik Hendrik Coetzee, Petrus Nicolaas Jacobus Smit, Patrick Alien Boardman, Robert Nelson Guest. "May I welcome the newly elected members to the Institute." (Applause.) ELECTION OF SCRUTINEERS FOR THE 1969-70 BALLOT FOR COUNCIL The Vice-President: "In terms of By-Law 9.4, I now call for nominations for scrutineers for the 1969-70 ballot for CounciL" P. W. J. van Rensborg: "I wish to nominate Messrs R. C. J. Goode, V. C. Robinson, J. K. E. Douglas, P. Lambooy, D. G. Maxwell, H. Britten and H. Simon as scrutineers."

By R. J. Davidson, M. V. Nkosi, V. Veronsee

When activated carbon is used for the recovery of gold and silver from Witwatersrand gold-plant solutions, severe fouling of the carbon by calcium carbonate is experienced. Also, difficulty is encountered in the retention of the adsorbed silver on the carbon because it is displaced by gold. The acidification of plant pregnant solutions before they are contacted with carbon was therefore investigated as a means of overcoming these shortcomings. The results from batch laboratory experiments on the effect of pH on gold adsorption from plant solutions and from synthetic solutions of high ionic strength indicated reaction rate optima in the region of pH 5 and below pH I. The effect of pH on the equilibrium capacity constant for gold adsorption onto activated carbon was also studied, using both a plant solution and a synthetic solution of high ionic strength. In the case of the plant solution, the results suggested only a marginal change in carbon capacity for gold in the pH range 12 to 6, with significant increases in capacity at lower pH values. In the case of the synthetic solution of high ionic strength, the capacity constant was found to increase steadily as the pH was lowered from 12 to I. It was also found that the gold adsorption capacity of the carbon was significantly better for the synthetic solution. No precipitation of gold from the pregnant solution (gold content approximately 6 g/t) was noted as the pH was decreased to values as low as ,. However, about 25 per cent of the 0,6 g/t silver content was found to have precipitated when a pH value of 3,0 was attained. Further substantial precipitation of silver took place as the pH was lowered further. The investigation was extended by the passing of suitably acidified gold-plant solutions through one or more columns containing activated carbon. Preliminary results showed that the particle size of the carbon had a significant effect on the rate of gold adsorption. No displacement of adsorbed silver by gold was observed to take place at an influent pH of 5. In a typical continuous &apos;merry-go-round&apos; operation involving three columns in which gold was eluted from the lead column every 48 hours, effluent values averaging 0,001 g/t gold could be consistently achieved under simulated plant-operating conditions. The results were obtained at relatively high velocities of influent solution, resulting in very little hold-up of gold in the carbon-recovery circuit. More than 99,9 per cent of the gold and more than 99,8 per cent of the silver was recovered in the adsorption circuit, while the elution data indicated an average elution recovery of 99,8 per cent of the adsorbed gold and 98,2 per cent of the adsorbed silver. Elution of the carbon was carried out at 91 QC. This involved pretreatment of the carbon with a sodium cyanide solution, followed by elution with deionized water. At a loading flowrate of 66 bed volumes per hour, the indicated take-up of metals on the carbon in the lead column was as follows; 53 k g/t gold, 6 k g/t silver, 57 k g/t copper, 14 k g/t nickel, and I k g/t zinc. Only a trace of cobalt was adsorbed. At an elution rate of 1,7 bed volumes per hour, the lead column was found to be completely stripped in under 5 hours, with concentrations of gold in the eluate reaching 6 to 7 g/l. Besides the excellent adsorption and elution results obtained when acidified pregnant solution was used, no fouling of the carbon was indicated, and the pressure drop across the three columns was considered to be well within practical limits. When compared with conventional zinc precipitation, the carbon process would appear to have considerable economic merit, with strong indications that significant savings would be possible both in capital and operating costs. Further pilot-plant experiments, preferably on a gold plant, would be required before a meaningful cost comparison could be made with the existing process.

Jan 1, 1979