Search Documents

By D. B. Paterson

In view of decreasing head grades, the relatively high gold price, and recent developments in metal evaluation, an exercise was initiated to determine the extent of gold concentration, the mode of occurrence, and the areas of concentration within the run-of-mine milling circuits of Randfontein Estates Gold Mining Company (Witwatersrand) Limited. The total gold content of three of the thirteen run-of-mine mils in the Group was measured as a typical lock-up of approximately 200 kg per mil. The majority of this gold was concentrated either behind the grid-type body liners or within the pockets of the body liners. This paper is an account of the experimental procedure and the results obtained, and highlights possible means of limiting gold lock-up in future.

Jan 1, 1988

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting, and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power input over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge that was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified 'chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2012

By K. G. Philo, R. C. W. Webber-Youngman

mining, where data-driven decision making optimizes resource extraction, enhances safety, and ensures sustainability. The adoption of digital technologies like artificial intelligence (AI) and the Internet of Things has amplified the importance of digital information. However, the integrity and security of this information are paramount, leading to the exploration of blockchain technology as a potential solution for secure digital value exchange in mining. This research examines blockchain's capabilities, drawing insights from its applications in sectors like banking, government, healthcare, and entertainment, and evaluates their relevance to mining's core value chain processes. The study identifies blockchain's distributed ledger technology, cryptographic security, and decentralization as unique advantages that can revolutionize mining by enhancing transaction speed, reducing costs, and improving supply chain transparency and compliance with sustainability standards. Blockchain's transparent and auditable records can enhance business transparency, fostering trust among stakeholders, including investors and regulatory bodies. The technology's consensus mechanisms and smart contracts further promote trust in collaborative ventures. This research provides a foundational understanding for decision-makers in the mining industry to evaluate blockchain's feasibility and potential return on investment, guiding strategic planning and resource allocation for blockchain applications. By leveraging blockchain, mining companies can optimize operations, improve sustainability practices, and establish a robust foundation for future growth, positioning blockchain as a transformative technology in the sector

Jul 10, 2024

By G. van den Berg

Anglo Platinum has initiated a project to investigate hydraulic hoisting technology for platinum mines. Hydraulic hoisting systems are categorized as pumping, fluidizing feeder or displacement feeder systems. Positive displacement piston diaphragm pumps are most suitable for pumping systems but they require that the ore be milled prior to pumping. Fluidizing feeders are unsuitable for platinum ore applications due to the large percentage of fines in the ore. The three-chamber pipe displacement feeder has been most widely used for hydraulic hoisting and is the most suitable technology for platinum mines. Eight hydraulic hoisting applications covering pumping and displacement feeder technologies are reviewed. The key factors to be assessed in selecting a hydraulic hoisting system for a platinum mine are discussed. A typical platinum mine configuration will comprise an ore preparation plant (to produce -15 mm material through screening or crushing), motive water pump on surface, high pressure water pipeline from surface to underground, ore slurrification plant, three-chamber displacement feeder, and a high pressure slurry pipeline to surface. The water and slurry pipelines are housed in a purpose drilled borehole. A hydraulic hoisting system selection chart is presented. A 150 mm diameter system with a 25 MPa pressure rating is required to hoist 60 000 t/m from a depth of 1 200 m. Generic capital and operating costs are presented . A major potential advantage of hydraulic hoisting is that the fines, which contain a high percentage of PGMs, are captured underground and transported directly to the concentrator. Hydraulic hoisting technology is ideally suited to providing supplementary hoisting capacity to existing shafts that have reached the skip hoisting capacity limit. The main advantage for new shafts is the potential to significantly simplify underground rock handling and transportation. All hydraulic hoisting system components are proven. The only risk area is the wear rates of the valves and piping. Current estimates are based on gold ore. The business cases investigated show that the financial viability of the installations are not sensitive to wear rate. Hydraulic hoisting is technically feasible and financially attractive for platinum mines. Keywords: Hydraulic hoisting, slurry

Jan 1, 2004

By M Scott, J J. McEwan

Silver and silver alloys tarnish readily by the formation of tarnish on the surface when exposed to a wide range of sulphur-containing atmospheres. This tarnish is unsightly and undesirable and can be removed either with a silver polish or a chemical dip. Polishes are, however, not suitable for irregular and embossed surfaces such as on coins, medallions and jewellery items, because of uneven removal of the tarnish layer and excessive wear. Successful tarnish protection can be achieved by either storing the items away from the aggressive atmosphere or by coating/treating the exposed surfaces with a protective layer. Storage is feasible for collections but is not suitable for items that are handled or worn regularly, such as jewellery. A number of commercial coatings and treatments have been developed, but to date there has not been a systematic evaluation of tarnish protection. This paper details the performance of a range of generic coatings in an accelerated tarnish test. The degree of tarnish was evaluated by means of loss in reflectivity and change in colour. Four coatings/treatments improved the tarnish resistance of silver by more than tenfold. These include an organic lacquer, rhodium electroplating and an organic self-assembled monolayer (SAM) conversion coating. Research is continuing to optimise these coatings. Keywords: silver alloys, tarnish resistant coatings, silver polishes.

Jan 1, 2006

By S. Fletcher, C. Calle, K. Constanti-Carey, R. Ruzbacky, M. D. Horne

Laboratory test-work has established that two classes of redox catalysts based on anthraquinone and bipyridinium derivatives are effective in accelerating the rate of removal of metallic iron from reduced ilmenite (RI) in the aeration step of the Becher process. Two water-soluble anthraquinone derivatives are efficient: 9,10-anthraquinone-2,6-disulfonicacid, disodium salt (catalyst AQ-2,6) and 9,10-anthraquinone-2-sulfonic acid, monosodium salt(catalyst AQ-2). When 0.2 per cent w/v of either was added during aeration the rate of metalliciron removal was accelerated by two to three times. Furthermore, the addition of either compound resulted in magnetite (Fe3O4), the iron oxide phase preferred in commercial practice, being formed. However, both AQ-2,6 and AQ-2 were rapidly lost from solution during aeration although their catalytic activities persisted even when their concentrations in solution were low(<0.05 per cent w/v). The negatively charged anthraquinones were lost from solution most probably by adsorption onto the magnetite that has a net positive charge at the pH values encountered during aeration. To address this problem, the catalytic activities of positively charged bipryridinium derivatives were tested. Two water-soluble bipyridinium compounds, paraquat (1,1’-dimethyl-4,4’-bipyridinium dichloride) and diquat (6,7 dihydrodipyrido [1,2-a:2’,1’-c] pyrazinediiumdibromide), were found to significantly accelerate the rate of removal of metallic iron from reduced ilmenite, and both gave magnetite as the oxide product in the laboratory tests. Moreover, recycle tests showed they were not lost from solution as quickly as were the anthraquinone derivatives. Results in larger scale plant laboratory reactors also showed a significant increase in aerationrates when diquat was added and magnetite was again the oxide formed. However, the oxygensupply to the reactors was insufficient to achieve the maximum effect of the catalysts on theaeration rates. The limited supply of oxygen in a full scale aerator may prevent the application ofthe catalysts in a commercial Becher operation. Keywords: Becher process, aeration, anthraquinone, bipyridinium, redox catalyst, reduced ilmenite

Jan 1, 2003

By R. T. Jones

"SynopsisScientific progress relies on the publication of ideas and experimental results that can be replicated, tested, and improved over time. The first printed book on metallurgy to have been published in Europe is considered to be De la Pirotechnia, written in Italian by Vannoccio Biringuccio, and published in Venice in 1540. Together with De Re Metallica, written by Georgius Agricola and published in Latin in 1556, this can be considered to mark the start of scientific and technical literature in this field. Scientific publishing of journal papers has been in existence for 350 years, since the world&apos;s oldest and longest-running scientific journal, the Philosophical Transactions of the Royal Society, was first published in London in 1665.The nature of scientific societies has changed significantly since the early days when regular meetings were held to discuss science and conduct experiments, and the reading of scientific papers took place, and publication of papers was undertaken to record the proceedings of meetings, often including rather robust debate. In today’s world, there is a plethora of publications, and it is close to impossible for anyone to keep up with the vast flow of information. International conferences with hundreds of presentations have taken the place of the local meetings that used to discuss a single paper or experiment. In this frenetic environment, it is essential that researchers are able to trust the material they read.The system of peer review is used to maintain standards and to improve the quality of papers. This vital system is, however, significantly flawed. There is little incentive for reviewers to invest sufficient time in picking up all errors in publications, and any ineptitude on their part is usually protected by anonymity. It has reached the point where some reviewers have mistakenly permitted the publication of hoax papers deliberately presented with a complicated scientific facade. In light of such astounding inadequacies, perhaps a more open review process would be an improvement. Electronic publishing allows errata to be linked to the original papers.There is an increasing trend towards open access for papers in scientific journals and conference proceedings, which helps to reach as wide an audience as possible. This also supports the statement in the Universal Declaration of Human Rights, which says ‘everyone has the right freely to … share in scientific advancement and its benefits’."

Jan 1, 2015

By H. E. James

Much has been said and written about the need to reduce South Africa&apos;s dependence on gold. To compensate for the decline in the country&apos;s foreign-exchange earnings resulting from the phasing out of gold, which must inevitably occur at some future date, a far higher priority will have to be placed on the mining, beneficiation, and export of the 59 other mineral commodities produced in South Africa. The basic strategy of the mining and metallurgical industries should be to move from the traditional approach of establishing a resource base to the establishment of a market base; to turn from production orientation to market orientation; and to rely less on exploration and economies of scale and more on process innovation and product development. The enthusiasm, entrepreneurial spirit, and commitment of the leaders in the mining and metallurgical industry will clearly be of decisive importance in the establishment of new industries for the beneficiation and export of added-value mineral-based products. The State can make a significant contribution by the provision of a welldeveloped and efficient infrastructure, including rail and harbour facilities, communications and health services, roads, and of electricity and water supplies. In our search for a new development strategy for the beneficiation and export of South Africa&apos;s minerals, we need to recognize that no one nation has all the mineralresources that it needs. Commercial and strategic manipulation of mineral supplies should no longer be tolerated. The future of the human species lies in international cooperation and in a greater understanding of the limitations of the world we live in.

Jan 1, 1985

By R. C. M. Minnitt, W. Dr. Assibey-Bonsu, F. A. Camisani-Calzolari

Born in Bothaville (OFS) on the 26th August 1919, Daniel G. Krige grew up in Krugersdorp on the West Rand. Hematriculated from Monument High School in Krugersdorpin 1934 at the age of 15 and graduated with a B.Sc. (Eng.)degree in mining engineering from the University of the Witwatersrand at the end of 1938 (age 19). In 1938 he joined Anglo Transvaal where he worked on a number of gold mines until 1943, gaining a wide range of valuable practical experience in surveying, sampling and ore valuation. He then joined the Government Mining Engineer’s Department where he worked for 8 years during which time he participated in the uranium negotiations with the British and American authorities and designed the uranium pricing formula for the contracts which led to the establishment of South Africa&apos;s profitable uranium industry in the early 1950s. During the same period he began his pioneering work in the application of mathematical statistics to the valuation of new gold mines using a limited number of boreholes and of ore reserves for existing mines. His early papers in the application of mathematical statistics, some republished in French, created world-wide interest that led to the development of the science and concepts that surround the spatial evaluation of mineral resources and reserves known as geostatistics. This technique has contributed to improved ore evaluation techniques as well as the reduction of the financial risks associated with investment in mining enterprises. Furthermore, it led to the recognition of his contributions to the evaluations of mineral deposits through the coining of the term ‘kriging’ that is used to describe a spatial mineral evaluation process known and practised in international mining circles. He continued his work in geostatistics throughout his career as Group Financial Engineer of the Anglovaal Group until his retirement in1981 and afterwards for ten years as Professor of Mineral Economics at the Witwatersrand University. He is still active as a consultant and is a registered Professional Engineer. He has published some 90 technical papers both locally and overseas, some in Russia, and has lectured and participated in international congresses in many countries. His contributions were recognized by the Witwatersrand University through the award of the D.Sc. (Eng.) degree in1963, by three honorary degrees (from the universities of Pretoria, UNISA and Moscow State Mining University), by many awards from the South African Institute of Mining and Metallurgy, the International Association for Mathematical Geology, Die Suid Afrikaanse Akademie vir Wetenskap en Kuns, the SME of the American Institute of Mining Engineers, the International APCOM Council in1999, the University of Antofagasta in Chile, and by the South African President (Order for Meritorious Service, Class 1, Gold). He has served on various Government committees, notably that for State Aid for gold mines (1967/8) and designed the State Aid formula which enabled many mines to survive a period of low gold prices; also various taxation committees, and the mining mission to Iran in 1974. He is a fellow and/or honorary life member of various technical societies locally and overseas, including the Royal Society of South Africa. During the period in the Government service he also handled several of the post-war lease applications in the Free State and Klerksdorp goldfields. The fact that decisions on new gold mines of critical importance to the State and the economy as a whole, were being taken on a limited number of drillholes without any scientific analysis of the risks of failure, stimulated him to start basic research into ore evaluation. His approach was based on the application of Mathematical Statistics to these problems, an approach of which very little was known world-wide at that stage but which had already been initiated in South Africa by Sichel via the lognormal frequency distribution model. In Krige&apos;s 1951 paper published in the Journal of the Chemical, Metallurgical and Mining Society of South Africa he covered the statistical explanation of the conditional biases in ore block valuations and stimulated the use by several gold mines of regression corrections for routine ore reserve valuations, a technique which, in effect, was the first use on an elementary basis of what is now known as kriging. His 1952 paper introduced, inter alia the basic geostatistical concepts of ‘support’, ‘spatial structure’,’ selective mining units’ and ‘grade-tonnage curves’. His 1951 paper was based on his M.Sc. (Eng.) thesis submitted in the Department of Mining Engineering to the University of the Witwatersrand, and expounded his pioneering work in geostatistics in more detail. His early research papers that had stimulated interest in several mining circles overseas, were republished in French in1955, resulting in a major research effort by French mining engineers in this field. This, in turn, led to the establishment of the now world-renowned French school of ore evaluation in Fontainebleau, Le Centre de Geostatistique de l’École des Mines de Paris. As the Group’s Financial Engineer at the Anglovaal Head Office until his retirement in 1981, he was responsible for

Jan 1, 2003

By C. Yi, M. Onifade, B. Genc, S. Dineva, T. Zvarivadza, M. Khandelwal

Deep hardrock mines worldwide increasingly face rockbursts as mining depths increase. These events result from the accumulation and sudden release of stress, causing rockmass damage and posing major safety and operational challenges. This paper focuses on destress blasting as a critical strategy to mitigate rockburst hazards. Although limited practical experience exists in Swedish deep hardrock mines, international case studies demonstrate that, when well implemented, destress blasting redistributes peak stresses by promoting controlled fracturing around mining excavations. The success of such techniques is highly dependent on site-specific factors such as stress regime, rockmass brittleness, structural geology, and blast layout. Although destress blasting is especially effective in massive, brittle rock under high stress, typical conditions for strainburst prone environments, its design cannot rely solely on numerical models. Simulations can offer preliminary evaluation of stress redistribution trends and guide early design assessments but their current limitations, including sensitivity to input data and simplified fracture mechanics, mean they are best used as supplementary tools rather than final decision-makers. Field trials, supported by microseismic analysis and fracture mapping, remain essential for validation. The study critically synthesises international experiences and presents a structured framework for destress blasting design, offering practical and academic perspectives aligned with Swedish geological conditions to support safer and more efficient application in deep hardrock mines.

Jun 27, 2025

By S. D. Dladla, S. Ramsamy

The majority of the tailings dam operations in South Africa will be required to comply with the new Global Industry Standard on Tailings Management (GISTM) within the next one to three years, depending on the dam classification and the requirements of the respective investors and insurers. With up to 72 auditable requirements, the implementation of the Standard needs careful planning and prioritization. This paper focuses on the practical steps to GISTM compliance for tailings facilities in operation in South Africa. The discussions are based on current practices, South African regulations, and industry standards requirements. The possible changes in dam classifications and the associated requirements are presented.

Jun 2, 2022

By S. Burks

This paper develops the themes explored by the authors at the Fourth International Platinum Conference,. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: > An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated > An existing operation with an integrated portfolio of mines, concentrators, smelter, and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets > An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated > An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the owner&apos;s team.

Jan 1, 2013

Ground control problems in the form of large dome or wedge collapses have been experienced at Tau Lekoa Mine since production began. Crush pillars in various configurations have been used and through a process of trial and error the current pillar layout has been derived. A strike pillar layout is used and additional mid-panel pillars are left spaced a maximum of 10m or 16m apart, depending on conditions and mining direction. Pillar spacing is based on an empirical relationship between fallout height and pillar spans. Analysis of the spatial distribution of large falls of ground indicates that there may be several geotechnical relationships contributing to stable pillar spans. The current focus is to define the relationship between geotechnical areas and hangingwall stability so that area specific support strategies can be formulated that could result in increased production efficiencies. Depuis le début de la production, la mine Tau Lekoa a connu des problèmes de contrôle au sol, sous la forme d’effondrements de grands dômes ou coins. Des piliers d’écrasement, dans des configurations variées, ont été utilisés et une série d’essais a résulté en la disposition de piliers en cours. Une configuration de piliers de direction est utilisée, et des piliers mi-panneau supplémentaires sont laissés, espacés d’un maximum de 10m ou 16m, selon les conditions et la direction de la mine. L’espacement des piliers est établi sur une relation empirique entre la hauteur des retombées et les intervalles entre piliers. L’analyse de la distribution spatiale de grandes tombées de terrain indique qu’il peut y avoir plusieurs relations géotechniques qui contribuent à des intervalles de piliers stables. L’intérêt présent est de définir la relation entre les zones géotechniques et la stabilité du toit, pour pouvoir formuler des stratégies de support spécifiques à un endroit, ce qui entraînerait des accroissements de production. Bodenkontrollprobleme traten seit Produktionsbeginn in Form von grossen Keil oder Dachhaubenbrüchen in der Tau Lekoa Mine auf. Bruchpfeiler in verschiedensten Konfigurationen wurden verwendet und auf Grund empirischer Fakten wurde das gegenwärtige Pfeilerlayout abgeleitet. Ein Layout für Strukturpfeiler wird verwendet und zusätzliche mittig situierte Pfeiler in einem Maximalabstand von 10m bis 16m installiert, abhängig von den Konditionen und der Vortriebsrichtung.Der Pfeilerabstand basiert auf dem empirischen Verhältnis Fallhöhe und Pfeilerspannweite. Die Analyse der räumlichen Verteilung großer Bodenabsenkungen deutet an, daß es einige geotechnische Verhältnisse geben kann, die zu stabilen Pfostenspannweiten beitragen. Der gegenwärtige Fokus soll das Verhältnis zwischen geotechnischen Bereichen und Stollendeckenstabilität definieren, damit bereichspezifische Unterstützungsstrategien formuliert werden können, welche in erhöhter Produktionsleistung resultieren könnten.

Jan 1, 2003

By D. A. Singer, J. C. Griffiths

"One of the most useful approaches to a complex problem is to model the system which gives rise to the problem and to perform simulations through the model to find appropriate solutions. The Engel Model may be used as such a simulator to investigate the problem of the exploration for natural resources.The Engel Model is based on a two-stage search procedure in which a known area (A) which contains m prizes is subjected to search by n coverings. During the first-stage search the sensor system records signals which may be a response from prizes (that is, true signals) or may be false. Signals tend to cluster around a prize and a cluster size consists of s signals. If a circle of radius R is drawn around each signal some will overlap and the overlap from s signals contains a prize. The cost of a single covering in which each point of the area comes under observation once, is designated E1. Second-stage detailed search is expensive and is confined to areas of overlap of s circles; it leads to the location of prizes. Second-stage search of the whole area costs Ea units. The expected value, V, of a prize is known and its development cost is E3 units.The sensor system characteristics are defined by the circle of radius R around a signal, which should be small compared with the total area A and enters the model as a parameter a x R2/A. The probability of a false signal during a single covering of a circle of radius I is a known constant, A.This model was applied to the search for uranium ore bodies using two different types of occurrence. In the first, the Wyoming Basin type, the area is relatively large (A = 1 496 square miles) and a few (m = 4) large prizes occur (expected value V = $30 million). In the second area, which represents the Ambrosia Lake region of New Mexico, the area is smaller (A = 212 square miles) and contains many (m = 200) smaller prizes (expectedvalue of a prize V,$2 million). The three costs, E1, E2, E3, are adjusted to the different circumstances in the two areas.Simulations were performed using n = 1 to 40 coverings with cluster sizes s = 0 to 19; the radius R was varied from 0.52 to 3 miles (and, therefore, a = 0.002 to 0.133 0, respectively, dependent on the area of interest). The value of A was varied from 0.01 to 0.10.Profitable programs were found over a wide range of the parameters; the two areas required different strategies to achieve maximum profit. In the Ambrosia Lake region a few passes (n = 4 to 6) with small cluster sizes (s = 2 to 6) are more profitable, whereas in the Wyoming Basin region a large number of passes (n = 35 to 40) and cluster sizes of s = 5 to 10 are most profitable.As pointed out by Allais (1957) the larger prizes are the most important in deciding the successful outcomes of exploration programs, and the profit margin in the search for a few large prizes is sufficient to yield success over a wide range of programs. Such programs require very large investments if they are to be successful.To refine the Engel Simulator as a decision-maker in selecting the most profitable exploration programs it is necessary to obtain firm estimates of the sensor system characteristics, that is, of R, a and ? (lambda)."

Jan 1, 2014

Statistics is essentially a study of variability, the use of some suitable mathematical model representative of such variability, and the application of this inferred pattern of behaviour to practical problems. Probability theory is the mathematical structure devised for providing models for chance happenings. Perhaps the simplest example of a chance happening is the result obtained in tossing a coin. Although the result of a single toss can never be predicted with certainty, there is no reason why in repeated tosses the expectancy of heads and tails should not be equal. In such a case the outcomes of the experiment are said to be equally likely, so that the probability of obtaining heads (or tails) is 1 in 2, that is, 0,5. This simple probability .model refers to a &apos;mathematical&apos; or &apos;unbiased&apos; coin. Whether such probabilities are meaningful for actual coins tossed in any particular way is a matter for experience to determine. Probability models have also provided the basis for representing observed variability in cases where the actual under- lying probabilities are only partly known or defy analysis. A typical example of the latter case is the variability observed in the values obtained from gold or other ore samples. The interacting natural forces which gave rise to this variability are obviously very complex and are unlikely ever to be unravelled completely. In spite of this, probability theory and the more recent geostatistical theories have provided us with models which can represent this variability on a reasonable basis. Applied statistics and geostatistics must therefore never be accepted as exact mathematical sciences. Furthermore, a basic and essential concept is that in the type of applications covered in these notes, no model must ever be accepted as necessarily the final and exact answer to the problem; thus, any model must prove and continue to prove its appropriateness in practice, preferably by follow-up comparisons.

Jan 1, 1981

By B. van Beek, J. Ndlovu, K. T. Hara, J. M. A. Geldenhuis

This paper describes the development of an alternative technique for measuring the matte level height in sulphide smelting furnaces. The initial studies involved applying electrochemical oxygen probes in a smelting furnace to measure the oxygen potentials of the matte and slag phases. However, these measurements were not successful as a result of low temperatures, preventing there ference electrode from attaining equilibrium during the measurements. These trials were followed up by using oxygen probes containing a (Mo + MoO2) reference electrode instead of the(Cr + Cr2O3) reference electrode used previously. It was shown that with some further development work, it should be possible to measure the oxygen potential of these mattes accurately. Further measurements were performed with a magnetic sensor in sulphide mattes. It was shown that an electronic signal, which is proportional to the magnetic susceptibility of the surrounding material, was generated during immersion into liquid matte. These measurements were extended and done in a smelting furnace. Initial results indicated that when the magnetic sensor was dipped through the slag layer into the matte, a signal was generated as soon as the sensor came in contact with the matte. Measurements are ongoing in order to record (on a computer for improved accuracy) the signal as a function of distance when the sensor is immersed through the slag layer into the matte phase. The magnetic sensor measurements may be the solution to a matte level measurement problem that has existed for a few decades in matte smelting furnaces.

Jan 1, 2004

By S. Pule, Z. Ndabezimbi, A. Hefer, E. Cupido

This article outlines various projects implemented at Rand Refinery to reduce effluent generation and freshwater consumption. The refinery generates about 2800 m³ of effluent annually and has initiated projects such as granulation water recycle and silver leach optimisation to address these issues. The granulation water recycle project has successfully reduced effluent volumes, while the silver leach optimisation has further decreased effluent by implementing stoichiometric addition of HCl and NaClO3. The vibratory shear enhanced processing (VSEP) trial showed promising results for gold recovery from wastewater, though further trials are recommended. The water savings of the effluent reduction projects are monitored by measuring the amount of effluent pumped to service yard effluent storage facilities with the use of flow meters connected on SCADA. Since the effluent reduction initiative of granulation effluent recycle in FY23, the effluent reduced to 2676 m³. In FY24, the stoichiometric addition of HCl and NaClO3 was implemented in the silver leach process, further reducing the effluent to 2083 m³.

Mar 5, 2025

By J. O. Claassen

"A study conducted at 22 operating mines in the southern African region indicated that each mine employs about five management and improvement methods with roots in the manufacturing industry. All respondents reported the implementation of cost-saving initiatives, whereas 80% of the mines are affected by restructuring. TQM, Six Sigma, BPM, and TOC were found to be the most prevalent manufacturing management and improvement methods used. A mechanistic vs systemic evaluation of the suitability of these methods to bring about positive change in the industry suggested that complex, ever-changing mining systems are better served by a systemic flow-based approach, which is embedded in methods such as TOC, JIT, TPS, and Lean Production. These methods, however, lack industry presence, possibly because they do not effectively deal with the unique challenges associated with the mining environment. It is argued that successful mining business management and improvement depends on management’s ability to deal effectively with mining industry-specific requirements, the integration of the geologymining- plant system, and the implementation of systemic flow-based principles in all aspects of mining. IntroductionThe study aims to explore the use of manufacturing management and improvement methodologies in the southern African mining industry. Considering the unique challenges associated with mining operations, attention is given to the applicability of the most commonly used manufacturing methodologies in the tactical, operational, and strategic environments. The article endeavours to stimulate more research and debate in an unexplored field of study."

Jan 1, 2016

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d&apos;interface et un modèle constitutif sont développés. Dans le but de valider l&apos;applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003

By B. G. Russell

A wide range of minerals is found within the Republic of South Africa, many of which are exploited to a greater extent than in similar deposits found elsewhere. It is often asked whether this is atributed to the high grade of the ores encountered in this country, or whether such factors as fiscal and Infrastructural incentives create an economic climate that has en bled the mining industry to successfully extract and market minerals at a profit. This paper views South Africa&apos;s mineral resources in a regional and global context In an attempt to place the country&apos;s geological wealth in perspective. It represents the author&apos;s own Views, and not necessarily those of the Department of Mine al and Energy Affairs.

Jan 1, 1986