Search Documents

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

West Virginia ranks second in the nation in coal production, surpassed only by Wyoming, and usually accounts for 15 to 20percent of the nation's total annual production. Cod occurs in seams of minable thickness in all but nine of the state's 55 counties. There are two coal- producing regions, the northern field and the southern field. West Virginia coal is mined by both underground and surface methods. Underground mines in West Virginia account for a major portion of its coal production. Surface mines are generally contour operations and, especially in the southern field, are in steep slope areas, with slopes greater than 20 degrees. Many of the surface mines remove multiple seams. Recoverable reserves in West Virginia total in excess of 55 billion tons of bituminous coal. West Virginia's regulatory program was conditionally approved on January 19, 198 1. Its Abandoned Mine Land Program was approved February 23,198 1, with emergency authority granted on August 26,1988.

Jan 1, 1992

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

By Steven J. Page, John A. Organiscak

The amount of airborne respirable dust generated from break- age of different coals varies widely. This research was conducted to identify the facets of airborne respirable dust liberation from the coal product. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals to investigate the various factors influencing airborne respirable dust generation. Bituminous coal samples from 8 mines (5 U.S. and 3 Polish) were uniformly prepared and processed through a double roll crusher located in a low air velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific quantity of airborne respirable dust generated. The results of this investigation build upon previously published results, which indicated that a combination of several factors are associated with the generation of airborne respirable dust. One factor involved is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. However, since coals of high moist fuel ratio (high rank) are generally more extensively cleated, it is suggested in the present work that the degree of cleating is directly responsible for the quantity of respirable-sized particles produced in the crushed product material for eastern U.S. coals. This is implied by the relationship of ash content and at least one mineral constituent (pyrite, determined from pyritic sulfur analysis) to the percentage of airborne respirable dust. To validate this hypothesis, a description is offered that is based on known coal petrography. Another key factor is the effect of air dry loss moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The air dry loss moisture factor appears to control the amount of airborne respirable dust that is liberated from the product. The resultant effect of these factors is that different percentages of coal particles smaller than 10 µm are dispersed as airborne respirable dust with a well-defined peak in the normalized airborne respirable dust for a narrow range of air dry loss moisture - ash ratios. A clear delineation of coals, based on well-known proximate analysis characteristics, that generate the most respirable dust appears to be possible. It was also shown that the dust-generating characteristics of coals could be reasonably described by both the moist fuel ratio

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By G. W. Marks, A. H. Roberson

"Previous investigation 4/ has demonstrated that some of the aliphatic amines are suitable absorbents for 302, This paper reports the results of physical studies of a number of such amines with the object of determining which is most favorable as an absorbent.Monoethanol amine, diethylene triamine, and triethylene tetramine appear to be the most promising of all the amines studied, and most of this report has been devoted to studies of the physical properties of their aqueous solutions, which contain varying amounts of SO2.PURITY OF MATERIALSAll of the amines used were of commercial grade, because the primary object of this research was the investigation of a proposed works process rather than the accumulation of scientific data.The aminoethyl derivitives of ethylene diamine, namely, diethylene triamine, triethylene tetramine, and tetraethylene pentamine, only recently have been produced commercially. The chemistry of aliphatic amines is complex, and these newer derivitives have not been investigated, completely. Chemically pure material is not on the market, and since definite physical standards have not been published, one could not be assured of a pure product even if the commercial material was refined.The compilation of physical constants for the pure amines would involve much time—consuming effort without materially enhancing the value of this paper, as this work was not devoted to the development of fundamental standards."

Oct 1, 1938

By J. Kruttschnitt

This paper, describing the mining operations at Mount Isa Mines, is one of a series covering mining methods and costs being published by the United States Bureau of Mines. The Mount Isa property has been in operation since June 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods. Stoping methods have been designed to apply to parallel lodes ranging from 10 to over 100 feet in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sublevel stoping method for mining the sulphide ores.

Jan 1, 1937

By A. L. Peyton

Manganese-oxide minerals occur in irregular pockets distributed through the residual clays of the Cartersville district, which lies 45 miles north-west of Atlanta in Bartow County, Ga. The district produces, or has produced, limonite, barite, specular hematite, ochre, ferruginous manganese, manganiferous iron are, as well as manganese. Bureau of Mines engineers have visited the district on three occasions - in December 1939, February 1941, and October 1942. During the visit of February 1941, 80 tons of samples of manganese-bearing clays were taken from seven properties for ore-dressing tests, which were conducted at the Bureau of Mines laboratory at Rolla, Mo. The. October 1942 visit was for the purpose of reappraising the district in the light of knowledge gained from the ore-dressing studies and to prepare a plan for the district's development. Exploratory drilling was begun in March l943 and was continued until June 1945. Nine properties were explored that, roughly follow a line beginning near Cartersville and extend to a point 2 miles northeast of the village of White. The work consisted of bulldozer trenching, rotary bucket churn drilling, sampling, and analytical determinations. The manganese district is 18 miles long with a maximum width of 7 miles at Cartersville, which lies at the center of the district. The work of the Bureau was confined to the northern half of the district between Cartersville and Pine Log. The properties explored comprise but a small portion of the Potential producing area.

Jan 1, 1949

By R. J. Gunderman

Explosionproof electrical enclosures for coal mine face equipment have been of the same basic design for many years without significant change. Characteristics for potential improvement were investigated through interviews, visits to mines and studies. Improved safety, health and productivity were the goals. Areas identified for improvement included rapid venting of pressure build-up due to an internal explosion, quick and easy entry or removal of cable entrances, and a quick and easy cover removal for rapid component access. Concepts were identified and evaluated, and the more promising devices were fabricated and tested. Encouraging results from initial tests led to further design refinement and establishment of design guidelines. These design guidelines for a pressure vent and for an elastomeric grommet type cable entry are described along with the testing used. An application for an experimental permit was requested from MSHA. After test and evaluation experimental permit #396 for evaluation in an underground coal mine was granted.

Jan 1, 1980

By John C. Cook

Channel sand bodies ("wants" or "cutouts") are deposits of barren, hard sediments which interrupt production and pose safety hazards when encountered in underground coal mining. To locate these costly impediments to mining in advance, from the surface of the ground, the seismic reflection method is recommended. High-resolution (high frequency) techniques for shallow seismic exploration of coal beds have been worked out and are reported here, including a field example. Newly-developed high-frequency, digital recording equipment was used, together with light-weight shot-drilling equipment and a variety of down-hole seismic impulse sources. Techniques for rapid but complete coverage of a coal prospect area with a crew of 2 to 6 men n 2 or 3 vehicles are described in detail.

Jan 1, 1976

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944

By T. J. Ballard

"INTRODUCTION The Buck. Creek corundum area of Clay County, North Carolina, includes one of the largest single masses of peridotite outcrops in the whole Appalachian Range and has been described by Pratt, an early authority on corundum, as offering one of the best potentialities for corundum production in North Carolina.Two principal types of corundum deposits are found at Buck Creek the vein type and the corundum-bearing amphibolite dikes.The vein deposits occur in structural fissures that strike north to northeast in a gangue of feldspar, zoisite, an, chlorite. The corundum is generally coarse-grained and good-quality. The corundum content varies from several percent to 50 percent.The corundum in the amphibolites is more or less disseminated through the dike, is generally lower-grade, and is less in quantity, than the vein corundum. About 50 percent of the amphibolite corundum is coarse enough for snagging-wheel grade but is difficult to separate from the amphibolite.Production from the Buck Creek area has been small and came mainly from high-grade pocket in the vein deposits. Pratt 3/ reports 300 tons of corundum ore was produced to about 1896. No record of subsequent production is available.The critical shortage of corundum during the war, due to transportation difficulties and the depletion of deposits abroad, prompted the Bureau of Mines to investigate domestic reserves.After a favorable report was obtained on the Buck Creek area, the Bureau began exploration of the deposit in September 1943 and continued until February 1945."

Apr 1, 1947

By David C. Oyler, Dennis R. Dolinar, Christopher Mark, Craig S. Compton

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends. If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the “full resistance zone” of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. v

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

By Harlan A. Walker

This paper on the mines of El Potosi Mining Co. is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Grateful acknowledgment is made of the helpful suggestions and criticisms offered by the management, together with the assistance of the mining staff in preparing maps and drawings and of C. L. Thornburg, mine geologist, in preparing the section on geology.

Jan 1, 1934

By David Garry, Michael J. Brnich, Lynn L. Rethi, Henry P. Cole, William J. Wiehagen, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet and the trainee's questionnaire. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.1 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Supervisors, Safety Personnel and Accident Investigators Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Developing a strategy or plan to prevent slips and falls Following correct procedures in conducting an accident investigation Preventing unsafe work practices Recognizing and instituting hazard controls in the section Identifying and implementing safe work procedures Location: Underground coal mine section Problem: You have been the general mine foreman at White Rock Mine for 4 years and have worked at this mine for 12 years. The mine superintendent calls you into his office. He gives you an accident report of an employee in 4-G section who was injured while carrying rock dust bags from the rock dust car to a battery powered scoop. It is several days after the accident and the mine superintendent assigns you and the safety supervisor to thoroughly investigate the accident to determine all the contributing factors. Your job is to make specific recommendations to prevent future slipping/tripping accidents.

Jan 10, 1999

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By Thomas K. Matson

The coal reserve base in the Western United States is presented for coalbeds amenable to extraction by underground mining methods. The Federal Bureau of Mines has abstracted data on the quality and quantity of coal resources/reserves from numerous State and Federal publications and modified such data as necessary to allow computer storage and retrieval. Tonnages are compiled by State, county, coalbed, and rank, and allotted to sulfur categories by statistical apportionment. The coal reserve base in those States west of the Mississippi River, amenable to underground mining, is estimated to be approximately 131 billion tons. Of this total, about 30.8 billion tons are bituminous coal, 100.2 billion tons are subbituminous coal, and 126.4 million tons are anthracite. Lignite is not considered for underground mining in this report. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves as jointly defined by the Bureau of Mines and U.S. Geological Survey. The purpose of this system is to provide for direct comparison or compilation of various resource/reserve data.

Jan 1, 1975

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978