Search Documents

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

Use water-jet-assisted cut-ting technology to reduce the exposure of mi ne workers' to respirable dust. Approach Install water-jet-assist on mining machines and evaluate its impact on respirable dust. How It Works Water-jet-assisted cutting involves a mechanical cutting bit working in combination with a moderate pressure (generally up to 10,000 psi) water jet directed just in front of, or through, the bit tip. One of its advantages is reduced dust generation because the jet wets the face of the material being cut more efficiently than a conventional low-pressure water spray, thus capturing much of the dust before it ever becomes airborne. It also removes loose cuttings ahead of the bit before they are pulverized by the bit into respirable dust. Total water consumption is about the same as for conventional low pressure dust control water spray systems. However, there is some increase in power consumption because of the energy needed to provide the high pressure water.

Jan 1, 1987

By Eugene Baker, Joseph Cervik, Albert Sainato

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the United States is limited to a few plow operations in the Pocahontas No. 3 Coalbed. This Bureau of Mines report describes the technology for infusing water in to a longwall panel and reports the results of a recent demonstration in the Lower Sunnyside Coalbed that achieved dust reductions averaging 58 pct. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 500 ft/min (2.5 m/s) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23-pct reduction in operating costs when coal production is increased by changing from unidirectional mining to bidirectional mining with water infusion.

Jan 1, 1983

By Staff

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975

By Maria I. De Rosa

For all coal mining categories, data on coal mine fires during 1990-1999 have been reported as actual numbers and calculated values. 1. For each mining category, actual numbers include the total number of fires, fire injuries, employees' working hours, lost workdays, and coal production (for underground and surface mines only) for a 1 0-year period (1 990- 1999) and for five successive 2-year periods with the 10-year period. These numbers have also been reported by state ( 10-year period). The actual number of fire fatalities has been reported by time period. Furthermore, actual numbers of fires for the five 2-year periods have been reported by ignition source, method of detection and suppression, equipment involved, location, and burning material. Actual numbers of fire injuries per number of fires causing injuries and total fires have been reported by year, ignition source, equipment involved, and location. 2. For each mining category, the calculated values include the fire and injury risk rates during the 10-year period and the five 2-year periods. The fire risk rate (Frr) values were calculated according to the USBM formula [Pornroy and Carigiet 19951. The injury risk rate (Irr) values were calculated according to the MSHA formula [MSHA 1991a, 1992, 1993, 1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001. Also, risk rate values for individual states (10-year period) were calculated according to the above-mentioned formulas. Of note is that only the risk rate values for the 10-year and five 2-year periods and risk rate values for individual states with the highest number of fires and fue injuries were considered for comparison purposes. The fatality risk rate values were not calculated because of the extremely small number of fire fatalities during the 1 0-year period. 3. Calculations of risk rate values are as follows: a. Fire risk rate (Frr) value: Number of fires per million tons of coal produced [Pornroy and Carigiet 19951. b. Injury risk rate (Irr) value: Number of fire injuries multiplied by 200,000 working hours per total employees' working hours [MSHA 1991a, l992,1993,1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001. The Irr value is the average risk rate value for the number of fire injuries per 200,000 working hours for a given time period.

Jan 1, 2004

By S. J. Hussey

A jig tailing with gold content ranging from 0.33 to 0.43 oz/ton was leached in weak cyanide solution with extractions of up to 97 pct in 24 hours. By countercurrent batch leaching studies and laboratory pilot plant operation, minus 10- plus 20-mesh and minus 6- plus 16-mesh coconut carbon were loaded to 700 oz/ton of Au. Minor silver in the ore reported in the carbon in amounts of up to 100 oz/ton. Gold adsorption rate data and an equilibrium adsorption curve for minus 10- plus 20-mesh carbon at ambient temperatures were developed and used in the successful application of a cascade design theory. The work was performed as a part of the overall Bureau of Mines research effort to help maintain an adequate domestic supply of metals by making improvements in mineral-processing technology.

Jan 1, 1979

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgica1 and" chemical methods to recover valuable constituents from metallurgical dusts and slags. Under this program a technique was developed to recover iron from molten copper smelting furnace slags by carbon injection. Slags from gas-fired reverberatory and electric copper smelting furnaces were treated in an 800-kva electric-arc furnace by injecting coke breeze into the bottom of the molten bath. Over 95 pct of the iron and over 90 pct of the copper contained in the smelting furnace slags were recovered, while up to 85 pct of the carbon injected into the system was utilized. It is anticipated that the metal product containing approximately 95 wt-pct iron and 2 wt-pct copper will be a satisfactory medium for recovering copper by cementation.

Jan 1, 1977

By Anthony T. Lannacchione, Donald G. Puglio

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 4 Hoist Assemblies (not man-rated) A large number of manufacturers supply materials handling winches. These units are predominately electric powered while a limited number of vendors supply air powered equipment. Air powered units are currently used extensively for underground materials handling purposes. Suppliers of materials handling equipment normally include a disclaimer statement in their published literature which clearly states that the equipment "is not designed or suitable for lifting or lowering persons " This category of commercially available equipment can be adequate for emergency man hoisting provided that its' capacity is suitably derated and provided also that the necessary safety features are incorporated. Section C. 5 details the equipment which could be added to a commercial materials hoist to meet these needs. Four commercially available hoist assemblies, two electric and two pneumatic are discussed in the following paragraphs. This equipment is typical of what is commercially available and three of the units are currently used extensively in mining applications. Each hoist description includes a remarks paragraph which identifies the additional equipment each hoist would require for emergency hoist use.

Jan 1, 1976

1. Mine drainage constitutes surface or ground water which flows from mines or mine sites and is usually characterized by concentrations of acidity or alkalinity. 2. The regional geology controlling the ground water flow pattern in conjunction with the life cycle mining plan can serve as a basis for making decisions about quality of water that can be expected to be encountered. 3. In regard to the prevention and control of acid water formation in underground coal mines, much is left undone in research and education: (A) Very little literature is available on this specific subject although much has been written on water management in underground mines. (B) Little or nothing is contained in the text books and curricula used in mining departments at colleges and universities with the result that educational offerings may be seriously deficient in these areas. 4. Prohibiting water entry into underground coal mines is the best method of preventing water pollution. Since this is not possible as mining operations are extended, preventing water or oxygen from contacting acid producing material may offer the next best alternative. 5. More emphasis is needed during the mine planning stage on steps to prevent water pollution. Such life cycle considerations as type of mining, sequence of development and spatial configuration as well as the elements of the drainage network and final network organization and extent must be considered.

Jan 1, 1970

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I1 describes an underground bituminous coal mine operating in a 72 inch seam, with an estimated production rate of 4,257,000 tons per year. The system includes 15 continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. The following section includes the input data sequence, annual cost report, and cash flow analysis "report for this data set.

Jan 1, 1975

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

By Rose L. Ballard

This chapter summarizes data on crude non fuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal non fuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production, The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1986

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The question as to whether or not the flow of water through pneumatic rock drills commonly used in this country keeps to a minimum dust disseminated into the air during drilling arose during a study of the dust-in-air conditions in Butte mines from February to July 1936 and December 1936 to June 1937 made by the Bureau of Mines in cooperation with the Anaconda Copper Mining Co., Butte, Mont, The purpose of this report is to describe the study, including some experimental work on the subject, and to give test results.ACKNOWLEDGMENTSThe help of the ventilation department of the Anaconda Copper Mining Co. in planning the study and collecting the data is gratefully acknowledged.EXPERIMENTAL CONDITIONSTests were conducted in an untimbered 6- by 8-foot crosscut in medium-hard granitic rock near the shaft station on an inactive level of one of the active Butte mines. Figure 1 shows the plan and section of the test location. Air was drawn from the shaft at the station, through the crosscut, and up through another shaft. The flow of air through the crosscut was decreased by a brattice downstream from the sampling location, so that relatively high, easily measurable dust concentrations would be obtained in the tests. Impinger samples for determing concentration of dust in the air were collected in an opening 51 inches wide, 29 inches high, and about 4o inches from the top of the rails in a wooden stopping about 16 feet downstream from the place where the test holes were drilled."

Apr 1, 1938

By Stephen C. Tadolini, Thomas M. Barczak

Western mines have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the early 1990’s provided a very effective alternative and remains the dominant form of tailgate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled together, provides more capacity than an equivalent sized Can support and improves transport efficiency. However, the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but they have not been proven in high deformation environments. Alternative supports are also being used in longwall recovery operations. These include the Rocprop and Omni Prop, which are extendable support systems. They also provide active roof loading which can be beneficial in these applications. Specialty supports, such as the Sand Prop and Spider Prop, have also been introduced into western longwall operations. This paper compares the performance characteristics of these various support systems.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

4. Preliminary Study - Remote Seal Checker 4.1 Introduction Determination of the completeness of each individual seal at the time of its emplacement is essential for an effective remote sealing system. A satisfactory seal checking technique should provide a signal which: (1) indicates percentage completion as the seal is emplaced (2) provides a definite indication of a complete seal (3) indicates the size of the unsealed area if a complete seal is not feasible This information is required to establish the need for additional seal material, the need for additional seals, and the risk likely involved in entering the mine., In many situations it is as important to know the quality of a seal as it is to build an effective one. It is likely that with repeated use the remote sealing technique developed by Foster-Miller Associates will be sufficiently reliable and predictable to preclude the seal checking requirement. It is recommended, however, that each seal be checked during construction to insure its completeness and increase the level of confidence so necessary in reopening the mine. 4.2 Description of General Problem Several characteristics of remote mine seals are important in considering techniques for evaluating the effectiveness of these seals. These include:

Jan 1, 1973

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947

Enhance coal mine worker safety and productivity by developing a means to control and predict coal mine mountain bumps. Approach The Bureau of Mines has been engaged in extensive research to understand coal mine mountain bumps and their effect on underground coal mining in the United States. Information was collected on the geologic conditions, mining techniques, and engineering parameters at five mountain-bump-prone mines. Although research has not yet evolved to the point where mountain bumps can be effectively predicted or controlled, such studies are invaluable for providing clues that can lead to the development of mountain bump mitigation technology. Case Study Results and Recommendations Mountain bumps in coal mines are explosions of the coalbed that violently release the strain energy stored within it into openings created by mining. Such an event is not only dangerous to mine workers, but can cause substantial amounts of damage to mine equipment, resulting in productivity loss and downtime. In a coal mine, the occurrence may cause coal to be expelled violently from the coal face or coal pillars or cause the mine floor to heave suddenly. Coal bumps are usually accompanied by a very loud noise and tremors or vibrations. Such ground failure:; usually occur in the vicinity of an active gob line in an active retreating room-and-pillar panel, or at or near the face in an advancing or retreating longwall mining panel.

Jan 1, 1989

By T. L. Joseph

"In the January 3 issue of Iron Trade Review, Sweetser2, in referring to the problem of coke combustibility, points out that, ""Someone should formulate a rule for the rate of flow of coke through the zone of coke combustion that now appears to be confined to a comparatively restricted volume in front of the tuyeres,"" In formulating such a rule it is necessary to distinguish clearly between combustibility, a property of the fuel, and rate of combustion, which is determined by the rate at which air is supplied to the fuel bed. The rate of carbon gasified at the tuyeres of a blast furnace is independent of coke combusti-bility. A fast-burning coke will burn in a more restricted volume than a slow-burning coke, but both types of fuel will be consumed at rates determined by the supply of oxygen,A number of the definitions of combustibility that have appeared in technical literature relate more closely to rate of combustion than to combustibility. Perrott and Kinney) have correctly defined it as follows: ""Combustibility of coke from the standpoint of its use in, the blast furnace is inversely proportional to the mean rate of gasification per unit volume of the combustion zone, assuming other factors remain constant,"" Combustibility of coke refers therefore to those properties that determine the size or extent of the combustion zone. Relative differences in these properties can be measured by the depth of the fuel bed required to convert oxygen from the air into carbon monoxide."

May 1, 1924