Search Documents

By L. A. Neumeier

Sound experimental ingots of zinc alloys for use as rolling slabs were cast with a specially constructed, semicontinuous casting machine. Nominal alloy compositions of Zn-1.0 percent Cu, Zn-0.12 and 0.36 percent Ti, and Zn-1.0 percent Cu-0.03 to 0.36 percent Ti were cast. This Bureau of Mines study was conducted to evaluate the suitability of the casting procedure for providing stock for rolling into sheet. Microscopic examination of ingot sections revealed structures in which grain size varied from the outer to center ingot zones. Columnar grains present in the center zone of the Zn-1.0 percent Cu ingot were absent in the titanium-containing ingots. The ingots with titanium displayed a finer grain size and eutectic structure in the center ingot zone than in the outer zone; the transition in grain size between the two zones was quite abrupt in some ingots. The overall grain size of the titanium-containing ingots was finer than that of alloys cast by more conventional methods. Chemical analysis revealed that compositional segregation is not a significant factor in the formation of the ingot structure. Microstructural studies of small ingots of similar alloys solidified at slow, fast, and intermediate rates confirmed that the ingot structure in the semicontinuous-cast ingots is related to cooling rate, which is, in turn, related to the particular casting machine design and the influx of cooling water on the withdrawing ingots. Microstructures of thin sheet hot-rolled from slabs of the semicontinuous-cast ingots demonstrated that the ingot structure does not preclude the rolling of sheet having a uniform microstructure. Results of hardness surveys of the semicontinuous-cast ingots demonstrated that copper and titanium exert essentially additive hardening effects in these cast alloys.

Jan 1, 1968

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By Ralph L. Windrow

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing methods and costs of mining and preparing sand and gravel for market at various plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The Clowdy plant, with which this paper deals, is located 7 miles west of Dallas, Tex., and has a rail connection with the Texas and Pacific Railway. In addition to the rail outlet there is a paved road over which materials produced at this plant can be moved into Dallas by truck.

Jan 1, 1932

By G. J. Conroy

Cable whip occurring during normal movement of a shuttle car can result in a personnel hazard and excessive tensions in the cable. This Bureau of Mines report discusses preferred payout and reel-in torque settings to reduce cable whip. A simplified adjustment procedure is described.

Jan 1, 1974

Lower the respirable dust exposure of longwall shearer operators by use of a modified head to tail cutting sequence. Approach Modify the cutting sequence of double-drum shearer operations cutting unidirectionally head to tail, so that the tailgate drum is used to mine the entire coal face except when cutting out at the head. This approach would place the primary dust generating source, the cutting action of the drum, on the return air side of both shearer operators. How It Works Currently, 75% of the double-drum shearers in operation employ a unidirectional cutting sequence. On half of these operations, the primary cut is taken as the shearer travels from the headgate to tailgate ends of the face, with roof support to be advanced on the intake air side of the shearer. Typically, the leading (tailgate) drum is taking a full cut during the head to tail pass and the trailing (headgate) drum is cutting bottom coal. In this mode of operation, the dust generated by the trailing (headgate) drum can spread out into the walkway, and increase the respirable dust exposure of both head and taildrum operators. As an alternative, if the trailing drum is "free wheeling" or cutting minimal coal during the head to tail cut, and bottom coal taken by the tailgate drum during the tail to head clean-up pass, both operators are able to work on the intake air side of the primary dust generating source (drum) except when cutting out at the head. This modified cutting sequence would save wear on the conveyor and help to eliminate overloads, as well as reduce the respirable dust exposure of both shearer operators. This modifcation is only applicable to long-wail operations currently cutting unidirectional head to tail, and to those operations where this unidirectional cut would not produce operating constraints.

Jan 1, 1981

By Robert S. Sanford

The Broughton and Ring magnetite deposits in Essex County, N. Y., are thought to be in a mineralized belt that extends from the Lake Sanford mining district to Lake Champlain and passes through the Mineville district. The country rook is syenite-gneiss, similar to that in the Mineville area. The Bureau of Mines conducted a vertical magnetometer survey of the area. On the Broughton properties there are no indications, magnetically, of magnetite in any degree of concentration. 'On the ding properties a number of sharp, localized magnetic anomalies were observed. One core-drill hole was bored to a, depth of 48.3 feet, also, to test one of the strongest anomalies. The field work was in progress from December 1943 to July 1944. Although no iron ore was intersected by' the drill hole, it showed that the amphibolite rook, at a depth of 6 to 100 feet below the surface, contained enough magnetite and iron sulfides to account for the anomalies recorded by the magnetometer survey.

Jan 1, 1949

By D. Harrington

"Since its establishment in 1910 the Bureau of Mines has consistently recommended the rock-dusting of bituminous and lignitic coal mines as a preventive of widespread explosions. As with many other proposed innovations, the response to the bureau's recommendation has been slow; but during the past 10 years many coal mines have done some rock-dusting, even though probably fewer than 50 of the country's approximately 6,000 coal mines are thoroughly rock-dusted. Notwithstanding the inadequacy of the rock-dusting which has been done in most of the mines which have adopted the new system, numerous cases are at hand. indicating the well-founded basis of the bureau's claims regarding the effectiveness of rock-dust in stopping explosions. Very brief descriptions will be given of several cases in which explosions in coal mines of the United States are fairly definitely known to have been stopped by rock-dust during the past 5 or 6 years; in addition, several cases are cited in which explosions were stopped through the agency of rock-dust and moisture.A rock-dusted mine is one in which the floor, roof, and sides of every accessible working place, including haulage ways, airways, manways, and rooms and connections have an application of rock-dust - for instance, limestone - such that the incombustible content of the aggregate dust on those surfaces is over 60 per cent. The dust in these workings should be sampled at regular intervals to determine whether the incombustible matter in the coal-dust is less than the necessary minimum of 60 per cent; another application of rock-dust should be given when the incombustible percentage is less than 60. (As an example of thorough rock-dusting, see Bureau of Mines Information Circular 6578, 1932, which describes how rock-dusting is done in Alabama at a cost of 1.8 cents per ton of coal for a thorough application; Report of Investigations 3060, February, 1931, Rock-Dusting In A Pennsylvania Coal Mine; or Information Circular 6244, 1930, giving data, including costs, on rock-dusting in coal mines in New Mexico.)An explosion may be started by the ignition of gas, even when rock-dust is present; hence it is not correct to say that rock-dust will prevent an explosion of gas; however, if rock-dust has been applied to a working place which has present an explosive mixture of me-thane and air, and if an open light is used or a blown-out shot or an electric arc occurs, although there will very likely be an ignition and possibly an explosion, the rock-dust will certainly prevent ignition of the coal-dust nearby, and unless the general atmosphere has an explosive gas mixture, the rock-dust will stop propagation of the flame throughout the mine. In other words, if an explosion is started by gas or by coal-dust and the mine has been rock-dusted as defined, the rock-dust will prevent widespread extension of the explosion, unless the general atmosphere contains methane and air in explosive proportions.With these definitions clearly in mind, instances are now given where rock-dust has played a prominent part in the stopping of several explosions. No cases have been included where there was any reasonable doubt that rock-dust had taken a definite part in the limiting of the explosions."

Apr 1, 1932

By Rudolf Kudlich

"During the coming winter, it is probable that many householders who have habitually been users of anthracite coal will be obliged to turn to some other fuel for heating purposes, because of the limited supply of anthracite. The next best fuel, from a standpoint of cleanliness and ease of operation, is coke, but here again the supply is inadequate and the householder will have to fall back on bituminous coal. Though bituminous coal has the dis¬advantage of being dirty to handle, requiring more care in firing, and of giving off considerable smoke, it will be more generally available, costs less, and in the better grades which will naturally find their way to the domestic market, is higher in heat value, and contains less ash than anthracite.Choice of CoalThere a variety of bituminous coals are available, the householder should choose a low volatile coal, such as New River, Pocahontas, or some other ""smokeless"" coal, or the British coal now being offered in the markets along the Atlantic seaboard. Though not necessary to have the coal sized, as is the case with anthracite, it will be found cleaner to use coal from which the fine dirt has been screened. If it is found that excessive dust is caused when firing the coal, this can be reduced by slightly wetting the coal at the front of the bin, as it is being used.Method of Firingusing bituminous coal instead of anthracite in the domestic furnace, it will be necessary to use an entirely different method of fir Instead of leveling the fuel bed and putting on fresh coal in an even layer over the entire fire box, the coked and partly burned coal remaining from the previous firing should be pushed as much as possible to one side of the box, and the fresh coal thrown into the empty side so as to leave some burning coal exposed. In this way the green coal is heated slowly, the volatile gases are given off gradually, and are ignited by the burninggoing to waste up the chimney unburned."

Oct 1, 1922

By John L. Ellenberger

The Bureau of Mines investigated the occurrence of slickensides in mine roof in the Pittsburgh coalbed in a portion of the Valley Camp No.3 mine in southwestern Pennsylvania to improve the potential for prediction of slicken-sided zones and determine the orientations of the most prominent slickensided planes. Two distinct types of slickensides were identified; those which were associated with clay veins observed in the coalbed (genetic), and those which were unrelated to any visible structure (nongenetic). The study draws three conclusions: (1) Nongenetic slickensides are not the result of tectonic forces, (2) both genetic and nongenetic slickensides tend to dip at an angle of 30°, and (3) genetic slickensides tend to be alined parallel to the trend of the clay vein and usually dip toward the center of the clay vein. A schematic roof bolting plan is presented that may provide improved roof support where slickensides are present. Roof stability could be improved by supplemental bolting in the direction normal to the plane of slickensides.

Jan 1, 1979

By J. B. Janus

This report continues a series of analyses of coal samples made by the Bureau of Mines in connection with the yearly purchase of several million tons of coal for various Government agencies. Listed are the analytical data on the composition and quality of tipple and de livered samples of coal collected during fiscal year 1974.

Jan 1, 1975

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993

By Oleg Terichow

The Bureau of Mines studied the penetration of a slender cylindrical tube into a sand bed, simulating seafloor material under the application of a static load. The factorial experimental design was based on three factors: tube diameter, geometry of penetrating bit, and seawater saturation of sand, all of which were found to be significant in influencing the depth of penetration. The geometry of the penetrating bit, or shoe, is of major significance in the mechanics of penetration and should be considered the most important factor for additional study. Linear regression analyses of the load-penetration data show that the relationship is linear.

Jan 1, 1970

In December's marketing of 99.5 percent aluminum ingot, domestic producer pricing remained at 53$ per pound, while dealer quoting rose from 47.5¢ to 48.5¢. BORON Domestic production of boron minerals and chemicals reached an all-time high in 1977--1.4 million short tons valued at $236 million. Combined sales of the three California producers topped the 1976 level by 15 percent in quantity and 28 percent in value, a consequence of healthy demand in the glass and insulation industries. Unprecedented demand for boric acid as a flame retardant for cellulosic insulation stimulated producers to utilize fully all available capacity, thereby achieving a record output of 158,000 tons. One company increased output from its existing boric acid facilities and initiated production at another plant that historically had produced only sodium borates. A second company achieved a previously planned 25 percent plant expansion.

Jan 1, 1978

By E. G. King

Cerium and thorium sulfides have found use as crucible materials for melting certain radioactive metals. However, thermodynamic treatment of these sulfides has been hampered by lack of experimentally derived entropy values. This Bureau of Mines report describes heat-capacity measurements between 51° and 298° K, and entropy evaluations at 298.15° K, for cerium monosulfide (CeS), cerium sesquisulfide (Ce2S3), and thorium disulfide (THS2). The entropy values, with Literature results for the heats of formation, are used to obtain free energies of formation at 298.15°K. MATERIALS The samples used in this work were supplied by Prof, Leo Brewer of the Department of Chemistry, University of California. The methods of preparation and some of the physical and chemical properties of these sulfides were given by Eastman and coworkers.3 4/ Chemical analyses, conducted in our laboratory, gave the following results:

Jan 1, 1959

By Larmon J. Heath

The Bureau of Mines explored the use of air or natural gas for recovering additional oil from natural water-drive reservoirs with little or no original gas saturation. Engineering and production data for a field in the Mid-Continent area, results of limited laboratory experiments, and data shown in the literature were considered. Injecting air into a water-coned well could seriously damage the well. Injecting natural gas into the watered-out zone could improve the producing water-oil ratio. In the reservoir studied, oil recovery can be increased by injecting natural gas to decrease water-oil ratios. Laboratory tests on a core from the field show an increase in oil recovery of 7.6 percent of the original oil in place as a result of increasing the free gas saturation. This recovery could amount to as much as an additional 6 million barrels of oil from this field.

Jan 1, 1966

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By Lloyd A. Morley, Alan M. Christman

Introduction A wealth of information exists which deals with electrical grounding, both from a general viewpoint and from a specifically mine-oriented approach. Many parameters must be investigated in order to thoroughly cover all of the variables which govern the performance of electrical grounding systems. The emphasis of this work on open-pit practices re- presents a new development in the field of grounding research, and an exhaustive review of the relevant historical documentation is especially desirable. Grounding System Purposes What purposes are served by a grounding system? The answer is four-fold and may be summarized as follows. First, it must limit potential gradients between conducting materials in a given area (56). When a phase conductor comes into contact with a machine frame, current flows through the equipment, which tends to become elevated above ground by an amount equal to the voltage on the conductor. If a man were to touch the machine while he was simultaneously connected to ground in some manner, his body would also tend to become elevated in potential, possibly to a lethal extent. Thus, the grounding system should provide a low- resistance path for the fault current to return to the source. The maxi- mum potential to which a man could be exposed when touching a machine frame is equal to the voltage drop along the ground conductors inside the power cable, as shown in Figure 1 (54). The ground conductors, therefore, (page # 96 is missing from the original document)

Jan 1, 1976

By E. G. King, W. W. Weller

Low- temperature heat capacity measurements of muscovite were made in the temperature range from 50° to 298 ° K. The entropy at 298.15 ° K was evaluated as S298.15 = 69.0 ± 0.7 cal /deg mole .

Jul 1, 1960

Louisiana's coal reserves, located in the north-western part of the state, consist entirely of lignite, with estimated recoverable reserves of about a billion tons. Although lignite deposits were discovered in the early 1800s, the first documented use of lignite occurred at the federal arsenal near Shreveport during the Civil War. By the late 1800s, lignite use was common by blacksmiths, railroads, and steamboats. Lignite production ceased, however, from the early 1900s until 1985. A new lignite mine permitted September 1, 1985, produced 0.2 million tons in its first year. The operation uses a seven-mile-long conveyor to transport lignite to the associated mine-mouth power plant. The surface coal mining reclamation and enforcement program in Louisiana was approved October 10,1980. Louisiana's Abandoned Mine Reclamation Plan was approved December 10, 1986

Jan 1, 1992

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009