Search Documents

Studies on coal mine drainage sludge densification have led to the following conclusions: 1. Coal mine waters containing iron principally in the ferrous (Fea+) state can be treated by a modification of the commonly practiced lime neutralization process to yield a ferromagnetic sludge. The sludge, presumably composed in large part of a hydrated ferrosoferric oxide (Fe304.xH20), is much denser and faster settling than the ordinary "yellowboy" sludge obtained by lime neutralization and aeration at ambient temperatures. 2. The magnetic sludge preparation technique involves (quantitative) precipitation of iron (largely as Fe(OH)2) by the addition of hydrated lime to a pH of 8.5, separation of the resulting sludge from the aqueous phase, and heating of the sludge concentrate to at least 80 C (176 F), preferably higher, followed by mild aeration. 3. Magnesium, present as Mg2 in most coal mine drainage waters, inhibits the formation of the magnetic sludge. This inhibition can be adequately minimized by keeping the pH below 9.6 during lime addition (thus avoiding the coprecipitation of Mg(OH)2) and by separating the sludge from the bulk of the aqueous phase before the heating step, as indicated in (2) above. 4. Aluminum, commonly present in coal mine drainage waters, also inhibits the formation of the magnetic sludge. This inhibition is of practical significance when the molar ratio of aluminum/total iron is greater than 0.18. Below this value, sludges are still appreciably magnetic, but are bulkier and slower settling than those obtained when aluminum is absent. Unlike magnesium inhibition, aluminum inhibition cannot be minimized by the scheme indicated above, since aluminum precipitates as Al(OH)3 near pH 4 and remains dispersed within the sludge. 5. The limitation on aluminum content is probably the most serious restriction affecting the feasibility of the magnetic sludge process as presently conceived. Nevertheless, a limited review of available water quality data has indicated that, in terms of relative acid and iron loadings, a significant number of major coal mine discharges in the eastern Ohio River basin may be amenable to treatment by a magnetic sludge process. 6. Data from tests on the use of magnetic seeding materials indicate that seeding did not enhance the formation of a magnetic sludge under the experimental conditions employed.

Jan 1, 1971

By Oliver Bowles

"Introduction.During recent months the Bureau of Mines has conducted a detailed study of the slate industry with special reference to increased efficiency in its production, preparation and utilization. The results of these investigations will be incorporated in a forthcoming bulletin. The purpose of this preliminary paper is three-fold. One object is to bring to the attention of slate producers certain modifications in manufacture and classification which would encourage a wider use of slate. A second purpose is to direct the thought of roofers toward the importance of proper laying of slate, and the third object is to acquaint the general public with its enduring qualities.Origin and character.Without entering into any detailed discussion of the origin and history of slate, a subject to be covered in the bulletin mentioned, it may be of interest to the general reader to know that slate is originally formed from mud or soft clay, carried down by streams and laid down in successive layers in deep water. The pressure of superimposed materials gradually compresses the clay into a firm rock known as shale. In many places this shale was, during the succeeding ages, subjected to intense pressure and folding due to mountain-building forces within the earth. This intense pressure, together with high temperature, changed the clay into other minerals such as mica, chlorite, and silica, which are very resistant to weathering, and also developed a very definite cleavage or splitting direction which characterizes the rock as slate. It is this property which renders slate of value for roofing, for, by using a broad chisel and a wooden mallet, a slate worker can readily split it into thin sheets which are later trimmed into rectangles of various sizes."

Jul 1, 1921

By Giorgio Franceschetti

Explicit expressions are presented for the input admittance and effective height of several buried metal antennas, namely: (i) prolate spheroidal; (ii) spherical; (iii) oblate spheroidal; (iv) parallel plate; (v) parallel plate with protruding dielectric in the same plane of the plates; (vi) parallel plate with protruding dielectric in a plane normal to that of the plates (H-shaped antenna). Explicit expressions are presented for the input admittance and effective height of several buried metal antennas, namely: (i) prolate spheroidal; (ii) spherical; (iii) oblate spheroidal; (iv) parallel plate; (v) parallel plate with protruding dielectric in the same plane of the plates; (vi) parallel plate with protruding dielectric in a plane normal to that of the plates (H-shaped antenna). It is concluded that in all practical situations of "small" antennas approximation 1 is almost always appropriate. Computations were carried out for bare antennas, the extension to insulated ones being, however, straightforward. Although a rigorous theory of the antenna performance in a realistic semi-infinite conductive medium has not been developed, the results quoted should also be applicable when antennas are a few skin depths below the earth's surface. In particular, for the evaluation of radio-links under up-over -and-down operating conditions, the antennas can be replaced by dipoles of length equal to the effective height. Since the antenna's parameters are given in analytical form, it is also possible, by using Laplace transform techniques, to compute the transient response of the antenna. The transient is described by pole (short-time behavior) and branch-cut contributions (large time behavior). For these last terms, an asymptotic evaluation is possible, so obtaining closed form expressions for the response at large observation times, which is closely related to the dispersion characteristic of the environment.

Jan 1, 1973

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to melt residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-offgas handling system, and thermal oxidizer for final offgas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 lb/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kV?A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the offgas and serves as an acid gas scrubber. The clean offgas is heated to 1,800° F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 2010

By W. N. Cathey

Many materials including carbides, silicides, phosphides, borides, nitrides, oxides, and metals were studied by the Bureau of Mines as potential fuel cell catalysts for electroreduction of oxygen in a 1[N]H2S04 electrolyte. The objective of this study was to assess the potential of abundant, low-cost materials as substitutes for platinum or to increase the catalytic efficiency of platinum. Several compounds were rejected because of their reaction in the corrosive environment of the oxygen electrode. However, some of the remaining were the most active catalysts. Activity of carbides such as tungsten carbide could be improved by doping with platinum-group metals, by varying stoichiometry, or by sputtering on a layer of platinum. While no catalysts were found with activity as high as platinum, some compounds were shown to be deserving of further investigation.

Jan 1, 1979

By W. M. Weigel

"Sand is one of the commonest materials for industrial use, not only as a building material, but in many industrial processes. The general name applies to all grades, from the comparatively impure, unsorted product used in concrete, to especially sized products of extreme chemical purity. Various definitions have been proposed, all more or less open to objection, as they fail to cover special applications. One is: ""Sand - The fine granular material naturally or artificially produced by the disintegration or crushing of rock or slag"". This does not fit the definition of sand as understood by geologists, who consider sand only as a naturally formed product. Another is: ""Sand - The fine granular material naturally produced by the disintegration of rock"". This does not take the chemical com-position into account, and for practically all uses, except in concrete and plaster products, a material composed predominantly of silica or rather quarts is implied.Sand for special purposes usually requires different methods of preparation from those where the ordinary mixture of sizes as naturally occurring are suitable. One of the classes requiring the most uniformly sized grains is sand blast sand.Sand Blast SandThe use of the sand blast has increased rapidly during the past few years. It was formerly used almost entirely in the foundry to clean and remove inequalities from rough castings. This is still the most important application, but in addition, it is now employed for the removal of paint from old surfaces, carving and engraving on stone and marble, glass cutting, cleaning or renovating the rails of stone and brick buildings that have become discolored, preparing the surface of metals for the electrolytic bath, putting the final finish to metal surfaces, and has even been proposed as a means of channeling or cutting out blocks of stone in the quarry."

Jun 1, 1924

By E. C. Tarpley

The Federal Bureau of Mines has studied solvent extraction as a means of concentrating the mineral components in coal. Solubilities of a number of American coals were determined using abietic acid as a solvent. The effect of rank on solubility was investigated, and maximum solubility was found with coals of intermediate rank. Vitrinite is the most soluble petrographic component; fusinite, micrinitc, and exinite are nearly insoluble. Spore exines also have a low solubility. Abietic acid is a hydrogen donor and reduces pyrite to ferrous sulfide. Mild hydrogenation of high-molecular-weight fragments of the coal structure to those of lower molecular-weight probably contributes to the solvent action. Even where solubility of the coal substance exceeds 90 percent, contamination of the mineral matter with coal makes identification of the mineral components difficult. Further separation might be possible by the application of float and sink techniques to the residue. INTRODUCTION Work n the solvent extraction of coal is conducted to recover commercially useful products and to characterize coal;. and obtain information on their structure. Some coals, particularly those of low rank, contain waxes, resins, and humic acids which can be removed by solvent extraction and find varied industrial uses. In World War II, solvent extraction of coal was conducted on a commercial scale in Germany to obtain a low-ash feed material for hydrogenation and to produce electrodes carbon for the aluminum industry.4 5/

Jan 1, 1960

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

This report was prepared by The Pennsylvania State University under USBM Contract No. H0133040. The contract was initiated under the technical direction of PMSRC, with Mr. Edward D. Thimons acting as the technical project officer. Mr. Frank Naughton was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June 30, 1973,to June 30, 1977. This report was submitted by the authors on August 31, 1977.

Jan 1, 1977

By Samuel B. Flagg

The Bureau of Mines is endeavoring to ascertain how mineral fuels in which the Government has a direct interest, by ownership or use, can be utilized with highest efficiency. For this reason the bureau has been, and is, carrying on investigations to ascertain the condi- tions of furnace construction and management that are necessary to insure the smokeless combustion of the different coals that are found in public lands or are purchased for Government ships and power plants. Another reason for the bureau undertaking these investigations is the need of better furnace management and a more careful selec- tion of fuel at many Government plants. There are Federal build- ings in hundreds of cities. The coals available at many of these cities differ greatly in quality, and the furnaces in some of the Fed- eral buildings were not designed for efficient utilization of the cheap- est available coal. Hence, some of the boiler plants smoke badly unless fed with low-volatile coal and have caused repeated com- plaints not only from neighboring property owners who have suffered damage, but from persons endeavoring to create a civic pride in clear air. In the course of its fuel investigations the bureau has noted the conditions governing fuel consumption in different cities and has studied the attempts made by these cities to abate smoke through the passage of ordinances imposing penalties on smoky stacks. Some results of that study are presented in this report. The most im- portant conclusion reached is that smoke abatement by ordinance can not hope to succeed unless supported by public sentiment and that a smoke ordinance should look to future prevention rather than to immediate prohibition. In other words, strict control of furnace construction offers much greater hope for smoke abatement than desultory imposition of severe penalties on the escape of "dense" or "black" smoke.

Jan 1, 1912

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Colombia has been prepared from the best available information in Washington, but is released subject to correction and amplification; if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW Minerals in Colombia belong to the owner of the soil unless otherwise provided in the law. The following lands and deposits, however, are described as fiscal property of the State: Class 1. The public lands, mines, and salines which belong to the individual States (now Departments) prier to the adoption of the present constitution (1886).

Jan 1, 1929

By F. M. Boler

The U.S. Bureau of Mines has configured a flexible data acquisition and analysis workstation, which incorporates control and analysis software written in-house for use in mining research experiments conducted in the laboratory and in operating underground mines. This data acquisition system combines computer-automated-measurement-and-control (CAMAC) modular instrumentation with a Unix-based graphics workstation. The data acquisition front-end hardware can be interfaced to almost any computer. CAMAC instrumentation modules adhere to mechanical, electrical, and digital interface standards and can be custom designed or purchased off the shelf. Communications along the CAMAC bus are regulated by the crate-controller module, which contains the only hardware link to the computer interface. Software support for the data acquisition and analysis workstation consists of a series of functions and programs written in the "C" programming language designed to provide flexible and fast data acquisition, processing, and analysis. The user can interactively control the digitizers and other CAMAC modules by sending standard CAMAC read, write, and command function codes from a menu-driven program. Automated data collection is achieved through software that responds to hardware interrupts triggered by acoustic emission or microseismic events. Graphics display routines are used to plot part or all of the data and provide the ability to process and store signal information selectively.

Jan 1, 1990

By T. J. Ballard, Austin B. Clayton

"INTRODUCTION The Conrad Hill mine was first opened as a gold mine about 1832 and has been operated at various times since then.The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings.The: work failed to reveal appreciable copper values or evidence of additional ore deposits.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The field work embodied in this report was under the direction of Austin B. Clayton. The final report was prepared by T. J. Ballard uncle,- the general supervision of Mitchell H. Kline, chief, Raleigh, N. C., Branch, Mining Division. Analyses of samples and beneficiation tests were made by the Metallurgical Division. ACCESS AND OWNERSHIPThe property is 6 miles southeast of Lexington, N. C., and can be reached by U. S. Highway 64, turning off at Hedrick Grove Church, and is 1 mile north from the highway on the county road. The mine is in Davidson County at approximately 35° 47' latitude and 80° 10' longitude (fig. 1).The property comprises 471 acres and is owned (1943) by the McKeeMining Co., 512 Fifth Avenue, New York City. The property was optioned to Woodrow McKay of Lexington, N. C., in 1943, who in turn subleased the property to the Robert G. Lassiter interests of Raleigh, N. C."

May 1, 1948

By S. P. Kinney, P. H. Royster, T. L. Joseph

An investigation of the production of iron in the blast furnace is obviously not an easy subject for research . Enough is known of the mechanical , thermal and chemical conditions existing inside the furnace to say certainly that they are complicated. Furnace operators have found that the process is sensitive to a number of known and to many unknown operating conditions . In order to form any conclusions of value , it seems necessary to collect a large amount of data taken with considerable care and accuracy. These facts make a blast furnace research difficult but not impossible . The most serious obstacle in attacking the problem comes from the fact that it is useless in the design and operation of the blast furnace to use the method of " trial and error , which has proved valuable in so many other industrial problems . The variables are so interrelated and are so dependent one on the other that the number of experimental combinations to be tried is enormous . There are certainly not less than twenty factors in furnace operation and design that are known to influence the results . This is apparent if it is remembered that a phrase like " size and shape of the furnace" includes height of the furnace , height , diameter and angle of the bosh , inwall batter , stockline diameter , and furnace volume ; and that a phrase like " chemical and physical properties of the fuels charged " includes size and shape of the lumps , density, porosity and strength of the coke , in addition to its chemical analysis . Let us suppose that we need choose for each of twenty factors one of two values , for example , suppose we must say only that the furnace shall be " tall " or " short , " that the bosh angle shall be " flat " OF "steep , that the ore shall be " coarse " or " fine , " or that the blast has to be "hot" or " cold , " the number of resulting combinations is more than one million . In putting twenty pennies on the table , either heads up or tails up, the number of permutations possible is the twentieth power of two , slightly more than one million. It is obvious , therefore , that some sort of mathematical relationship , a set of rules of thumb , laws , curves or the like , are needed . Whether the relationships , curves or formulas are derived from experiment , from theory, or from mere guess -work, makes no difference provided they agree with the known facts . If they do not agree with known facts , they are worthless no matter what their origin or how weighty the " authority" vouching for them. Few such relationships have appeared in blast- furnace literature , and it may be doubted whether such formulas can be discovered .

Sep 1, 1923

By H. J. Heinen

This report summarizes preliminary research studies by the Bureau of Mines in electrowinning molybdenum directly from pure or impure molybdenum trioxide (MoO3) by fused-bath electrolysis in an open graphite cell without need of a protective inert atmosphere. A formulated electrolyte of the tertiary system containing 41.6 percent sodium pyrophosphate, 16.7 percent sodium tetraborat, 33.3 percent sodium chloride, and 8,4 percent molybdenum trioxide, by weight, electrolyzed at 1,000° C,, gave excellent results. Current density studies were made over a range from 20 to 260 amperes per square decimeter. Current efficiencies of 80 to 90 percent were obtained over the entire range. Yields up to 500 grams of molybdenum per kilowatt-hour were obtained. Higher current densities, however, reduced yields and produced a finer grained metal. The two most important facets in electrowinning molybdenum from MoO3, in an open cell, are temperature and electrode spacing to minimize or eliminate the formation of the suboxide MoO2, the major source of oxygen contamination. At temperatures of 1,000° C. and higher, together with the proper spacing of the electrodes, formation of oxides are practically eliminated. Molybdenum metal electrowon from pure MoO3 was 99.9 percent pure and contained 0,056 percent oxygen and 0,007 percent carbon. This metal, when arc-melted, had a Vickers hardness number of 175 and contained 50 parts per million oxygen and less than 10 parts per million carbon. Molybdenum metal electrowon directly from an impure MoO3 containing 90 percent MoO3 resulted in a metal of 99.8 percent purity.

Jan 1, 1961

By Bernard Porter

The rate of the heterogeneous reaction between reactor-grade yttrium and lithium fluoride in lithium fluoride-yttrium fluoride mixtures was measured using a quartz spring balance. At 950° C the magnitude of the rate of reaction is 10-5 grams of yttrium/cm2-sec. The heat of activation for the reaction is 38.3 kilocalories per mole of LiF. A surface-controlled mechanism is proposed in which LiF is adsorbed on the yttrium metal surface. An activated complex is formed when additional LiF reacts with the adsorbed LiF-metal site. The activated complex then decomposes to the products) which are lithium metal and YF3. The importance of the reaction in the electrowinning of yttrium metal from fluoride electrolytes is discussed.

Jan 1, 1967

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979