Search Documents

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By Ernesto Villaescusa, Andres Brzovic

Rock masses of the primary copper ore at the El Teniente Mine are very competent and massive. The rock mass contains almost no open discontinuities. Nevertheless, there is a high frequency network of small discontinuities coupled with widely spaced faults. A data collection campaign designed to characterize the rock structure was recently implemented. The results show that conventional analysis in terms of discontinuity frequency does not predict differences between two studied sectors. However, when an empirical definition of a weak discontinuity is applied, appreciable differences between the two sectors appear in terms of discontinuity frequency and predicted in situ block size distributions. These differences are in accordance with actual observations at the mine site. Due to the geological features of the primary copper ore, rock mass classification schemes cannot be readily applied to characterize these rock masses.

Jan 5, 2007

By H. D. Jacobs

The Bureau of Mines developed a concentration method to upgrade and utilize marginal natural or direct-shipping iron ores and fine-grained lean iron ores. Presently these ores receive little beneficiation and accordingly have low iron-silica (Fe-Si02) ratios. Ore samples were roasted with equal weights of solid reductant at 1,100° C for 1 hour to metallize the iron and for an additional hour at 1,200° C to promote grain growth. Concentration was effected by crushing and screening techniques and/or wet magnetic separation. Sized concentrates (minus 4 plus 35 mesh) derived from crushing-screening processes contained from 80 to 85 percent iron that was 90 percent metallized. Iron-silica ratios as high as 12:1 and iron recoveries from 75 to 94 percent were obtained. The sized concentrates were judged suitable for use as blast furnace feed. Minus 200-mesh metallized concentrates derived from roasted minus I-inch plus 8-mesh ore fractions and magnetically concentrated contained 90 percent Fe and 4 percent or less Si02, chemically qualifying them as feed for electric furnaces. Roasting minus 8-mesh ore with hydrogen, then magnetically concentrating it, produced iron concentrates containing 57 percent to 67 percent Fe and 3.6 percent to 8.4 percent Si02. The concentrates having Fe-Si02 ratios ranging from 8:1 to 12:1 were considered adequate for use as blast furnace feed. Overall iron recoveries for the 12 ores tested ranged from 56 percent to 94 percent with an average iron recovery of 86 percent.

Jan 1, 1969

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By J. G. Donaldson

The Bureau of Mines investigated the formation of boron and boron-carbide coatings by vapor-phase reactions. Optimum parameters were determined for hydrogen reduction of boron trichloride and for the fonnation of boron-carbide coatings on graphite by reaction with the depositing boron. At 1,300° C, about 85 percent of the boron was deposited. Tungsten substrates did not react with the boron deposit; other substrates reacted to various extents. The hydrogen reduction of boron tribromide was briefly investigated. Boron carbide was deposited at 1,300° C by adding methane to the boron trichloride-hydrogen feed gas. The chemical composition of the vapor-deposited boron carbide approximated B4C. A method of etching B4C was developed to study its microstructure. When boron was deposited on graphite at 1,500° C, very hard, uniform, strongly adherent coatings of B4C were formed that might be useful in rocket nozzle applications.

Jan 1, 1968

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau's engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By K. K. Kershner

This report describes an investigation by the Bureau of Mines designed to provide background data for extending and improving the applications of chlorine metallurgy in extracting metals from ores. Optimum conditions are given tor chloridizing galena, sphalerite, and chalcocite by contact with chlorine gas. Petrographic and chemical analyses of the sulfides used in the experiments are listed. Graphs are furnished showing the extent of chloridization of each metal sulfide over the temperature range of the observations. In each case, the first tests were made with the reaction chamber at room temperature. This temperature was increased by regular increments in succeeding tests until the temperature was reached at which quantitative conversion of the sulfide to chloride was observed. The data are also plotted for screen-size fractions of the sulfide minerals investigated. Data show that the extent of metal chloride formation was affected by chloridization time, particle size of the sample, and usually, the temperature of the reaction chamber. At 300° to 400° C. an anomaly was noted for both galena and sphalerite. The temperature at which this anomaly was observed varied according to the particle size of the mineral. Comparisons are made between the chloridizing characteristics of the mineral sulfides and their chemically prepared counterparts.

Jan 1, 1961

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50.

Jan 1, 2000

By Thomas E. Popplewell

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing the mining and treatment methods and costs obtained in sand and gravel plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners' training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry (Morbidity and Mortality Week Report, 2001; NIOSH, 2002). Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year (NIOSH, 1999). Mine safety and health professionals have long recognized training as a critical element of an effective safety and health program. Federal regulations (30 CFR, Parts 46 and 48) require mine operators to provide initial safety and health training to all new miners, as well as a minimum of 8 hours of refresher training each year. The time and money being spent to train U.S. miners is substantial, and so there is a strong and steady demand for new and better mine training materials and methods. A growing concern among mine safety professionals regards the training of new workers. A major change in the mining workforce is anticipated within the next decade. In major segments of mining, especially coal, relatively few workers have been hired since the 1970's. Thus, as an entire cohort of miners in the current workforce nears retirement, the replacement of these employees will require an influx of new workers. New miners may be young people who lack the ability to recognize and respond to mining hazards in an appropriate manner. They may also have had different educational experiences than their older counterparts. Many safety professionals believe that these two cohorts require different approaches to training. The papers in this report should help prepare mine trainers for the changes about to occur in the workforce and acquaint them with strategies they can use to enhance the effectiveness of their training. The first three papers present basic principles for teaching adults. The five remaining papers are intended to illustrate how these principles can be applied to the development and imple¬mentation of effective training for miners. Below is an overview of these papers. 1. Kowalski and Vaught review the process and principles of adult learning. The learning model they present includes a discussion of goals, content, delivery, assessment, and remediation. Adults are viewed as active learners, experienced-based, expert in their own right in specific areas, independent, real-life centered, task-centered, problem-centered, solution-driven, skill-seeking, self-directing, and internally and externally motivated. Basic aspects of curriculum development are briefly reviewed. For further information about adult learning, see Camm and Cullen's paper. 2. Mallett and Reinke's first paper discusses issues related to training new miners who have recently or will soon be entering the mining workforce. These new generations of miners have different learning style preferences and training needs than Baby Boomers and other older miners. Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these young new workers. This paper provides information that will help mine trainers communicate across the generation gap. 3. Mallett and Reinke's second paper provide an overview of training evaluation. Trainers and decision-makers are given a framework for planning and assessing training evaluation strategies. The authors present Kirkpatrick's (2001) model of evaluation categories and discuss how to start an evaluation plan and various ways to collect data. They do not provide detailed instruction in evaluation methodologies, but give trainers a review of the things they need to consider when developing an evaluation plan. A good evaluation plan can inform revisions to a training course, assess trainee learning, and/or answer managers' questions about program effectiveness. 4. Brnich, Derick, Mallett, and Vaught discuss a technique for incorporating worker participation into fire prevention and safe equipment operation training. This technique involves development of short (5 to 7 minutes) videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner's workplace. An example of one of these training modules is presented, along with the results of an evaluation performed on its effectiveness at improving miners' understanding of what types of information they should be sure to communicate during a mine emergency. 5. Wiehagen, Conrad, Friend, and Rethi discuss on-the-job training (OJT) as a method for teaching miners safety and production skills. Much of the training is done by experienced workers. This paper describes how small investments can help improve the effectiveness of on-the-job training. Effective on-the-job training involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. This paper addresses organizational considerations supporting structured on-the-job

Jan 1, 2002

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

UNIT OF MEASURE ABBREVIATIONS USED IN MFIRE FT foot FT3/MIN cubic foot per minute LBM•MIN2/FT4 pound mass times minutes squared over feet to the fourth FT2/HR square feet per hour BTU/HR*FT*F British thermal unit divided by hours times fimes feet times degree Fahrenheit IN W G inches water gage FT3/MIN cubic feet per minute FT2 square feet FT3 cubic feet LBM, pound mass F Fahrenheit IN W G /CFM2 inches water gage per cubic foot per minute squared PERCENTAGE percent BTU/MIN British thermal unit per minute MFIRE BAT PROGRAM cls echo off echo MFIRE activated mfire0 echo Wait a moment for loading the program if EXIST zheng chg mfirel if EXIST zheng chg mfire2 if EXIST zheng chg mfire1 if EXIST zheng chg erase zheng chg if EXIST hang chg erase hang chg if EXIST yunzhi fan copy yaodong.ion+yunzhi fan yaodong ion if EXIST yunzhi fan erase yunzhi fan if EXIST xintan chg copy yaodong xin+xintan chg yaodong ion if EXIST xintan chg erase xintan chg if EXIST yaodong xin copy yaodong.xin mfire out if EXIST yaodong.xin erase yaodong.xin if EXIST net erase net echo Your output is saved in file MFIRE OUT MFIRE0 FOR PROGRAM CHARACTER•50 A OPEN (10,FILE='NET',STATUS='UNKNOWN',FORM='UNFORMATTED') NETWW=0 WRITE (10) NETWW OPEN (21,FILE='ZHENG CHG',STATUS='UNKNOWN',FORM='UNFORMATTED') A=) ' B=0.0 WRITE (21) A WRITE (21) A,B

Jan 1, 1990

By R. Hogg

"Particles play an important role in our environment and in many aspects of human activity. Much of the Earth's surface - sand, soil, rocks - consists of particles, as do clouds in the atmosphere, smoke from fires, and dust in our homes. Many of the foods we eat - cereals, flour, instant coffee - and everyday items such as pharmaceuticals, cosmetics, detergents and other cleaning products are encountered in the form of particles. Inks and paints consist of very fine particles dispersed in liquids. Modem agriculture uses huge quantities of fertilizers and pesticides, largely in particulate form. The list could be extended almost indefinitely; particle systems are obviously an important part of our daily lives. But what do we know about them? For most people, the answer is probably: not much.We are all familiar with the three common states of matter: gas, liquid and solid. In many respects, particle systems should be regarded as a distinct class of their own. The particles themselves may be solid but we all know that a heap of sand is quite different from a solid rock. A cloud of liquid droplets - fog - has much more in common with a cloud of solid particles - smoke - than it does with a bucket of water. There are certain characteristics and properties which are unique to the particulate state. The behavior of any particle system is determined not only by the material from which the particles are made, but also by interactions among the particles and with their environment. These interactions become increasingly important as the size of the particles decreases, and for exceedingly fine particles, smaller than about one micrometer (0.000001 meters or 0.00004 inches), these interactions dominate and we enter the realm of colloidal systems.Particle SystemsA system in which discrete entities - particles -are dispersed in a continuous medium can be regarded as a particulate system. The particles and the medium can consist of a solid, liquid or gas. The various combinations and some common examples are listed in Table 1. The properties and behavior of these systems depend on the characteristics of the particles, the nature of the medium, and the relative abundance of the two phases. In general, it is the latter which determines the kind of behavior exhibited by the system.As a general rule, the behavior of particle systems follows that of the dispersed phase (the particles) at high concentration, and that of the continuous phase (the medium) at low concentration. For example, both powders and smokes consist of solid particles in a gaseous medium. However, in a powder the solids typically occupy over one half of the total volume; in many respects powders behave like solids. In a smoke, on the other hand, the particles may take up only a few parts per million of volume, so that these systems generally behave like gases."

Jan 1, 1989

By L. A. Stewart

"SUMMARYThis paper describes most of the chrysotile-asbestos deposits of Arizona. Mining methods are discussed briefly and asbestos-mill flowsheets are incorporated. Arizona asbestos mines are the only sources on the American continents of naturally iron-free chrysotile spinning fiber that is so urgently needed for electric-cable coverings, especially on warships.Asbestos was first recorded and recognized in Arizona in 1872, and a minor amount was produced from a deposit in the Grand Canyon in 1900. The discovery of a deposit in the Salt River district in 1912 initiated intensive prospecting, and deposits soon were developed. The total Arizona production of all grades of asbestos through 1953 is estimated at 30,000 to 35,000 tons.The deposits of the Central Arizona region, which are discussed in this paper, are scattered over nearly 2,000 square miles. The annual output is relatively small, because the asbestos occurs in thin, discontinuous veins and only in areas where intrusions of diabase are adjacent to or crosscut certain favorable units of the pre-Cambrian Mescal limestone. This stratigraphic limitation, combined with other essential geologic conditions, tends to restrict the size of the deposits.Virtually all of the deposits are in rugged, mountainous country, and many of the mines are on steep canyon walls. In the average mine, production of 1 ton of commercial asbestos requires removal of 30 to 40 tons of waste rock. Mining and transportation costs consequently are high.Several deposits of chrysotile that is somewhat harsh and of moderate tensile strength have been known for years but were not worked because of the former exacting demands of industry for high-strength, soft asbestos. However, improve¬ments in asbestos fiberization and spinning technique, combined with the urgent need for asbestos, have made this so-called semisoft fiber desirable, and deposits of this type now are being exploited."

Jan 1, 1955