Search Documents

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to pieces weighing as much as 5 tons, a 150-ton batch retort was designed and constructed at the Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11-1/2 feel in inside diameter and is supported in a 92-Foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, is currently being used as the test shale. To date, three runs have been completed. Results of the second and third runs are reported in this paper. The two runs considered in this report are the first of a series of nine to determine operating conditions that will yield maximum oil recovery from a column of mine-run shale. Variables studied :ire the oxygen content of the retorting gas and the space velocity of the retorting gas expressed as ft3 gas/ft3 bed/min. Oil recoveries for the two runs reported are 62.2 volume percent of Fischer assay for the run using higher oxygen and space velocity, compared with 39.3 volume-percent when less oxygen and a Lower space velocity were used.

Jan 1, 1971

By R. S. Norman

The objective of this program was to select approximately 100 acoustic materials for flammability evaluation. Noise control programs have been initiated on several types of mining equipment and vehicles which can be used in underground coal mines. Often, the materials which are used in these noise reduction programs have not been tested for flammability properties according to the same reference standard. During this program a variety of materials were selected for measurement according to ASTM E-162 procedures. A radiant heat energy source was used to measure flammability properties of 15.2 x 45.7 cm. samples. In the absorptive materials category, 45 percent of the materials tested had a flame spread index of less than 25. For barrier, damping, and isolation materials the corresponding values were 40, 43, and 9 percent.

Jan 1, 1979

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By Lucia Kuizon

The Antimony RARE II area is underlain principally by Mesozoic igneous rocks associated with the Sierra Nevada batholith. The San Andreas fault zone is near the southern boundary. Metallic mineral deposits are associated with the fault zone. These deposits were formed from magmatic solutions, and tend to be along shears and fractures within the country rock. Marble and dolomitic marble deposits occur in Paleozoic roof pendants or inclusions in the Mesozoic intrusive rocks in the area (Troxel and Morton, 1962, p. 52).

Jan 1, 1982

By J. P. Hansen

The Bureau of Mines has investigated the S02 leaching of MgO from high-MgO-bearing Florida phosphate concentrates. The S02 was effective in leaching some of the MgO from three phosphate concentrates; flow rate of the S02 and leach time were major factors in determining the amount of MgO leached. Calcining the samples, then grinding to minus 200 mesh, and elevating the leach temperature gave only small increases in the amount of MgO leached. The research also showed that some of the MgO was so intimately associated with the phosphate mineral that it could not be removed by S02 leaching. This amounted to about 0.6, 0.7, and 1.0 pct MgO in three leached residues. The calculated heads for the three concentrate samples averaged 1.4, 1.1, and 1.5 pct MgO, respectively, before leaching.

Jan 1, 1985

By J. L. Stauffer, S. L. Lacey, L. J. Gaydos, L. M. Demers, D. C. Kuhn

"Tumor necrosis factor alpha (TNFa) and thromboxane A2 (TXA2) are major products of the activated alveolar macrophage and serve as key mediators of lung injury. In order to determine if the synthesis ofTXA2 and the release ofTNFa are associated, the production of these inflammatory agents by the human alveolar macrophage (AM), as a result of activation by lipopolysaccharide (LPS), was assessed in the absence and presence of the thromboxane synthase inhibitors UK 38,485 (Dazmegrel) and OKY 046. UK 38,485 and OKY 046 inhibited both LPS-stimulated TXA2 production and TNFa release in a dose-dependent manner. Prostaglandin E2 (PGE2) production was not increased by UK 38,485 or OKY 046. Neither LPS nor UK 38,485 had any effect on LT84 production by AM. Neither UK 38,485 or OKY 046 had any effect on LPS-stimulated interleukin-I beta release. However, the TXA2 mimetic, U46619, did not stimulate TNFa release by AM either in the absence or presence of UK 38,485. These findings suggest that 1) UK 38,485 and OKY 046 are inhibitors of both TXA2 production and TNFa release by activated human AM, 2) UK 38,485 probably does not exert its inhibitory action on TNFa release through effects on eicosanoid production and 3) the possibility that TNFa- and TXA2-induced lung injury may be subject to amelioration by imidazole-based compounds should be further evaluated.IntroductionTumor necrosis factor alpha (TNFa), produced by monocytes and macrophages, is a potent peptide mediator of lung injury (1,2). The exaggerated release of TNFa has been implicated in the etiology of acute lung reactions such as septic shock of bacterial or viral origin (3,4). The role of TNFa is expressed primarily through its ability to activate a variety of cell types within the lung environment including polymorphonuclear leukocytes (PMNs, ref. 5), type II epithelial cells (6) and fibroblasts (7). The role of lipid mediators in lung disease has also been extensively characterized (1). In particular, the relationship between pulmonary inflammation and fibrosis and the production of oxygenated derivatives of arachidonic acid (here termed ""eicosanoids"") appears to be a key factor in a variety of disease processes in the lung (8). The alveolar macrophage (AM) synthesizes primarily prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (LT84, ref. 9). These eicosanoids have been shown to produce a variety of effects in the lung including bronchial smooth muscle dilatation (PGE2, ref. 10), vascular smooth muscle contraction and platelet aggregation (TXA2, ref. 11) and oedema and immune cell extravasation (LT84, ref. 12)."

Nov 1, 1995

By McHenry Mosier

A skull breaker has demonstrated its advantages for secondary breaking in a limestone quarry by entirely displacing secondary blasting . It has reduced safety hazards to workmen, increased the number of quarry operating days , and has lowered mining costs by 2.7 cents a ton. It is believed that the application of the skull breaker can be made economically advantageous in the surface mining of other commoditics .

Aug 1, 1948

By George C. Branner

This study was planned to present salient facts of the California and Nevada sulfur industries and to indicate existing opportunities for increased economic utilization of California and Nevada sulfur resources. Numerous publications on sulfur have been issued by the Federal Bureau of Mines, including Information Circular 6329, Sulfur, by Robert H. Ridgway (1930); annual Minerals Yearbook chapters on Sulfur and Pyrites, by various authors; and a chapter on Sulfur by G. W. Josephson in Bureau of Mines Bulletin 556, Mineral Pacts and Problems (1956). This literature, however, deals primarily with the national and international sulfur situation and does not attempt to analyze the possibilities for increased economic development of sulfur resources by individual States. The present study attempts to analyze these possibilities in California and Nevada and to (1) evaluate factors that have influenced production and consumption in California and Nevada and (2) indicate apparent trends in production, consumption, and prices in these States.

Jan 1, 1959

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By R. E. Stiles

The modified perchloric--EDTA method devised by the Bureau of Mines for the determination of copper in high-grade samples gives results that are more precise and more accurate than those from the classical sulfuric-iodometric method. Although the perchloric--EDTA method is more costly than the conventional method, the savings in time alone largely offsets this difference. Specifically, the modifications wade in the more conventional procedure comprise (1) use of perchloric acid instead of sulfuric acid for dissolution of copper minerals, (2) precipitation of copper as copper sulfide from dilute perchloric acid solution, (3) wet oxidation and dissolution of the precipitated copper sulfide, (4) use of larger amounts of indicator than those employed in the Schwarzenbach method of titrating low-tenor copper solutions with disodium ethylenedinitri10-tetraacetate and murexide indicator, and (5) use of refrigeration to partially stabilize aqueous solutions of the indicator.

Jan 1, 1966

By John D. Bradley

Stibnite is 76 miles east of Cascade, Idaho, which is 78 miles due north of Boise. The altitude at Stibnite is 6,500 feet, and between Cascade and Stibnite the Forest Service road crosses two summits - Big Creek at 6,800 feet and Warm Lake at 7,300 feet. The ownership of most of the Meadow Creek group of 190 claims, which is optioned by the Bradley Mining Co from the United Mercury Mines Co. may be traced back from their consolidation by the United Mercury Co. through ownership by prospectors and small promotional companies to the discovery of the Thunder Mountain district in 1900 by the Caswell brothers.

Jan 1, 1942

By Eugene Frey

The Romur is one of several properties in the Copper Mountain mining district, Fremont County, Wyo., that contain scheelite deposits. The district lies on the southern slope of the Bridger Mountains, 18 miles northeast of Shoshoni and 15 miles from the rail point at Bonneville on the Chicago, Burlington & Quincy Railroad (figs. 1 and 2). The tungsten deposits occur in a zone of pre-Cambrian schists and gneisses that have been cut by numerous basic dikes and granite pegmatite dikes. Scheelite occurs in lenses and pods that lie parallel to the foliation and bedding in the metamorphic rocks. The more important deposits are found in a lime-silicate rock consisting primarily of zoisite but with small quantities of quartz and carbonate. Scheelite was found in December 1941, and the area was mapped by the U. S. Geological Survey early in 1942. In November 1942 the Bureau of Mines commenced work on the Stardust-Comet group for the purpose of developing reserves for war requirements. The initial work consisted of driving an alit in the ore zone a distance of 109 feet. This zone was sampled during the progress of the work, and subsequently surface and underground exposures on adjoining properties also were sampled (figs: 5, 6, 7, and 8). One hundred twenty-four samples were obtained. Sample and assay data are shown in tables 2, 3, and 4.

Jan 1, 1950

By F. W. Lane

Some months ago the Bureau of Mines began research of a fundamental character on sulphur in petroleum. In the course of this work, the usual qualitative test for sulphur in organic compounds1 was applied to certain oils that were believed to contain approximately 0.5 percent sulphur. No sulphur was found, and, as a check on the qualitative test, the oils were subjected to quantitative determination of this element by the oxygen-bomb method.2 The sulphur content of the oils ranged from 0.10 per cent to 0.50 per cent. This experience led to further trial of the qualitative test for organic sulphur, both on the oils mentioned above, and on common sulphur-containing organic substances. No difficulty was experienced in detecting the element in the latter, but with the petroleum oils the test, as usually performed, could not be relied upon to detect less than 0.60 per cent of sulphur consistently. The use of mechanically polished pure sheet copper for the detection of free sulphur, hydrogen sulphide, and perhaps other sulphur compounds has been recommended.3

Jan 1, 1927

This U.S. Bureau of Mines (USBM) report conveys the results of an economic analysis of minerals in the West Mojave Management Area (WMMA), including the Desert Tortoise Priority Habitat (DTPH), a proposed special land management area. Undiscovered mineral resources were estimated for the entire WMMA, which totals 8.7 million acres. Known mineral resources were studied for the DTPH, which is an area of 1.2 million acres contained within the WMMA. Federal lands within the WMMA are managed by the Bureau of Land Management (BLM). The WMMA includes Federal, State, and private lands in the western portion of San Bernardino County and the eastern portion of Kern County. The center of the study area is 20 miles northwest of Barstow, California (Figures 1 and 2).

Jan 1, 1993

By David E. Siskind

The Bureau of Mines recorded particle accelerations in the mine roof produced by three types of explosives in the Pilot Knob Pellet Co. mine, Pilot Knob, Mo. Examined were the effectiveness of cube root, square root, and two-thirds power scaling in grouping the underground blast vibration data, and the effects of mine geometry, rock type, explosive type, and charge size on blast vibration levels. A propagation law for this mine was determined. The scaling factor of the square root of the charge weight was developed from previous Bureau studies of vibrations from quarry blasts, and in under-ground blasting both square root and cube root scaling were found applicable for scaling particle vibration data. The vibrations from the Pilot Knob blasts were best grouped by a square-root scaling factor. The empirical propagation equation AW1/2 = 76,250 (R/W1/2)-2.61 where A is the peak acceleration in g's, W is the charge weight in pounds, and R is the distance from the blast in feet, may be used to describe vibration amplitudes from charges fired with zero delay caps or with a single cap at Pilot Knob. Statistically significant differences were found in the vibration levels generated by the different explosives. The Power Primer (75-percent weight-strength ammonia gelatin dynamite) produced levels of vibration of 1.7 to 2.4 times those of AN-FO and slurry explosives; the latter two are approximately equal.

Jan 1, 1973

By R. P. Jewett

The object of this investigation was to correlate the crushing strength of green pellets prepared from magnetite, specular and earthy hematite with the particle size of these respective raw materials. In this study no attempt was made to correlate the strength of fired pellets and particle size. The effect of particle size upon a number of fine ores and concentrates was studied. Much of the low-grade ore reserves in the Lake Superior Region must be finely ground before concentration and then agglomerated for iron and steelmaking processes. Fine natural ores also must be agglomerated. Pellets constitute an important type of agglomerate. Considerable handling occurs during screening to remove undersize and oversize pellets, and in transfering green unfired pellets from the balling machines to the heat-hardening equipment. As a result the strength of the green pellets is a factor of great importance.

Jan 1, 1961

By M. E. Volin

The Buckeye manganese deposits are in Stanislaus County, Calif., about 33 miles south of Tracy. From 1917 to 1919 the deposits produced 13,370 tons of ore reported to average 46 percent manganese and 14 percent silica. The deposits are confined to two areas of' development, known as the north mine workings and the south mine workings, about 700 feet apart horizontally. Mineralization occurs chiefly as rhodochrosite and psilomelane interbedded in cherts of the Franciscan formation. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a development project was started November 25, 1940, and completed June 27, 1941. The Federal Geological Survey cooperated by mapping the topography and geology and logging the drill cores. The program included road and. trail building, trenching, underground excavation, diamond drilling, and sampling. The following pages mention the location, brief the history, and note the physical .features of' the district. Mine workings are sketched, the deposit is described, and the plan of the project is noted. The work performed by the Bureau of Mines is explained in the concluding pages with a summary of the drill-hole logs.

Jan 1, 1949

By John F. Papp

The Bureau of Mines has sampled microstructure of low-pressure flat flames by mass spectrometer for normal methane-oxygen-argon and for methane-oxygen-argon-bromotrifluoromethane flames. The physical and chemical phenomena, and the method of analysis of mole fraction data to evaluate net reaction rates are here considered in detail. Included is a computer program listing with output on one flame. Chemical species considered are CH4 , CO, CO2, H, H20, OH, Ar, H2, O2 , O, H2CO, CH3 , CF3Br, HF, HBr, Br, CH3Br, HCO, F2CO, CH2 CF2 , H02.

Jan 1, 1975

By Martin H. Rogoff

The presence of antibiotic materials extractable with polar organic solvents was demonstrated in coals of various ranks. Since these antibiotics occur in low concentrations, 200 pounds of a high-volatile C coal was extracted with acetone at room temperature to obtain sufficient material for detailed study. The biologically active materials in the extract were concentrated by extracting with aqueous sodium hydroxide. The fractions soluble in sodium hydroxide inhibited bacterial cultures when present in concentrations comparable to those at which other antibiotics are active (5 µg/ml). Steam distillation of the extracts did not yield highly active materials, contrary to the finds of other investigators. Mass spectrometry of the extract indicated, mainly, the presence of 6-ring compounds in the region of mass 324 to 392. The predominance of 3-ring aromatic systems found by ultraviolet analysis suggests compounds such as biphenanthryl or similar structures. The activity of the hydroxide- soluble material decreased markedly when the phenolic hydroxyl groups were transformed into trimethylsilyl ethers. Hydrolysis of the ethers yielded a product having the same activity as the original material, which indicates that phenolic compounds are largely responsible for the antibiotic activity observed.

Jan 1, 1963