Search Documents

By John J. Mulligan

The Bureau of Mines investigated reports of mineral deposits within 10 miles of the route of the proposed pipeline from Prudhoe Bay to Valdez. No producing lode deposits or lode prospects of possible national economic significance were found. Measured placer deposits in the route are or slight value except possibly some deeply buried gold placer deposits in the Fairbanks and Livengood Quadrangles. The pipeline corridor crosses five belts of minerals having potential economic value: (1) The north slope of the Brooks Range (oil, gas, oil shale, coal, phosphate); (2) the south slope 01 the Brooks Range (copper, gold); (3) the Livengood area (gold); (4) the Fairbanks area lead-silver, antimony); and (5) the Wrangell Mountains-Denali copper belt (copper-gold). The Jarvis Creek coalfield, an eastern extension of the Nenana coalfield, is on the north side of this belt. Scattered along the corridor across the Chugach Mountain and in the vicinity of Valdez are a wide variety of metallic deposits that make up the eastern margin of the Chugach gold belt but do not seem to constitute a well-defined zone.

Jan 1, 1974

"The U.S. Bureau of Mines established on August 15, 1983, The Generic Mineral Technology Center for Respirable Dust (Dust Center) within the Mining and Mineral Resource Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University, and in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. In 1986, Michigan Technological University (MTU) was awarded a grant through the Dust Center. The center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health law, which is ""... (to) permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis of any other occupation-related diseases..."" The Dust Center's program is designed to foster an accelerated attack through fundamental research on problems confronting the control of respirable dust in mines. The interactions of the universities and the research program components in the characterization of coal seams, respirable dust particles and the workers lungs are depicted in the logo of the Dust Center.The primary goal of the Dust Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The Dust Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection of dust in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) the relationship of the mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines, and to other dusts such as those generated by diesel equipment. Achieving the Dust Center's goals also involves the training of engineers and scientists, graduate students, and undergraduate students through their respective institutions, and technology transfer to industry. The distribution of personnel in the various universities are presented in Table 1. A directory of Dust Center principal investigators is presented in Appendix 1. A summary of degrees granted and mineral sector employment is presented in Table 2. The subjects of theses developed under the various research projects are presented separately in Volume 7. The center research is fully compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities (see Volume 2). Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease studies are available as a result of the existing relationship between NIOSH and West Virginia University. Figure 1, Respirable Dust Center Projects and Activities, presents the various projects in the five major areas of investigation and the scope of characterized dust samples, the suite of tests, the sampling and dust generation methods, and the size, chemical and mineralogical analysis performed in the center. Table 3 presents a summary distribution of the 95 publications and presentations that have emanated from the center. In addition there are more than thirty presentations made at each annual Dust Center review meeting. The titles, authors and location of presentation for publications supported by the Dust Center are presented in separate publication volumes for 1984 (Volume 3), 1985 (Volume 4), 1986 (Volume 5) and 1987 (Volume 6)."

Jan 1, 1988

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This article focuses on U.S. Bureau of Mines (USBM) and National Institute for Occupational Safety and Health (NIOSH) research to examine factors that had a significant influence on mine face ventilation design during the past century. Several "milestone" events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative face ventilation designs and a consistent commitment to mining health and safety. Ventilation has always been a concern in underground coal mining. For many yeas, there was no appreciation of how ventilation could be used to remove harmful contaminants from the air or how to control airflow quantities. The first known problems with ventilation date back to the 14th century, when it was recognized that lack of air was a major impediment to the expansion of mines. The common method of solving ventilation problems at that time was to abandon the existing mine and start a new one nearby. Ventilation in the early days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings. Later, in the 18th and 19th centuries, a furnace was introduced underground to increase the updraft in the return shaft. This allowed for a larger quantity of air in circulation. When mines went deeper and became larger, mechanical ventilation became necessary and was first accomplished by steam-driven fans. These fans became more prevalent as furnaces were prohibited in underground mines, especially after the Avondale disaster in Pennsylvania in 1869 (Roy, 1876). Eventually, these fans were replaced by more powerful, electrically [ ]

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

Viable domestic mineral industries are essential to the economic health of the United States and the well-being of its citizens. The charts in this publication reflect developments significant to the Nation's mineral industries during 1975. Last year was a year of reduced activity for the Nation's mineral industries. Although the value of the country's total mineral output rose, for example, the overall production and use of many minerals fell. At the same time, the industry experienced lower profits and higher debt/equity ratios. These and other adverse effects on many segments of the Nation's mineral industries resulted from the overall decline in domestic and international economic activity.

Jan 1, 1976

Objective To accurately measure very low air velocities (0-100 ft/min) in U.S. large-opening underground metal/nonmetal mines. Background Hundreds of metal/nonmetal underground mines operate throughout the United States. They extract commercial products from deposits such as limestone, salt, and gypsum. Mining generates a wide variety of gases and dusts, such as silica, diesel exhaust, radon, blasting byproducts, and perhaps even methane. If these substances become airborne, they can adversely affect the health and safety of underground workers. Many metal/nonmetal mines have large cross-sectional airways that could be 60 times larger than an average underground coal mine entry. These large airways require adequate volumes of fresh air to dilute, make harmless, and exhaust the toxic and, at times, explosive byproducts. However, in some underground mine sections, air movement is barely perceptible. The technology of measuring very low air velocities will become increasingly more important for operators of large-opening stone mines in order to monitor miner exposure to diesel particulate matter. Conventional anemometers (e.g., vane) are capable of accurately measuring air velocities only above 100 ft/min. Thus, it was necessary to investigate other anemometry technology to detect low air velocities in the range of 0-100 ft/min. Two different portable ultrasonic anemometers were tested. Actual testing was done in an underground limestone mine with openings about 51 ft wide by 29 ft high. Ultrasonic Anemometers Vane-type anemometers are commonly used by engineering personnel throughout the underground coal mine industry. They work well in measuring air velocities >100 ft/min. However, a separate technology, e.g., portable ultrasonics, is needed to measure air velocities much below 100 ft/min at various places within the large mine opening. Laser-doppler technology was also considered for this application, but was ruled out because of its high cost and other technical limitations. With no moving parts, the portable ultrasonic anemometers are claimed to be accurate down to about 1or 2 ft/min. The first type of ultrasonic anemometer that was examined underground is manufactured by Gill Instruments Ltd., Hampshire, U.K. The U.S. distributor is IN USA, Needham, MA. The Gill Instruments Solent Volometer (figure 1) is a battery-powered, single-axis anemometer meant for measuring low to medium air flows up to1,999 ft/min. It uses the ultrasonic "time of flight" principle where pulses of high-frequency sound are transmitted along the air flow path and the time taken to reach the receiver is measured. The faster the air speed, the quicker the pulses reach the receiver. The second ultrasonic anemometer that was examined under-ground is manufactured by Airflow Developments Ltd., Buckinghamshire, U.K. The U.S. distributor is Airflow Technical Products, Inc., Andover, NJ. The Anemosonic UA-6 (figure 2) is a battery-powered, handheld instrument with digital display. It measures air velocity (0 to 9,999 ft/min) or volume flow, flow turbulence intensity, and air temperature. Neither device is considered to be intrinsically safe for use in underground gassy coal mines. A comparison of salient specifications of both instruments is shown in table 1. The total suspended weight includes the instrument (Gill) or instrument probe (Airflow) plus about 35 ft of connecting cable attached to the pole. This combination of instrument plus cable length allows two operators to measure air velocities up to about 30 ft above the mine floor. Figures 1 and 2 show how each unit would be attached to an extensible, graduated fiberglass rod in order to position the sensor probe at a certain spatial point (centroid of the quadrate) within the underground large opening.

Jan 1, 2003

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX C - HOISTING SYSTEMS - AVAILABLE EQUIPMENT C 1 - Introduction A survey has been made of available hoisting equipment which has applications for use in metal and non-metal mine emergency escape hoist systems. The information was gathered from a number of sources, including representatives in the USBM and MESA, mine operators, personal visits and telephone interviews with manufacturers, field visits to inspect equipment, advertisements, catalogues and indices of manufacturers. Wherever possible, technical specifications and prices were checked out with the manufacturer, or supplier. The sections on individual sub-systems and components, such as automatic control systems, winches and controls, are not intended to be all encompassing surveys. Rather a reasonable number of representative units in each category are discussed. The sample is large enough to provide a general picture of the kind of equipment available, including the abilities and limitations and a reasonable price range. The survey has been divided into six categories 1. Complete Hoisting Systems A Above ground installations B Below ground installations 2. Hoist Assemblies ^(Man-rated) 3. Hoists (not Man-rated)

Jan 1, 1976

By Oliver Bowles

Chalk is defined as a noncrystalline, soft, friable, fine-grained, light-colored type of limestone. It consists essentially of calcareous shells of minute organisms known as "foraminifera," although skeletal remains of molluscs, corals, and sponges are also present. Flint balls which are found so commonly in the chalk cliffs of Europe are regarded as segregations of the remains of certain organisms, such as radiolarians and sponges, that secrete siliceous shells or spicules. The famous chalk beds of northwestern Europe are of Upper Cretaceous age, a geological period that was particularly favorable for the develop- ment and multiplication of foraminifera. The distinguishing physical characteristics of true chalk never have been fully defined; probably its noncrystalline and colloidal properties are most important. The properties of chalk, whiting, and whiting substitutes are not well understood, and much re- search is necessary before definite reasons may be ascribed for the behavior of these materials under various conditions of use. The Bureau of Mines has undertaken a detailed study of chalk and similar materials to determine their exact properties and to establish a basis for classifying formations loosely designated as chalk occurring in various parts of the United States, but the results of this study will not be available for some months. Whiting is a pulverized, purified, and carefully sized chalk. Whiting substitutes consist of finely ground limestone or dolomite, ground marble (marble flour), white marl, and chemically precipitated calcium carbonate.

Jul 1, 1931

By R. V. Ramani, S. Shankar

"Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991 ). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken:• a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities;• a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and• the mathematical modeling and computer simulation of the re-entrainment phenomenon.In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies,it was observed that increasing the air velocity increased the rate of re-entrainment ( Shankar and Ramani, I 994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to air flow was negligible compared to the contribution due to walking. IntroductionIn underground coal mines, dust is produced primarily during the process of mining and during such activities as pillar spall, loading, belt transfer and roof fall. The generated dust is entrained and then collects on surfaces through dispersion, diffusion and eventual deposition. Removal forces, such as flowing ventilation air or turbulence caused by walking and moving vehicles, can re-entrain the deposited dust (Hall, 1955). A portion of the re-entrained dust remains airborne and increases the concentration of airborne dust in mine airways.The presence of airborne coal dust in mine airways in large concentrations can be hazardous. Health effects include coal workers' pneumoconiosis (CWP) and silicosis, and it can be a nuisance affecting visibility. In addition, as is common during methane explosions, if the concentration of airborne coal dust becomes significant, there could be a coal-dust explosion (Singer, Cook and Grumer, 1972; Singer, Harris and Grumer, 1974; Edwards and Ford, 1988). Through concerned research efforts over the last decade, significantprogress has been made in reducing the airborne dust concentration in mine atmospheres. However, secondary sources, such as re-entrainment, have not been studied in-depth. It is important to understand the phenomenon of re-entrainment and its potential contribution to the airborne dust concentration in mine airways for further decreasing airborne dust hazards in mines."

Dec 1, 1996

By David E. Fogelson

The breakage of rock by explosives depends largely on the ability of an explosive to transfer its stored potential energy to the rock as strain energy. Therefore, the relative rock-breaking abilities of explosives can be determined indirectly by determining the relative amounts of strain energy transferred to the rock at the time of detonation. This report presents experimental data on the strain energy contained in explosion-generated strain pulses in a granite gneiss. Six explosives were tested. The scaled total radial strain energy Es/W flowing outward through a spherical shell of scaled radius R/W1/3 surrounding the point of detonation was found to follow an exponential decay propagation law of the form [ ]

Jan 1, 1959

By F. S. Crawford

Mining companies are usually held responsible for accidents occurring to the public around their operations . Safeguards are provided by progressive mining companies to prevent the public from getting into danger from wandering unattended about the properties . At abandoned operations , where little or no supervision can be maintained , persons are often injured through the negligence of the operator in leaving the property in unsafe condition . After a mine is abandoned or a lease is given up by a mining company , the responsibility for the safety of the property rests sometimes with the State to which the property ownership reverts or with the owner of the land ; either is usually quite unwilling to spend any money to remedy unsafe conditions due to the carelessness of the mining company . The land owner or the State , or both , should see that the work of leaving safe conditions behind is done by the operator before he abandons the mine or gives up the lease . Some of the worst hazards to the public at abandoned mines are from old test pits , abandoned shafts or tunnels , open pits , caved ground , and bodies of water in abandoned open pits . Hazards exist from some of these sources during the active operation of a mining property as well . In the early stages of mining operations test shafts are often sunk from 50 to 100 feet deep through the more or less loose material overlying bed rock . When these shafts are left unprotected , they are a serious danger for many years to come . In the course of time they become largely concealed by brush and grass , and thus are a deadfall to anyone who might happen to step into them . This condition will hold true for any part of the country, but to a much less degree where it is not necessary to sink through a great amount of cover . Many progressive operating companies have adopted the practice of filling in test pits after securing the information desired . Some nonresident landowners and exploration companies , however , have left such pits open , and it is extremely difficult for the mine inspector to get into communication with the owner . Frequently operating companies voluntarily fill test pits on adjacent property not

Jul 1, 1930

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By Richard A. Winters

In 1985 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 9,400 acres of the 10,005-acre Duncan Creek Wilderness Study Area (ID-111-78) in order to evaluate the mineral resources. The study area is located in Owyhee County, 10, about 36 miles southwest from Bruneau, ID. No mining districts are in the study area, nor were any mines or claims recorded or found. The southern half of the area was covered by oil and gas lease applications, all of which were cancelled prior to June, 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Duncan Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By J. J. Jakowsky

[The legislation in many States against the present method of producing carbon-black by the incomplete combustion of natural gas, and the continually increasing demand for gas for otter purposes, indicates that the supply of carbon-black may Gradually be decreased and that new methods for its production, utilizing a greater parentage of the carbon in the has should be developed. In the course of investigations of the effects on hydrocarbons of high voltage discharges, it was noted that under certain conditions natural gas could be decomposed and that carbon-black could be produced. The effects of several tyres of electrical discharges on natural gas have, accordingly, been studied' in order to find out the fundamental factors underlying the reactions and their possible influence in the recovery of a greater part of the carbon content of natural gas than is now possible. Present commercial plants using natural gas for the manufacture of carbon-black recover from 0.9 to 1.5 pounds of carbon-black per thousand cubic feet of gala consumed, or less than 5 per cent of the total Gabon in the gas: It should be noted, however, that the, present methods involve heating the gas to incandescense by burning it as a luminous flame, and a considerable part of the gas is thus consumed as a source of hest. If this heat can be supplied from some other source, or if a more efficient method of applying the energy con. tamed in part of the gas, to the decomposition of the rest of it, can be worked out, then a greater yield of carbon-black per thousand cubic feet of gas care be expected. The present abort paper contains a brief summary of tie investigations so far conducted upon natural gas.]

Jan 1, 1922

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young's modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954

By D. Bienstock

The Fischer-Tropsch synthesis is practicable in a reactor where the exothermic heat of reaction is removed by circulating large quantities of recycle gas through a catalyst bed of high-voids content. At an hourly space velocity of 1100, the feed gas, a mixture of 1.5 parts hydrogen to 1 of carbon monoxide, was converted 90 percent, producing hydrocarbons predominantly in the gasoline range. At these conditions a recycle-to-fresh gas ratio of 40:1 was enough to give excellent temperature control with a pressure drop of 1.5 p.s.i. per foot of bed using a steel catalyst in the form of lathe turnings. Steel parallel plates, although offering lower resistance to gasflow, were less reactive and less durable. INTRODUCTION The Federal Bureau of Mines has been engaged in a research and development program since 1944 on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a synthesis gas--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va.; and the synthesis of gasoline by catalytically reacting the carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By H. W. Kilau

The Bureau of Mines used a high-temperature rotational viscometer to test basic oxygen furnace slags to determine fluorspar requirements and to evaluate colemanite and fused boric acid as substitute fluidizers. A continuous technique of viscosity measurement was adapted to better determine the viscosity-temperature profiles of volatile fluorspar slags. Criteria used for estimating slag fluidizer effectiveness were (1) the apparent solidification temperature, and (2) the temperature range of slag crystallization. Colemanite and fused boric acid in high-basicity slag were superior fluidizers to fluorspar when compared on the basis of boron versus fluorine concentration. Fused boric acid was nearly equivalent to ceramic-grade fluorspar when compared on a simple weight basis, while colemanite was inferior to fluorspar. Fluorspar slags volatilized fluorine during viscosity testing. Colemanite and fused boric acid slags were stable, no boron losses being detected. A fluidizing limit was found for fluorspar at 2.9 percent fluorine concentration; higher concentrations impaired viscosity and caused foaming and crusting of slag. Concentrations of boron up to 4.4 percent resulted in very fluid slags with no fluidizing limit.

Jan 1, 1978

By John Nagy

Experience and research have shown that an effective way to reduce structural damage from explosions is to provide adequate pressure-relief vents in the walls of equipment and buildings within which explosions might occur. In general, free or unrestricted openings represent the most efficient type of vent. However, in many manufacturing operations it is impractical to use free vents, and it becomes necessary to cover the openings with diaphragms or blow-out disks, hinged panels, or other devices, in order to give protection against weather changes, to prevent the efflux of dusts or vapors from equipment during normal operations, or for other reasons. A few data on the pressure-relieving capacities of hinged panels and a paper diaphragm were published in Bureau of Mines Report of Investigations 3924, which covered the first phase of the dust-explosion venting study made by the Bureau. The present report describes recent experiments that were made to determine the relative effectiveness of an unrestricted vent and 22 types of closures, including various paper, cloth, and metal-foil diaphragms, hinged doors or panels, and several kinds of scored and unscored glass panes. The tests showed that many of the vent closures were effective in releasing the explosions rapidly during their incipient stage, so that the development of destructive pressures was prevented. Vents of this type should prove useful in safeguarding industrial equipment from severe explosion damage. The experiments disclosed that the venting capacities of the diaphragms are approximately inversely proportional to their static bursting strengths.

Jan 1, 1950

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010