Search Documents

By Jack L. Henry, Davis E. Traut, L. R. Penner

The Bureau of Mines conducted solvent extraction batch tests to evaluate the usefulness of neodecanoic acid ( NDA) for extracting Co 3+ from ammoniacal leach liquors high in ammonium sulfate . This work is an outgrowth of previous Bureau research in which technology was devised for the recovery of cobalt , nickel , and byproduct copper from domestic laterites . The previously devised technology uses an oxidative ammoniacal sulfate leach to treat the laterite , and nickel and copper are then recovered from the leach solution by solvent extraction and electrowinning . This report deals with the subsequent solvent extraction of cobalt from the nickel - copper raffinate solution . The results showed that about 70 pct of the contained Co 3+ can be extracted batchwise at pH 8 using NDA ( a 10 - carbon - chain highly branched carboxylic acid ) . However , NDA had a solubility of approximately 0.6 to 0.8 g / L in aqueous raffinate following extraction , and this high solubility makes it impractical for use with alkaline solutions that are low in cobalt . In addition , the extracted cobalt species ( predominately cobaltic hexammine ) is not amenable to the electrolytic recovery of cobalt metal because of its extreme stability . This fundamental prob-

Jan 1, 1965

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By J. M. Singer

Thermal, mechanical, and physical properties of virgin and heat-treated Pittsburgh seam coal were determined as part of a comprehensive study of combustion of monolithic coal block. The information was sought to help characterize pyrolysis and combustion processes in underground coal mine fires but should also prove useful in the study of in situ and surface coal gasifiers. Measured properties include thermal conductivity, specific heat, thermal expansion, density, compressive and tensile strength, porosity, and permeability. The transport property data were obtained (when feasible) in two mutually perpendicular directions of the anisotropic virgin coal material, and coal samples carbonized for 5 hours at temperatures of 350° C, 475° C, 500° C, 650° C, and 850° C. Other coals (Pocahontas No. 3, Sewell, and Illinois No. 6 seams) were investigated for porosity and relative permeability. Interdependence among all properties was evident from the results; however, only a few correlations could be developed owing to inhomogeneity of coal material and specimen variation, which had the effect of reducing the accuracy of measurement and increasing data scatter.

Jan 1, 1979

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By A. J. Barry

Recent developments in mechanizing longwall it mining in Europe have aroused considerable interest among American coal-mine operators because this method provides an opportunity to improve safety, production, efficiency, and recovery. The success of longwall mining in Europe has depended to a large degree on development of effective roof-control systems. One of the major contributing factors in designing these systems is development off improved supports, which combine high load-bearing capacities with controlled yield characteristics, to use in the face areas. Other factors that relate to successful longwall mining involve knowledge of the structural properties of the strata above end below the coal bed being mined, movements of these strata induced by mining, and effects of the strata movements on the strata itself, as well as on the support system used. Extensive studies of the above factors relating to long-wall mining have been made in coal-mining countries abroad, and corresponding studies (1, 2, 3, 4, 5)3/ of room-and-pillar operations have been made in this country. Although descriptions and results of experiments of mechanized longwall operations in the United States have been published (6, 7, 8), this is the first instrumented study of roof behavior on a longwall operation. In view of the possible widespread application of this method of mining to American coal mines, where underground mining conditions are different from those found in European mines, an investigation was conducted at a mechanized longwall operation inn the Lancashire No. 15 mine, Barnes & Tucker Co., Cambric County, Bakerton, Pa., to study the factors that affect roof control. This report describes this investigation and discusses the results. ACKNOWLEDGMENTS This investigation was made under a cooperative agreement between the Bureau of Mines and the Barnes & Tucker Co., Barnesboro, Pa., end was conducted in the Lancashire No. 15 mine located at Bakerton, Cambria County, Pa. The authors acknowledge the cooperation given by Richard Z. Todhunter, Sr., president, Richard T. Todhunter, Jr., general manager, and other mine officials and employees of the Barnes & Tucker Co. Mr. Edward Thomas, chief, Roof Control Section, Bureau of Mines, Washington, D. C., and Dr. Leonard Obert, chief, Applied Physics Branch. College Park, Md., collaborated in the planning and promulgation of the program investigation.

Jan 1, 1954

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By William C. Cooley

A review was made of two Russian books and a chapter from a third book dealing with pipeline transport of coal. Emphasis was placed on hydrotransport of coarse coal in underground mines or surface pipelines. The books reviewed were: "Means of Increasing the Effectiveness of Hydrotransport," by V. N. Pokrovskaya (1972), "Parameters and Modes of Hydraulic Transport of Coal" by V. V. Traynis (1970), and the chapter "Calculations of Hydrotransport of Useful Minerals and Waste Rock" from the book "Hydromechanization of Opencast Workings" by G. A. Nurok (1970). All three are unique and useful additions to the world literature on hydrotransport. The Traynis book reveals the development and results of circular wheel stand tests to simulate hydrotransport in horizontal pipes, which is a potentially outstanding contribution to slurry pipeline technology. Graphical data and equations are presented which suggest that headlosses for coarse coal can be predicted with good accuracy for pipe sizes up to 14 inches in diameter. Wheel stands permit tests for pipe wear and lump degradation without recycling coal through pumps. Recommendations are made for wheel stand tests and for correlation of existing data.

Jan 1, 1976

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

By Donald F. Reed

In the latter half of 1948 the Bureau of Mines investigated the Magnet Cove Rutile Co.'s prerty in northern Hot Spring County, Ark. This work was supplemental to the work done by the Bureau on the same property in 1945.2/ It was undertaken for the purpose of investigating the extent of the ore body toward the south and west and at depth and to obtain representative samples of the ore for metallurgical tests. For the latter purpose, the samples were so taken as to minimize alteration of the physical characteristics of the ore, these characteristics being determining factors in working out processes of bencficiation. During the investigation, 27 holes were drilled, 10 with a diamond-coro drill end 17 with churn-drill rigs using a Baker standard cable-tool core barrel. Drilling developed an extension of the ore deposit westward from the previously mined area but did not disclose the full depth of mineralization. Metallurgical tests to determine methods of beneficiating the ore and utilizing the resultant products are now in progress.

Dec 1, 1949

By James Spiers

This paper describing the mining practice at the Central-Eureka mine is one of a series of similar papers being prepared by the United Staten Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described in this paper are illustrative of the methods employed in the exploitation of comparatively low-grade gold ores under the extremely heavy and swelling ground conditions which occur in the Mother Lode belt of California. The Central-Eureka Mining Co. comprises a group of adjoining mines in Amador County near Sutter Creek. The principal mines of the consolidated group are the Central-Eureka, formerly known as the Summit mine, and the Old Eureka mine, which is also known as the Hayward Quartz mine. The group is situated in the most productive part of tae main Mother Lode belt, the 10-mile portion which lies between the towns of Plymouth and Jackson. The three largest producing mines of the entire belt at the present time are the Argonaut, Kennedy, and the Central-Eureka; these lie within a radius of less than 1-1/2 miles.

Jan 1, 1931

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

Although alternating-current (a.-c.) power systems and equipment have been used in coal mining for many years, most mines in the United States are powered mainly by direct current (d.-c.). There are several logical reasons for this, but the use of d.-c, equipment is, in most instances, a direct outgrowth of the original practice of using such power for haulage systems. For traction equipment such as the electric trolley locomotive the d.-c. motor has ideal operating characteristics, and thus it has been widely used for haulage locomotive service. The first efforts at electrification of coal mines started with the haulage system and from there branched out to include the many types of electrically powered mining machinery used in the industry today.

Jan 1, 1960

By E. G. Davis

The Bureau of Mines made laboratory-scale experiments to examine the technical possibilities of reclaiming manganese from slags produced by oxygen lancing of high-manganese pig iron. Ferromanganese was added to molten pig iron to yield a 4-to 5-percent manganese hot metal, which simulated a product obtainable from the blast furnace. This was injected with oxygen to reduce the metal to 1 percent or less manganese and form a slag containing about 40 percent manganese. The molten slag was water-quenched, treated with H2SO4) roasted at 660° C, and water-leached to give soluble manganese and iron sulfates. The sulfates were precipitated as hydroxides, converted to the oxide form, and smelted to produce a standard ferromanganese containing 74.6 percent Mn and 0.01 percent P. As an alternate method of manganese recovery, a manganese cell feed was prepared from the leach solutions and electrolytic manganese was produced. Direct smelting of the high-manganese slag resulted in 74.2 ferromanganese meeting ASTM specifications except for phosphorus content. The high phosphorus content of the metal and high slag-to-metal ratio obtained made this approach unattractive.

Jan 1, 1966

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By H. J. Heinen

To maximize productivity through improved minerals processing technology, the U.S. Department of the Interior, Bureau of Mines, is investigating particle agglomeration techniques as a means of increasing the percolation rates of leach solutions in heap leaching of clayey gold-silver ores. Simulated heap leach experiments were conducted on 50-pound charges of ore that were contained in 5.5-inch-diameter columns, 5 feet in height. Results indicated that the percolation rate of cyanide leach solution could be enhanced markedly by mixing the ore with controlled amounts of lime, flocculants, and water, and then aging the mixture prior to the column leach step. Experimental results obtained on 20-mesh silver tailings and gold ore crushed to 3/8 inch and to 1 inch showed that it was possible to increase percolation rates as much as 100-fold without sacrificing silver-gold extraction. Larger scale tests conducted in 24-inch-diameter, 16-foot-high columns closely paralleled bench-scale results. By improving percolation leaching, these techniques have the potential of helping to solve environmental problems associated with tailings disposal as well as making an important economic impact on gold-silver recovery operations. Investigations are continuing to develop binders superior to lime for particle agglomeration pretreatment.

Jan 1, 1979

By J. B. Vander Sande, L. C. Rainey, P. Bolsaitis, B. Dirsa

"The structure and composition of silica-rich particles recovered by lavage from the lungs of three active miners with different medical histories were studied using high-resolution electron microscopy and chemical microanalysis. The results arc compared to the similarly determined structure and composition of respirable-size mineral particles obtained from roof-bolter dust-box samples from two coal mines of widely different bulk quartz concentrations. The results show that the lungs of the miners contain silica-based particles with structures not found in the mine samples. Also, the particle structures and compositions found in the macrophages were different in each of the miners. The rau.lu suggest the possibility that intracellular processes may affect the susceptibility of individuals to silica-induced pneumoconiosis. The cytotoxic and fibrogenic potentials of mine dusts result from the activity of their individual components. Whether this effect is additive or even mass (i.e., dose) related is questionable and has been the subject of many investigations. Particle size and size distribution of various constituent minerals, the surface structure and properties of individual particles, and the self-cleaning capability of the lung (i.e., the capacity of the macrophage system) may, among other variables, affect the pathogenic changes induced by dusts lodged inside lungs. Extensive epidemiological investigations conducted on miners from different coalmining districts, where equivalent dust exposures have been shown to result in vastly different frequencies of lung disease incidence, also confirm this hypothesis (1) In a recent study, Ferrer et al. (2) used energy-dispersive X-ray analysis (EDXA) to investigate the inorganic element content in pleura and lung in reference, silica exposed non-pneumoconiosis, and silicotic populations. Constant depositions of silicon and calcium were detected in visceral pleura, parietal pleura, and lung of the refence group and in visceral pleura and lung of the exposed non-pneumoconiosis and silicotic groups. Comparison of the silicon content in pleura between silicotic and exposed non-pneumoconiosis subjects showed a nonsignificant probability of difference, whereas there were no differences with respect to the silicon content in lungs."

Dec 1, 1995

By H. R. Wells

The Blackbird district, Lemhi County, Idaho, has long been recognized as a potential source of cobalt and copper. However, the comparatively low grade and small size of the known ore bodies, the small demand for cobalt, and. the lack of adequate roads throughout the region precluded extensive exploration of the early discoveries in the area. Recent advances in alloy metallurgy, accentuated by wartime activities, greatly increased the demand for sources of domestic cobalt. Beginning In 1941, engineers of the Bureau of Mines conducted an examination and exploration program in the Blackbird district. This work was supplemented by an exploration program by engineers of the Howe Sound Mining Co., 730 Fifth Ave., New York 19, N.Y.

Jan 1, 1948

By N. Kyriazi

A performance study of oxygen self-rescuers from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested a an breathing and metabolic simulator in the Life Support laboratories of the Bureau of Mines. Parameters monitored during the testing were inhaled levels of C02 and 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60- min man-test 4, as described in 30 CFR 11H. Results presented include ;apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1984

By D. W. Bridges, L. Crocker, R. O. Dannenberg

About 95 pct of the beryllium was dissolved from most ore samples by agitation leaching with 600 lb of H2SO4 per ton of ore for 24 hours at 65 ° C and 35 pct solids . Leach slurries generally were viscous , and the limiting pulp density for thorough mixing was about 35 pct solids . Settling of the leached pulp required 0.6 to 0.8 lb of a polyacrylic flocculant per ton of ore leached with 600 lb of H2SO4 per ton , whereas ore leached with 800 lb of H2SO4 per ton required only 0.2 to 0.3 lb of flocculant per ton . Terminal densities of the settled pulps were about 28 and 35 pct solids , respectively , from leaches using 600 and 800 lb of H2SO4 per ton . Vacuum filtration of settled pulps at 15 in . Hg resulted in a filter cake containing 50 to 59 pct solids . Roasting the ore at 500 ° C before leaching increased the limiting pulp density for effective mixing to 50 pct solids . Acid requirements , however , were not diminished , although leaching roasted ore with 600 lb of H2SO4 per ton resulted in densification of settled pulps to about 40 pct solids . Filter cake from leaching preroasted ore contained about 20 pct less water than that from unroasted ore .

Jan 1, 1963