Search Documents

By Gerald W. Elger

The Federal Bureau of Mines developed a modification in the conventional Kroll process for preparing high - purity hafnium metal . This modification involved the partial replacement of magnesium by sodium in the batch reduction of purified hafnium tetrachloride to sponge metal . The raw tetrachloride was purified either by thermal degassing of the volatile contaminants to the atmosphere or by fused- salt treatment . In the fused- salt treatment , the tetrachloride was contacted with molten alkali chlorides to remove the impurities . The reaction byproducts were removed from the metal by heat treatment in an evacuated furnace . The metal sponge was consolidated by melting into buttons or ingots , which were analyzed for impurities . The purity of the metal prepared by the modified process is superior to that of the metal produced by the conventional method . The hafnium metal was comparable to crystal - bar hafnium except for the oxygen content , despite the abnormally high impurity concentrations in the raw tetrachloride . Several ingots were successfully cold - rolled to sheet .

Jul 1, 1960

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By James H. Gary

Data regarding the composition and physical properties of Florida land-pebble phosphate-waste slime are presented, and the feasibility of dewatering and beneficiating the slime by several different methods is discussed. Chemical analyses, electron micrographs, and X-ray diffraction data showed that principal constituents of the slime included quartz, attapulgite, and flaorapatite. Viscosity of the slime changed with pH; thixotropic, Newtonian, and rheopectic states were observed as the pH increased. Use of various flocculating agents was not effective in improving thickening properties of the slime. Dewatering tests using pressure filtration showed that temperature influenced the filtration rate more than pressure; the filtration rate at 165° C was tenfold that at room temperature. Selective flotation of the slime, using two different processes, gave promising results. About 25 pct of the phosphate was recovered in a concentrate assaying 31 pct P205, Other tests demonstrated that the slime could be successfully fractionated at 20-microns using a hydrocyclone. In hydrometallurgical tests about 80 pct of the phosphorus and alumina were chemically extracted from the slime using sulfuric acid. Limited bacteriological studies made of the slime showed that several types of microorganisms were present and grew in the material despite the presence of fluorine-bearing minerals.

Jan 1, 1963

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942

By A. W. Deurbrouck

Five preparation plants employing concentrating tables for washing 3/8- inch to 0 raw coal were tested. Two of the plants were washing Pittsburgh-bed coal, two were washing Pocahontas-bed coal, and one was washing Elkhorn-bed coal. Samples of the feed to and products from the tables were collected over the normal operating shift. These samples were analyzed, and complete performance criteria were determined. The results of this study show that the concentrating table is an effective fine-coal cleaner even when operating at 40 percent over the recommended 10 tons per hour feed rate. Recovery efficiencies for the 3/8-inch to 200- mesh size fraction ranged from 97.3 to 99.3 percent; maximum yield errors and ash errors were 2.4 and 1.0 percent, respectively; probable errors ranged from 0.074 to 0.115 specific gravity units and error areas from 52 to 73 square centimeters. The amount of minus 200-mesh material in the water used for feed water and dressing water to the table had no significant effect on the sharpness of the separation achieved but did have an effect on the ash content of the clean- coal product. In the one plant studied, the substitution of fresh water for plant circulating water reduced the ash content of the clean coal by about 6 percentage points.

Jan 1, 1963

By A. R. Mumford

During the course of an investigation conducted by the fuel section of the Bureau of Mines , on a hand- fired return- tubular boiler plant , it was found that the average cost of fuel to produce 1,000 lb. of steam was $ 0.5287 . Tests conducted after some simple changes had been made in the furnaces , and in the control of the boilers , showed the previous high cost of fuel per 1,000 lb. of steam could be reduced to the reasonable figure of $0.3540 , or the equivalent of over 30 per cent saving in fuel cost .

Mar 1, 1923

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

1. A total of 14,413 mining operations reported employment to the Mine Safety and Health Administration (MSHA). Nearly half (48.9%) were sand and gravel operations, followed by stone (28.5%), coal (14.7%), nonmetal (5.7%), and metal mines (2.1%). 2. Mine operators reported 240,000 full-time equivalent workers1 (down 3.9% from 1999). Independent contractors reported 42,000 full-time equivalent workers working on mine property (up 8.6% from 1999). Coal operators accounted for 26.8% of reported employee hours, followed by stone operators (25.9%) and sand and gravel operators (12.1%). 3. Eighty-four (84) work-related mine fatalities occurred in 2000 compared to 90 the year before. •The mine fatality rate was 29.8 per 100,000 full-time equivalent workers compared to a fatality rate of4.6 per 100,000 employees for all private industry. •Thirty-one percent (31%) of the fatalities occurred in underground work areas, which account for only17% of total employment. •Although the largest number of fatalities (28) occurred among miners who work for coal operators, coal contractor employees had the highest fatality rate (61.1 per 100,000 full-time equivalent workers). 4.There were 10,839 nonfatal lost-time injuries reported to MSHA, occurring at a rate of 3.8 injuries per 100full-time equivalent workers, and resulting in a total of 417,918 lost workdays.2 •Among all employees,3 the highest injury rate occurred among coal operator employees (5.6 nonfatal injuries per 100 full-time equivalent workers). •The highest percentage (34.7%) of nonfatal lost-time injuries were due to handling materials (e.g., over-exertion in lifting, pulling, or pushing objects), which also accounted for the greatest percentage of lost workdays (29.3%). •Among the most frequently occurring injuries, the most severe (as measured by the median number of days lost) were associated with accidents involving falls of ground, the use of powered haulage, and slips or falls. •The most frequently reported part of the body injured was the back (22.9% of all injuries). Back injuries accounted for the highest percentage of lost workdays (21.6%). 5.Seven hundred sixty-seven (767) cases of occupational illness were reported to MSHA. •The most frequently reported illness was repetitive trauma, resulting in joint, tendon, or muscle inflammation or irritation (37.3%). •There were 155 (20.2%) illnesses reported as hearing loss. The majority (68.4%) of hearing loss cases occurred among surface workers. •Coal workers' pneumoconiosis accounted for 14.5% of reported illnesses.

May 15, 2002

By W. K. Collins

Engineered scavenger compounds (ESC's) developed by the U.S. Bureau of Mines are a novel class of compounds that selectively can recover a desired element from a solid or molten alloy. Lithium titanate (L2Ti307 or Li2O?3Ti02) is used as an ESC to recover lithium (Li) from aluminum-lithium (Al-Li) alloys. X-ray diffraction measurements have shown that Li2Ti307 undergoes a phase change during scavenging from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of lithium in the matrix of the material and the effect of temperature. Although both phases are metastable, the hexagonal phase that forms during the scavenging of lithium from Al-Li alloys appears to be the more stable phase. Recovering lithium from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. The orthorhombic and the hexagonal structures of Li2Ti307 have similar scavenging capacities for lithium. This report proposes a new mechanism for the phase transformation.

Jan 1, 2010

By H. G. Iverson

Solid state reactions of manganese with silica were investigated in high-temperature tests. Reactions of 0.5 to 4.0 moles manganese (Mn) with 1 mole silica (SiO2) at 1,100° C and of 2.0 Mn:SiO2 mole-ratio mixtures at 1,000° to 1,150° C yielded products consisting of a slag phase and a metallic phase. At 1,100° C, the slag phase from reactions of the low Mn:SiO2 mole-ratio mixtures was composed of SiO2 and rhodonite (MnSiO3), and the slag phase from the high Mn:SiO2 mixtures was composed of MnSiOs and tephroite (Mn2SiO4). The metallic phase from the corresponding low Mn:SiO2 mole-ratio reactants consisted of two manganese silicides, Mn5Si3 and Mn3Si; from the high Mn:SiOg mixtures, it was Mn and the manganese silicide (Mn5Si). For the higher mole ratios of MnSiO2 the manganese content in the metallic phase increased, while the manganese and silica contents of the slag phase remained nearly constant. The slags did not contain free or uncombined manganese oxide (MuO). For the 2.5 to 4.0 Mn:SiO2 mole-ratio mixtures reacted at 1,100° C, the maximum quantities of silica reduced and of the manganese in the slag appeared to become asymptotical at about 41 and 48 percent, respectively. A brominating procedure was developed that was highly selective in removing the metallic constituents from the reaction product, leaving the slag phase as residue. X-ray diffraction patterns were obtained on prepared silicides Mn5Si, Mn3Si, and MnSi.

Jan 1, 1967

By ALICE V. Petar

Thallium is one of the rare metals that has come into commercial use within recent years . Its comparative scarcity , combined with a resemblance to the common metal lead , have retarded the development of uses for thallium . Although production is still measured in pounds rather than in tons , it is now finding application in a number of fields . Perhaps the earliest commercial use of thallium was as a constituent of optical glass of higher refractive power than similar glasses containing lead . One of the later applications to attract attention was the use of the oxysulphide in a sensitive electrical device similar to the selenium cell . The " Thalofide " cell , which was patented in 1919 , constituted for a time the most important outlet for thallium. During the next few years the limited use of thallium and its salts in other fields was insufficient to absorb an annual production of a few hundred pounds , and the price dropped from $ 16 or $18 per pound in 1922 to $ 5 per pound in 1924 . Beginning in 1925 several new uses were developed , especially as a poison for rodents and ants , and as a result the demand for thallium increased sufficiently to cause a recovery in price to the present level of from $12 to $15 per pound .

Jun 1, 1931

By P. A. Bloom

Bureau of Mines research was conducted to develop effective separation methods that might be used in exploiting substantial tonnages of complex barite-fluorspar ores in Arizona. The exploitable reserves now may be increased as recent batch and continuous flotation tests demonstrated that a complex barite?-fluorspar ore from the Red Chief deposit, Yuma County, Ariz., could be selectively treated to concurrently produce (1) fluorspar and (2) a barite byproduct of marketable grade. The sample contained 24.8 percent CaF2 and 24.3 percent BaS04. Processing comprised production of a fluorspar product containing 97 percent CaF2 with an 82 percent recovery, using a sodium fluoride-lignin sulfonate-fatty acid reagent combination. Concurrent retreatment of the fluorspar tailing, using sodium cetyl sulfate as a collector, yielded a barite product of 94 percent BaS04 grade with a 71-percent recovery. The products met specifications for acid-grade fluorspar and drilling mud-type barite.

Jan 1, 1963

By R. V. Higgins

This paper describes a method and a computer program for calculating shape factors and areas of channels that turn more than 90° and conduct fluids into the backs of wells. The program represents an improvement over a previous Bureau of Mines investigation by using a 4-point Lagrange interpolation equation instead of a 3-point and by summing areas of trapezoids with either x altitudes or y altitudes. Some of the techniques reported in this paper can also be used to compute the areas between contours and the lengths of lines that turn more than 90°.

Jan 1, 1968

By L. C. Brichta

During a study of the Badger-Peacock area from October 1950 to June 1953, the Federal Geological Survey and the Federal Bureau of Mines completed nearly 98 miles of resistivity profiling and drilled 96 test holes aggregating 17,628 feet of bore, In addition, seismic profile measurements were made along 8 traverse lines for an aggregate length of about 16,600 feet. The geophysical surveys were conducted by the Geophysics Branch of the Geological Survey; the drilling was done by the Bureau of Mines. Electrical-resistivity measurements disclosed 21 low-resistivity anomalies and 1 high-resistivity anomaly. Correlation of the resistivity data with the geological information revealed by the drilling disclosed that the low-resistivity anomalies indicated either slumped shale deposits in limestone sinks or undisturbed deposits of shale lying in erosional depressions in the limestone. The high-resistivity anomaly indicated hard, undisturbed limestone at or near the surface.

Jan 1, 1958

By W. M. Traver

During World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for exploration included those expected to contain metals of importance in the successful prosecution of the war. This report describes exploration of a district of known antimony occurrence on Coyote or Antimony Creek near Antimony, Garfield County, Utah. A preliminary report by Paul T. Allsman, Chief of the Bureau's Salt Lake City branch made in August 1941, recommended further investigation, and proposed methods for performing the work. The project, begun in November 1941 and completed in January 1942, included trenching and sampling in four of the most promising parts of the area The Federal Geological Survey cooperated in the work by detailed mapping and assisted in the interpretation of geologic data.

Jan 1, 1949

By N. H. Darton

In mining coal in the anthracite region of Pennsylvania the general custom has been to leave a large percentage of the coal in place as pillars to support the roof. Evidently any practice that involves partial waste of an important mineral resource is bound to be discarded. It is well recognized that one method of obviating probable waste is to fill the workings with cheap or worthless materials, a process extensively employed in the anthracite and some European mines. At present many of the collieries in the anthracite region of Pennsylvania are utilizing refuse from the old culm banks, which formerly were prominent features in the landscape, and are flushing the fine waste underground so that pillars may be reduced in size or removed. As a result the banks are now disappearing and soon will be gone. The fine culm from the breakers and rock from the mines will continue to be available, but the volume of these materials is insufficient to replace any considerable proportion of the coal removed. The next stage of progress suggested is the use of sand. Fortunately there are available large deposits of this material, much of which can be handled by dredges and pumps. This report is issued by the Bureau of Mines in the interest of safer and more efficient mining methods. I ts purpose is to describe the sand deposits in the northern anthracite coal field in Luzerne and Lackawanna Counties, Pa, Much of the information available is presented in the map, Plate I. Field studies, mostly preliminary, were made in the summer of 1911 to determine the distribution, amount, and character of the larger deposits. It was not thought desirable to make a detailed examination of the region because when the coal companies decide to utilize the sand their engineers will make precise surveys and drill test holes. In preparing the map the various coal companies were consulted; they contributed a large number of facts, especially as to the deposits in the buried valley of the Susquehanna between Pittston and Nan- ticoke, where nearly 1,000 test holes have been bored. The results of these borings were placed at the author's disposal, and have been utilized in drawing the boundaries given in the wide valley area and its extensions up Lackawanna River and NewportCreek. Wyoming Valley contains deposits of sand that are 100 feet thick over a wide area, 200 feet thick in places, and over 300 feet thick in the deep old channel south of Plymouth.

Jan 1, 1913

By A. M. Evans

"INTRODUCTION Exploration of the Iron Mountain and Bader iron-ore deposits in Llano County and the Gamble deposit in Mason County, Texas, was begun by the Bureau of Mines in January and completed in May 1944. The deposits had been examined by A. B. Needham, district engineer of the Bureau, in November 1942. Detailed geophysical studies by the gravity method as well as with a dip needle were made by the Bureau of Economic Geology 3/ of the University of Texas and the Federal Geological Survey. 4/ACKNOWLEDGMENTSIn the program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy., It is the policy of the Bureau to publish the facts developed by each exploration project as soon as practicable after its completion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930