Search Documents

By W. H. Oppelt

The Federal Bureau of Mines investigated combustion of lignite in domes-tic heating equipment to obtain information on equipment performance and to evaluate testing procedures. Three types of domestic heating equipment were tested, ranging from a hand-tilled, magazine-type space heater to a ram-type overfeed stoker. Lignite was readily burned in each of the three units under various test conditions. Burnoff rates determined by adding weighed charges to the magazine were found to be in error because of shrinkage of the lignite when only a portion of the magazine capacity was consumed during a test. More reliable burnoff rates could be determined by carbon-nitrogen balances. A hand-fired magazine-type space heater (Booker heater) was operated without the furnace attachment at efficiencies to 75 pct. One test series was run with minimum supervision under conditions encountered in actual household operation. No mechanical trouble was encountered.

Jan 1, 1960

By Jack G. Croeni

The Bureau of Mines developed a method to extrude low-density tungsten powder billets into rods and sheet bar with high-energy-rate forming equipment. Billets were compacted and sintered in an atmosphere of hydrogen to obtain a density of approximately 60 percent. Extrusion was conducted at reduction ratios of 6.25 to 1 and 9 to 1 at 1,800° C to prod e high-density, sound material. Yield strengths obtained were higher than those of material produced by conventional powder-metallurgy techniques, but ductility was lower at high temperatures.

Jan 1, 1966

By H. G. Wolfhard

The mode of propagation of explosions through narrow passages is important for understanding flameproofed equipment employed in mines. Narrow channels have been used in this investigation that connected between a small explosion chamber and a large chamber containing fuel-air mixture. The oxygen index of the mixture in the small chamber was determined which caused an explosion in the outer chamber. Preliminary measurements have already been given in Bureau of Mines Report of Investigations 5457 and suggested that) flames do not pass through narrow channels. The hot, burned gases from the explosion in the small chamber, however, are able to ignite the mixture in the large chamber by a process of hot-gas ignition. Systematic measurements are reported in the present paper that cover the influence of channel length and diameter and the properties of the gas mixtures in the large chamber on the transmission of explosions. The influence of such properties as quenching diameter and flame temperature is also discussed. This paper concludes the work on this problem and presents a theory that describes in detail parameters that influence transmission of explosions through narrow channels. INTRODUCTION Flameproofed equipment in mines is usually provided with flanges. A gap between the opposing flanges allows ventilation and release of pressure. The safe gap width has been determined for a number of flange lengths by Smith4/

Jan 1, 1959

By Thomas J. Peters

The King Mountain study area is centered about 120 air km northwest of Blackfoot, and 30 air km north of Arco, Idaho. The study area makes up the southern one-third of the northwest-trending Lost River Range--the highest mountain range in Idaho. The area is predominantly underlain by Paleozoic-age marine limestone and lesser dolostone, with a relatively small inlier of silica-rich, Ordovician-age quartzite. There are vast, unquantified resources of these industrial minerals present; however, special markets need to be developed for these resources which are near enough for transportation costs to be competitive. Five prospects were found in the study area; however, only one, the Elbow quartz silica prospect, contains resources and current claims. There has been no mineral production in the study area.

Jan 1, 1993

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC). Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-431' the semiannual reports were resumed.

Jan 1, 1950

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

By P. G. Clites

The Bureau of Mines developed techniques for induction melting of titanium in a split, water-cooled copper crucible. Calcium fluoride, which was used as an inert slag cover during melting, formed an insulating layer of solid slag between the ingot and the crucible wall. This thin layer of slag effectively insulated the ingot from the crucible and prevented the molten metal from shorting across the slits between adjacent segments of the crucible. The technique provides a means of melting loose titanium sponge and scrap and eliminates the need for fabricating a consumable electrode. This report describes the equipment developed and compares ingots produced from two varieties of titanium sponge, from titanium scrap, and from previously melted titanium with ingots prepared by vacuum-arc melting and electroslag melting. A melting scheme was also proposed and evaluated whereby loose titanium sponge was consolidated into a first-melt ingot for vacuum-arc remelting.

Jan 1, 1969

By Wilder D. Foster

In the method used in the Health Branch of the Bureau of Mines for petro-graphic identification of the minerals in a rock, the sample is crushed, ground to a fine powder in a mortar, the powder is put on a slide, a drop of index oil and a cover slip are added, and the slide is ready for examination. The rock should be ground fine enough so that most of the particles consist of only one mineral, otherwise identification is difficult. Finally, the amounts of the minerals present in the sample are estimated to the nearest 5 or 10 percent. When quartz grains are mixed with some claylike minerals) of which by far the most common example is quartz and kaolinite in a shale, grinding in a mortar does not always separate the quartz from the kaolinite; instead, the quartz grains become coated with the kaolinite and are not visible, even after careful search. Talc acts Similarly, but muscovite and pyrophyllite do not. In evaluating the possible silicosis hazard of breathing dust from a shale, it is essential to be able to see and identify all of the quartz grains, as the other minerals present are relatively innocuous.

Jan 1, 1949

By D. B. Taliaferro

[Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Core specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of tae subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, "connate" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and availability of oil and gas within a reservoir and in devising, efficient means for their withdrawal.]

Jan 1, 1939

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

To provide longwall operators with a method to predict methane emissions from panels with increased face width.

Jan 1, 1997

By D. G. Foot

The Bureau of Mines investigated two methods for recovering potash from carnallite ore in continuous 100-lb/h flotation units. In the insoluble-slimes flotation procedure, insoluble slimes were removed by flotation prior to potash flotation. In the direct flotation method, insoluble slimes were depressed and the potash floated directly without prior removal of the insoluble slimes. Seventy-three percent of the potash in the ore was recovered in a leached final KCl product contain-ing 59.1 pet K20 using the insoluble-slimes flotation method. The direct flotation method recovered 74.5 pct of the potash in a final product containing 60.2 pet K20. The rate of return on the investment was calculated at 13 pct for the insoluble-slimes flotation method and 15 pct for the direct flotation method, based on a Bureau economic evaluation.

Jan 1, 1984

By Roy E. Peterson

The Bureau of Mines has been developing and evaluating methods for beneficiating the large deposits of nonmagnetic (oxidized) taconite located on the western Mesabi Range. In this segment of the research, a sample representing about 0.5 billion tons of nonmagnetic taconite from near Grand Rapids, Minn., was beneficiated using a reduction roasting, magnetic separation, flotation process. The sample contained 32.1 pct iron and 49.1 pct silica. Tests were conducted both on a bench scale and with a 1,000-lb/h pilot plant. In the bench-scale research a con-centrate containing 69.0 pct iron and 4.5 pct silica was produced with an iron recovery of 82.1 pct. In the pilot plant, reduction roasting was conducted in a 35-ft kiln using lignite as the reductant and major source of fuel. Dust from the kiln exhaust was pelletized and recycled to the kiln. The roasted taconite was beneficiated by magnetic sep-aration and flotation to produce a product containing 67.9 pct iron, 5.5 pct silica, and 69.7 pct of the iron in the kiln feed. The cyclone separation in the grinding circuit was sharpened by demagnetizing the cyclone feed in a 400-Hz, 1,000-Oe magnetic field.

Jan 1, 1983

By Joe B. Rosenbaum

New applications and concepts of solvent extraction as a unit operation in extractive metallurgy have been developed in the last decade. Wider use is being made of established solvent extraction techniques in processing spent nuclear fuel elements and in winning columbium-tantalum, hafnium-zirconium, thorium, tungsten, uranium, and vanadium. Commercial application has been extended to recovery of beryllium, boron, bromine, copper, molybdenum, phosphorus, rare-earth metals, and rhenium. Systems in use and proposed typically extract metals or salts as anion, cation, or neutral species from aqueous media by reaction with a recycleable organic reagent.

Jan 1, 1971

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By R. H. Fewkes

New information on possible resource value of sea floor manganese nodule deposits in the eastern North Pacific has been obtained by study of records and collections of the 1972 Sea Scope Expedition. Nodule abundance (percent of sea floor covered) varies greatly, to judge from bottom photographs from 8 stations and data from other sources. All estimates considered reliable are plotted on a map of the region. Similar maps show the average content of Ni, Cu, Mn, and Co at 89 stations from which 3 or more nodules were analyzed. Variations in nodule metal content at each station are shown graphically in an appendix, where data on nodule sizes are also given. Results of new analyses of 420 nodules from 93 stations, for Mn, Fe, Ni, Cu, Co, and Zn, are listed in another appendix. Relatively high Ni+Cu content is restricted chiefly to four groups of stations in the equatorial region, where group averages are 1.86, 1.99, 2.47, and 2255 weight percent. These and a few other areas may warrant more exploration. It is hoped that this report will stimulate new interest in North Pacific nodule deposits and that the maps and quantitative data will aid future exploration.

Jan 1, 1981

By James Paone

This report on the state of the art of horizontal boring technology for underground power transmission installations was prepared by the Bureau of Mines at the request of the Department of the Interior. This paper describes the different machines and methods used in augering, impacting, pushing, drilling, and machine tunneling horizontal holes through soil and rock. A review of the borehole survey and guidance tools and techniques applicable to these methods is also given. Nonboring methods used for emplacement of power distribution and transmission lines are briefly discussed. The paper ends with a brief technical forecast, an analytical summary of the state of the art, and recommendations based on power industry needs. Horizontal boring techniques for power distribution lines installation are adequate to meet the requirements of the power industry, particularly where such burial involves relatively short distances in soil or soft rock. For burying power transmission lines, particularly in the harder rocks and over relatively long distances, horizontal boring methods are not as well advanced. Research and development as well as economic incentives to equipment manufacturers could substantially improve the state of the art. Obstacle detection and guidance systems for directing boreholes to specified targets need major improvements to meet the requirements of the power industry for underground burial of distribution and transmission lines

Jan 1, 1968