Search Documents

By M. Hertzberg

The Bureau of Mines measured the energy requirements for the spark ig-nition in air of Pittsburgh seam bituminous coal dust, lycopodium spores, and polyethylene powder with a 1.2-L furnace and 8-L and 20-L chambers. Thermal autoignition temperatures of the same dusts were mea-sured in the 1.2-L furnace. Electrical ignition requirements are given in terms of both effective spark gap energies, [ ] and stored circuit energies, 1/2 CE2. The measured order of electrical ignitability for the three dusts is consistent with the data of other researchers; however, the absolute values are systematically higher, probably because of higher flow and turbulence levels in the chambers used and lower electrical efficiency in the circuit used here. The temperature dependence of the lean limit of flammability for lyco-podium was measured wi th the 1.2-L sys tem, and those measurements con--firm the applicability of the modified Burgess-Wheeler law to a dust. Due to experimental complexities, the minimum ignition energies for dusts may not reflect intrinsic flammability behavior. However, some valuable information may be obtained from the relative ignition energies of various dusts at ambient and elevated temperatures. In addition, the concept of minimum electrical ignition energies for homogeneous gas mixtures is reevaluated theoretically.

Jan 1, 1985

By Everett P. Partridge, J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decrease this to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the kraft-paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and the anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2 504 • 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of the total weight of the crude salts and therefore has a very important influence on transportation costs, in many instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery of production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.

Mar 1, 1936

By d&apos, D. V. Andrea

Nine rock properties were determined for rocks coming from 49 locations and having a wide range of compressive strengths. Plots of the nine rock properties versus each other were prepared. A stepwise multiple linear regression analysis was performed to obtain several equations for predicting compressive strength. Both linear and curvilinear relationships were assumed between compressive strength and the other rock properties. The prediction equations had multiple correlation coefficients ranging from 0.947 for an equation with 1 variable (point load tensile strength) to 0.986 for an equation with 25 variables. Of the properties tested only point load tensile strength could be used alone to estimate compressive strength with fair accuracy.

Jan 1, 1965

By Edward B. Kendall

[This paper is one of a series being prepared far and published by the United States Bureau of Minus describing the methods of mining used and operating costs obtained in producing land and gravel from deposits throughout the United States. This circular describes operations at the Eliot plant of the Pacific Coast Aggregates (Inc.). in Livermore Valley near San Francisco, Calif. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production posts. It is recognized that publication of total costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

? CAGER, CAGE RIDER, CAGE TENDER, SHAFT MEN All of the above job titles are variously associated with the handling of men and material at hoist stations. Generally, these classifications of personnel are involved with riding cages with personnel and in hoisting supplies into the mine. Job titles and activity description will be defined in the respective chapters. ? FLOW CHART SYMBOLS [Vertical Transportation Horizontal Transportation Storage Operation Delay ]

Jan 1, 1975

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

By Robert E. Wood

The compressibility factors, Z, of helium, nitrogen, and helium-nitrogen mixtures in the three-dimensional space of temperature, pressure, and gas composition have been related to the Leiden form of the virial equation of state. The dependency of virial coefficients through the fifth on temperature and gas composition has been established for the temperature range 133.15° to 748.15° K. Compressibility factors, Z, have been computed from the equation of state and tabulated as functions of gas composition, pressure, and temperature. Tabular values of Z are presented for 30.00 through 100.00 percent helium for temperatures from 240° through 700° R for pressures from 14.696 through 3,050 psia and for temperatures from 720° through 1,300° R for pressures from 14.696 through 1,500 psia. Tabular values of Z are presented at increments of 5.00 percent helium and 20° R, and, for pressures greater than 50 psia, at increments of 50 psi.

Jan 1, 1967

By K. R. Dorman

To develop the potential of precast concrete sets as a support medium in underground mines, a three-piece precast concrete drift set was designed for a small opening and tested to destruction in an underground straining frame. Thirty-six tests were made with three sizes of members using three different loading conditions. In addition, 14 members were tested individually in the laboratory. Test results are compared with theoretical calculations. A cost comparison shows the use of concrete sets would be advantageous where conventional wooden timber requires excessive replacement.

Jan 1, 1968

By D. W. Bridges, Donald R. Peterson, Masami Hayashi

Techniques are described for recovering about 80 pct of the cobalt and nickel contained in superalloy scrap by anodic dissolution of the scrap and simultaneous electrodeposition of a pure cobalt - nickel alloy at the cathodes in an electrolytic cell partitioned by permeable diaphragms into separate anode and cathode compartments . Superalloy scrap was alternatively prepared for subsequent anodic dissolution either by melting and casting massive scrap into suitably sized anodes , by packing moderate - sized discard scrap in inert metal baskets that subsequently served as anodes , or after concentrating the superalloy portion of grinding debris , by magnetic separation to reject corundum or other abrasives , slagging any remaining abrasives from molten grindings , and finally casting the superalloy metal into anodes . In the processing , purified electrolyte -- 1 N in NiSO4 and in NiCl₂ , and 0.1 N in CoSO4 and in CoCl2 --was charged to the cathode compartments and discharged from the anode compartments at a rate sufficient to overcome the backward migration of ionic impurities from the anodes to the cathodes . Discharged electrolyte was purified by reacting it first with SO2 and next with limestone , and then recirculated to the cathode compartments , in which a 50 pct cobalt - 50 pct nickel alloy was deposited on either blanks of stainless steel or starting sheets of cobalt - nickel alloy . The process was made self - sustaining by either adding H2SO4 to the catholyte feed to throttle the rate of cobalt - nickel deposition , thereby compensating for the slower rate of cobalt - nickel dissolution from the anode and losses occurring in electrolyte purification , or alternatively , adding H₂SO4 to

Jan 1, 1964

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

1. In 2002, a total of 2,820 contracting companies reported employment at coal mines to MSHA.

Jan 1, 2004

By W. Hermanson

This report presents the results of a task to complete a final design of a remote controlled hi-roof bolting machine for high roof areas in coal mines. The project was begun by visiting several coal mines to become familiar with roof fall areas. Several machine concepts were generated and presented to the design committee for criticism. A preliminary design was completed, as covered by this report. A Final Design and Final Report will be issued incorporating the committee comments at the Preliminary Design review and comments received concerning this Preliminary Design Report.

Jan 1, 1979

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978

By John Nagy

Large-scale tests in the U.S. Bureau of Mines Experimental Coal Mine show that the explosion hazard of coal dust on shuttle-car roadways can be con-trolled by proper application of water, dry rock dust, a saturated solution of ammonium phosphate, or mixtures of water or the water-phosphate solution with rock dust. The experiments were made with loadings of 1.0 and 5.0 pounds of mine size coal dust per linear foot of entry, and with a 3-or 4-inch-thick layer of coal rubble on the floor, The data from the tests with mine-size coal and rubble are comparable. The water contents of the dust loading were determined from samples collected just prior to initiation of a gas-air mixture in an ignition zone at the face Dust samples were collected 1 inch deep from the coal-rubble deposit. One experiment was made with the dust in the coal rubble bound with latex applied as a water solution by spray. The binding action was inadequate and explosion propagation was obtained.

Jan 1, 1970

By William W. Adams

A general increase in employment prevailed in the stone-quarrying industry of the United States during 1941 compared with 1940. Likewise, more accidents occurred to men working in and about the quarries, with the result that the accident-frequency rate for the industry as a whole was higher in 1941 than in the previous year. Reports from operating companies to the Bureau of Mines, covering open and underground quarries, as well as rock-crushing and rock-dressing plants, cement mills, and limekilns at or near the quarries, showed a total of 86,123 men employed and a total of more than 22 million man-days of labor performed during 1941. The total working time of the industry averaged 260 days per man. Measured in man-hours, the volume of work equaled 173 million, an average of 2,011 man-hours per employee.

Jan 1, 1943

By John C. Machisak

The thirty-fifth consecutive National Safety Competition sponsored and conducted annually by the Federal Bureau of Mines, Department of the Interior, closed with several noteworthy accomplishments to its credit. Some of them are: 1. A record low injury-frequency rate of 18.293 disabling work injuries per million man-hours equal to that established in 1957. 2. The third lowest injury-severity rate (4,335). 3. The second highest number of mines and quarries participating (672) 4. A record number of participants finishing the competitive year without a disabling work injury. 5. All recipients of Sentinels of Safety trophies free of disabling work injuries for the first time since 1952.

Jan 1, 1961

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By Seth T. Reese

THE INJURY and related employment experience of the coking industry in the United States for 1953 contained in this bulletin are presented under three general sections, as follows: (A) General injury experience: Tables 1 to 9: Contain current and comparable statistics on operating data, number, frequency, and severity of injuries, and major accident agencies involved in the cause of injuries. Data are tabulated for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data covering 5- and 10-year periods on the number and severity of injuries and major accident agencies. (C) Historic injury experience: Tables 1.6 to 19: Contain data on the number and rates of injury occurrence and related employment statistics on the industry from the earliest records through 1953.

Jan 1, 1955

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964