Search Documents

By M. E. Volin

The Smuggler is one of the mines in the Aspen district, located the central part of Pitkin County, Colo. It was first examined in July 1943 by C. R. Wilfloy, former mining engineer of the Bureau of Mines at Salt Lake City, Utah, in, company with the lessees, R. D. Rohlfing of Aspen and J. W. Vanderwilt of Denver. The purpose of this examination was to sample a mineralized breccia zone that appeared continuous along the contact between the Leadville and Weber formations. These preliminary samples showed that the zone contains low but significant amounts of lead and zinc and that the minerals are partly oxidized and thus not easily concentrated. The mine was examined again in May 1946 by the senior author and William Herron, one of the present lessees of the property. This examination reviewed the previous sampling and recommended investigations by the Bureau of Mines. Sampling and drilling investigations were conducted by the Bureau from October 1946 to February 1947 and again from August 1947 to April 1948. Aspen is the center of a famous mining district that produced over $102,000,000 in silver and lead ores from 1880 to 1918, when a dispute closed down the mines (fig. 1). All of the workings below the Cowenhoven tunnel in Smuggler Mountain and the lower Durant tunnel in Aspen Mountain have been flooded since that time. The Cowenhoven portal now is caved, and Smuggler Nos. 1 and 2 tunnels are the only accessible workings in Smuggler Mountain. The only operating mine is the Midnight, situated 4 miles south of town at an altitude of 9,700 feet.

Jan 1, 1950

This report briefly describes the broad program of research and technologic work conducted by the Bureau of Mines on coal and related subjects during 1966. In addition to n description of investigations on mining, preparation, and utilization of coal, an account is given of the Bureau's work in mine health and safety, coal resources, mine explosives, and environmental conditions relating to coal mining and utilization. Details of most of the projects are reported in publications cited throughout this report. Centers and laboratories conducting the coal research and related investigations appear in appendix A; organizations, institutions , and companies contributing to the Bureau's coal research and technologic program are listed in appendix B.

Jan 1, 1967

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By E. J. Babcock, W. W. Odell

The Bureau of Mines since its establishment has always taken an active interest in the utilization of lignite and in the development of the lignite dep'osits of the United States. Extensive lignite fields occur in the west central States, notably in North Dakota, Montana, Wyoming, Colorado, and Texas; there are smaller areas in several other States, some of which are widely separated. The total area of the deposits and the total amount of lignite in these several districts are so enormous that the economic value is seldom recognized. To the people of ·the west and west central regions, however, the larger utilization of lignite, in whatever form it may be, is of fundamental importance, and any new methods or uses that promise to open these great lignite fields for more general and more efficient use deserve careful study. Although these lignite deposits underlie areas of thousands of square miles, their development and general utilization has been rather slow. This is no doubt partly because many of the districts are not thickly settled or highly developed in manufacturing industries, but is largely because lignites, from their peculiar physical and chemical characteristics, are low-grade fuels. Most of the lignites in these areas are imperfectly developed coals; many have a more or less woody structure; some belong to the brown-coal type; and others are darker, denser, and more homogeneous, approaching subbituminous coal. The people living in the regions in which these vast deposits occur, especially in the west central part of the United States, are vitally interested in every effort toward bettering lignite as fuel and aiding its wider utilization.

Jan 1, 1923

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By M. J. Ferrante

The preparation and subsequent reduction of vanadium trichloride was investigated as a process for the production of high-purity vanadium metal. Chlorine was reacted with vanadium oxide in the presence of carbon to vanadium tetrachloride. The contaminant vanadium oxytrichloride was also formed and later converted to tetrachloride by reaction with chlorine in the presence of activated charcoal. Vanadium tetrachloride was stirred continuously during thermal dissociation to vanadium trichloride powder from which volatile contaminants were removed by distillation. The vanadium trichloride powder was reduced to vanadium sponge by controlled feeding of the trichloride into molten magnesium. Excess reductant and byproduct salt were removed from the vanadium sponge by high-vacuum distillation. Batches as large as 6.5 kilograms of sponge metal were prepared at an average reaction efficiency of 98 percent. Vanadium sponge after consolidation by arc-melting contained 820 to 11330 ppm of interstitial impurities and had a hardness between Rockwell B 40 and 70, This metal exhibited excellent workability at room temperature. The purification of impure vanadium metal by electron-beam melting resulted in lowering interstitial impurities from 1,890 to 504 ppm and hardness from Rockwell B 87 to 28.

Jan 1, 1968

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

By Jennifer Riefenberg

A family of personal computer programs that calculate the Coal Mine Roof Rating (CMRR) has been developed by the U.S. Bureau of Mines. The CMRR rock mass classification system provides a link between the qualitative geologists' description of coal mine roof and the quantitive mine engineers' needs for mine design roof support selection, and hazard detection. The program CMRR is a user-friendly, interactive program into which raw field data are input. A CMRR is calculated and output along with two graphic displays. The first graphic display is a plan view trap with the CMRR's displayed on a color-coded scale. The second display shows a stratigraphic section of the bolted roof interval and its resultant CMRR. In addition, a Lotus 1-2-3 worksheet, computer file BOM-CMRR.WK3, has been developed for easy storage of field data. The worksheet includes four macros that automatically calculate CMRR's, store field test data in a database format, and print a two-page report of the field data and CMRR parameters. Production of summary port; for analysis of site-specific information are readily generated using Lotus 1-2-3 software. These programs help to facilitate the engineer in utilizing the CMRR in ground control studies.

Jan 1, 1994

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

Severe whipping of shuttle car trailing cables occurs when the car stops suddenly or reverses direction. This causes cable damage, and can seriously injure personnel near the cable. FMC has contracted with the U.S. Bureau of Mines to design, build and demonstrate a reel control system that will significantly reduce or eliminate whipping. II. CONCLUSIONS Results of engineering effort show that the following conditions are primarily responsible for the whipping problem. Causes may exist individually, or in combination.

Jan 1, 1972

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to consider able expense in testing such coals as may be available. In general it will always be possible to obtain a satisfactory coal or blend of coals for the particular purpose in view, but in some places the cost of transportation would be prohibitive. It may then be necessary to consider a coal or coals inferior in grade, rank, or both. At times, in fact, only one inferior coal may be available, when the problem becomes mainly one of selecting equipment and operating conditions best adapted to that coal, keeping in mind that the end product of the plant must compete with the imported product in the market the plant will serve. This applies particularly to new projects for which it is necessary to build a plant and start with a clean slate, so to speak. However, it will pay every coke-plant manager to employ a force to continually test the coals used and the coke produced to make sure that the quality is not changing appreciably. Furthermore, if the supply of coals used becomes exhausted it will be necessary to use other coals. Continual testing is particularly necessary at plants using borderline coals or blends, where slight changes in the composition or in operation of the ovens may render them dangerously expanding. In this connection it should be stated that control in the newer coke plants is considerably easier than for those built a decade or so ago, consequently in the new ovens a given operating program can be maintained more precisely. This point is important, because one of the main requirements of the coke user is uniformity in both physical and chemical characteristics. For example, any appreciable changes in the quality of coke delivered to the blast?-furnace operator will involve changes in operation if the best results are to be obtained. Such changes are expensive usually they take considerable time and involve production of inferior iron.

Jan 1, 1942

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a new methane analyzer system for underground applications. Methane enters coal mine ventilation air from the breakup of coal at the active face, from the collapse of roof rock during retreat mining, and from the ribs abutting virgin coal. Each source contributes varying amounts to the total emission, depending upon rate of mining, type of mining, and the character of the coalbed and adjacent strata. The evaluation of individual parameters of methane emission requires the continuous monitoring of individual mine sections over a long period of time. The methane analyzer system was developed to meet this need. The system has been installed and operated in an active mine in the Pittsburgh coalbed. The system and details of its installation and calibration are described. Data are presented to substantiate its reliability.

Jan 1, 1975

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July l, 1936.

Jan 1, 1940