Search Documents

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau's Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By Eric E. Cather

In 1984 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines conducted a mineral appraisal of the 315,000-acre Lemhi Range study area. This area is located in Lemhi and Custer Counties, about 25 mi south of Salmon, Idaho, and is in the Northern Rocky Mountain physiographic province, Topography is generally rugged with elevations ranging from 5,600 ft to about 11,350 ft above sea level. Since the 1880's, approximately 500 mining claims have been located within the study area; about 400 were current at the time of this investigation. Also, part or all of 12 patented mining claims are in the study area. During Bureau field work, forty-four mineralized sites were examined. The sites had been explored by 80 adits, 14 shafts, and about 140 pits and trenches. At least five properties in the study area have had significant production; the adjacent Mohawk, Grace Phelan, and Snowbird claims had a combined total of 136,000 oz of silver and 67,000 lb of lead; production at the Brown Bull was about 14,800 oz of silver and 115,000 lb of lead; the Portland mine yielded an unrecorded amount of silver. The Hilltop mine, located a few hundred feet outside the study area, produced 125,000 oz of silver, 2.7 million lb of lead, 87,000 lb of zinc, and 62,000 lb of copper from mineralized zones that might extend into the study area. More than 10,000 lb of copper were produced at the Blue Jay mine from workings located about 1,000 ft outside the study area. The Bureau of Mines investigation did not reveal the presence of identified resources in the study area. However, several areas contain mineralized sites and are known occurrences. Some of these warrant additional work to further delineate the mineralization and possibly determine identified resources.

Jan 1, 1988

By J. A. Kost

The objectives of this contract were to determine the amount, size, and deposition of float coal dust (74 x 10 microns) generated during the mining and transporting of coal in underground U.S. mining operations. Rock dust distributed by trickle dusters was also sampled. In addition to four belt-transfer points, two continuous and two conventional mining sections were sampled at five mines located in Pennsylvania, West Virginia, Kentucky, and Illinois. Float-dust samples were collected on deposition pans; total airborne dust was collected with MSA Model C personal samplers equipped with Unico filter casettes; Andersen cascade impactors provided relative size distributions of the samples. Production, airflow, and water flow were monitored to examine their effect on dust levels.

Jan 1, 1981

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By E. R. Maize

This report is the second of a series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company's Crucible mine, operating in the Pittsburgh bed in Greene County, Pa. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By J. R. Thoenen

[Before 1914 Germany held virtual monopoly on the world supply of potash for fertilizer purposes. During the world War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-time prices stimulated interest n various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany and other sources reduced prices to below pre-war levels, and, as a result, most of the domestic producers ceased operational.]

Jan 1, 1941

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li20-A1203-4Si02), a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Hills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade deposits in forth Carolina. The theoretical lithia (Li20) content of spodumene is 9.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934

By Damon C. Gray

This report contains a recommended program of acoustic research to be conducted by the U. S. Bureau of Mines. The program is directed toward the abatement and control of machinery noise in underground coal mining operations. The study conclusions and specific problem areas which led to the definition of the recommended program are also briefly described.

Jan 1, 1971