Search Documents

By W. Boas, R. Silva, D. Yumi, L. Steffen

The continuity of the flow and stages within the mining process is essential to achieve success in its operation and results, especially when it comes to a gold mine. During the first seven months of 2022, crushing at the Morro do Ouro Mine had 19 stops in the primary crusher due to equipment blockage/obstruction, this could be due to the size of the material that was blasted with explosives and fed. The feeding of coarse material to the crushing plant impacts the operation in several ways, for example, premature wear of the equipment, reduction in the supply of the remainder of the beneficiation, reduction of the buffer pile and damage to the conveyed belt. In a mine located far from the community, the fragmentation improvement is mainly related to load increments or some other relatively simple change. However, when it comes to a mine located close to communities, alterations of this type must be analyzed in detail, as it can have an impact mainly in relation to vibration and flyrock. Aiming to improve the efficiency of the blasting, mainly in relation to the result of fragmentation, a project was created to improve the efficiency of the blasting with a focus on reducing the crushing stoppage and reducing the amount of material discarded due to inadequate granulometry. During the evolution of the project, several improvement solutions were proposed, for example adjustment of the power factor in relation to the geological characteristics of the rock mass, drainage, blasting geometry, vibration reduction techniques and several operational improvements. By using the techniques and methods identified as improvements during the project, it was possible to observe and quantify improvements in relation to the fragmentation of the blast. During the months of January to July 2022 there were 19 events. It was estimated that at this rate there would be 14 more blockage events, but there were only 3 events and that meant a 79% reduction in blockage. In addition to the reduction in crushing shutdown events, there was also a 53% reduction in the amount of ore that is discarded due to inadequate granulometry and, with that, the feed rate of the grinding system was able to reach the maximum feed limit due to the material being fed to the mill well fragmented, contributing to increase the production and productivity of the beneficiation process at the Morro do Ouro Mine in Paracatu-Minas Gerais-Brazil.

Jan 1, 2024

By Evan Smart, Andrew Palangio, David Klingspor, Blessing Taiwo

This study presents a DMAIC-based approach to optimize blasting performance and achieve crusher-compatible fragmentation at the Walker-Severn Quarry in Ontario, Canada. By applying the Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) framework, the study aims to enhance the integration between blasting and primary crushing operations. Several representative blasts will be simulated and evaluated using both aerial and terrestrial image analysis technologies to assess fragmentation characteristics. The investigation was guided by quarry-specific Key Performance Indicators (KPIs), ensuring that blast design modifications were both practical and operationally relevant. Through structured analysis and data-driven refinement of blast parameters, the study reveals how this framework was used to address the quarry production demand for increased crusher throughput, and reduced processing costs. The existing quarry blast design was assessed as a baseline and compared against the crusher's inlet requirements and the acceptable fines level specified by the quarry. This evaluation aimed to identify and implement modifications to enhance blast performance. A drone (UAV) was employed to capture post-blast images and monitor blast pile displacement. These UAV images were used to generate an orthomosaic image, which was analyzed to assess fragmentation. The orthomosaic was overlaid onto a GIS platform using a 10m-by-10m grid to evaluate fragmentation distribution across the bench and identify areas requiring optimization. Additionally, drone imagery was utilized to monitor the impact of each blast on the subsequent blast's free face and to assess energy utilization for optimizing front-row holes to achieve improved fragmentation. The outcomes of this research offer a replicable methodology for continuous improvement in quarry blasting practices, with a focus on producing fragmentation that aligns with primary crusher requirements.

Jan 26, 2026

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Randy Martin, Jessie Bonner, Peter Boyd, Mark Leidig, Timothy Rath

We conducted the Vermont Damage Experiment in central Vermont during July 2008. Five single-hole explosions with yields ranging from 60.8 kg (134 lbs) to 122.5 kg (270 lbs) were detonated in homogeneous, low fracture density granite. The goal of the experiment was to quantify the different levels of rock damage around the source and then relate the seismic wave generation to the degree and distribution of damage and fragmentation. In addition, explosives with different velocities of detonation (VOD), including black powder (0.53 km/sec; 1737 ft/sec), heavy ANFO (4.8 km/sec; 15734 ft/sec), and COMP B (8.1 km/sec; 26574 ft/sec) were detonated to relate the VOD to seismic wave generation and extent of damage zones in the source region. Over 120 seismic stations were deployed to record the explosions at distances between 5 m and 30 km (15 ft to 19 miles).

Jan 1, 2010

By Robert Hopler

Complying with our request in the February issue of the AGRICULTURAL BLASTER for items that would be of interest to other blasters, Mr. Thomas H. Benton of Tennessee sends us an article in which his methods of securing contracts are explained:

Jan 1, 2013

By Dr. Anthony J. Konya

The modern era has seen a boom in virtual training platforms. This study details the effectiveness & applicability of online training in comparison to in-person training for the drill & blast industry.

Feb 1, 2020

By P A. Lang

Canada is constructing an Underground Research Laboratory as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in stable rock formations. Careful blasting methods have been designed and quality control procedures have been used for the excavation of the access headings in the underground facilities. This paper describes the work done between 1984 December and 1986 December at the second level, 240 metres below surface.

Jan 1, 1987

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of interactions by mining activity with an ever closer public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to predict and control vibration at neighboring structures.

Jan 1, 2013

By Matias Suarez, Diego Zenteno

It is known that the introduction of electronic timing in the sequencing of blasting has changed the vision and way in which mining is developed. It is possible to deal with more complex and sophisticated drilling designs, without compromising productivity or safety. It has been shown in various studies, that a correct timing of the blasting provides an improvement in the improvement of the processes downstream, due to a decrease in the resistance of the resulting fragments coming from the interaction of the waves generated in the detonation of explosive loads. On the other hand, it has also been shown that variations in the composition of a same type of explosive, has a significant influence over the resistance of the blasted material, also the energy associated to break it, affecting directly its degree of fragmentation. This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002). This study focused on the methodology of the formation and measurement of seismic pulses, through the rock massif. For this purpose, seismic pulses were acquired in the field and then, the different dynamic phases of the wave were molded mathematically, with the purpose of favoring the coupling between them.

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By Mario Alvarez

Drilling with tricone drill bits is widely used in the mining industry with a direct impact on drilling safety and costs, however it can be challenging to implement a new supplier of tricone drill bits, choosing a new model of this accessory due to the normal variations of the rock mass or even due to the acquisition of new and modern drilling equipment for open pit blasting operations. This article identifies the most common mechanisms of failure in productive drill holes of tricone drill bits, both in open-pit coal and metal mines, in two South American countries. It also emphasizes the important issues that must be addressed for the optimization of the performance of these accessories, such as the correct identification of the rock mass, the drilling parameters, and the impact of autonomous drilling on new equipment with this technology. The article presents some of the successful actions to economically improve the performance of drill bits considering the close relationship in the field with the supplier's technical representatives and factory designers, as well as the commercial interrelationship between their respective business areas. The article concludes by discussing the future of tricone drill bit design development, its environmental management, and possible new advances in its manufacture.

Jan 21, 2025

By Luan Monteiro, Francisco Biulchi

The AngloGold Ashanti - Cuiaba mine sought innovative approaches to minimize lateral development and stope extraction time while maintaining optimal gold recovery and minimizing dilution. The stope 8GAL EXT 30 was selected as a case study. Traditionally, conventional blasting methods in such a scenario would necessitate either a single mass blast or slot development at each end of the stope. These methods typically compromise recovery and dilution or increase development time and risk. Additionally, conventional wired detonators require workers to re-enter the stope between blasts to load blastholes and connect detonators. The wireless initiation system offers a solution by initiating blastholes using magnetic induction signals that can penetrate rock, air, and water. This technology allows a pre-charged stope to be mined without requiring workers to re-enter the area between blasts to charge and connect blastholes. Engineers from Orica and AngloGold Ashanti designed a new extraction sequence utilizing the wireless initiation system. The process began with the opening of one end of the stope using a conventional slot and wired electronic detonators. Subsequently, pre-loaded rings were fired in three blasts to extract the opposite end and the intersection. The 8GAL EXT 30 stope was successfully mined using this technology enabled method. Each blast was meticulously monitored, and the stope void was scanned to assess blast performance. The results demonstrated a 4.6% improvement in recovery and a 16% reduction in dilution compared to the initial plan, and reduced exposure of people to hazardous locations in the stope. These results represent an additional value of USD 200k, gained from implementing wireless initiation to enable this particular blasting schedule.

Jan 21, 2025

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By Jorge Cárdenas Miranda, Hector Espinoza

Currently in open pit mining in Peru with double bench, it is a challenge to optimize fragmentation in the drill rows near to the slopes to ensure the performance in the loading and haulage operation along with the process in the plant. That is why the present paper addresses a previously unanalyzed variable on the effect of the discontinuity plane on the fragmentation results. From the numerical mathematical models applied through algorithms in advanced computational tools such as Elfen, it was quantified the improvement in fragmentation results as P80 through a correct pre-split plane both in its extension as well as in its width. The first results show an improvement of 30% in the P80 and ensuring the quality of the walls without damage to the matrix of the final wall. The basis developed in this paper is based on the concept of wave reflection in the free face zones where greater efforts are presented for fragmentation, a similar theory is presented in the variation of initiation sequences that seek a greater area of reflective planes in the form of "V". Cases were evaluated with a percentage of compliance of the pre-split planes from 0 to 100% evaluating the impact on the results and correlated with field information explaining the behavior and validating the benefit. From the quantification of the benefits, this work opens the possibility of focusing resources on optimizing the pre-split process to achieve an improvement in the fragmentation results, giving a greater tool in the decision to optimize the blasting process.

Feb 6, 2023

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By Christoph Muller, Geoffrey Liggins, Mohan Hensman

Modern commercial blasting is as much a technical process as it is a business one. As with most processes both aspects of blasting are driven by and generate new data. The time-critical nature of commercial blasting in mining and construction projects, dictate the timely exchange of information so as not to impede production or commerce. Up-to-date information about the blast to be undertaken can help suppliers: meet customers’ expectations to address challenging ground conditions; react to a market where quickly changing orders occur regularly; and address as-drilled blast patterns as opposed to baseline plans. “Real-time” data exchange into and out of the blasting process supports the whole-of-mine data management that the industry is migrating to.

Jan 1, 2010

By Chris Vagasky

On July 10, 1926, lightning struck at Picatinny Arsenal, New Jersey, and caused the explosion of at least 600,000 pounds (272,000 kilograms) of ammunition, resulting in more than $600 million (2015 dollars) in damage, the destruction of 200 buildings, and 22 deaths. Fortunately, there has not been a major incident involving lightning and explosives in the US in some time, though lightning has destroyed fuel storage tanks in recent years, including in North Dakota, Texas, and Ohio. Lightning poses a significant hazard to the explosives industry. Carrying high currents and temperature, lightning can cause explosives to detonate, start fires near storage facilities, and injure or kill operators.

Jan 1, 2017

By Ruilin Yang

This paper provides a theoretical analysis of shockwaves in an air-deck induced by detonation of an explosive charge and shows that the initial shock pressure in the air-deck at the interface with the explosive charge is only about 1% of the detonation pressure. A rarefaction wave with the low pressure travels back into the explosion detonation products greatly reducing the post-CJ detonation pressure. Additionally, AUTODYN modelling shows that the pressure attenuates further during shockwave propagation along the air-deck. Although the pressure increases at the bottom of the blasthole due to shock reflection, the overall pressure in an air-deck does not increase and is still around 1% of the detonation pressure which is too low to break most rock.

Jan 1, 2016

By R. Jacob Cefalo, Miguel Valenzuela

The modern drill and blast engineer operates in an environment often rich with data from drilling data and blast designs vs. actuals to fragmentation distributions and vibration records. Despite this abundance, much of the information generated remains underutilized, often collected as a matter of routine rather than for a means to an end. This paper explores how artificial intelligence (AI) can bridge that gap, transforming raw operational information into actionable insights that lead to more consistent and optimized blasting outcomes. Through AI-driven analysis of drilling logs, burden and spacing measurements in design vs. actual, fragmentation distributions, and vibration records, we can identify hidden patterns and correlations that traditional analytics overlook or that we may not be aware of. These insights enable engineers to proactively adjust designs and loading strategies, ultimately improving performance aspects such as improving fragmentation, minimizing ground vibration, and lowering overall operational costs. The paper examines the industry's reliance on lagging indicators, such as post-blast fragmentation surveys or actual powder factors, and suggests the need to shift toward leading indicators like real-time drill data monitoring and predictive fragmentation modeling. Utilizing AI to forecast outcomes before a blast is carried out allows engineers to take corrective actions early in the process, thereby creating a feedback loop that continuously improves performance. This integration of AI into drilling and blasting practices marks a pivotal opportunity for the explosives engineering field to evolve from reactive to predictive methodologies unlocking a new level of operational intelligence and value creation.

Jan 26, 2026