Search Documents

By Perry Sisk

In order to protect nearby structures during a blasting project, a peak particle velocity limit is often stipulated by a government agency or the owner of a particular structure. At the start of a blasting project, a preliminary estimate for the minimum scaled distance is often determined using a vibration prediction equation before any site-specific data have been obtained. Reasonably conservative assumptions are typically made for the unknown input variables in the vibration prediction equation until site-specific blasting data have been obtained and evaluated. Although this approach is prudent, it provides no assurance that the peak particle velocity values generated during the initial phase of the project will be below the specified limit.

Jan 1, 2013

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Lon Santis, Michael Swisdak, David Leidel, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc (APT) have developed and released a quantitative risk management tool, IMESAFR (IME Safety Analysis For Risk), for the commercial explosives industry. Consequence algorithms in IMESAFR are considered state-of-the-art. Generally, they mirror those in SAFER (US Department of Defense Explosives Safety Board quantitative risk management software). The science behind the software has now been assessed for its maturity. Results have identified areas where additional test consequence data could improve predictions. To address these areas, full-scale testing programs to provide the needed data have been formulated. Proposed testing efforts include work to: (1) improve characterization of explosive articles now absent from SAFER, and (2) refine modeling of the Potential Explosion Site (PES) types, particularly small metal structures, also not found in SAFER. Goals of each program as well as requirements for conducting the tests have been established. Testing results are to be used to improve the algorithms and to further the state-of-the-art in risk-based explosives safety.

Jan 1, 2012

By S B. Richardson, D Mead, N T. Moxon

The use of air-decks to reduce explosive costs has become very topical in recent years. The majority of the research in this area has been arried out between the Soviet Union where reductions in explosive consumption of between 10-30% have been claimed with apparent benefits being gained in both fragmentation and movement. Work carried out by the University of Maryland using thick plexiglass blocks has supported these findings and indicated that air-decks in measetbe duration of action of the shock wave on the surrounding material by a factor of 2 to 5 (see Figure 1). Although the fracture network resulting from this mechanism is not as intense as that produced adjacent to the explosive charge it does appear to act over a larger volume of material. Although the mechanism attributed to air-decking has been studied in some detail the effect of this mechanism on the size distribution of material produced during a blast does not appear tot have attracted much attention.

Jan 1, 1991

By Catherine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his suppher specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation. The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1992

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By M. Gonçalves Peixoto da Silva, E. Rodrigo Carvalho Souza Siqueira

Mining in narrow veins is commonly applied for precious metals, generally carried out to extract gold in underground mines, due to the ore occurrence on narrow veins, mainly up to 2-meter large. The current work presents the implementation of the methodology in a zinc mine located in the state of Minas Gerais in Brazil. The Vazante Mine through the years has always carried out mining on stopes with a thickness larger than 3,5 meters, but nowadays due to the need to reduce the waste planned in its blocks, as well as increase the useful life of mine, mining has been implemented in blocks that are less than two meters. Given this, the challenge is to be able to carry out blasts that does not exceed the operational dilution required and does not generate an impact on recovery, as working with extremely heterogeneous stopes. This study seeks to correlate the main characteristics of stopes and its relationship with the results obtained in the execution of those blasts. Also, it proposes an analysis between the empirical data, and existing theoretical references, creating ideal mining parameters, such as minimum thickness, maximum height, and optimum timing in the blast plan. One of the main challenges for carrying out this mining method is the control of operational dilution, generally pointed out as the biggest difficulty for companies that adopt this methodology, due to the thickness of those stopes, any displacement can make it unfeasible, thus the technical level on carrying out the drilling and loading of these blocks must be impeccable, an understanding of the structural geology of the site is also essential for dilution control. The outcome will be a set of ideal parameters and mining methodology to guarantee the success in execution of these blocks, thus bringing a financial benefit to the company.

Jan 21, 2025

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor.

Feb 1, 2020

By John W. Brown

"Adequate dust control in and around rock drills is a problem that must be solvedfor the health and safety of workers running the drill as well as those working around thedrilling operation This paper will discuss the designs available from most drill manufacturers todayand the effort ‘nvolved in keeping them effective on a productive basis."

Jan 1, 1999

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor. If a blast is fired using 1.25" (32 mm) diameter product and a 10-foot (3 m) bench, vertical uplift of 60 feet (18.3 m) would be considered extreme and violent by any professional in the industry. However, a 100-foot-high (30.5 m) bench using 12" (305 mm) bulk product, having a vertical displacement of 60 feet(18.3 m)might be considered typical or non-worrisome. This is where violence factor is beneficial as itprovides a system of scaling the violence of a blast based on the bench height to give manager a keyperformance indicator (KPI) which is easy to monitor and can provide a large amount of information onsite-specific design variables for their performance on blasting and the end-results of the blast. The Violence Factor of a blast is an integer which is scaled to determine how high vertical uplift of a blast is compared to the bench height. This project analyzed numerous blasts to determine what blast design variables contribute to violence. This violence has also been shown to occur when a non-optimal breakage mechanism, cratering, occurs and the design criteria that lead to this cratering. Finally, this paper will present typical results of various levels of violence including backbreak, fragmentation, and muckpile configuration.

By Doss Brittain

The term ground breaking is taken to include the process of so loosening the ground as to enable it to be readily loaded into buckets or cars and hoisted from the shaft or drift. In the Joplin district are encountered two varieties of ground, the hard and the soft. Hard ground consists of massively bedded rock requiring heavy blasting to loosen it. Such ground is to be found throughout the district in the same localities as the soft ground but more extensively, even to the exclusion of the appearance of soft ground in the sheet formation in the vicinity of Webb City. The Yellow Dog Mine at Webb City and the Grace mine on the Granby land at Joplin furnish well known examples of hardground mining which has become the most extensive in the district.

Jan 1, 2008

By César Ugaz Castañeda, Paulo Fernández Alvarado, Richard Sotomayor Oblitas, Rocke Enríquez

Mina El toro has been making substantial changes in its operation to improve its social impact and productivity. Because of the use of gasified emulsions and electronic initiation system, it was possible to mitigate vibrations and carry out massive blasting, increasing its production by 4.2% and minimizing complaints from communities.

Feb 1, 2020

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By Robert Hopler

HUDSON MAXIM A Noted Inventor of High Explosives ALTHOUGH the subject of the present sketch has been a tireless worker in many fields of activity, his name is best known in connection with his work in the development of high explosives and their application to modern ordnance

Jan 1, 2012

By Roberto Folchi, Hans Wallin, Mara Battocchio

An understanding of explosives science and technology, and the competence to harness it is central to maintaining Explosives capability, national security, and in sustaining a competitive industry. A consequence of eroding this competence is the increased likelihood of explosives accidents. These are often catastrophic as demonstrated by accidents in Nigeria, Russia, Toulouse and Enschede. In addition to the serious loss of life there was the very significant damage to houses, domestic and industrial infrastructure and to the environment at a cost of many millions of Euros.

Jan 1, 2013