Search Documents

By M Sampara, W Comeau

The introduction of large-diameter holes to underground mining has made possible the development of new mining methods such as the Vertical Crater Retreat (V.C.R.) method. It is not only the safest underground excavation system but also provides mass production at a lower cost than any conventional mining method (1, 2, 3, 4, 5).

Jan 1, 1981

By Tacio Ferreira

A surface copper mine in the Western United States faced challenges in recovering rock and ore from final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall conditions. The operation had been using the same drill and blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at approximately 380,000 tons a year generated from an average of 60 final wall blasts performed annually. The mine engineering team and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. In this paper we present how we collected data, reviewed design standards, and found opportunities to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71% on the mine’s highwalls.

Jan 21, 2025

By Jim Daley

This case history discusses a pre-split test conducted at BHP Mineralss Navajo Mine in Fruitland, New Mexico. The test was an extension of earlier pre-split testing conducted by Virgil Stachura of the U.S. Bureau of Mines in conjunction with Navajo Mine and WESCO Inc. which tested low-density product in 10.625 diameter holes.

Jan 1, 1996

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Henry P. Van Ormer

This paper is written to outline the capabilities and flexibility of the electric motor driven oil cooled rotary screw air compressor in construction and mining applications. With the changing economics between fuel and electric power all over the world, the viability of the electric motor is a choice all construction and mining people should be aware of. The advent of large efficient electric motor driven rotary screw compressors have given a great deal of flexibility to the use of these units on many applications not considered before. Examples are given for rotary and percussion drilling, fennels, and underground, sandblasting and "uniting, general uses - shows wheel mounted and skid mounted units.

Jan 1, 1976

By Sean Cahill

The Blasting In the summer of 1999, a Southern California drilling and blasting company conducted blasting as part of the grading operations at the Highlands Ranch development in San Diego, California. Highlands Ranch was a new single family residential project located near older residential properties in the area. Blasting was necessary to remove indigenous meta-volcanic rock associated with the local geology.

Jan 1, 2003

By Diane F. Baker, Cathy Aimone-Martin

A series of small-scale explosive experiments were conducted in a perlite mine near Socorro, New Mexico. These experiments were a joint effort between Los Alamos National Laboratory, New Mexico Institute Of Mining and Technology, Southern Methodist University, and Defense Nuclear Agency. The purpose of these tests was to measure the changes in the shock wave and seismic coupling as a function of depth of burial and structural setting. The size of the explosive charges ranged from 1 to 68 kg. Over 1150 measurements of velocity and acceleration were made on thirteen experiments using three component sensors. The sensors were placed to maximize the azimuthal coverage as well as to provide data at a variety of ranges from ~1 to 130 m A few far field measurements were made at ranges of ~2Êkm. While the bulk of the measurements were made on the surface, high g accelerometers were placed in one instrumentation borehole to provide some free-field measurements. Preliminary results indicate that significant differences in the amplitudes of signals can occur when the location of the explosive charges are changed by only meters. Part of the observed difference is attributed to variations in the rock immediately adjacent to the charge affecting the shock coupling; and part to the effects of the site characteristics.

Jan 1, 1994

By Ken Roosa

Blue Circle Atlantic of Ravena, New York, operates a four million ton per year quarry. The quarry management objective is to maximize crusher throughput tonnage while optimizing the aggregate cost to drill, blast, dig, haul, and crush a ton of rock. To meet this objective, Blue Circle,s blasting program combines, large diameter production blastholes with medium diameter satellite blastholes.

Jan 1, 1989

The underwater explosions have been used for several decades for the determination of energy content of explosives. This test method is the only one by which shock, fly rock and total energy can be measured separately. It enables to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the fly rock energy is very important feature for the blasting explosives. The purpose of this study was to establish a test place for the underwater experiments in an old water filled open pit, to estimate the repeatability of the energy measurements, to calculate the standard deviations and to compare the total energy content of commercial explosives to the theoretical values calculated by the thermo dynamical program. The test method seems to work quite well especially for the homogeneous explosives. The difference between the energy content of theoretically calculated and measured values for the homogeneous emulsion explosives was about -3% and for the dynamite about -5%. The energy difference for the unhomogeneous ANFO was detected to be -19%. The diameter of the charge was 15 cm and it was obviously too small for ANFO to detonate ideally. On the basis of the test results this test method seems to fit best for the cap sensitive, completely homogeneous, spherical charges whose masses are big enough and which are initiated from the centre of the charge. The underwater explosions as a test method is the only one which can separate shock, bubble and total energies from each other and therefore makes it possible to develop the properties of explosives for different purposes which is very important feature of this method.

Jan 1, 2005

By William H. Snyer, Hank Cox

A high explosive device using Linear Shaped Charge (LSC) (to rapidly cut vent and drain openings in a rail tank car) is described. In the event of damage to a tank car loaded with a pressurized flammable fluid, it may sometimes be necessary to perform controlled on-site vent, drain and burn operations. Existing techniques required refinement to achieve the desired safety and procedural reliability for use in emergency situations.

Jan 1, 1994

By S Lukovic, Robert Briton, Calvin J. Konya

Investigators have reported that charges which are decoupled from the borehole wall produce different fragmentation then those which are fully coupled. The difference in effect could be as a result of energy doss during transmission across the air gap or it could be due to the change in detonation characteristics of the explosive as a result of the change in confinement on the charge during detonation. In order to better understand the phenomena of decoupling, a research project was conducted at the United States Bureau of Mines Station, near Pittsburgh, Pennsylvania. It was decided to use shock and bubble energy tests along with simultaneous velocity measurement to determine the mechanics of decoupling and energy transmission. Two explosives were selected for the test, one dynamite and one water gel. Test results indicated that decoupling could both boost the total energy output of the explosive and that further decoupling would drop the energy output.

Jan 1, 1987

By Gregory P. Lorsbach

Significant information about any blast is contained within the seismic signal generated by the blast. In this study, standard digital signal processing techniques are utilized to extract source parameter information from a seismic signal recorded at distances commonly used in compliance monitoring. Specifically, digital seismic data was analyzed using the cross-correladon and autocorrelation functions for the purpose of determining delay timing. The initial results are interpreted to indicate that: 1) Individual delays can be identified analytically but not visually for short delay periods and large source to receiver distances, 2) Delay timing can be resolved to a few milliseconds, and 3) Results can be obtained from data collected at a minimal number of locations.

Jan 1, 1991

By Hubert den Dikken

ache, especially when it comes to forwarding of small quantities. Air transport is limited to 1.4 explosives on cargo aircraft and 1.4S classified explosives on passenger aircraft, so most samples cannot be transported by air. Ocean transport is a possibility, but due to stowage and segregation regulations of the IMDG code, a very expensive one. Road transport is often the only solution, but high explosives require special trucks with licensed drivers. The solution to these logistic problems is solved by creating a 1.4S (Class C) classification for all high explosives, when packed in special containment vessels.

Jan 1, 1995

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Charles H. Dowding, Catherine T. Aimone

Rock particle sizes were measured at fourteen steep-slope Appalachian coal mines during production blasting. The distribution of rock sizes shows the effects of inter-hole timing, sequence of hole initiation, as well as charge distribution within each shot. Blast design parameters were selected to: (1) minimize displacement of broken rock conforming to throw control required of mining methods, (2) minimize seismic effects, and (3) create breakage at a cost economical to mining operations.

Jan 1, 1983

By Pierre Mousset-Jones, Geraint W. Harris, Robert Karlin, Jaak Daemen

In order to minimize the ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will make it possible to more accurately locate the grade boundaries on the surface of a blasted rockpile prior to excavation. This paper describes the development and testing of a method to accurately measure the direction and magnitude of sub-surface blast movement. The technique involves the use of magnetic "radiometry, using a cesium vapor "radiometer and real-time differentially corrected, GPS system, to locate the post-blast position of magnetically enhanced target objects, whose pre-blast locations are known, without disturbance of the blasted rock. The objective is to design an accurate and efficient technique which can be integrated into a mines production cycle.

Jan 1, 1997

By Walt Meglasson

"Developing technologies in demolition equipment and processes have produced a newsophistication within the demolition industry. Yet, with increasing frequency, owners,architects, engineers, and contractors reject out of hand one of the safest and most effectivetools in the demolition industry today, specifically the use of explosives and blastingtechniques in man_made structure removal. The use of explosives in any application mustbe considered as a tool, no more or less dangerous than any other type of tool, when usedproperly. Accordingly, importance must be attached to recognizing the skill, integrity, andcare of those who use it. Massive amounts of information and help are available to assistthe rock blaster, ranging from the practical to the highly theoretical, but very littleinformation exists to guide anyone considering unleashing the power of explosives instructural demolition blasting. The planning and work required to execute such projects iscomplex, and the recognition of the different applications explosives can be applied to isthe first step."

Jan 1, 1993

By S S. Kahlon

India is a large and growth market for explosives and accessories, which has dramatically changed from complete import dependence to self sufficiency, and now has an exportable surplus. The largest single user is coal mining which is continuing to show a healthy growth with opencast mining becoming increasingly dominant. The explosives industry has kept pace with mining and today all the well renowned explosives technologies of the world are available in the country. While slurry explosives are popular in large diameter, NG based explosives continue to be preferrred in small diameter usage. Emulsion explosives have had a good market response. ANFO usage is limited due to local reasons. As the mine size is increasing, the demand for bulk-on-site explosives is growing. Prices of explosives and accessories are cheap compared to international levels. The user industry is mainly Government owned mines whose profitability is not satisfactory. Explosives industry is over licensed in terms of manufacturing capacity, which is likely to put pressure on the viability of some of the explosives manufacturing units. Scope exists for optimization of blasting parameters through the use of computerized blasting models. The explosives industry is faced with new challenges and opportunities.

Jan 1, 1987

By Joseph L. Uraco, Harry C. Verakis

The use of explosives in underground coal mines presents a potential risk for serious injuries and death to miners. Widespread disasters have occurred from the explosion of methane and/or coal dust initiated by blasting with explosives. Many of these disasters took place in the early 1900's when the use of black powder for blasting was prevalent. Historically, the investigations in the U.S.A. to develop and test safer explosives for blasting coal began in 1908 when a testing station was established in Pittsburgh, Pennsylvania. Since that time, great strides have been taken in the development of safer explosives. The use of safer explosives has significantly reduced blasting accidents in coal mines. Enactment of legislation, such as the Federal Coal Mine Health and Safety Act of 1969 and enforcement of regulations has also improved blasting safety. More recently, MSHA began a major revision of its regulations for blasting in coal mines. In 1988, MSHA published final rules for the approval and use of permissible explosives in coal mines. The approval requirements for explosives address testing and evaluation. The requirements include tests for sheathed explosives which represent a new technology. The use regulations provide increased safety protection for miners by including standards to address identified hazards. Major aspects of these standards, such as qualifications for blasters, multiple-shot blasting and the use of sheathed explosives are discussed.

Jan 1, 1992

By Cam B. Grundstrom

This paper will describe blast design modifications that have been made at the Island Copper Mine, near Port Hardy, British Columbia. To date, two additional designs have been implemented in an effort to reduce final wall damage and increase productivity. The typical blast patterns in use at Island Copper were monitored in an effort to build up data to which new designs could be compared.

Jan 1, 1994