Search Documents

By Hossein Zarei, Masoud Kashani, Mehdi Safari

The feed of flotation unit in Angouran mine, as a part of Iranian Lead and Zinc National Corporation, contains about 34.26% zinc (about 12% Zn sulphide) and 10.14% lead (about 2% Pb sulphide). The grade of Pb and Zn in the final concentrate (rougher+scavenger), under optimal conditions (200 g/ton PEX, 500 g/ton zinc sulfate, 30 g/ton MIBC and pH = 7.5), was 63.18% and 13.01%, respectively, and the total Pb (sulphide-oxide) recovery was about 19% which included 95% Pb sulphide. The grade of Pb and Zn in rougher concentrate step was about 71.86% and 5.97%, respectively, when PEX (Potassium Ethyl Xanthate) was used as collector. While in the presence of PAX (Potassium Amyl Xanthate), the grade of Pb and Zn in rougher concentrate step was 66.8% and 10%, respectively. Tailing of the galena flotation (with 8.48% Pb grade and 34.92% Zn grade under the optimal conditions) was used as a feed for sphalerite and oxide section flotation.

Jan 1, 2014

By T. Saastamoinen, N. Heino

"The Olserum deposit located in Sweden hosts an indicated mineral resource of 4.5 million tonnes over 0.6 % TREO, exhibiting a relatively high proportion of HREE. Beneficiation of a composite drill core sample was studied in the flowsheet of magnetic separation of magnetite followed by REE minerals flotation. Primary testwork was performed to select an effective REE mineral collector and then the parameters of grinding size, collector and depressant dosages, slurry pH and density, conditioning time and temperature, and flotation time were tested for optimization of REE flotation. The studies of process mineralogy showed that the REE-bearing minerals monazite, xenotime and apatite were successfully enriched from the concentrations of 0.6%, 0.31% and 2.6% in the feed to those of 17.0%, 8.9% and 65.0% in the concentrate with the recoveries of 79.0%, 81.3% and 71.0%, respectively. INTRODUCTION The Olserum deposit located in Sweden comprises lower grade placer material with higher grade apatite-magnetite veins and hosts an indicated mineral resource of 4.5 million tonnes at 0.6% TREO, with 34% of that being HREO (EURARE, 2017). The mineralization was studied by Andersson et al. (2018). At early stage, high-temperature REE is characterized by abundant monazite-(Ce) and xenotime-(Y) coexisting with fluorapatite and subordinate amounts of (Y,REE,U,Fe)-(Nb,Ta) oxides. During a subsequent stage, allanite-(Ce) and ferriallanite-(Ce) formed locally, partly resulting from the breakdown of primary monazite-(Ce). Alteration of allanite-(Ce) or ferriallanite-(Ce) to bastnäsite-(Ce) and minor synchysite-(Ce) at lower temperatures represents the latest stage of REE mineral formation. The mineralogy and beneficiation were firstly studied by GTK Mintec in the EURARE project for a composite drill core sample. The Olserum is considerably smaller than the Norra Kärr deposit. However, REE are hosted by xenotime and monazite, both of which have well established processing pathways, and meanwhile, the Olserum has a high contribution of the high value critical REE (dysprosium (Dy), yttrium (Y), neodymium (Nd) and terbium (Tb)), which provide a unique advantage for its exploration (Tasman Metals Ltd., 2013). In this paper, flotation of the REE minerals in the Olserum ore was studied."

Jan 1, 2018

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"In conventional flotation, fluoride ions selectively would react with the aluminum site on the microcline surface and produce negative charged sites for amine to be adsorbed (Smith, 1976). According to this view, aluminum site is considered as a key feature in feldspar flotation. Generally, fluoride ion has been widely used as a modifying agent in silicate flotation. Since O'Meara's patent appeared on HF -amine reagent system to selectively float feldspar from quartz in 1942, relatively few contributions have been devoted in this issue. The reason might be that the process works very well, and accordingly there is no initiative to investigate in this area. However, due to the awareness of international community to restrict using of hazardous reagents like HF, sound engineering practice to search for alternative methods, not utilizing HF, has been launched. Inspection of literature, one can find several works dealing with this issue.In this contribution, the effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases."

Jan 1, 2003

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"For about 20 years, the use of bacteria to control the flotation process for the production of raw material concentrates has been the subject of worldwide scientific and engineering efforts. The objective is to reduce the consumption of biologically non-degradable toxic reagents. The principle idea is to use the activity of bacteria in natural leaching processes – known since the middle of the last century – for controlling flotation processes.It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS), excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 21 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction. Pure mineral phases and mineral mixtures were used for the flotation tests. The outcome was reproducible results with technical flotation machines. The research results known so far are mainly based on investigations with micro flotation devices, which are usually used for the characterization of reagents and which do not allow a direct translation to the technical scale."

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips, David G. Barker

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented.These results show that single sensor analysis information from the surface vibration system can be used as soft sensor inputs for monitoring process variables such as mill load that until now, have not been reliably measured. System outputs also show considerable promise in the area of condition monitoring. An example of the signal analysis output is presented showing elevated vibration levels in an area with higher resultant wear. Eventually, it is considered that outputs from this system for process variable and wear condition monitoring will be key new inputs to an online AG/SAG mill monitoring and control system."

Jan 1, 2003

By Sydney Mantsho, Toni Streczynski, Manuel Gonzalez

"In 2013, the commissioning of the MillStar Stabilisation and FloatStar Stabilisation and Optimisation controllers were completed at the Cerro Bayo Silver (Ag) mine in Patagonia, Chile. The MillStar control system has stabilised the feed to the SAG mill as well as the density at the discharge end of the SAG mill and ball mill. The FloatStar Stabilisation and Optimisation controllers have successfully stabilised and optimised the flotation circuit to ensure consistent product quality within desired specifications.The mill feed is controlled utilising the MillStar Solids Feed controller. Additionally, the solids to liquid ratio into the SAG mill was controlled utilising the Mill Inlet Ratio controller in conjunction with the Solids Feed controller. The discharge end of the milling process is a highly interactive and complex system. The use of a Robust Nonlinear Model Predicative Controller (RNMPC) was ideally suited to control this section of the process. On the Cerro Bayo milling circuit, the RNMPC was used to control the mill discharge sump level and the primary cyclone feed density to produce a more consistent feed to the flotation circuit.Three levels of the FloatStar control system were installed, for flotation stability, concentrate flow stability as well as grade optimisation. The Level Stabiliser was used to stabilise the level control on 6 flotation banks. The Flow Optimiser was commissioned on the Rougher, Scavenger and Cleaner concentrate sumps to stabilise concentrate flow from the flotation cells. The Grade Recovery Optimiser was commissioned on the Roughers section. A number of instrumentation challenges were identified which limited the overall benefit derived from the system. Once these were addressed, the performance was optimised. The overall benefit provided by the system was observed in terms of the improvements in Ag recovery."

Jan 1, 2014

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By U. A. Peuker, T. Mütze, F. Shayo, A. Wikedzi

"Buzwagi Gold Mine (BGM) is operated by Acacia Mining and located in the Lake Victoria Goldfields of central Tanzania. The mine treats a sulphide copper-gold ore to produce gold in form of doré bars and a concentrate containing gold, copper and silver. The BGM comminution circuit includes a primary crushing stage with a gyratory crusher and two grinding circuits using a Semi-Autogenous Grinding (SAG) mill and a ball mill. Currently, the grinding circuits are inefficient in achieving the aspired product fineness of xP,80 = 125 µm even at low to normal throughputs (450-600 t/h). An optimization study of the circuit performance was conducted to improve product fineness through circuit surveys, experimental lab work and simulations. The analysis of survey data revealed inefficient grinding operation characterized by ball mill product (xP,80 > 400 µm) coarser than designed and higher hydrocyclone cut sizes (xT > 200 µm), too. In MODSIM several options were simulated such as reduction of vortex finder and apex diameters, reduction of SAG screen aperture, and modification of cyclone feed density. An improvement of product fineness could be achieved by simulation of the cumulative changes but it was also concluded that the current equipment cannot achieve the target. Further simulations showed that a second ball mill might help to achieve the desired fineness as well as an increase of grinding throughput by up to 26 %. INTRODUCTION Simulation of comminution, particularly grinding and classification, has received great attention for many years, due to the fact that the unit operation is by far the most important both in terms of energy consumption as well as overall plant performance (King, 2001; Wills et al., 2006). The use of simulation is advantageous due to low cost as well as its ability to consider many variables simultaneously. Moreover, there are some benefits for optimizing grinding operations by simulation like decreased unit operating costs, increased capacity, and improved performance of downstream processes due to improved feed size distribution. This paper presents an optimization study for the grinding efficiency at Buzwagi Gold Mine. This was achieved through three full scale circuit surveys, lab work and simulations with MODSIM."

Jan 1, 2018

By L. X. Yu

As is known, the oxidized antimony and antimonate are hard to treat. A new combined mineral processing flowsheet which is controlled in grinding and classification ?bulk floatation?gravity separation is adopted to dispose of gravity-separated tailings (antimony content: 1.48%; oxidization rate: 68.92%) in Muli Antimony Mine, the grade of floatation antimony concentrates is 32.64%; the grade of gravity-separated antimony concentrates is 26.99%; the combined grade of floatation and gravity-separated antimony concentrates is 30.85%, and the total recovery of antimony is 70.64%. Adopting the new mineral processing technique have solved the problem of over grinding of antimony ore by controlling grinding and classification, recovering effectively the sulfide antimony and the easy floatable oxidized antimony of fine size by bulk floatation, recovering effectively the oxidized antimony which is hard to float by classified gravity separation. This is a great breakthrough in the mineral processing technique of the recovery of the oxidized antimony. At present, favorable economic benefit has been obtained from the application of this processing technique in Muli Antimony Mine.

Jan 1, 2014

By S. Banisi, A. R. Hasankhoei, A. R. Ghasemi, E. Razi, G. A. Parsapour

At the pelletizing plant of the Gol-E-Gohar mining and industrial company two parallel dry closed grinding circuits, each with the average throughput of 300 t/h, are used. Each grinding circuit consists of a burner, a dry ball mill (6.2 m×13 m) and an air separator. The ball mill consists of a 2 m-long drying and an 11 m-long grinding chambers. The iron ore concentrate is fed to the drying chamber by a feed chute. The first 1.35 m of the drying chamber consists of 56 flights in two rows to decrease the feed moisture from 5% to below 0.2% and the rest of dryer chamber consists of deflectors to pass the material to the grinding chamber. It was found that when the feed moisture content increased from 1.3% to 3.5%, the throughput decreased by 12% (35 t/h) indicating a low performance of the dryer. Monitoring the wear rate of flights for a period of 12 months showed that the first 0.8 m length of the flights length did not experience any wear. This means that about 59% of flights do not contribute in material distribution and drying. A DEM simulation of feed chute and the drying chamber demonstrated that due to the inappropriate design of feed chute most of materials do not get in touch with the first 0.8 m length of the drying chamber. To overcome this problem, various feed chute designs with different geometries were simulated by the KMPCDEM© software. With the aim of arriving at a proper material trajectory, where the total length of the flights are used, a new feed chute was selected. The simulation results indicated that if the height of the flights is increased from 1.60 to 2.26 m and the slope is increased from 45 to 48 degrees the material arrive at the first 0.48 m of drying chamber. In this manner, the unused part of the drying chamber decreases from 59% to 36% of the length. After installation of the new feed chute, during a period of three months the throughput increased by 36 t/h.

Jan 1, 2018

By K. Yoo

Cuprous oxide is one of the oldest antifouling agents and also acts as red pigment in these paints. In printed circuit board manufacturing industries, waste etchant contains a substantial amount of copper ion. In the present study, a process was suggested for recovering cuprous oxides from the waste etchant and optimum conditions were investigated to recover the cuprous oxides. The process consists of two steps: in first step, Cu powder is added into wastewater solution, and cupric ions re-duce into cuprous ions (Cu+Cu2+?2Cu+), where cuprous ions precipitate as cuprous chloride; In second step, cuprous oxide is synthesized by adding NaOH into cuprous chloride solution (2CuCl+2NaOH?Cu2O+NaCl+H2O). Optimum conditions were investigated to recover cuprous oxide in the processes. When copper powder was added into wastewater with copper ions, Cu concentration decreased from 15.6% to 2.6% and ORP decreased from 620 mV to -59.9 mV. This result shows that cupric ions reduced into cuprous ions. XRD data indicated that the precipitate was cuprous chloride powder. Using the cuprous chloride recovered and NaOH solution, cuprous oxide was synthesized. To investigate the optimum condition, various NaOH solutions were added into water with CuCl, and then pH, ORP, Cu concentration, Cu contents in precipitates were analysed. XRD data showed that main component of precipitates was cuprous oxide.

Jan 1, 2014

By Xiaoxu Sun, Jianchao Yao, Jiancheng He, Shijie Lu, Hongxi Zhou

"With the trend of increasingly more mineral resources turning low-grade and refractory, more and more new ore bodies being developed worldwide are more finely grained, which drives the rapidly development and application of techniques related to tower mills (vertical spiral stirred mills). However, the lacking in fundamentals of fine grinding, as well as standard procedures for equipment selection and scale up, seriously restraint high efficient application of tower mills. Taking grinding media motion characteristic and grinding intensity as a breakthrough point, this paper studies mechanisms behind how critical parameters affect grinding efficiency of tower mill, including ratio of screw pitch and diameter, agitator rotation speed, grinding media size. Several sets of orthogonal test are conducted on the quartz ore using the grinding system of KLM-3 tower mill. All the tests are under the same character of feeding mineral and undergo the consistent sampling for at least 60min grinding time. The input power is measured by a torque measurement system and the grinding products are analyzed by the laser particle size analyzer. The test results show the influence of parameters on grinding efficiency. Among the three important parameters, the effect of grinding media diameter is the biggest, followed by the agitator tip speed, and finally the ratio of screw pitch and diameter. For the different particle size of grinding products, the best combination of grinding parameters is different, with the mineral size becoming finer, the ratio of screw pitch and diameter become smaller, the diameter of grinding media become smaller, while the agitator tip speed does not change too much. The conclusions of the study help us to improve the grinding efficiency of the tower mill, to assist in the selection and optimization of working parameters, establish new scale up method on the basis of grinding model and eventually provide theoretical basis of rational selections of structural and media physical parameters within tower mill."

Jan 1, 2018

By David Morrow

Fly ash is a by-product from coal-fired power stations that is captured from the exhaust gas stream by electrostatic precipitators (ESPs) or bag houses. It is mainly derived from the inorganic components in coal but also contains residual carbon from unburnt fuel (measured as LOI). In the past, nearly all fly ash was sent to landfills or tailings ponds by power generators but this trend is quickly changing due to landfill costs, sustainability requirements and the inherent value in correctly processed fly ash. The main property that makes fly ash suitable for recycling is its use as a pozzolan. Pozzolans exhibit cementitious properties that make them suitable for partial cement replacement, and that can have beneficial properties for concrete mix designs. Fly ash can be used to replace up to a third of the of the Ordinary Portland Cement (OPC) requirement. Suitable fly ash nearly always requires the removal of the less reactive coarser fraction from the finer fraction. Due to the pozzolanic nature of fly ash, it must be processed dry and separation is normally required at 45 micron. In response to the increasing demand from a range of dry classification applications, Metso purchased an established air classification technology suitable for both mining and construction applications. The classifiers intelligent design efficiently utilizes the air flow which keeps power requirements low whilst including a scrubbing/recirculating function within the classifier that allows extremely efficient separations even at very fine sizes. This technology is of global interest to Fly Ash processors, but should be of particular interest in India which is both the second largest cement producer in the world as well as producing 80% of its power from thermal sources. This paper is intended to give a brief overview of fly ash and requirements for use as a pozzolan, air classification of fly ash and a case study from an established and experienced fly ash producer. Keywords: air classifier, fly ash, pozzolan, fineness, cement, cholla, salt river materials group

Sep 1, 2012

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By G. Deschênes

In the last 4 years, the high price of silver attracted more interest for improving its extraction. Metallic silver and silver minerals require a high concentration of cyanide and show slow leaching rates and poor extraction. This investigation determined the effects of dissolved oxygen, lead nitrate and a pretreatment on silver leaching from slurry containing quartz mixed with metallic silver and high purity acanthite. Stephanite, pyrargyrite and polybasite were also used in the study. The silver minerals were characterized by chemical assay, X-ray diffraction analysis (XRD), image analysis (MP-SEM-IPS) and electron microprobe analysis (EMPA). Increased dissolved oxygen of the slurry produced the fastest silver leaching kinetics. The leaching of silver from high purity acanthite was determined under various conditions and compared to a new process called ?CANMET Enhanced Leaching Process (CELP). For a slurry containing acanthite, a 23% improvement (from 76% to 99%) in silver extraction was obtained with the CELP. In presence of pyrargyrite and polybasite, silver extraction increased from 75% to 90% and 86% to 99% respectively using the CELP. No improvement was obtained for the slurry with stephanite (99% extraction in 72 hours). However, the sliver leaching rate was much faster with the CELP. XPS analysis of individual silver mineral particles showed that CELP leached surfaces were considerably more oxidized relative to the conventional cyanidation leached surfaces. Leaching of two gold/silver ores indicated that the efficiency of the CELP increased with the refractoriness of the sample. Gold extractions were comparable for the two technologies while silver extraction improved up to 5% (70g/t) for the CELP. The final leach solutions contained lower concentrations of copper, which consequently reduces the effluent treatment costs.

Jan 1, 2014

By J. Y. Liu

The comminution in a high-pressure roller mill is modeled by an energy-based population balance approach considering three aspects of breakage taking place in the active zones of the mill: the interparticle breakage in the high-compression zone, the breakage at the edges of the rolls, and the pre-breakage in the acceleration zone. Together with an appropriate model of classification, this model can be used to simulate steady-state performance of closed-circuit grindings with high-pressure roller mill. After a brief description of the basic modeling approach, the algorithm of the steady-state calculation for a generalized grinding-classification circuit is presented, from which the circuit configurations commonly met in industrial practice can be derived. With an iron ore as feed material for example, simulation results are shown and discussed in respect of circulating load, specific energy consumption and product fineness for closed-circuit grindings under various operating conditions. The effects of stressing intensity, working gap, classifier parameters as well as circuit configuration on the overall circuit performance are investigated systematically by means of computer simulation.

Jan 1, 2014

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Jing Zhou

2-hydroxy-3-naphthoy hydroxamic acid code name F203 is a good collector of cassiterite, 1-hydroxy-2-naphthoy hydroxamic acid code name ZJ-3. F203 and ZJ-3 are similar series of isomers. They have similar naphthye, and similar series of functional OH and ?CONHOH, but the seat of OH and ?CONHOH group are different, on the F203 is 2.3; on the ZJ-3 is 1.2, ortho position too. According to Isomeric principle ZJ-3 is a good collector of cassiterite slime too. Using ZJ-3 as collector flotation -10µm occupies 90%, grade 1.16% Sn cassiterite slime of Da Chang Chehe concentration plant, pass one coursing flotation, two cleaning and one scarenging flotation, and obtains grand 18.26% Sn, recovery 92.68% cassiterite concentrate. The result proves the Isomeric principle of flotation reagents is correct again. This principle may supply to synthetize new flotation reagents reference. Keywords: F2O3, ZJ-3, cassiterite flotation, Isomeric principle, Isomeric principle of flotation reagents

Sep 1, 2012

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012