Search Documents

By Paola Campana, Maurizio Lenzi

"In the paper a non linear model for the analysis of the pile response to the axial loads is presented. The study aims to find a general analytical solution concerning the pile-soil interaction modeled by means of the method of the load transfer curves. It makes use of a criterion based on the plastic and on the hardening work locally done by the shear stresses and due to the current elastic shortening of the shaft. Then a specific solution, denoted fractal model, is found applying recurrent relations that link the shaft shear stresses and the tip normal stresses to the pile settlements. These relations are based on that one proposed by Kondner in modeling the soil samples response in the triaxial tests and then used by Chin in the inverse slope method in estimating the pile capacity by the load test results. The comparison between the model predictions and the load tests measures validate the fractal model.INTRODUCTIONThe behavior of the axially loaded piles is known to be characterized by a highly non linear trend caused by the onset of plastic and irreversible deformations in the soil starting just from the first load levels. With the purpose to reach a deeper understanding of the pile-soil interaction, the influence of the soil inelastic properties on the distribution of the axial loads and of the vertical displacements is investigated. The research starts analyzing the behavior of an infinitesimal length of a pile embedded in a non linear homogeneous soil. That initial study leads to a criterion based on the plastic and on the hardening work locally done by the shear stresses and that allows to find the axial loads as a function of the elastic shortenings of the shaft. The relation that links the pile axial load to the elastic strain of the pile material is then used. That allows to find the vertical displacements and the axial loads as function of the depth in a parametric form in which the tip settlement acts as an independent parameter. The method of the load transfer curves is used and the effects of the pile technology are included in the soil constitutive relations. The analysis is then extended to the non-homogenous soils in a very effective way. The solution is applied taking as constitutive relations of the pile-soil interface the one proposed by Kondner to analyze the soil triaxial tests and by Chin to interpolate the pile response measured in the load tests."

Jan 1, 2017

By Michael Perlow Jr

A modification of the original Davisson Offset Limit (DOL) is presented for drilled foundations using soil quake (QDOL) factors ranging from 2 to 6. A further modification of the Davisson Offset Limit has also been developed using helical pile soil quake values (HDOL) based upon helix diameter. In addition, the initial tangent slope (IS) of the pile load test displacement curve is used in lieu of the calculated elastic slope (ES) to eliminate many of the uncertainties associated with determining the drilled foundation pile elastic modulus. The QDOL and HDOL load test methods do not require any graphical interpolation and provide easy simple ultimate pile capacity interpretation methods where drilled foundation pile load tests are not carried to plunging failure. Drilled foundation and helical pile load test case studies are presented to demonstrate the use of the modified soil quake QDOL and HDOL Methods.

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021

This Section describes four alternative methods for load testing of drilled shafts: high strain dynamic test (HSDT), rapid load test, static load test, and bottom load test. Until recently, static load tests were the only method available for verifying the capacity of a drilled shaft. However, because many drilled shafts carry very high design loads, the static load test was prohibitively expensive. The alternative methods, HSDT, rapid load testing, and bottom load testing are gaining acceptance because of their lower cost and faster implementation. However, these different methods do not necessarily yield the same results. This section describes the load testing methods and the differences that may occur when interpreting the test results.

Jan 1, 2004

By Timothy Nelson, Simon Burnworth

"The University of California’s new Berkeley Art Museum and Pacific Film Archive will showcase a collection of art and film in a facility that pairs an existing 1930s-era printing press facility with a new, architecturally unique auditorium wing. The centerpiece of this adaptive-reuse project is the existing 3- story art-deco Administrative Building, which will be integrated into the new museum and provide approximately 18,000 square feet of usable space. Degenkolb Engineers, as the shoring engineer of record, along with Condon Johnson & Associates Inc., the shoring contractor, worked together with general contractor Plant Construction Company to design and build a temporary structure to facilitate the complex retrofit, renovation, and expansion of the Admin Building. This paper will discuss the challenges faced by the design and construction team, the sustainable solutions implemented on the project, and the collaboration between teams to meet the unique constraints of the project and the site.INTRODUCTION AND PROJECT BACKGROUNDThe Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California Berkeley (UCB) campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home."

Jan 1, 2017

By Bernard H. Hertlein

"When the Deep Foundations Institute (DFI) was founded, quality assurance and quality control (QA/QC) of foundation construction was rudimentary. Nondestructive testing (NDT) was a nascent technology, known to very few people, and very limited in its capabilities and applications. In the four decades since the DFI became a reality, NDT researchers and practitioners have taken advantage of technological advances to improve those existing testing and analysis techniques, and to create new ones that have all contributed to the engineering body of knowledge. This has enabled contractors to improve the quality and reliability of their products, and engineers to design more efficient foundations.Through its regular series of seminars, publications and annual meetings, the DFI has been vitally important in educating the deep foundations industry about the capabilities and benefits of NDT methods. In turn, NDT results have helped the industry identify problems in deep foundation construction, determine the causes of those problems, and improve design constructability and construction practices to increase the quality, reliability and efficiency of all types of deep foundations. This presentation reviews the evolution of several important NDT methods, and the contributions that they have made to foundation quality.THE BEGINNINGSThe Deep Foundations Institute (DFI) was incorporated in 1976 in the State of New Jersey as a 501(c)(6) non-profit association. The DFI is a consensus organization of Contractors, Engineers, Owners and Suppliers involved with the design and construction of all types of deep foundations. The purpose of the DFI was and still is to improve the planning, design and construction of deep foundations by educating all those involved, sharing best practices, and promoting the adoption of new technologies that improve quality, productivity or safety.This is well expressed in the current DFI Mission Statement: To bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and a consensus voice for continual advancement in the deep foundations industry.At the time the DFI was born, nondestructive testing for verifying the quality and integrity of deep foundations was in its infancy, its growth constrained by the technology, or lack thereof. Some visionary engineers of the time understood the physics of the potential methods, and therefore the possible capabilities, but were frustrated by the lack of technology to work with. Electronic equipment was mostly analog, and the few digital data acquisition systems that were available had such slow sampling rates that they were incapable of recording rapid event sequences or short duration events such as those used in modern integrity tests. For example, Jean Paquet, a leading research engineer at the French National Construction Institute, (Centre Experimentale de Recherche et d’Etudes du Batiment et des Travaux Publics, or CEBTP) patented the frequency-based analysis procedure for the Transient Dynamic Response (TDR) method, aka Sonic Mobility or Impulse Response, in 1974, but it was not until 1977 that analog data acquisition systems became fast enough to turn his theory into a reality."

Jan 1, 2017

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By Sara Anderson, Rachel Nicholls, Tim Chapman, Janice Windle

"In city center sites around the world, and in particular in London, foundation reuse is becoming increasingly widespread as the ground is filled with detritus from previous developments. This paper sets out a systematic framework to consider the need for and benefits of foundation reuse and key issues to be resolved for foundation reuse to be successfully adopted on redevelopment projects. Once foundation reuse has been identified as a potential foundation solution there are several key stages in the design and construction process where the decision to reuse foundations needs to be assessed. The paper concludes by emphasising the importance of ensuring that the foundations being installed now can more easily be reused in the future.INTRODUCTIONThe concept of re-using foundations is not new, and has been adopted on an isolated project-byproject basis for many years. However, over the past decade, interest in the potential of reusing existing piles and caissons within Europe has increased significantly, with a growing interest in the United States of America and Japan. The need has been driven by necessity: on many urban sites the space available for new foundations diminishes with each new set of piles, and these problems can only grow in the future.Initiatives such as the European Union's RuFUS (Re-use of Foundations for Urban Sites) research project have resulted in identification of the key issues for technical viability and risk that have previously hampered potential foundation reuse projects.There is a need to define a systematic approach to the reuse of foundations so that the risks associated with reuse can be identified, managed and mitigated. This requires improvements in knowledge to provide confidence in the long term behaviour of the foundation support and address the risks involved in reusing existing foundations to overcome perceived obstacles in making foundation reuse a realistic option for many sites."

Jan 1, 2005

By Seiji Mizutani, Hirofumi Taguchi, Makoto Yoshida, Hidenori Takahashi, Naotoshi Shinkawa, Kazuo Konishi, Yoshiyuki Morikawa, Masaya Kawata

"The lattice-shaped cement treatment method has been used to improve the seismic performance of liquefied sandy soil in Japan. The efficacy of the method has been confirmed by the huge earthquake in Japan. In the present study, a new method to improve sandy ground by using the lattice-shaped cement treatment method is proposed as a liquefaction countermeasure. It is the floating-type and lattice-shaped cement treatment method, where cement treated soil is not fixed to an un-liquefiable stratum. In this method, a fixed-type structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were firstly conducted to confirm the mechanism of the new method. Secondly, a series of centrifuge model tests were performed to demonstrate the effect in a proto-type scale's stress condition. The analyses and model tests confirmed the effect of liquefaction countermeasure of the new method.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2015

By Michael Perlow

Helical screw piles in use since 1838 are routinely used for energy, transportation, municipal, industrial, marine and coastal infrastructure as well as for excavation support, environmental remediation, and foundation repair. They are especially well suited for work in constrained areas, renovations and structure retrofits. Helical pile design procedures over the past 10 years have gone through a remarkable evolution with the establishment of the 2007 AC358 Helical Pile Acceptance Criteria and inclusion of helical screw piles in the 2009 International Building Code (IBC). New 2009 IBC building code requirements and AC358 Acceptance Criteria are presented along with advances in helical pile design procedures, installation, QA/QC, and recommended load test verification criteria. Use of helical smart piles to validate helical pile design and verification of ultimate pile capacity is highlighted.

Jan 1, 2011

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By Clayton A. Signor

Abstract: Expansive soils cause more damage to structures annually than a combination of other major natural disasters. Because of the cost to our society, all means and methods need to be fully explored to mitigate the problems associated with expansive soils. This study will present a foundation design approach that is underutilized in this application, driven piles. The main objective of the study is to present pile test results and analysis from four driven pile project sites in three types of expansive soils found in central Texas: Del Rio formation, Taylor/Navarro formation, and expansive alluvium. High strain dynamic pile tests were conducted on each of the four studies with rigorous signal matching analysis from the CAse Pile Wave Analysis Program (CAPWAP). Ultimate pile capacities ranged from 73 to 311 kips with an average of 61% of the total capacity coming from the pile shaft and were two to six times the structural capacity needed. Allowable loads calculated from Modified Gates dynamic formula best modeled allowable test results. Average unit skin frictions ranged from 0.50 to 4.71 ksf. Restrike pile tests of 1 to 17 days after initial driving reported 30 to 100% shaft capacity gain. All open-ended pipe piles driven produced soil plugs ranging from 4 to 14 feet thick. Small diameter, thick-walled, open-ended pipe piles reached penetration of twice the depth of designated zone of seasonal moisture change without problem. The observed production rate of the driven piles was on average 8 minutes, which implied daily production of 15 to 40 piles. Predrills or augered holes should be specified for underground obstructions found in soil investigation.

By Remco Offenberg, Marcel Bielefeld, Martijn van Delft

The question of the continued suitability of existing foundations arises when the function of the superstructure changes. This can occur when the superstructure is replaced or when the existing structure is expanded, leading to higher loads on the existing foundation. Quite often it is a challenge to define the suitability (with respect to integrity, bearing capacity or both). The lack of information on the existing foundation (such as pile dimensions, installation records, original soil investigation, design calculations, etc.) makes it frequently seemingly impossible to assess whether the foundation or foundation elements can be re-used. The paper outlines the tools available to an engineer to evaluate existing foundation piles for potential re-use. The paper illustrates the application of these tools through a few case studies from The Netherlands, including the evaluation of a 400 years old bridge foundation to address increasing traffic loads.

May 1, 2022

By Teresa M. Bodas Freitas, Arianna Lupattelli, Peter J. Bourne-Webb, Diana Salciarini, Martina Zito, Donatella Sterpi

The thermomechanical response of thermally-activated (TA) piles under monotonic thermal loads is quite well understood and the remaining uncertainties relate to the effect of long-term, cyclic loading of individual TA piles and pile groups. Recent studies undertaken by the authors have provided insights into the behaviour of TA pile foundations undergoing cyclic thermal loading. Despite their simplicity, the analyses show that key aspects of the observed response of piles in sand, under cyclic thermal loading can be reproduced, providing confidence in the outcomes of the analyses. The studies examined isolated piles and pile groups, and concluded that irrecoverable thermally-induced settlement may be mitigated through the choice of an appropriate margin of safety on the pile shaft resistance under service mechanical load conditions, and the maximum thermal stress can also be readily estimated. This paper consolidates these works and provides guidance regarding the safe geotechnical and structural design of the piles, then looks towards the remaining issues around the safe provision of thermally-activated pile foundations.

May 1, 2022

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By Ali Nasirian Ph. D., Gabriel Carvajal

To facilitate the safer and more secure transportation of inmates from San Diego Central Jail to the new San Diego Courthouse, the County of San Diego committed to building a new transfer facility as part of the downtown developments. The transfer facility includes a three-story underground structure adjacent and connected to the Central Jail and a 60-ft deep, 23-ft diameter, 320-ft long tunnel. The tunnel starts at County Jail, passes underneath Western Regional Detention Facility (Old Jail) and, ultimately, connects to the State Courthouse. Condon-Johnson & Associates, Inc. (CJA) was selected to install the temporary shoring shaft for the underground structure as well as three arrays of canopy pipes to support the tunnel’s Sequential Excavation Method (SEM) construction. CJA installed the rectangular 56-ft deep access shaft shoring with three levels of bracing, and a combination of secant piles, soldier piles, and timber lagging. The shoring also included a sliding bridge at top to provide access for trucks to enter and exit from county jail during the duration of construction. Following shoring and shaft excavation, CJA installed and grouted 7-5/8” dia. canopy pipes in 3 reaches, parallel to the longitudinal design line of tunnel with a slight lookout angle. CJA installed 24 each canopy pipes, 99-ft from face of shaft at reach 1, 21 each, 80-ft length canopy pipes at reach 2, and 21 each, 75-ft length pipes at reach 3. CJA confirmed canopy pipe alignment via Inertial Sensing Gyro. To mitigate the possibility of settlements caused by the tunneling operation underneath Old Jail strip footing and grade beams, CJA also performed void fill grouting. Sleeve port grout pipes (SPGP’s) were installed inside the Old Jail basement and grouted with the use of packers as the tunneling operation passed underneath the Old Jail. In detailing various aspects of the construction, this paper aims to magnify the innovative solutions for shoring, canopy pipe installation and void fill grouting challenges as well as the state of the art quality control measures undertaken by CJA.

Oct 1, 2022

By Pawan L. Sethi

Design and construction of deep foundations and basements is increasingly becoming more complex, as the density and frequency of urban development increases. This growth brings various associated challenges in the form of design considerations and construction challenges. This paper discusses some of the challenges routinely encountered as well as some specific complications in this area, based on author’s experience gained through exposure as specialist contractor (designer), consultant and specialist consultant, along with some information on how these challenges were overcome. The paper highlights some of the key aspects of design coordination and importance of having an awareness of the overall perspective. Examples will be used to illustrate practical problems and the approaches used to respond.

Nov 1, 2022

By Tatiana Tronda

"The territory of Belarus is characterized by nonhomogeneous ground conditions. In some cases soft ground layers can reach tens of meters in depth. Application of piles and other conventional foundations is rather difficult and expensive in such complicated conditions. Alternatively for the first time dry concrete columns were applied to improve the saturated soft soils at two sites. As there is no design methods for calculation of bases improved by dry concrete columns static penetration and static load tests were carried out to check the bases on availability. Considerable increase of toe resistance and Young modulus was achieved for all types of soil. Practical application, technology and test results are described in the paper. According to comparative calculations the cost of foundations on the base improved by dry concrete columns can be 32-75% lower than the cost of conventional pile foundations depending on ground conditions.INTRODUCTIONPile foundations, sand cushions or dewatering are usually applied in complicated ground conditions which are caused by presence of saturated soft soils. If the depth of soft soils reaches 20 m or more, conventional foundations have limited application, high labor and construction cost. A rational solution in such conditions is a ground improvement of upper soft soils. It allows the loads to be transferred on upper ground layers and the stresses to be dissipated considerably before reaching underlying soft ground layers.One of the effective ground improvement methods for saturated soft soils is the reinforcing by dry concrete columns (Fig. 1). The method allows saturated soft soils to be compacted and be drained at the same time. As a result strength and deformation characteristics of natural soils improve (Tronda 2013, ?????? 2014).Unfortunately, there is no design and computing methods for the ground improvement by means of dry concrete columns. However, at present the methods are under development on the basis of theoretical and experimental researches.TECHNOLOGYThe dry concrete columns are fulfilled in pressed wells according to technology of vibrostamped piles. Wells are pressed by vibratory hammer with the closed ended casing (Fig. 2) that provides compaction of surrounding soft soils. Then the casing is filled with dry concrete mix (Fig. 3). The casing end remains on the design depth and the casing is removed by vibratory hammer. The removing of the casing with vibration enables compaction of dry concrete mix inside the well. Dry concrete mix drains surrounding saturated soft soils improving its properties and the compaction speeds up the consolidation process. Over time the dry concrete columns fasten absorbing water from surrounding saturated soft soils that is need for hydration of cement (Fig. 4, 5)."

Jan 1, 2016