Search Documents

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By P. R. A. Andrews

"The sillimanite group minerals, kyanite, sillimanite and andalusite are identified as alumino-silicate minerals with the common chemical composition AIP3.Si02' so that each possesses similar physical properties. Kyanite is the most abundant mineral and mainly occurs in Quebec, Ontario and British Columbia; sillimanite occurs in Ontario and Manitoba; and andalusite in Nova Scotia. The main use for the sillimanite-group minerals is in refractory applications for the production of refractory bricks and shapes. In refractory applications, the main performance criterion is the relative percentage of mullite formed within the material during firing. This phase gives a greater degree of resistance to creep deformation and slag attack, and improves the ability of the refractory to withstand high temperatures under load. The beneficiation of refractory silicate minerals has been the subject of many investigations at CANMET, and the former Mines Branch. Eighteen kyanite, two sillimanite, and three andalusite evaluation studies were conducted between 1933 and 1987. A review of some of the more important studies is presented, which includes information concerning mineralogy, beneficiation methods and flotation data."

Jan 1, 1995

By J F. Davies

A review is presented of the fundamental differences between the Superior and Churchill geologic provinces. Structure, lithology, grade of metamorphism and a single recent age determination suggest that the Flin Flon -Snow Lake and Lynn Lake belts are remnant blocks of originally Superior rocks lying within the Churchill province. Major mineral belts occur along the main boundary between the Superior and Churchill provinces (the Thompson -Moak Lake nickel belt) and within the remnant Superior blocks inside the Churchill province (Fiin Flon -Snow Lake and Lynn Lake). During the Hudsonian orogeny, metamorphic gradients must have existed across the Churchill-Superior boundary and between the remnants of Superior rocks and the enclosing gneisses of the Churchill province. It is possible that not only the unusual nickel deposits of the Thompson belt but also the base metal deposits of the Flin Flon -Snow Lake and Lynn Lake districts are due to redistribution, or diffusion and migration of metals to areas of lower-grade metamorphism during the Hudsonian orogeny.

Jan 1, 1964

By J. Brent Hiskey

At present, approximately 80 % of the worlds mine production of copper is achieved by smelting and electrorefining. The principle aim of copper electrorefining is to satisfy the large demand for extremely pure copper. It is remarkable that high quality copper cathodes with the required purity (99.99+% Cu, ASTM B115-10) and structural characteristics (i.e. deposit density and morphological texture) are produced from impure copper anodes dissolved in electrolytes containing a variety of impurities. This is accomplished with the proper control of operating parameters such as: current density; temperature; copper and sulfuric acid concentration; agitation; substrate preparation; and the application of electrolyte additives. The basic elements of the electrolysis of copper have not changed significantly over the past 150 years since the early developments of James Elkington. Importantly, our fundamental understanding of the underlying electrochemistry has advanced considerably. This is especially true regarding our knowledge of the mechanistic role of additives during the electrocrystallization of copper. This is a very complex subject and modern electrochemical techniques and the development of surface characterization and imaging instruments has helped immensely in our ultimate understanding of how additives control the deposit structure and morphology. The purpose of this paper is to review the historical development and application of electrolyte additives in copper electrorefining and to examine our current knowledge regarding their use. INTRODUCTION The first transatlantic telegraph cable was completed in August 1858. Regrettably, this cable failed shortly after the initial connections. After several more failed attempts, improvements in materials and copper quality resulted in successful communication between Europe and America on July 28, 1866. In many ways this hallmark event demonstrated the need for high purity copper. The first copper refinery in the world was commissioned in May 1869 in Pembrey, South Wales by partners Josiah Mason and James Balleney Elkington. (Historical Note). The 1865 and 1868 British patents issued to James Balleney Elkington were the foundation for the first commercial production of high purity electrolytic copper (Elkington, 1865, 1869, 1870). This important achievement was made possible primarily by the invention of the dynamo which was based on the fundamental operating principles advanced by Michael Faraday. A symbiotic relationship between copper refining and the dynamo was henceforth established. The dynamo provided electric current for electrolytic refining of copper and the electrorefining tankhouse provided pure copper which was required for the generation and transmission of electricity.

Jan 1, 2019

By A. J. Williams

"Whenever a decision is made to bring a mineral deposit into production, the Owner in actual fact has decided to convert substantial sums of capital into productive capacity with the intenti6n of making a profit from such conversion.Escalating costs of construction, frustrating and costly delays in comp1etion, the increasing tempo of technological change and the increasing size and complexity of mineral processing projects have convinced Owners that the best way of implementing their capital must be sought and utilized. This requirement has stimulated a search for ways and means of applying modern management techniques to the design and construction of mineral processing plants.This search by consulting firms has resulted in the evolution of the concept of project management and the development of planning and con trolling techniques with the result that Owners can seek and obtain better assurance that their project objectives will be fulfilled.This paper will attempt to outline how a mineral processing plant can be brought into production through the implementation of project management techniques.Definition And Objectives Of Project ManagementThe design and construction of mineral processing plants is subject to the restraints of three inter-related parameters -Quality, Cost and Time each of which influences and is influenced by the other two.Project management is a technique where the Owner delegates complete responsibility to a single organization for all phases of a project (design, procurement, construction and commissioning) for the above parameters but retains freedom for major decision making. Normally, the consultant under-takes full responsibility for all phases, but partial project management services can be provided when the Owner so desires.The objective of project management is first to devise and define and then to implement a program in which the relationship between the three parameters of Quality, Cost and Time is optimized, i.e., the desired functional and other requirements are attained (but not exceeded) at the lowest practicable overall cost in the shortest practicable time. The measure of success of a project lies in the degree to which this objective is achieved."

Jan 1, 1974

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel/truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By DAVID C. MILLER

Barite deposits occur worldwide and in a variety of geological environments. In recent years, several deposits of barite and barite-lead-zinc have been discovered in northern British Columbia, Yukon Territory and Alaska. Most are associated with Devonian-Mississippian age sediments, and many are syngenetic, bedded-type deposits. The Mel is a barite-lead-zinc deposit; it lies within Lower Cambrian strata and appears to be of epigenetic replacement origin. Figure I is an aerial view of the property from the south. Observations herein described are based largely upon field work, megascopic studies and two recent B.A.Sc. theses (Biasucci 1979, Rennie 1979).

Jan 1, 1984

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By R. W. Pugh, S. L. Ma

"High carbon rods are typically used as the grinding media in rod mills. Usually an AISI I 090 grade of steel is used which provides the high hardness needed for abrasion resistance and sufficient toughness to prevent rod breakage.Work to improve performance in the past has mainly concentrated on increasing the hardness for improved abrasion resistance. This has been accomplished by adding alloys to the steel which uniformly increase the hardness across the rod section.However uniformly increasing the hardness of the rod produces a more brittle product and at high hardness l1evels can lead to rod breakage problems. Heat treatment processes can be used to selectively increase the surface hardness to high levels while maintaining the core at lower hardness levels to give a product that wears slower without breakage. AltaSteel has developed and mill tested a higher hardness heat treated grinding rodThis paper describes the development of a simple model to predict performance improvement with different hardness profiles and the AltaSteel heat-treated grinding rod process. Mill characteristics of the Endako operation are summarized and predicted performance improvements based on hardmess are compared to the approximate 25% achieved in trials running since July, 1991 at this mill. Early results of other mill trials are also presented.INTRODUCTIONAltaSteel, in Edmonton is a major supplier of grinding media. We have a strong desire to continually increase the quality and performance of our products and thereby improve the efficiency of our customers' processes. In the area of grinding rods, we wanted to produce a product with a significant improvement in wear rate. Second to energy, rod consumption usually represents the next highest cost in processing. This paper presents our development of a heattreated grinding rod that has reduced consumption by about 25% in trials to date."

Jan 1, 1993

By R. Hagiwara, S. Kobayashi, K. Yasuda, T. Nohira, K. Kondo

To establish a process for the electrochemical recovery of rare earth elements from used magnet scraps, the electrochemical formation of RE-Ni alloys in molten NaCl-KCl-RECl3 salt at 973 K was investigated. Cyclic voltammetry and open-circuit potentiometry indicated the formation of several phases of RE-Ni alloys. The formation potential for each RE-Ni alloy phase was determined from the results of scanning electron microscopy and X-ray diffraction of alloy samples prepared by potentiostatic electrolysis of a Ni plate electrode at various potentials. The optimum electrolysis conditions for the separation of Nd, Dy, and Pr are discussed.

Jan 1, 2014

By R. J. Rotzinger, K. W. Major

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By Ben Cottrell

In this paper technical drilling is referred to as the process of collecting engineering and metallurgical parameters for subsequent mine design considerations. Throughout the development of a mineral exploration property there are various opportunities to ?piggy-back? technical drilling onto the routine exploration drilling process, helping to reduce future costs and delays associated with re-drilling and missing information. This article is written from the engineers and metallurgists point of view, to outline some best practices for exploration borehole planning and technical data collection requirements.

Aug 1, 2013

By W. H. Hastings

Introductory In the amount of her coal reserves, Saskatchewan ranks third among the provinces of the Dominion, with a total, as estimated by D. B. Dowling, of 59,812,000,000 tons. All the coal so far discovered in the Province is lignite, and it would appear unlikely that bituminous or higher grade coals exist. General Occurrence of the Coal The location of the coal-bearing formations in Saskatchewan is shown on the accompanying map. It will be seen that the areas lie principally in the southern part of the Province. The more darkly shaded areas indicate locations where development is taking place, or where coal-seams are known to occur, either through outcrops in valley-sides or through having been encountered during boring operations. The coal-seams are not necessarily continuous throughout the shaded areas, but in all pans of these there are coal possibilities. It is quite possible that small outliers of the coal-bearing formations may occur further north in the Province, but, generally speaking, coal is not likely to be found outside the shaded areas.

Jan 1, 1929

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Thorium is frequently the main radioactive element in rare earth ores and is a resource that can potentially substitute for uranium. Thorium must be separated from rare earths in order to obtain products with low radioactivity. There are abundant resources of thorium in the rare earth ores in China, especially in Baiyunebo mixed ores. As an associated element coexisting in rare earth ores, thorium is, or can be, separated from rare earth concentrate, iron concentrate, as well as from waste water and slag to achieve recovery of thorium. The methods of separation include ion exchange resin, liquid-liquid extraction, and liquid-solid extraction. TBP extraction has been the main method applied to separate thorium by domestic and foreign scholars. This paper presents a comparison of different processes for the separation of thorium from rare earth ores, especially Baiyunebo mixed ores, single bastnaesite and monazite ore, and provides suggestions for the future recovery of thorium resources.

Jan 1, 2014

By Selvia Tourn, Liliana Castro

"Abstract - Argentina, a large country with an important agriculture industry, needs an ever-increasing amount of phosphorus and potassium, as essential elements for plant growth. Current requirements are met from imports, but potential resources exist in Argentina. For example, several phosphatic occurrences are known in paleo-marine basins, the most significant of which are in Tertiary units in Patagonia. In addition, two types of potassium deposits are also known in Argentina: evaporite deposits in the Neuquén Basin at depths of 750 m to 1500 m contain 22 to 25 wt% K2O equivalent; and glauconitic sandstone containing about 6 wt% K2O has been identified in Patagonia.Several experiments were undertaken to test unprocessed phosphate rocks as slow-release, direct-application fertilizers, with good results. In addition, it is proposed that direct application of glauconitic sands would provide an efficient and economic alternative source of potassium. Tests with glauconite samples are still in progress. The existence of both phosphate and glauconitic rocks in Patagonia suggests that development of an extractive industry for these materials would not only help Argentina approach self-sufficiency in fertilizer usage, but also assist in the socio-economic development of this region."

Jan 1, 2003

By J. A. Orr

The details connected with the mining and subsequent handling of Creighton ore were fully covered in a paper presented to the Institute in 1920. The following brief notes describe certain phases of the present practice and show wherein it differs from the practice at that time. These may be summarized under the following headings. (a) Recovery of pillars. (b) Drawing the ore. (c) Change from sub-level tramming to branch-raise system. (d) Chute construction. The present stoping practice is the same as formerly, i.e., fiat-backed shrinkage stopes of 60-foot width, between rib pillars of 15-foot width, extending from the footwall to the hanging-wall. Formerly, when these stopes were completed to the stopes above, they were drawn empty of broken ore, and the 15-foot rib pillars were caved into the stopes and drawn off through the same chutes as were used to draw the ore from the stopes.

Jan 1, 1926