Search Documents

By D. P. Wilkinson

Flow field design is critical to determining fuel cell performance with respect to operating conditions. Flow fields are normally designed around their maximum power operating point with the goals of maximizing performance and minimizing pressure drop between the inlet and outlet of the flow field. At lower power pressure drop is reduced, and water management and reactant distribution issues can occur over the active area as well as issues with cell to cell reactant distribution in the fuel cell stack. Flow fields have fixed flow channel geometries and fixed active areas which determine the reactant flow characteristics over the operational range of the fuel cell. In this paper we discuss some of the benefits of a new approach of changing the flow field active area with changing operating conditions. Such benefits for future fuel cell designs could include improved cell performance and stability, improved cell to cell reactant distribution, reduced low current density failure modes, and overall system advantages.

Jan 1, 2005

By M. M. Papic

"This paper describes the Sasol coal liquefaction process, as used in South Africa. It covers coal supply, coal gasification, gas purification, Fischer-Tropsch synthesis, the major utility systems involved and the economics of the process.IntroductionThe Sasol coal liquefaction process is based on Fischer-Tropsch synthesis of liquid fuels from carbon monoxide and hydrogen, which are in turn obtained by gasification of coal with steam and oxygen. The process is shown schematically in Figure I.The first step in the process is coal preparation, in which the coal is crushed and screened to a 3-50 mm size for gasification on one side and to -3 mm size for steam and power production on the other. Oxygen needed for coal gasificatoin is produced in the air separation plant.Coal is gasified under pressure by steam and oxygen in the Lurgi gasification plant, where raw, impure gas is produced . The raw gas is first washed in a scrubber with a circulating gas liquor, heat is then recovered from it in a waste heat recovery boiler and the gas is further cooled for purification. Water-insoluble materials (tar oils) in the gas liquor are separated from aqueous solution and sent to tar refining for the recovery of tar products. The aqueous portion of the gas liquor goes to a Phenosolvan solvent extraction process, where phenols and ammonia are recovered. Water then proceeds to the effluent treatment plant.The scrubbed and cooled raw gas goes to a Rectisol gas purification plant, where all components other than hydrogen, carbon monoxide and methane are removed as completely as possible by absorption in refrigerated methanol. The acid gases (CO2, H2S) stripped from the methanol in the Rectisol unit are processed in a Stretford plant for recovery of sulphur. Regenerated methanol is returned to the process. The purified synthesis gas is passed to the fluidized-bed Synthol reactors, where Fischer-Tropsch synthesis reactions take place.The synthesis products are recovered in a product recovery unit as separate streams of decant oil containing higher-molecular- weight hydrocarbons, light oil comprised of lower-molecular- weight species, the aqueous stream containing water solubles, a C3/C4 stream, a C2 stream , a methane stream and a hydrogen-rich stream. Most of the hydrogen is recycled to the Synthol reactors; a major portion of the methane is reformed to hydrogen and carbon monoxide for recycle; the C2 fraction goes to an ethylene plant; and liquid streams proceed to the product refinery.The product refinery is used to upgrade and purify the Synthol products to specification fuels and chemicals.Sasol l, the first coal liquefaction plant in South Africa , was built in 1955. It is still operating and has a product output of about half a million tonnes per year. The Sasol II plant is in a commissioning stage and will be in full operation in 1981. It is about five times the size of Sasoll. It uses over 12 million tonnes of coal and produces more than 2 million tonnes of saleable products annually (1,2,3). The Sasol llI plant, which is a mirror image of Sasol II, is under construction and scheduled for completion in 1983."

Jan 1, 1981

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By Fadi Layyous Gedeon, David Hatton, Solomon Mogashoa, Tuhin Banerjee, Faisal Aljohani

The adoption of innovative technologies in mineral processing often raises concerns about complexity and integration. However, Woodgrove’s Direct Flotation Reactor (DFR) technology at Barrick’s Jabal Sayid copper concentrator provides a different perspective. This paper outlines the smooth integration of DFR technology from piloting to full-scale commissioning, showcasing how easily the cells were brought online. Installed in a cleaner scalper role, DFR cells at Jabal Sayid upgrade re-ground rougher concentrate to final concentrate in one stage. Despite processing challenging ore, the DFR cells delivered concentrate grades that consistently exceeded expectations. The commissioning process was straightforward with minimal hurdles, highlighting the technology's user-friendly nature. This paper advocates for a shift in perceptions about new technologies in mineral processing. The success of DFR technology at Jabal Sayid demonstrates that “different” doesn’t mean “difficult.” By focusing on ease of commissioning and operational integration, innovative solutions can enhance processes, improving efficiency and productivity in the mining industry.

May 4, 2025

By C. S. Liao, S. L. Wang, C. H. Yan, F. X. Cheng

A significant development in the theory of countercurrent extraction will be presented in this article. A new term in countercurrent extraction process analysis, "Adjacent Stage Impurity Ratio" (ASIR), is proposed, and its expression is deduced. Furthermore, based on the term together with mass balance and extraction equilibrium, the conditions where a given countercurrent extraction separation operation can have minimum amounts of both extracting solvent and scrubbing agent solution can be estimated, and the equations of the two minimum amounts can be deduced. It was found that the equations for a two-component separation using a single aqueous or organic feed are exactly the same as they appeared in the theory initially established in the 1970s. Unlike its earlier version, the present derivation does not involve feed-stage-composition hypothesis, and also has the advantage of dealing with a double-feed system where both aqueous and organic feeds are simultaneously employed whereas the earlier theory can only analyze a separation using a single aqueous or organic feed.

Jan 1, 2014

By L. A. M. Castro

As Canadian mines progress to greater depths, magnitudes of induced stresses increase, becoming high enough to cause rock mass damage and failure during excavation. In addition, depending on the orientation of key geological structures in relation to the in-situ stresses, induced shear loading can be developed on these structures, creating the potential for: a) remobilization of existing geological structures, b) formation of new seismically active structural zones, created through rock mass damage and coalescence along such structural zones, and/or c) interaction between existing and newly created structures. Numerical analyses were carried out to investigate four possible factors that might cause fault slip on controlling structures, namely: (a) unclamping, (b) day-lighting, (c) stress rotation and (d) pillar shear. Application to an underground mine in the Sudbury Basin allowed verification of these factors and the proposal of two alternative mine planning methods to limit fault slip on key structures: (1) pillar clamping and (2) stope sequencing.

May 1, 2009

By Yan Qun, Chen Xiao-ming, Ma Pei-long, Luo Xian-ping, Luo Cai-gui, Feng Bo

The effect of leach promoting reagent LPF on the leaching process of a weathered crust elution-deposited rare earth ore has been investigated and the mechanism is discussed. The result shows that the leach promoting reagent LPF can enhance the leaching extraction of rare earth ore effectively. With the addition of LPF to the lixiviant at a concentration of 0.1%, the leaching extraction increased by more than 8%, the ammonium sulfate concentration could be decreased by 25%, and the leaching liquid/solid ratio reduced by 34%. The mechanism analysis shows that LPF can react with rare earth ions and form soluble coordination compounds, thus reducing the activity of the leached rare earth ions, increasing the concentration difference for ion diffusion, and promoting the rare earth leaching process. These results will hopefully help point to a new approach to making the leaching process of low-grade weathered crust elution-deposited rare earth ore more efficient and with lower lixiviant consumption.

Jan 1, 2014

By T. Macpherson

Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By S. D. Normani

A Deep Geologic Repository (DGR) for Low and Intermediate Level radioactive waste has been proposed by Ontario Power Generation for the Bruce Nuclear site in Ontario, Canada. The DGR is to be constructed at a depth of about 680m below ground surface within the argillaceous Ordovician limestone of the Cobourg Formation. The objective of this paper is to apply paleoclimate boundary conditions to a regional-scale groundwater flow model for the DGR site and to describe the influence of glacial loading and unloading on flow system evolution using the FRAC3DVS-OPG flow and transport model. The regional-scale domain encompasses an area of 18,775km2 extending from Lake Huron to Georgian Bay in southwestern Ontario, Canada. From a hydrogeologic perspective, the domain can be subdivided into a shallow zone, an intermediate zone, and a deep zone comprised of the low-permeability units of Ordovician and the more permeable Cambrian where present. The deep groundwater zone is characterized by units containing stagnant water having high concentrations of total dissolved solids (TDS) that can exceed 300g=L. The high TDS values at depth require density-dependent coupled flow and transport calculations within FRAC3DVS-OPG. The computational sequence involves the calculation of steady-state density independent flow that is used as the initial condition for the determination of pseudo-equilibrium for a density-dependent flow system that has an initial TDS distribution. The 1,000,000 year pseudo-equilibrium heads and brine concentrations are used as the initial condition for the paleoclimate simulations. Over the past 900,000 years, the Canadian Shield has experienced approximately nine episodes of complete glaciation. During the glaciation cycles, the entire Canadian land mass has been covered by a series of continental ice-sheets whose maximum thickness reached 4 km and whose southern extents reached, in some cases, beyond the present-day Canada-U.S. border. The glaciation phase of a single glaciation-deglaciation episode is typically 90,000 years in duration, while the deglaciation portion proceeds relatively rapidly and has an average duration of approximately 10,000 years. Output from the University of Toronto Glacial Systems Model, a continental scale North American glacial reconstruction of the most recent 120,000 year glaciation event developed by W. R. Peltier, is used to supply the paleoclimate boundary conditions used in this paper. Permeabilty reductions due to the presence of permafrost are also considered in the paleoclimate simulations. This paper will demonstrate that the choice of rock properties can significantly affect residual pore water pressures within the rock matrix, as well as the migration of glacial meltwater.

May 1, 2009

The use of roof bolting gave promise of substantial economic benefits to Continuous Miner operations at Michel Colliery. As the first step in the adoption of bolting, 142 anchorage tests, employing six types of anchor shells, were made in three mines. Significant differences were found in the anchorage capabilities of the various shells and the various roof rocks. Introduction S PORADIC attempts at roof bolting had been made at Michel Colliery over a period of ten years. Results were indifferent or inconclusive. A concerted effort was not made, because a compelling need for bolting did not exist. By 1962, however, the advent of Continuous Miners had brought a new significance to roof bolting and, at the same time, the increasing price and scarcity of mine timber made bolting materials more competitive in cost. A fresh appraisal of bolting, therefore, became justified and necessary. The potential benefits of roof bolting at Michel are several.

Jan 1, 1963

By L. A. Melis, J. W. Rowson

"Cluff Mining has successfully operated a gold recovery plant at its Cluff Lake operation in northern Saskatchewan to recover gold f rom Phase 1 uranium leach tailings. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-inpulp, gold recov ery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and operating data and metallurgical results from the operation are provided.INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 per cent by Cameco and 80 per cent by Amok Ltd. /Ltée. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake, 700 km north of Saskatoon, capable of processing 300 000 tonnes o f ore to produce about 4 000 000 lb UPs (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""0"" uranium orebody from 1980 to 1983. The leach tailings from the Phase I mill operation were found to contain elevated level s of gold . These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the""0"" orebody .During the Phase I operation some 6475 tonnes of leach tails were produced and stored in a total o f 2916 large concrete containers (vaults). This method of storage was, at the time, deemed to be the preferred method of temporary storage for the tailings.This temporary storage of high-grade gold tailings facilitated the reclamation and reprocessing of the leach tail s for gold recovery. The primary reason for reprocessing the Phase 1 leach tails was to provide for long-term permanent disposal of the material as an admixture with Phase II tailings in the Cluff Lake tailings disposal area. Although there was limited tonnage, the high gold content in the material made the in stallation of a gold recovery circuit economically justifiable."

Jan 1, 1989

By P. R. A. Andrews, R. K. Collings

"In cooperation with le Ministère de l'Énergie et des ressources, Québec, le Centre de Recherches minérales, Sainte-Foy, Québec, and various silica producers, selected deposits of Quebec silica were identified in the southern region of the province and sampled to provide material for evaluation as glass and foundry sand by CANMET. The samples included both sandstone and quartz/quartzite. Head sample analyses ranged from 94.66% to 99.54% SiO2, 0.038% to 0.230% Fe2O3, and 0.16% to 4.51% Al2O3.Impurities included pyrite, iron oxides, and iron staining on quartz grains; carbonates as calcite; and alumino-silicates as clay and/or feldspar. Processing included size reduction to grain size, about 600 µm, by jaw, roll and cone crushers, and grinding in a muller-mixer. Removal of fines was achieved by attrition scrubbing and washing. Further removal of impurities was achieved by reverse flotation of iron oxide and alumino-silicate minerals employing both anionic and cationic collectors. Flotation resulted in a substantial improvement in the quality of most sands, the quartz concentrates analyzing 99.08% to 99.80% SiO2, 0.014% to 0.048% Fe2O3, and 0.06% to 0.49% Al2O3. Removal of iron oxide minerals was also investigated using the Sala HGMS. Iron oxide analyses of the non-magnetic fractions were comparable to the iron oxide analyses of the quartz concentrates obtained by flotation, 0.013% to 0.054% Fe2O3. On the basis of the samples submitted, silica from 5 of the 6 deposits studied has potential as source material for glass sand. Foundry tests showed that 3 of the 4 samples submitted for evaluation have potential as foundry sand."

Jan 1, 1987

By Alok Porwal, E. J. M. Carranza, M. Hale

Abstract- Approaches to mineral potential mapping based on weights of evidence generally use binary maps, whereas, real-world geospatial data are mostly multi-class in nature. The consequent reclassification of multi-class maps into binary maps is a simplification that might result in a loss of information. This paper describes results of using multi-class evidential maps in an extended weights-of-evidence model vis-à-vis results of using binary evidential maps in a simple-weights-ofevidence model. The study area in the south-central part of Aravalli province (western India) hosts a number of SEDEX-type base metal deposits in Proterozoic supracrustal rocks. Recognition criteria for base metal deposits were represented as both multi-class and binary evidential maps. The known mineral deposits were divided into two subsets, viz., the training and the validation subsets. The training subset was used to calculate, for the evidential maps, the weights, contrasts, and posterior probabilities and their variances. The distributions of expected frequencies of base metal deposits estimated from the posterior probabilities and the observed frequencies were compared using standard goodness-of-fit tests to verify conditional independence of the input evidential maps. The posterior probabilities from both the models were mapped and interpreted to classify the study area into zones favorable, permissive, and non-permissive for base metal deposit occurrence. As compared to the simple weights-of-evidence model, the extended weights-of-evidence model results in more robust and finely differentiated posterior probabilities in favorable and permissive zones and has a better prediction rate. The results also reveal that the statistical properties of the weights of evidence, the contrasts, and the posterior probabilities are not significantly degenerated by using multi-class evidential maps in weights-of-evidence modelling.

Jan 1, 2001

By Ngonidzashe Chimwani, David Glasser, Diane Hildebrandt

"Milling circuits play an important role in achieving the desired product; tonnage, size distribution and properties, since they are directly linked to the comminution energy consumption for the whole process. A grinding model with a mathematical simulation was developed for an open milling circuit with a scalped feed from a hydro-cyclone. The circuit was optimized by determining the optimal conditions in terms of energy consumption which would produce a floatable product having a desired size range (i.e. -75 +9 µm) for a platinum-bearing ore. The simulation results showed an operating region comprising the best combination of the ball filling and mill speed to achieve the highest production of a floatable size class, with the minimum energy consumption.INTRODUCTIONBall milling is usually conducted in closed circuits in order to achieve a desired product size without material overgrinding. The technological importance of optimising milling circuits cannot be overemphasised (Toneva and Peukert, 2007). Previous work has brought significant insights into the benefits of modelling milling circuits (Austin et al., 1984; King, 2012; Toneva and Peukert, 2007). However, the ability to model these circuits is dependent on the performance of the classifiers and the fidelity of the grinding mill model used compared to the actual circuit (Toneva and Peukert, 2007). Austin et al. (1984) identified five types of milling circuits as shown in Figure 1 namely; the grinding circuits employing mill in an open circuit, normal closed circuit, reverse closed circuit, open circuit with scalped feed, and, the combined closed circuit. Depending on the presence of the first classifier, the second, or both as well as their corresponding loops (streams), the combined circuit (e) can reduce to; an open (d), a normal closed (b), an open circuit with scalped feed (c) or a reverse closed circuit (a). In the case of an open circuit, the mill is operated without being directly influenced by a classifier. The normal closed circuit does not have the first classifier and therefore the make-up feed is the actual feed stream. Conversely, the reverse closed circuit keeps only the first classifier. The open circuited with scalped feed has only the first classifier but does not have the second one. The overflow stream from the classifier is mixed with the mill product to form the final product for the downstream process."

Jan 1, 2016

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By Peter Van-De-Velde

"The results of applying Japanese pumping technology to North American reclamation projects will be discussed.IntroductionEconomic high-density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.In North America where space has rarely been a facto r, industry has generally relied upon the traditional dumping of material into various waste ponds, etc . In Japan, where confined geographies and stringent environmental regulations are enforced, alternative solutions for disposal or reprocessing of waste material had to be found.High-density mineral reclamation system designed by theoretical formulas is almost impossible because solids composition, i.e. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted dredging of material to relatively dilute slurries whereas it is usually preferred to reduce water usage with its associated power and reclamation costs to a minimum and reclaim as high a concentration as possible.At Toyo Pumps North America we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions."

Jan 1, 1985

By L. C. Hsu, H. F. Jr. Bonham, M. O. Desilets, P. J. Lechler, J. G. Price, L. J. Garside

Abstract-Geochemical background levels have been established for unmineralized sedimentary rocks that are elsewhere the hosts of Carlin-type gold deposits in the Getchell Trend. The Paleozoic rocks in the Winnemucca Quadrangle consist predominantly of the lower Paleozoic siliceous and clastic sequences that were carried eastward along the Roberts Mountains thrust during the Late Devonian and Early Mississippian Antler Orogeny and the late Paleozoic Havallah and Pumpernickel sequences brought along the Golconda thrust eastward during early Mesozoic Sonoma Orogeny. Over 260 rock samples were collected from the Paleozoic sequences. Major and trace elements were determined by instrumental methods best suited for the specific elements. The general geochemical features of the Paleozoic sedimentary rocks are discussed in detail with reference to the data of average abundances of elements in sedimentary rocks. The background and threshold values of certain trace elements in sandstone, shale, and carbonate rock of one formation, as well as back- ground levels for the entire sequence were obtained. The characteristic geochemical features of the Paleozoic rocks in this area include: consistently high Ba and low Au contents (1.1 ppb, 1.5 ppb, 1.1 ppb Au for average sandstone, shale and carbonate, respectively); generally low contents of those elements which may be of environmental concern such as As, Cd, Hg and Pb. Plots of major and trace elements suggest that the majority of the Paleozoic clastic rocks are related to a passive- margin tectonic setting. Samples with gold values higher than threshold are considered to have been affected by hydrothermal alteration related to gold mineralization. Most of these samples generally also have higher values of Sb, Hg, V and/or As. These observations support the use of such elements as pathfinders for gold, although V has not been identified as such before. Ba is not effective for gold exploration in this area due to the generally high background value of Ba, even though it may be an important pathfinder elsewhere.

Jan 1, 1995

By E. Gervais

"In today's marketplace, heavy competition between materials is the norm. This is particularly true f or the base metals, which are being increasingly challenged by new or improved materials in all traditional applications. Current usage of base metals results from a combination of a metal's intrinsic properties, and technology. The future of the base metal industry rests with innovative, high-quality product development, its ability to take advantage of the results of worldwide, massive material R&D investments, and with the dynamism and effectiveness of its market development programs.The ZA casting alloys program is an illustration of the zinc industry’s efforts to protect and expand its market position in the casting field through state-of -the-art technological developments. The market potential f or these advanced engineering alloys is substantial, and their impact on traditional zinc die casting alloy consumption is particuarly important. The ZA alloys, in offering increased performance through zinc castings produced at low cost and by a wide range of moulding processes, have unlocked a multitude of new end-use applications.Following a review of the development of ZA alloys, of their key properties and of their performance characteristics, the numerous challenges that the alloys present to the zinc industry and to the R&D community are discussed.IntroductionZinc is anodic to steel and has a low, uniform rat e of corrosion; it has a low melting point, can be cast with precision , and is readily finished. In addition to its use in protecting steel and in the production of a wide range of castings, zinc is employed : (1) to produce brass, high-strength aluminum alloys and magnesium die casting alloys, (2) in the wrought state for coinage and in building products, particularly as roofing materials , and (3) as an oxide, in the rubber industry, in ceramics, glass, cosmetics, pharmaceutical products and as the starting materials for many chemicals.Zinc die castings are produced with accuracy at high speed, at low cost, are easily finished and have excel1ent mechnical properties . Car fuel economy, changes in automobile styling, competition from other materials, increased sophistication of design and miniaturization have all led to a dramatic change in the volume of zinc consumed for die-casting applications. This has been particularly notable in the United States. Throughout the 19505 and the I960s, casting was the fastest growing major use of zinc; it was firmly established, accounting for 35% of the total zinc consumption(1), By 1983, the volume of zinc being purchased for casting applications had dropped to less than 20% of all zinc consumed in the United States. In the western world(2), consumption for zinc casting application s is currently at about 15%; being nearly equal to the zinc consumed by the brass industry. Coating applications dominate with a consumption of more than 40% of the total market."

Jan 1, 1987

By Irving Wigden

The world is fast becoming information based. Mine companies migrate business infrastructures to be handled electronically. Suppliers move onto the worldwide web. In this ?e-world? successful suppliers will recognize they no longer trade in just equipment, but in knowledge. Companies can no longer just provide products and services, but instead must find ways to harness their knowledge to provide new value for customers. Mine customers will be attracted to suppliers that can help them streamline the process and use Information Technology to optimize operations, increase profit, reduce cost and enhance shareholder value. With the continued move to industry standard communications and software platforms, technology that formerly stood alone can now be integrated with other technologies. This creates more powerful systems that mine operators can use quickly, easily and cost effectively. These unified architectures improve productivity, provide higher asset optimization and allow more informed decision-making. As a leading supplier of process automation solutions for the industry, ABB provides a dynamic range of such control systems. These systems are designed for instrumentation controls, variable speed drives, electrical distribution, electrical equipment and related services for Mine Automation. Enhanced by ABB´s new family of integrated software solutions ? collectively known as Industrial IT ? ABB´s control and Scada systems place you in the best position to optimize your plant, process and enterprise operations. The paper discuss system integration and installation of High-Tec system in an underground mine. ABB has the ambition to be a System Integrator and co-operate with partners in different areas of technology. To day it is a problem to find one Supplier that can be responsible for the complete Automation System. The design of the system is also much depending of the design of the mine and also which caving procedure that is used in the current mine. Much of the work must be done in a feasibility study and during the design phase. If there is careful planning and consideration during these phases is vital in order to avoid costly changes during the commissioning phase The paper will also include a presentation of the benefit of using Automation in an Underground Mine, and how important the integration of the Human Being is to the Automation System. The most profit gained in mining industries are received when the mines can reduce internal and external disturbances in the production flow and speed. Must of the experience and discussed in this paper is from advanced technology, that has been developed in Scandinavian and adopted of LKAB in Kiruna. The author of this paper has been responsible för the Automation projects in the Kiruna Mine during 1994 - 1999. These projects include: Broadband communication of data, audio, compressed video in one data stream. Control System for Haulage -1045m Automation of Load Haulage and Dumping machines (LHD) Control of Production Drilling Riggs from a Central Control Room.

May 1, 2002