Search Documents

By Sanjeeva Latchireddi, Travis Orser

"Today’s high capacity semiautogenous grinding (SAG) mills expend vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. The energy efficiency of these high throughput grinding mills can be attributed to the field of breakage and slurry discharge system. The charge motion and breakage of particles inside the mill depends on the shell lifters design, while the discharge of ground particles is controlled by the grate and pulp lifters. The limitations imposed by poor grate and pulp lifter design become increasingly apparent with increasing size of ag/sag mills and their operation in closed circuit. The design of these mill components has been largely based on trial and error and hence varies considerably between manufacturers. This paper discusses the use of two state of the art design tools - Millsoft™ and FlowMod™. Millsoft™ is an effective tool to design the shell lifters and optimize charge motion, whereas FlowMod™ simulates the slurry discharge system to design grate and pulp lifters. The application of these simulators will be discussed using case studies of full scale mills.INTRODUCTIONMany large mining operations around the world have one or more semi-autogenous (SAG) mills doing bulk of the work in their size reduction operation. The SAG mill is usually followed by a ball mill to finish the size reduction prior to the concentration step. In the past when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the SAG mill operation. As a result mines have shifted their emphasis in optimization from ball mills to SAG mill"

Jan 1, 2005

By F. Channier

The paper provides the most recent information on the construction of the AP60 phase 1 plant of Jonquiere which is due to be commissioned and started up in the first quarter of 2013. HSE management on site by RTA, and cooperation with local equipment manufacturers and contractors of the Saguenay-Lac Saint Jean region are highlighted in this section. The AP60 phase 1 Jonquiere plant aims to demonstrate of the AP60 technology at an industrial scale and allows the further developments of the AP60 cell. The advantages of the AP60 cell technology in terms of productivity, power consumption and environmental footprint are also briefly presented in the paper.

Jan 1, 2011

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By W. M. Armstrong

This paper compares research on development efforts in various countries, consideration being given to gross expenditures, manpower involved, source of funds, sector of performance and type of activity. The Canadian R & D activity is then reviewed, particularly as applied to the industrial sector, the problems of applied research in Canada are discussed and some remedies are suggested.

Jan 1, 1968

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

By Jean-Marc Simard, Vincent Jourdain, Denis W. Roy

"Seven lithologic units, informally characterized, were recognized in the vicinity of the Montauban orebody. The first five lie in stratigraphic order. From structural bottom to structural top these are: (1) grey composite gneiss; (2) dark grey quartz-biotite gneiss; (3) quartz-biotite-garnet gneiss hosting several calcareous, aluminous and magnesian members and gold mineralization; (4) light grey quartz-muscovite-(sericite)-biotite gneiss; and (5) metabasafts. The last two intrude the sequence: (6) amphibolite dykes and (7) pegmatite veins. The orebody lies on the inverted limb of an overturned synform verging to the west with the metabasafts marking the core of the fold. As the foliation is folded, this fold is attributed to deformation ""D2""; deformation ""DI"" being responsible for the formation of the foliation. A late brittle deformation developed shear zones with probable strike-slip motions. The refined stratigraphy and the identification of the structural position of the orebody provide new tools for regional interpretation and prospecting.RESUMESept unités lithologiques ont été définies informeffement à proximité du gisement de Montauban. Les cinq premieres reposent en ordre stratigraphique; ce sont de la base au sommet structural: (1) le ""gneiss mixte gris""; (2) le gneiss gris forcé à quartz biotite; (3) le gneiss a quartz-biotite-grenat comprenant plusieurs membres calcareux, alumineux et magnésiens ainsi que la minéralisation aurifère; (4) le gneiss gris clair à quartz muscovite- Isericitel-biotite; et (5) les métabasaltes. Les deux autres unites sont intrusives dans la sequence: (6) les dykes d ‘amphibolite et (7) les veines de pegmatite. Le gisement se sitlie sur le flanc inverse d'un synforme déverse vers I' ouest dont les métabasaltes occuperaient le cœur. Comm e la foliation est plissée, ce pli est considère appartenir d la deformation ""D2""; la deformat ion ""DI"" etant responsable de la formation de lafoliation. Une deformation cassante tardive se traduit par des zones de cisaillement, d rejet apparemment directionnel. Cette stratigraphie plus précisé et l'indentification de la position structurale du gisement fournissent de nouveaux omits de prospection et d'interprétation regionalé."

Jan 1, 1987

By Michael Cooper, Eric Konigsmann, A. Moerman

"A paste backfill plant and underground piping distribution system was commissioned at the Brunswick Mine in June, 1998. Concentrator tailings, composed mainly of pyrite and lesser amounts of silicate minerals with a P80 of 37um (45 YO-20 pm), are pumped to the backfill plant. The backfill plant uses conventional thickening and disc filtering to dewater the solids, which are then mixed with binder in twin screw mixers. The paste is discharged through a gob hopper and one of three boreholes by gravity. Approximately 65% of the concentrator tailings will be placed underground at full production. The remaining thickened tailings will be pumped to an existing impoundment area. Application of paste technology will completely replace the use of cemented rock fill in the mine by the end of 1998.The design capacity of the paste backfill plant is a total of 360 dmtph of cemented paste through two parallel production lines. The plant is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher ProVox Distributed Control System that is in communication with the property information highway. Video and audio signals from the underground system are carried to the surface plant via a leaky feeder communications/fiber optic system.The underground distribution system consists of a network of 200mm diameter boreholes and piping. There are approximately 3.5km of boreholes and 5.5km of piping in the system. To minimize pressures, the greatest piping length from any borehole is approximately 400m with all piping being open-ended. There are no valves in the entire paste distribution system.Construction of the plant, including installation of piping to and from the plant and preparation of the underground distribution system, was completed in less than one year from the time of management approval for the $M 22.3 project."

Jan 1, 1999

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By G. C. Mackenzie

At the last Annual Meeting of the Institute, Dr. C. V. Corless sketched the potential mineral wealth of Canada so clearly, graphically and with-all so entertainingly that one's imagination was fired with the promise held out to future generations for the tremendous expansion of the mining industry in the Dominion. Posterity will undoubtedly witness the fruit of much of the geographical search and survey that is now carried on by our government mining departments. Year after year the work advances, slowly but surely, new areas are . explored, older areas are surveyed in detail, the information being compiled in maps and reports of incalculable value to the prospector, the engineer and the general public. The immensity of the task of exploring, geologically, the outlying portions of the country, with the ultimate view of making valuable mineral discoveries, may be visualized from a study of Dr. Corless' paper and the subsequent discussion which took place and one becomes impressed with the fact that three-quarters or more of the problem can be included under the word "transportation". For instance Dr. Corless said, "The few geological explorers who have penetrated to these remoter regions . . . . . . have as a rule been compelled to stick closely to canoe routes,"; Dr. Goodwin remarked, "This barren Laurentian granite, which is put down on the maps as covering the greater part of this area, is the best guess the geologist could make from travelling along watercourses Within the next few years . . . . . . the Timiskaming and Northern Ontario railway will undoubtedly be extended to James Bay . . . . . . In order that we may be prepared for the probable influx of prospectors when transportation facilities to tidewater are provided, I think all available information on this district should be gathered together in handy form." All three-Corless, Goodwin and Cole-emphasize the well-known fact that explorers, geologists and prospectors working in new country must stick to the watercourses and that transportation by rail, road or water has always been the all-important deciding factor in facilitating the exploration and development of remote districts. Dr. Corless did, however, suggest other means of transportation in stating, "The aeroplane will be of assistance in future study of some parts of these remote areas."

Jan 1, 1924

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By Richard Frentress, Dave Donelon, Robert Henderson, Mike Warnert

"The Round Mountain gold mine is an open-pit mining operation located 97 kilometres north of Tonopah in Nye County, Nevada. Gold has been produced from the property since 1906.Gold is currently recovered using a combination of four independent processing operations. These include a 10,000 ton per day mill, a 30,000 ton per day, crushed ore heap leach, a 150,000 ton per day, run-of-mine ore heap leach and a small high-grade gravity concentration circuit. In 2002, Round Mountain Gold Corporation produced 755,494 troy ounces of gold at a total direct operating cost of US$2.14 per ton ($193/oz).This paper presents a summary of the Round Mountain operations and discusses some of the processing innovations that have enabled the mine to profitably recover gold from a large low-grade ore body.INTRODUCTIONRound Mountain Gold Corporation is a 50/50 joint venture between Kinross Gold Corporation and Barrick Gold Corporation. Kinross acquired its ownership interest in the Round Mountain mine upon completion of combination with Echo Bay on January 31, 2003. The joint venture partners continue to support an aggressive exploration program in the vicinity of the mine in order to add reserves and extend the mine life.The Round Mountain mine currently operates a conventional open pit that is approximately 8,200 feet long, 4,900 feet wide and 980 feet deep. Mining is conducted on 34-metre benches by electric shovels and front-end loaders paired with 150, 190 and 240-ton haul trucks. Blasthole samples are collected and assayed and provide the control for ore segregation. Based upon these assays, blasted pit rock is determined to be run-of-mine Dedicated Pad ore, crushed Reusable Pad ore, high-grade ore or waste.Gold is recovered using a combination of four independent processing operations. These include run-of-mine ore heap leaching (Dedicated Pad), crushed ore heap leaching (Reusable Pad), milling and the gravity concentration circuit. Non-mineralised rock is delivered directly to the waste dumps. Low-grade ore is trucked directly to the Dedicated Pad and medium-grade ore is crushed and placed on the Reusable Pad. High-grade ore is handled in one of three ways: 1) leached on the Reusable Pad and offloaded to the mill; 2) sent directly to the gravity plant with tails reporting to the mill; or 3) sent directly to the mill or mill stockpile. The gold particle size distribution of highgrade ore determines the processing method."

Jan 1, 2005

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005

By Andrew G. Patton

The Alimak mining method was introduced at the David Bell mine in 1998 to extract an otherwise uneconomic and inaccessible reserve. The success associated with the extraction of these reserves led to major expansion of the method. To date, results have been extremely positive in terms of grade control, reduced dilution, stope recoveries, productivities and mining costs. It is hoped that through further development of the method at David Bell mine we will continue to see positive results in these areas and be able to increase mineable reserves to include proven resources that do not currently meet the criteria of our current stoping plan.

Oct 1, 2001

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By L. W. T. Weitzel

"This paper reviews the Falconbridge- SMRQ’s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40 km property strike length. As a result of its remote northern location, other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel-based financial spreadsheet to bring the total plan together. The focus of the paper is to show the complexity of modern mine planning and associated economic modelling of mine processes. IntroductionThe Raglan project is located 1660 km directly north of Quebec at the northern tip of the Quebec Peninsula in Nunavik. The main property is 40 km in length stretching from the Donaldson airport area at the eastern edge of the property to East Lake at the western edge. The Deception Bay port is 90 km north of the main complex/mill situated at Katinniq which lies approximately in the middle of the property (Fig. 1). The mine processes 1 000 000 tpy of ore from both open pit and underground sources. The mill is forecasted this year to produce more than 150 000 t of concentrate grading more than 18% nickel. All personnel and critical cargo are transported to the site via a company-leased 737 jet from Rouyn-Noranda where the main administration office is located. The majority of cargo is shipped to the site via Deception Bay from Quebec and on the return trip, nickel concentrate is shipped back. From Quebec, the nickel concentrate is sent by rail to the Falconbridge smelter in Sudbury and on the reverse rail haul, nickel matte from the smelter is sent to Norway via Quebec."

Jan 1, 2003

By M. Churchill, V. R. Degner

"Over the past two decades, declining ore body grades, increased operating costs and increased construction costs have provided an incentive for the development of progressively larger flotation machines. As a consequence, the 60 to 100 cubic foot flotation machine of the l950's and l960's is being rapidly replaced by large volume machines, with a resulting improvement in the flotation machine specific capacity (TPH processed per square foot floor space), specific power (HP per TPH processed) and process control simplicity. The recent development, and satisfactory plant evaluation, of the WEMCO 1000 cubic foot flotation machine provides the means by which further economic and operating advantages may be incorporated in high tonnage mill applications.The systematic development of the large 1000 cubic foot flotation machine, and its subsequent performance evaluation in beneficiating metalliferous ores (copper, zinc and iron) will be reviewed in this paper and recently completed plant results will also be provided."

Jan 1, 1982