Search Documents

By G. Q. Zhou, H. C. Liang, X. D. Zhao

"This study describes the strain behavior in vertical shaft lining (VSL) embedded in thick soil deposits and its application in assessment of concrete deterioration. The observed strain in VSL continuously decreased companied by a sinusoidal fluctuation due to the influences derived from negative skin friction (NSF) and temperature. The increase in strain increment between peak and trough at each year and compressive strain level as the servicing time continued and VSL depth increased implies that the concrete strength was attenuated, and this attenuation was significantly dependent on the existing compressive strain level in VSL. The reliability of the proposed approach was validated by Schmidt Hammer Technique (SHT) – based concrete strength, and is applicable in concrete assessment and then fracturing prediction of VLSs in thick soil deposits.Concrete strength, Field monitoring, Strain behavior, Vertical shaft liningINTRODUCTIONOver 100 VSLs in Southeastern China subjected to an unpredictable fracturing as shown in Figure1, and there are over 1,000 VSLs embedded in thick alluvium su?ering from challenges of damaging and potential fracturing (Cheng, Yang, Zhou, Li, & Hu, 1993; Zhou, Cui, Lv, Huang, & Chen, 1999; Li & Li,2005). Therefore, a reliable assessment of these VSLs is significant to the normal servicing of mine shafts and the recycle of underground space when these mine shafts were closed.The continuous increasing of NSF induced by the drainage of water–saturated deposits well interpreted such extensive fracturing phenomenon, and it is universally regarded as the governing indicator to determine the VSL stabilization (Cheng et al., 1993; Zhou et al., 1999). Based on this recognition, the fracturing prediction and VSL strengthening according to the field monitoring on hydrogeological characteristics, servicing environments, and mechanical behaviors of VSL were carried out (Zhao, Zhou, Zhong, Zhu, & Liang, 2009; Liang et al., 2009; Xie, Lv, & Wu, 2014). As known, the compressive strain level in VSL and the in–situ strength of VSL concrete were the main factors to perform such fracturing prediction. However, the existing studies in literatures were limited to the strain accumulating or releasing behaviors (Zhao, Zhou, Zhao, Kuang, & Hu, 2017), and lack of considering the VSL concrete strength and its attenuation. In this reported study, the in–situ monitoring data on the strain in typical VSLs and the VSL elevations between 2004 and 2014 were initially analyzed. Then, an observed strain behaviors–based approach was developed to quantitatively evaluate the VSL concrete deterioration."

Jan 1, 2019

By X. Xe, B. Myhre, N. Zhou, B. Sandberg, Z. Chen

Effects of microsilica and reactive alumina type on flowability, flow decay and working time of Al2O3-SiC-C castables for blast furnace trough were investigated. The results show that at a targeted self flow values of (80 ± 10)%, water demand markedly decreases with increased microsilica addition. The nature of reactive alumina has a strong influence on flowability of the castables. Higher microsilica content contributes to a longer working time. The flow decays gradually until the working time and then drops abruptly. In addition, microsilica have positive effect on both cold strength and hot strength.

Jan 1, 2004

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By Ken Musgrave

"A program is described that helps managers and supervisors control maintenance more effectively. Work- order generation, preventive maintenance, repair parts inventory, planning and scheduling, reporting, analyzing costs, printing purchase orders and other functions are covered. Flexibility often permits integration with other programs such as payroll, cost accounting and materials management.The Role of MaintenanceMaintenance provides a service to allow the rest of the operation to do its job effectively. Its success should not be measured by maintenance cost alone, but also by its effectiveness in reducing downtime and maximizing production. It can make sense to spend more maintenance dollars if this results in an even greater contribution from increased production.The Cost of MaintenanceIn mining companies, maintenance costs can be as much as half of operating costs. Maintenance has generally not been given the management attention that an expenditure of this magnitude deserves."

Jan 1, 1986

By Xiao Huang, Dongmei Wang, Prakash Patnaik

Further increase in gas turbine engine temperature necessitates continuous development and advancement to thermal barrier coatings. While tremendous effort has been devoted to developing new thermal barrier coating materials and processing methods in order to decrease the thermal conductivity, limited attention has been paid to radiative thermal transport through coatings. It is the purpose of this study to develop a new layered coating structure that can be used to effectively reduce the both radiative thermal transport as well as thermal conductivity, and to demonstrate the mechanism and effectiveness of the proposed multilayered structure. Mathematical modeling based on the multilayer quarterwave stack and simulation results are presented.

Jan 1, 2004

By Bill Charbonneau

Lumen, lm The measurement unit of light emitted by a light source 60W incandescent840 lumens 32W T8 linear fluorescent3200 lumens 54W T5HO linear fluorescent5000 lumens 400W metal halide24,000 lumens

Oct 1, 2010

By E. Rezaei

Glue is an animal protein that is used with other organic agent such as thiourea, in copper electrorefining. The concentration of glue has to be controlled carefully, because the electro-deposition process is often very sensitive to small fluctuation in the operating variable. This additive (glue) prevents rough and nodular copper cathode deposits. The nodular deposits may grow causing short circuits, which results in losses in production. Addition agents are effective in controlling metal growth; they modify the normal nucleation and lattice growth steps and refine the grain structure. In this research glue concentration was determined in an industrial copper electrolysis plant. A non-linear model with high capability was constructed and after optimizing its parameters, the accuracy and precision of the model were evaluated. For determination of glue concentration, electrochemical voltammograms in optimum condition (Differential pulse voltammetry technique, Hpulse=50 my, scan rate=10 mv/s) were plotted. Some information from voltammograms was transferred to the model as inputs and the calibrated model analyzed the information and the glue concentration was determined with high precision and accuracy. In this way there is no need to separate or add agents to remove interferences. This method has been successfully applied at Sarcheshmeh copper complex.

Jan 1, 2007

By Y. T. John Kwong

Abstract - To exploit an ore deposit without unduly impacting the environment is a challenge that can only be met by the concerted efforts of traditionally independent teams working on a mining project. Not only is detailed geology required of geologists to help mine engineers to develop a mine plan that assures generation of the least possible amount of mine waste, but metallurgists also have to select the most environmentally friendly mineral processing schemes, and communicate with environmental engineers with regard to complications that process chemicals may pose on proper mine waste management. Traditional ore deposit models typically emphasize the geological and mineralogical aspects of ore genesis to facilitate exploration for similar deposits. Recent research has shown that potential environmental liabilities such as acid mine drainage and metal leaching can readily be predicted according to deposit types. The choice of mining methods, mineral processing schemes, and decommissioning options are also largely dictated by the composition and setting of an orebody to be mined. Integrating such related information into traditional ore deposit descriptions would lead to the development of comprehensive environmental ore deposit models. The latter would facilitate communication among staff of the varied components of a mine project and aid with the selection of a combination of methods and strategies that would assure minimum environmental risks and impacts, reduce the overall project cost, and enhance sustainable development.

Jan 1, 2003

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

An optimization process is described that can be systematically applied by mine planners to produce life-of-mine schedules aligned with their strategic targets, while maximizing the net present value of the mining operation. The software tool employed uses heuristics and an evolutionary algorithm to generate life-of-mine schedules of production and development activities. Generating such schedules is typically a very difficult task due to the large number of operational constraints that must be respected, and the vast number of alternative schedules; as a result the value of the mining operation can be compromised. With an expansion at Newmont?s Leeville mine in Nevada, the mine planners were given the task of producing feasible life-of-mine schedules with significantly increased production rates. Their initial efforts indicated that it would be a considerable challenge to generate such schedules in a timely manner. By systematically applying the proposed optimization process, the mine planners were able to generate optimized life-of-mine schedules with the desired production rate.

Aug 1, 2013

By Perry L. Christian

"Mana/ta Coal Ltd. 's Costello Mine, located seven kilometres east of Estevan, Saskatchewan, has been operating at the present location since 1960. During the past twenty-three years, annual production of lignite coal has averaged 590 000 tonnes. The coal is used for power generation and for industrial and domestic use. Markets, operating techniques, facilities in place and reclamation are discussed. Introduction The Costello Mine (formerly the Klimax Mine) is located in southeastern Saskatchewan, approximately 210 kilometres southeast of Regina and 5 kilometres from the United States' border, as shown in Figure 1. The present mine, 7 kilometres east of the city of Estevan, has been operating since 1960. The history, however, of the Costello Mine and of the Estevan Coalfield dates from the initial settling of the area in the 1880s. Mining initially consisted of burrowing into the side of the Souris River Valley or other hillsides where the coal seam was exposed. Eventually, slopes were put down in the Estevan/Bienfait area and vigorous underground activity existed. In the late 1920s surface strip mining was introduced. The use of strip mining progressed to the point where it completely replaced underground mining in the 1950s and it is the only method in use today. During the past 23 years annual production has averaged 590 000 tonnes. The lowest production was in 1960 when the mine was starting up at 167 000 tonnes and the highest production was in 1977 when production was 1 509 000 tonnes. The Costello Mine controls approximately 11 400 hectares of mineral rights in the Estevan area. This is made up of 4 900 hectares of freehold coal and 6 500 hectares of leases. The area forms a large, irregular shaped configuration. Most holdings are contiguous and adjacent. The mine also owns some 8 400 hectares of surface rights. The lands under the Costello Mine's surface rights control, which are not being used in the mining operation, are leased to local farmers and ranchers. This ensures that the land is used to its full potential, both before and after mining."

Jan 1, 1985

"Beneficiation of low grade ores is the process of increasing the grade of a mineral through unit operations that remove and separate the waste (or gangue) material from the valuable mineral that can then be used for further processing or direct use. Important factors when deciding upon a beneficiation program are the feed grade, mass yield and the metal recovery. As lower grade ores are being processed beneficiation is a critical process. How predictive is laboratory test work for “as built” operating projects? Beneficiation includes all or some of the available unit operations to produce a beneficiation flow sheet i.e. associated unit operations including but not limited to optical sorting, radiometric sorting, crushing and screening, coarse cobbing, jigging, dense media separation (DMS), spirals, magnetic separation, flotation, thickening, filtering and drying. Reference to specific projects and the approach developed in formulating a beneficiation flow sheet and a comparison of difficult and simple beneficiation flow sheets are cited. INTRODUCTIONReserves of high-grade iron ores are reducing all over the world, at an alarming rate, over the years as a result of the rapid increase in demand for steel particularly from Japan and then China. The recovery of mineral value from the low-grade ores using present technology is more expensive than DSO ores due to high energy and capital costs. Beneficiation is defined as a variety of processes whereby extracted ore from mining is reduced to particles that can be separated into mineral and waste.Various physical properties of an ore can be exploited to separate a low grade fraction including variation in hardness, density, reflectance, conductivity and magnetism.""Beneficiation"" of iron ores includes concentration, generally by physical removal of unwanted gangue. Also considered beneficiation is the regulation of product size, or other steps such as agglomeration to improve its chemical or physical characteristics prior to smelting."

Jan 1, 2012

By K. Fujita, T. Kikuchi, Y. Sakamoto

Ceramic fibers were classified as a category 2 carcinogen by The European U legislation. Therefore we developed non-fibrous insulating castable which utilizes n porous aggregate, which is composed of Calciumhexaluminate. Although at beginning we applied alumina cement as binder for non-fibrous insulating castable, kind of formulation had a poor resistance to spalling. We developed non-fibrous insulating castable without alumina cement. This solved a problem which pre\ formulation had a poor resistance of spalling. We applied a new non-fibrous insub castable for reheat furnace in steelworks, then we could achieve good result which condition equivalent to ceramic fiber insulating castable.

Jan 1, 2004

By Michael R. McPhie

Topics of Discussion 1. The Global Mining Initiative (GMI) and MMSD North America (Brief) 2. Task 2 of MMSD North America ? A Test for Sustainability 3. The Seven Questions and their Application 4. Key Recommendations and Next Steps GMI = Global Mining Initiative Significant international collaborative effort supported by more than 30 of the world?s largest mining/minerals firms which sought to involve all communities of interest. Three major streams of activities: 1. Mining, Minerals and Sustainable Development Project (MMSD) ? 4 regional Process (North America, Southern Africa, South America, Australia) 2. Creation of ICMM (formerly ICME) 3. Major conference in Toronto in May, 2002

May 1, 2002

By K. Sun, S. A. Argyropoulos

The assimilation and the exothermic behavior of Zn-Zr metallic powder compacts into molten aluminum was studied by measuring simultaneously the temperatures inside at the centerline of the compact, at its surface, and inside the molten aluminum bath, as well as the net downward force acting on the compact. In addition, the exothermic behavior of these compacts was also investigated in an argon protected atmosphere. The temperature rise inside the compact increases significantly with the mass ratio of zirconium in the compact and to a lesser degree with the aluminum bath temperature. Experimental results on the recovery of these compacts in molten aluminum will also be presented.

Jan 1, 2008

By A. Diaz, Minera Los Pelambres, C. G. Salinas, G. Leinenweber, F. Diaz, D. Rojas, R. Bernal, O. Jimenez

"Los Pelambres Mine (MLP) is located in the IV Region of Chile, a semi-arid region where water plays a key role in operations as a scarce resource and is vital for the sustainability of human life, animals and ecosystem. The conventional flow meters installed on pipes at MLP can fail to provide an accurate measurement due to corrosion and/or fouling on the inner wall or presence of elements in the water such as acids, salts and suspended solids. Conventional flow measurement methods require the inner diameter to be known, however it is not always possible to assess its real value due to scaling, fouling, corrosion, etc. Here we present a novel methodology to solve these problems, which consists of the measurement of flow by a method that does not require the internal area of the pipes: the fluorescent tracer dilution method. In addition, the fluid velocity can be determined by the transit time of a radioactive tracer method. With the flow rate and velocity, the equivalent area is determined and thus the equivalent internal pipe diameter as well. This methodology was applied in a recirculation pump station, for mineral processing from the El Mauro tailings dam.This work demonstrated adequate correlation between measurements from fluorescent tracers and velocity measurements from radioactive tracers, both of which lead to the assessment of the internal diameter of pipes with scaling. The results of both methods disagree with the data provided by the flowmeter installed on the line due to its miscalibration. This information is useful in validating and correcting the information provided by online flowmeters of all water and solutions transport processes in filled pipes.INTRODUCTIONPresently, the need to optimize water resources is increasingly ever important, due to various reasons such as water scarcity, community empowerment, an increased use of water for mining processes and environmental considerations. Taking into account those main considerations, Los Pelambres Mine decided to focus on water conservation to avoid losses of this vital element. They decided to demonstrate that all of the systems that used water (flow meters, pipes, pumping stations, lagoons, etc) were in good condition and that no evitable loses of this important resource occurred. A plan was proposed to conduct a “hydraulic assessment” of fluid flux and water speed at different points and courses at the mine, with the purpose of obtaining hard data to support, verify and correct the information provided online from specific instrumentation dedicated to those purposes. The final goal was to manage the water resource basin in a sustainable way, based on cross-checked information. The chosen points are representative of the processes present in the mine, such as recirculating water stations at different operating conditions and surface water courses, where the fresh water capture systems operate."

Jan 1, 2016

By T. Donkin, B. Patterson, M. I. Guthrie, J. T. Ross

"Interest in the use of particle-based ore sorting has increased significantly with recent advances in sorting technologies and higher capacities per unit. Particle-based ore sorting has the potential to provide great value in processing lower grade ores from mines while delivering higher grades to the mill, as well as in upgrading waste rock into ore. Typically the focus is on the amenability of the ore to ore sorting and associated reductions in energy, water, and consumables utilization. However, layout significantly affects the installed cost of a processing plant, and the impacts on layout from fitting an ore sorting circuit into the plant plan need to be carefully considered. This paper examines processing plant layout considerations that play an important role in ore sorting projects, including additional crushing and screening requirements, transport of rejected material back to the waste stockpile (mine fleet requirements), and effects on the processing plant footprint. ¦ KEYWORDS Cold climates, Ore sorting, Plant layout RÉSUMÉ L’intérêt porté à l’utilisation du tri granulométrique du minerai a considérablement augmenté au vu des récents progrès réalisés en matière de technologies de triage et des capacités supérieures par unité. Le tri granulométrique du minerai offre une plus-value intéressante en termes de traitement du minerai à plus faible teneur extrait des mines ; il permet par ailleurs l’acheminement vers le concentrateur de minerai à plus haute teneur et la revalorisation des stériles dans le minerai. On met généralement l’accent sur la susceptibilité du minerai au triage et sur les réductions connexes en termes d’utilisation de l’énergie, de l’eau et de biens consommables. Cependant, l’aménagement physique de l’équipement a une incidence non négligeable sur le coût installé d’une usine de concentration, et les répercussions sur l’aménagement de l’installation d’un circuit de triage du minerai dans l’usine doivent être soigneusement examinées. Cet article étudie les considérations relatives à l’aménagement de l’usine de traitement qui jouent un rôle important dans les projets de triage du minerai, et notamment les exigences supplémentaires en matière de concassage et de criblage, le transport de matériau résiduel jusqu’à la pile de stockage des déchets miniers (nombre de camions requis dans le parc minier) et les effets sur l’empreinte de l’usine de traitement. ¦ MOTS CLÉS aménagement de l’usine, climats froids, triage du mineraiINTRODUCTION Ore sorting has been practised throughout history. An early report by Agricola in 1556 documents how metallic and non-metallic minerals were extracted from rocks by laboriously breaking them with hammers and picks and hand-picking selected material with higher grade (Hoover & Hoover, 1950). The concept has not changed, but sorting technology has evolved significantly over the last 20 years"

Jan 1, 2019

By R. Burnette

Gold has been mined from a variety of deposit types that range in age from Archaean to Recent. The large variability in the geological settings of the gold deposits implies transport and concentration of gold by magnetic, hydrothermal and sedimentary processes. The factors that control the concentration of gold at certain sites and the grade estimation thereof remain major topics of debate. Due to the complex nature of the Witwatersrand Basin a mineralogical study, including mineralogical, petrographic and geochemical investigation was launched on TauTona Mine in order to characterize the various reef facies. The aim of the investigation was to determine if a correlation could be found between macroscopic characteristics of the reef, hanging wall and footwall, and the microscopic nature of the ore (especially gold grade). Petrograpgic and mineralogical results indicate that a correlation exist between gold, detrital and hydrothermal sulphides, uraninite, carbon, detrital heavyminerals and phyllosilicates. No correlation exist between gold and Mg, Fe or S. It appears that clast supported reef is of higher wade than matrix supported, but more work is suggested. No correlation exists between reef thickness and grade. The reef samples had the lowest phyllosilicate content compared to the hanging wall and footwall samples with pyrophyllite the most dominant. All of the correlations diagrams showed significant scatter and suggests a multi- factorial mineralization model. Gold distribution is also controlled by sedimentary features and thus it is not possible to select a single model for the formation and distribution of gold. It is evident that both sedimentary and hydrothermal factors influenced the mineralization and gold distribution on TauTona mine. It is thus essential that all related theories be incorporated in the development of a grade prediction model.

Jan 1, 2011

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984

By Dan Zou, Ji Chen, Deqian Li

"Bayan Obo mixed RE concentrate is the largest RE source in the world. RE elements occur dominantly in bastnaesite and monazite. This paper describes a clean and green technique for processing Bayan Obo mixed rare earth (RE) concentrate. A two-step oxidation method can lead to the effective recovery of REs, thorium (Th), fluorine (F) and phosphorus (P). Ce has a property of valency change, enabling the separation of it from other RE(III) elements. Making use of the interactions of cerium (IV) (Ce(IV)), F and P, a new extraction system was created to separate Ce(IV) effectively from other RE(III) while recovering F, P and Th by complexing F and P following the oxidation of Ce(III) to Ce(IV). The method includes two parts. Firstly, bastnaesite is oxidized by air roasting and sulfuric acid leaching. And then a first leach liquor containing Ce(IV), F and P is obtained. Secondly, monazite was converted into REhydroxide through alkaline attack and then Ce(III) in the RE-hydroxide was oxidized into Ce(IV) by wetair oxidation. After sulfuric acid leaching the oxidized RE-hydroxide, a second leach liquor is obtained. The two parts of leach liquor containing Ce(IV), F and P are then extracted by Cyanex923 to obtain CeO2, CeF3 and CePO4 based on the complex of Ce(IV) with F and P. The raffinate was further extracted by the primary amine N1923, and Th-product was recovered as ThO2. The RE elements recovery yield during the whole process is greater than 92%. The new technique not only provides a new way for Bayan Obo RE ore utilization, but also avoids resource waste and environment pollution.INTRODUCTIONRare Earths (REs) refer to lanthanides, including scandium and yttrium. Owing to the similar structure and property of RE(III), it is difficult to separate them from each other, especially for the adjacent elements. According to the United States Geological Survey, in 2010, the whole world has about 142 million tonnes of rare earth reserves. In that, China ranks the second with 22% following Brazil which ranks first with 32% (Cheng, 2011). There are three main RE ore types in China with about 80% mixed ores in Bayan Obo, 10% bastnaesite ores in SiChuan and ShanDong province and 2.9% ion adsorption ores in Southern China. Bayan Obo mixed RE concentrate consists of bastnaesite and monazite. The concentrate contains CeO2/_REO of 50% and there are 7–8% F, 4-6% P and 0.2–0.3% Th."

Jan 1, 2016