Search Documents

By J. Cueto, M. Torres, J. Fernandez, J. Nuñez, C. Salgado, G. Zarate

Anglo American has used the extractant M 5640 in all the Divisions, which is an aldoxime modified with TXIB formulation, except in Los Bronces, where an aldoxime modified with tridecanol (TDA) formulation is used. It is a well-known fact that the aldoxime degrades while the modifier does not. With time the aldoxime/modifier ratio decreases significantly depending on the operating conditions of each plant. In order to evaluate the effect of this increasing modifier content in the organic of the plant, especially in the organic losses, a complete metallurgical test work program was started at laboratory and pilot plant scale. Results showed that the addition of aldoxime without modifier does not affect the chemical performance of the organic phase, but there is a significant decrease in the viscosity and density of the organic phase. Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at both SX plants, Mantos Blancos and Mantoverde. In these tests, instead of adding the usual formulation of aldoxime modified with TXIB to maintain the organic inventory, CuPRO MEX™ 3406 which is an aldoxime without modifier is going to be added until the original aldoxime/modifier ratio is reached. The plant tests started in April 2013 at Mantos Blancos and in June 2013 at Mantoverde and will last 18 months. The results obtained at the laboratory and pilot plant scale, together with the preliminary plant test results, are discussed in this paper.

Jan 1, 2014

By S. C. Robinson

"IntroductionALTHOUGH most uranium deposits of the Canadian Shield lie along its western and southern margins, those of the Lake Athabasca region extend easterly along the north shore of the lake and beyond to Charlebois lake. The western end of this belt of deposits, in the vicinity of Goldfields, is 80 miles from the Palaeozoic contact, and its eastern end, at Charlebois lake, is 240 miles from the nearest Palaeozoic rocks.Deposits in this belt may be grouped in four districts, which are, from west to east:(1) The Goldfields district, an area approximately 20 miles square, centred on Beaverlodge lake and extending eastward from St. Joseph's point to Moose channel.(2) A small area in the vicinity of Sucker bay, which is about l0 miles east of Fond du Lac.(3) An area including Middle lake to the northwest shore of Black lake at the Nisto mine.(4) A fairly large area extending northward from the eastern end of Black lake, through Charlebois lake to Spreckley lake.HistoryThe region has stimulated interest in mining circles since the reconnaissance survey of J. B. Tyrrell of the Geological Survey of Canada in l893, who reported concentrations of iron along the north shore of lake Athabasca. The deposits were staked and re-staked up to the early 'twenties' but are too lean to form ore."

Jan 1, 1952

By N. Torres, G. Melcher

"An alternative to building new copper smelters, because of either stringent environmental regulations or in order to expand current plant capacity, could be achieved through the retrofitting of old reverberatory furnaces by making use of tonnage oxygen. The CONTOP® technology offers unique advantages over other techniques for this purpose, especially regarding substantial reduction in bath, capital and operating costs. This is possible to achieve since the reverb throughput could be largely increased with no major structural modifications to the furnace.The following options are offered to the smelter operators: dirty concentrates can be treated in an adjacent Contop system, or the cyclones can be mounted on the reverb roof for either dual operation or full Contop operation. ln the tatter case the furnace will be used as a settling chamber and f or slag c1eaning by top blowing with reducing gases.By incorporating Contop technology, the furnace throughput can be increased, higher malle grade, fixation of sulphur from furnace off-gas and substantial savings in energy consumption are possible to attain.IntroductionCopper smelting has been revolutionized during the last quarter century to such an extent that the standard type of plants consisting o f roasters and reverb furnaces seem a thing of the past, or almost. Though the building of new, more energy efficient smelters is a very likely opportunity for a grassroots plant, it would be hardly justifiable to replace an old existing plant unless there are heavy environmental or economic constraints(1,2,3)."

Jan 1, 1984

By S. Fox, Y. Fujita

Increasing demand for rare earth elements (REE) is expected to lead to new development and expansion in industries processing and or recycling REE. For some industrial operators, sending aqueous waste streams to a municipal wastewater treatment plant, or publicly owned treatment works (POTW), may be a cost effective disposal option. However, wastewaters that adversely affect the performance of biological wastewater treatment at the POTW will not be accepted. The objective of our research is to assess the effects of wastewaters that might be generated by new rare earth element (REE) beneficiation or recycling processes on biological wastewater treatment systems. We have been investigating the impact of yttrium and europium on the biological activity of activated sludge collected from an operating municipal wastewater treatment plant. We have also examined the effect of an organic complexant that is commonly used in REE extraction and separations; similar compounds may be a component of newly developed REE recycling processes. Our preliminary results indicate that in the presence of Eu, respiration rates for the activated sludge decrease relative to the no-Eu controls, at Eu concentrations ranging from <10 to 660 µM. Yttrium appears to inhibit respiration as well, although negative impacts have been observed only at the highest Y amendment level tested (660 µM). The organic complexant appears to have a negative impact on activated sludge activity as well, although results are variable. Ultimately the intent of this research is to help REE industries to develop environmentally friendly and economically sustainable beneficiation and recycling processes.

Jan 1, 2016

By D. Laguitton

"Mathematics, process theory, process practice and computer applications are the main disciplines that contribute to developing useful techniques for computer simulation of mineral and coal processing plants. As in any multidisciplinary effort, communication or transfer mechanisms must be developed to facilitate the flow of experience between participants of different backgrounds. These mechanisms include written reports, verbal communications, workshops and transfer of computer programs. The SPOC project at CANMET is devoted to computer simulation and as such has addressed, or will address in the near future, problems inherent to methodology transfer. The first major output of the project was the material balance program, MATBAL2, which has been acquired by over 30 organizations. Program documentation, industrial workshops and summer student programs have been used to effect the transfer. This experience is discussed and the future outlined.IntroductionComputer simulation has become a common tool in many different fields of human activity during the past two decades, as illustrated in Figure 1. The total number of articles abstracted in Chemical Abstracts under the general subject entry of “Simulation"" has been following a pseudo-exponential growth since 1972 and was approaching 5000 in 1980, whereas no such entry was even used prior to 1967. This represents over a dozen papers published daily on the subject and should continue to grow to higher figures. Still, progress toward accepting modelling and simulation in mineral and coal processing has been very slow. It will be shown later that this slow acceptance is a cause rather than a consequence of the limited success of the various attempts made so far to draw unambiguous benefits from simulation applications. The real cause of the difficulties in fully accepting the new methodology lies in the multidisciplinary aspect of modelling and simulation, which does not suit the traditionally conservative approach that prevails in designing and operating large and costly processing plants."

Jan 1, 1982

By W. L. Stuewe

The Dominion Steel and Coal Corporation requires enormous quantities of bricks each year for its Sydney steel plant operations. Clay brick of all types are purchased, while silica brick is made in the Company&apos;s plant at Sydney. A description of this plant was given in a paper presented by H. B. Gillis and F. C. Morrison at the 1938 Annual General Meeting of the Institute. The rock used to make silica brick was for years obtained from a quarry at Leitches Creek, about eighteen miles from Sydney. Due to the gradual deterioration of this deposit, the Corporation was forced to look for other sources of supply. In 1945, the problem was presented to the Nova Scotia Department of Mines and, through the efforts of Dr. A. E. Cameron and Mr. J. P. Messervey, an examination was made of a silica-rock deposit some six miles northwest of Yarmouth, N.S. Preliminary samples proved satisfactory, and arrangements were made with the Department of Mines to ship to the steel plant at Sydney a fifty-ton car load for the purpose of further testing. Brick made from this sample shipment stood up very well in the furnaces. At the same time, two hundred and fifty tons of silica rock from a deposit at Lac Bouchette, Que., were purchased from the Industrial Silica Corporation, and brick made from this rock also was found suitable for our requirements. Comparative transportation costs, however, led to a decision to open the Yarmouth deposit. The silica rock, or quartzite, of this deposit outcrops at Chegoggin point along what is known as the &apos;Pembroke shore&apos;, a northerly trending section of the coast-line at the extreme southwest of the Province, in Yarmouth county. The country here is fairly flat, with elevation averaging about twenty feet above high tide, and is for the most part mantled by a growth of brush and some scrub trees, chiefly small fir. Bed-rock is generally concealed beneath three to four feet of clayey soil, but scattered outcrops of the quartzite indicated that a band of this rock, some 260 feet wide, extended inland in a northeasterly direction from Chegoggin point at least to Utleys lake, a distance of about three miles.

Jan 1, 1947

By R. D. Brown

"AbstractOver the past five years, tax rates in the Canadian mining industry have skyrocketed upward across Canada, as both federal and provincial governments have sought to increase their share of mining revenues.However, the past few years have not only brought high tax rates to the industry, but also a number of important new federal and provincial tax incentives.In large part, these incentives ~ special credits or reduction in tax for carrying out specific exploration, processing or other activities - have helped to moderate the adverse effects of the higher tax rates and have provided inducements for exploration and processing activities which might not otherwise have been undertaken.However, the effectiveness of certain of these incentives can be questioned: our over-all tax structure now consists in large part of punitively high marginal rates with some extraordinarily generous but capricious tax reductions for specific activities and may not be in the best long-term interest of either the industry or the nation.A rational tax structure, with moderate and stable tax rates, together with reasonable incentives confined to activities specifically requiring them, could be a more effective spur to investment than the present tax and incentive jungleIntroductionIN THE YEARS since federal tax reform, the mining industry in Canada has faced a continued escalation in its tax burdens as federal and provincial governments have leapfrogged each other in imposing new and higher taxes on the industry. The result has been that marginal tax rates imposed on mining and processing activities throughout Canada have jumped to hitherto unparalleled levels."

Jan 1, 1977

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By Rashid Bashir

Shaft sinking through solid rock, which contains little or no water, poses little difficulty. However, when loose, water-bearing strata have to be contended with, water control measures, and pumping facilities are needed. Shaft sinking in Athabasca Basin requires sinking through water bearing sandstone which can be highly fractured. Intersection of local zones of extensive fracturing results in the potential for high water inflows with pressures up to 5 Mpa. Grouting is carried out ahead of each shaft sinking interval as water control strategy. In the grouting method, liquid cement is forced into the water-bearing earth under very high pressure. Shaft sinking performance which can be quantified in terms of rate of advance is highly dependent on the days spent at each interval grouting before sinking can advance to the next interval. This paper presents the shaft sinking experience in Athabasca basin and how some of this is translated into Geoscientific Investigations for Future Shafts. A comparison of Geoscientific data collected from future shafts at McArthur River and Millennium Mines is compared to historical data collected from pilot holes, where shafts have already been sunk. The paper concludes with the strategies for better integration of hydrogeological, geotechnical and geophysical data.

Aug 1, 2010

By J. E. Gill

"The Wasa Lake property is a block of about 1,640 acres in Beauchastel township, Quebec. Gold was discovered there first in 1936 in what is now known as the 'Southern area ( Fig. 1). Stripping and trenching were followed by 9,218 feet of diamond drilling in twenty holes. A number of good intersections were obtained, but their interpretation in terms of ore was difficult. A shaft was then sunk to 220 feet vertical depth. Thirteen hundred feet of lateral work and 543 feet of diamond drilling were completed at the 200-foot level before work was discontinued in 1938. Results up to this point had been just fair.Early in 1944, surface diamond drilling was resumed. The first hole cut material of ore grade in a strong shear zone 1,000 feet north of the old workings, and holes to the east and west showed this to be an extensive gold-bearing zone.In August 1945, a main working shaft was started. This has been sunk to 550 feet slope depth. A cross-cut at 390 feet vertical depth was driven to the ore zone and, by drifting and drilling at regular intervals, a length of 725 feet had been tested to December 31st, 1946 ( Figs. 1 and 2). The results check those from surface drilling quite closely.In the main zone, scoping widths from 8 to 40 feet and averaging about 25 feet are indicated. The grade after dilution should be about 0.15 oz. gold a ton and operation will probably start at 1,000 tons a day."

Jan 1, 1954

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

The total current inventory of mature fine tailings is estimated to be nearly 850 million m³. Pressure has come to bear on the industry to accelerate its tailings management practices and prevent this inventory from steadily growing. The present paper describes the treatment, management and reclamation of fluid fine tailings. New technologies being evaluated include: i) Thin layered - fines dominated deposits, ii) Deep - fines dominated deposits, iii) Fines enriched sand deposits, and finally iv) water capped disposal in end pit lakes. A brief overview for each of the methods of treatment and disposal for fluid fine tailings is provided.

Aug 1, 2013

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By Joerg Hammerschmidt, Marcus Runkel, Steffen Haus

Given the limited number of new plant construction, focus is turning to the optimization of existing metallurgical roasting plants. To meet the goals of high process efficiency with limited capital expenditure, plant owners are looking for new strategies, including digitization and expert support. As a supplier for numerous roasting, gas cleaning and sulfuric acid plants, Outotec has intensified its effort in recent years to develop solutions to accommodate increasing customer need. This article presents a short review on how Outotec is applying advanced control tools for the fluidized bed industry. Focus will be given on how to transfer the existing technology (used in selected Zinc roasting plants for over a year now) to copper roasting. Outotec has developed the Pretium Roaster Optimizer, a system based on heat and mass-balanced simulation models. Direct experience with this technology will be shared and will highlight similarities to the Partial and Sulfate Copper roasting processes. Pretium detects equipment and plant bottlenecks and provides consistency in process development. The Pretium program combines 24/7 advanced online digitalization tools, along with expert personal support when required. INTRODUCTION Fluidized bed reactors have been used for commercial-scale zinc and copper roasting since the 1950s. While the principles of roasting remain unchanged, over time, the technology has advanced to improve process control of roasting plants. In the past, environmental and safety standards were the driving forces for improvement of equipment and plant design. Today, the emphasis is on plant efficiency and optimization. Another change has come in process control philosophy. While plant control and operation have traditionally been the responsibility of owner/operators, they have now shifted to include both integrated digital tools and specific know-how from engineering companies. This can be seen from the earliest design stages through commissioning and into production, as evidenced by zinc roasting plants in Mexico, Brazil and Turkey.

Jan 1, 2019

By Osvaldo A. Bascur

Industrial complexes rely on measurements of flow rates, qualities, and concentrations for monitoring and optimizing their operation. Corporations use the data from the various sensors and measurements to make business decisions, which affect the profitability of the operation. However, gross errors, due to a variety of reasons like faulty sensors, bad instrument calibration, or incorrect process models may corrupt the actionable information supplied to operations, quality managers, and maintenance personnel. The solution is to use the sophisticated new tools to model the process, sift through the available data to locate the gross errors, and use statistical data reconciliation to validate the sensors and instruments. In this way the data are unified to give the most accurate plant information for use by the monitoring and decision making processes. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All of these depend on reliable and accurate data. The data unification methods validate the individual measurements by using the concept of balances and statistical techniques where each instrument is no longer independent of the other measurements in the facility. This paper refers to the data unification and analysis methods required for profitable plant operations. Continuous improvement and monitoring of the measurement system at the plant and analysis of the reconciled data provide the best information for the decision-making process. On-line gross error detection and elimination methods are required to ensure efficient evaluation of process performance and process optimization. An open discussion of the new methods for gross error detection and data unification will be presented.

May 1, 2001

"These standards were developed by the CIM for use with the value or worth of a Mineral Property as opposed to “evaluation” where the key objective is an economic assessment or determination of the economic merit of a propertyP1 .0 BACKGROUNDPl.1 There are at present no comprehensive standards for valuation of Mineral Properties in the Canadian mining industry. The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) specifically recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties.Pl.2 On May 5, 1999 at the Calgary Annual General Meeting, CIM Council approved the formation of a Special Committee on Valuation of Mineral Properties (CIMV al) to be co-chaired by Keith Spence (Chairman of the CIM Mineral Economics Society) and Dr. William Roscoe (Roscoe Postle Associates Inc.).Pl.3 The mandate of CIMVal is to recommend Standards and Guidelines for Valuation of Mineral Properties to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges.Pl.4 The members of CIMVal represent of a mix of professional disciplines and experience in the field of Mineral Property valuation:Keith N. Spence (Co-chair), Alliance Pacific Resources Inc., TorontoWilliam E. Roscoe (Co-chair), Roscoe Postle Associates Inc., TorontoMichael J. Bourassa (Secretary), Aird & Berlis LLP, TorontoChristopher R. Lattanzi, Micon International Limited, TorontoRoss D. Lawrence, Watts, Griffis and McOuat Limited, TorontoPaul E. Lunney, Noranda Inc., TorontoCraig A. Roberts, Pacific International Securities, VancouverDavid A. Scott, CIBC World Markets, TorontoIan S. Thompson, Derry, Michener, Booth & Wahl Consultants Ltd., VancouverWilloughby A. Trythall, retired Placer Dome executive and consultant, Vancouver"

Jan 1, 2003

By S. Duvah Pentiah

The transformation of an open pit coal mine to a horizontal-punch underground mine is subject to a number of challenges. These include scheduling the operation of various sizes of trucks over a long period, as well as updating delivery routes and dump site locations as the mine transformation progresses. In this process, rock is excavated from a quarry through earthworks. The bulk earthwork and quarry material delivery were initially drawn from traditional planning and experienced issues in their early phases. As a result, a traffic simulator was developed in order to validate schedules and predict achievable throughput, likely delays or blockages in the long term. The dynamic traffic simulator was also used to provide traffic density and vehicle arrival data at selected intersections in order to identify possible safety and efficiency issues.

Aug 1, 2013

By Jeremy D. Glennon

A number of exciting challenges, opportunities and unanswered questions remain concerning the chemistry, geochemistry, medical, industrial and analytical applications of gold and its compounds.1 Among the challenges presented is the need for extraction methods for gold, at process and indeed analytical scales, that avoid the use of organic solvents or hazardous reagents. Extensive environmental contamination has occurred in the Brazilian Amazon from the mercury-gold amalgamation process. Major problems with the cyanidation process are the relatively slow dissolution kinetics and the health and environmental problems associated with it. With innovation and technical changes, a cleaner way for solubilising and extracting this versatile precious metal can be found. This cleaner future may lie in supercritical fluid science. Interestingly, geochemical studies of gold solubility and speciation in hydrothermal solutions have highlighted the importance of supercritical conditions and sulphur species in the deposition of gold in natural environments. Gold solubility in supercritical brines is far higher than previously supposed while interest in the high content of carbon dioxide in the mineralizing fluids is growing. 2,3 In recent years, also, there has been a tremendous amount of attention paid in analytical chemistry and in industry, to the area of supercritical fluid extraction (SFE) of organic and metallic species. 4 This interest has been fuelled by the introduction of more stringent environmental control and the subsequent need for cleaner solvents and processes to replace established ones. Carbon dioxide is the substance of choice for SFE because of its moderate critical parameters (Tc = 31oC, Pc = 73atm), inertness and availability in pure form. It is an excellent extraction medium for non-polar and moderately polar species, and with careful ligand design, it can be used for analytical and process scale metal extraction from solution and solid phases. In general, the dissolution of a metal in supercritical CO2 (sc-CO2) requires that the charge on the metal ion be neutralised on complexation by the ligand or through a form of ion pairing (analogous to the situation where metal ions are extracted into organic solvents, such as methyl isobutyl ketone or toluene). In this way, then, many chelating agents such as dithiocarbamates and hydroxamic acids have been utilised to extract metal ions such as Cu and Fe into sc- CO2, the process greatly enhanced by the use of fluorinated ligand derivatives. 5-7 In this review paper, we show that supercritical conditions and complexation with sulphur donor atoms, important in the natural deposition of gold, can form the basis of a clean, eco-friendly chemistry for gold extraction. Analytical scale extractions of gold from a variety of matrices can be conveniently used to assess the efficiency of any new proposed ligand.

Oct 1, 2003

By Jas. E. Thomson

"The Kirkland Lake-Larder Lake gold area is in northeastern Ontario and is a continuation of the ore-bearing belt that extends across northwestern Quebec through the Rouyn, Cadillac, Malartic, and Bourlamaque areas. It is the oldest mining camp along this famous mineral belt. Gold discoveries were first made at Larder Lake and Swastika in 1906, but it was not until 1913 that important developments at Kirkland Lake created a real interest in the country. Total gold production of the camp passed the million dollar a year mark in 1920 and increased in amount yearly until the advent of the second World War when there was a falling off due to labour shortage. The Kirkland-Larder camp ranks as the second largest gold producing area ' in Ontario. To the end of 1944, twenty-two mines in the area had produced bullion valued at $515,631,428 and ten mines had distributed dividends amounting to $205,981,116. The average grade of the ore milled in this period has been $15.17 a ton for the mines in the Kirkland Lake area and $6.49 a ton for the mines at Larder Lake.ROCK FORMATIONS OF THE AREAIn a general way the rocks of the country may be divided into the lithological groups indicated on the accompanying geological sketch map. This map has been compiled largely from recently issued geological sheets of the Geological Branch of the Ontario Department of Minest. Owing to the present difficulty of separating the formations of the Larder Lake country into the twofold age divisions of Keewatin and Timiskaming, the usual custom in the past, a lithological grouping of formations has been adopted. The age terms 'Keewatin and 'Timiskaming' are loosely used in this article to express the often used but not necessarily accurate distinction between the main groups of older strata."

Jan 1, 1954

By Nicholas Bonderoff, Amily Xu

The evaluation of battery electric vehicles (BEVs) in underground mines involves comprehensive business case analysis beyond just the capital and operating costs of the equipment itself. BEVs demonstrate benefits from an EHS perspective, reduced mine ventilation costs, lower energy operating costs, reduced overall GHG emissions (dependent on the source of electricity), elimination of DPM, lower equipment maintenance costs, and reduced cooling requirements in deep mines. When including batteries and supporting infrastructure, BEV capital costs are approx. 80% greater than that of diesel equipment. The project economics are highly dependent on the cost of electricity and diesel fuel, and these can vary widely depending on the location of the mining operation. Battery charging and swapping methodologies must be evaluated as there are a variety of approaches that can be employed which vary by manufacturer and type of equipment. Careful consideration of the cycle times, charging methodologies, and location of the battery charging infrastructure is necessary. Specific operating conditions must also be taken into consideration. For example, the time for blast gases to clear will be increased by reducing ventilation flow, and the potential impact on production needs to be evaluated. Similarly, the electrical distribution system needs to be evaluated for peak loading conditions when BEVs are charging. Criteria including maintainability, reliability, commercial availability, and performance need to be evaluated. BEVs have fewer components than diesel equipment and this correlates to lower overall maintenance costs, however, BEVs require maintenance personnel with specific skill sets in order to maintain the equipment. Battery lifecycle costs need to be considered as battery replacement incurs significant capital expense. Some manufacturers offer services to offset these capital costs through usage agreements. Recycling and disposal of batteries at the end of their lifecycles also need to be considered. With the increased selection of BEV equipment that will be available in the next 2-4 years, 100% BEV adoption is also possible. We recommend a holistic approach when evaluating BEVs for underground mines. This will ensure that everything is considered in order to evaluate the full impact of BEV implementation.

Jan 1, 2023