Search Documents

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By M. Maccagni, J. Nielsen

"Engitec developed the EZINEX® Technology some years ago to recover zinc from oxidized secondary sources. This process works at neutral pH and can take into solution any kind of metal, but iron is rejected and remains in the leach residue. Engitec has also developed the FLUOBORATE System, which is able to recover lead and copper from relevant concentrates. Some iron is leached into solution, but it is controlled through a solution purification bleed treatment. In this paper, we present the two above mentioned technologies. They are very different with regards to the chemical environments and the methods used to control the build-up of iron in solution, but both systems are suitable to treat iron bearing feeds.INTRODUCTIONIn the design of hydrometallurgical processes, the most important issues are the water balance, the filtration and the control of impurities. This is particularly important when the process includes an electrowinning unit. Iron has been one of the most problematic elements to remove, especially in acidic environments.Engitec Technologies has developed several hydrometallurgical processes divided in two different electrolyte lines: the Fluoborate Technology for the recovery of lead and copper from primary and secondary sources and the Ammonium Chloride System based on a chloride electrolyte for the recovery of different non-ferrous metals, among which zinc and lead are the most important. In both cases, iron is present in the feed and needs to be eliminated from the solution. It is not a problem for the quality of the metal produced, but when present in solution, it consumes the basic electrolyte reducing its free concentration which is very important both for both the leaching and electrowinning unit operations. Both process systems are very peculiar, the fluoborate case being much more intriguing."

Jan 1, 2016

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

"The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media. Due to the lack of higher precision influence of temperature on thermal conductivity, we took 6 groups of experiments on rock samples (including igneous rock, sedimentary rock and metamorphic rock) under different operating temperatures from 20? to 50? by 7 acquisition points. The general equation of thermal conductivity drives the value of it increasing along with the decreases of the temperature. While in our experiments, it is easy to find a singularity among them for each sample. The experimental investigations we attempted to observe and interpret the alteration mechanism. According to the Heat Capacity Theory in solid state physics, this research gives the explanation about the “singularity” from 3 understanding of specific heat, average free path, and thermal conductivity. Our research divided the condition of the rock thermal conductivity into 3 different types. INTRODUCTION The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media(Huang & Han ,1988; Peierles ,1955). This parameter is necessary for analysis of heat transfer(Vaferi et al, 2014;Hans-Dieter & Rudiger,2003). It’s well known that a general equation for ?(T) was set by Sass et al. (1992) which based on the coupled effect of composition and temperature on the thermal conductivity(Jesse et al, 2013; Mongelli et al,1982).The equation was further successfully verified for other rock (Zumrud et al,2010;Abdulagatova et al,2009;Seipold& Huenges,1998).Thermal conductivity is also related to other physical proper ties of porous rock, such as thermal diffusivity, heat capacity(Brettmann et al,2011;Abuel-Naga et al,2008). It is well known that ETC and other thermo physical properties of rock materials are affected by various factors, such as temperature, pressure, mineralogical composition, porosity, stratification, size and shape of the components, and nature of pore fluid, etc. (Tiedje & Guo, 2014; Touloukian et al,1970).The understanding of heat transport processes still requires the knowledge of thermal properties of rocks."

Jan 1, 2015

By Charle Pelley, Kosta Fytas, Peter Calder

"A computer model has been developed which is capable of evaluating alternative production schedules (long- and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The model involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. IntroductionMining of mineral deposits in such a fashion so that, at depletion the maximum possible profit is realized, has been a very old problem of the mineral industry. In the past, when high-grade ore reserves were readily available and profits were very high, no question of optimum profitability was raised.However, recently the complexity of both open pit and underground mining has been increased tremendously. The additional problems of continuously rising production costs on one hand and of depressed metal prices worldwide on the other, have been demanding optimum profitabiliy from every mining venture .Particularly in the area of open pit mining, the sequence of ore and waste extraction has now become very important since the size of the pits and of the mining equipment has increased enormously. The process of open pit mining involves a continuous change of the open pit surface and there are many feasible plans of extraction which lead to the same final pit shape (ultimate pit limits). Each of these feasible plans generates a production schedule over the entire mine life, which mayor may not be optimal."

Jan 1, 1987

By Rob Stewart

Acknowledgements ? Josef Macek(Manitoba Geological Services) ? Sally Goodman (SRK) ? Inco Geologists ? Rogerio Montiero ? Thompson Mine Geologists Introduction ? Regional Geology ? Thompson Geology ? Stratigraphy ? Sulphide Characteristics ? Conceptual Model ? Structural History ? Belt ? Thompson Mine ? 1D Deposit ? Ore Controlling Structures ? Using Structural Data to Guide Exploration ? Summary

May 1, 2006

By Transfert Environment and Society

Transfert?s added value ? Building bridges between project promoters and communities ? Unique expertise in working toward Social License to Operate through meaningful community engagement ? 25 years of recognized innovation and a systematic approach ? Key mining clients: ? Royal Nickel Corporation ? IAMGOLD - Niobec ? Richmont Mines - Wasamac ? Mine Arnaud ? Managem

Aug 1, 2013

By Louis J. Cabri

"Mineralogical evaluation of ores containing platinum-group elements (PGE) is fraught with difficulties because of the low grades (often 1-3 g/t PGE), dispersal of PGE (usually as finegrained platinum-group minerals [PGM]), as well as occurring in solid solution in some base metal sulphides (BMS) such as pentlandite and pyrrhotite. Mineral processors not only need to know how the PGE are distributed, that is, their mineralogical distribution, but the grain sizes of the PGM, and especially the associated minerals.After obtaining a representative ground sample, common approaches include studying a large number of polished or polished thin sections, concentration of the PGM and sulphides by different gravity methods (e.g., heavy liquids, elutriation, micro-panning) and study of the produced concentrates. Unfortunately, these methods often do not produce concentrations that are sufficiently representative of a particular ore. The newly developed patented technology of hydroseparation (Rudashevsky et al., 2002) is especially effective at making concentrations of PGM over a wide range of concentrations (down to <300 ppb Pt+Pd+Au) and size fractions, including <45µm (down to a few micrometres in size), a size range not possible by other techniques. This water-based environmentally friendly laboratory technique provides a large amount of data from samples, which can range from 5 to 1000g, giving confidence to extrapolation of results to bench-scale and larger test work, especially when combined with quantitative image analysis to determine modal percent of major minerals and mineral liberation data, needed to predict the minimum (K80) and optimum (K40) grinds. INTRODUCTIONThe invention of the electron microprobe in the early 1960’s and scanning electron microscopes (SEM) with energy dispersive spectrometers (EDS) in the 1970’s presented mineralogists with powerful tools permitting them to obtain chemical and surface area data on minute amounts of minerals in situ, in a non-destructive manner. An area of process mineralogy that has very much benefited from this new technology was the characterization and understanding of PGM species, resulting in rapid growth of newly characterized species (Figure 1). Recognition of the first PGM may be ascribed to the Spanish explorer Ulloa in 1748, who described native platinum from South America. The second PGM (laurite, RuS2) was only recognised in 1866 by Wöhler in placer samples from Borneo (now Kalimantan) and the third (sperrylite, PtAs2) by Wells in 1889 from the Sudbury Ni-Cu sulphide deposits. The discovery of the important Pt-Pd deposits in the Bushveld Igneous Complex led to the characterization of the important Pt-Pd sulphides (cooperite, PtS2 in 1928 and braggite, (Pt,Pd)S2 in 1932). By the early 1960’s, only about 20 PGM were recognised, and many later proved to be poorly or incompletely characterized. Thus, the introduction of electron probe microanalysis (EPMA) led to a 50% increase of known PGM, as shown in a 1972 review on PGM (Cabri, 1972). At the time of the next review in 1981 (Cabri, 1981) the number of known PGM had grown to 75 and as of 2002, it had increased to 109 (Cabri, 2002). However, it is the author’s experience that less than about 25 PGM may be considered to be “common”, i.e., found in many different deposit types, as shown in Table 1, but usually only some of these occur in any one particular deposit."

Jan 1, 2004

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

By A. Rajan

"Drawing upon the experiences of a gold extraction plant startup in the Southern Pacific, this paper will describe the importance of the commissioning phases to the project outcomes to achieve early target production despite an overall time compression to attain full plant production. Some of the highlights of the paper include: impact of roles played by the Owner’s construction and operations representatives during project commissioning, the formation of a capable and competent “Mod Squad,” availability of trained operating personnel, control over work priorities and the scope of work needed to bring the plant to safe initial operations. The commissioning team comprised subject matter experts skilled in process technology supported by “generalists” thoroughly conversant in overall plant operations. The merits of a structured team approach to brainstorm and resolve commissioning challenges as opposed to direction from individual subject matter experts is discussed. IntroductionStartup or commissioning is a unique period in the life of a project. Each stage of a project-exploration, feasibility, design, construction, commissioning, initial operations and continuing operations-requires special talents, know-how, and practices. Each stage makes particular demands of the people involved. Initial operations are no exception.Having experienced the 1997 startup phases of oxide and sulfide facilities for a gold extraction plant at a remote island in the Southern Pacific, I can attest to the many challenges and rewards. Commissioning for both facilities was extremely successful and brought the entire project on line well ahead of the targeted completion dates. Using this specific project as an example, this paper will highlight some of the key features of project commissioning. In this paper, the term “pre-commissioning” denotes all activities that lead to mechanical completion; “commissioning” occurs when feed is introduced; and “initial operations” are defined as the duration when operations accepts the system/facility and takes over."

Jan 1, 2000

By Peter Fullagar, Adel Vatandoost, Steve Walters, Toni Kojovic

"Traditional comminution tests are a vital component in every mine plant design. Comminution behavior governs both the cost of equipment and its operating efficiency. Most comminution tests are conducted off site on a limited number of samples, owing to the high costs and long lead times involved. Therefore a strong incentive exists to find alternative means for efficiently characterizing comminution behavior for a truly representative suite of samples. The potential for inferring comminution behavior from drill core is investigated in this paper. Our approach involves development of small scale comminution tests on the one hand, and measurement of a wide range of core attributes on the other. Our focus is the relationship between petrophysical properties and comminution behavior.Petrophysical properties of archival diamond drill core from the Ernest Henry Mine (Queensland, Australia) have been measured using a Geotek multi-sensor petrophysical core logger. We have investigated the relationship between the petrophysical properties and the corresponding small scale A*b and estimated Bond mill work index test results for 2m composites of the core. Core samples were petrophysically classified by means of cluster analysis. Comminution behaviour was then modeled for each cluster via multiple regression. The results suggest that prediction of the comminution behavior on the basis of petrophysics is viable at Ernest Henry.INTRODUCTIONMineral processing is the most important downstream operation for mining engineers and metallurgists since most mined materials are subjected to some type of comminution or beneficiation operation (SME, 1992). Comminution or size reduction is typically the first stage of processing. Size reduction steps (crushing and grinding) in any plant consume large amounts of energy, normally more than 50% of total energy (Weiss, 1985). Therefore, it is desirable to obtain laboratory results to design the size reduction equipment appropriately. One of the main factors that control the selection of hard-rock crushing equipment and the design of a crushing circuit is the mechanical character of the ore(s). Work index, density, abrasivity, compressive strength and clay content are essential parameters for ore characterisation (SME, 1992)."

Jan 1, 2009

By John H. Fowler

"Most of the aggregate used in Nova Scotia is produced from numerous glaciofluvial and ice-contact deposits scattered throughout the province. Production from bedrock sources is increasing, with most of the coarse aggregate used in the Halifax-Dartmouth area coming from quarries operating within the metro area.A recently completed provincial sand and gravel inventory mapping program has identified some ""resource-poor"" areas where comprehensive aggregate evaluation programs are underway. Although some areas of the province are experiencing aggregate supply problems, large volumes are exported to markets as far away as Bermuda.IntroductionThe Nova Scotia Department of Mines and Energy has been involved with aggregate resource studies for several years, although sand, gravel and crushed stone are not designated as minerals under the Mineral Resources Act of Nova Scotia. Our role has been to provide the aggregate industry with resource data as well as provide similar information to governmental agencies involved with municipal planning, water resource studies and environmental protection regulations. Several private consulting firms use the information in many of their site development studies.We became involved with aggregates in a rather roundabout way. Several years ago, an outcry from inhabitants of a small coastal community over the removal of sand and gravel from a local beach moved the provincial Department of Lands and Forests to take action to protect provincial beaches. We were asked by the Department to provide information and to suggest alternative sources here operators extracting sand and gravel from beaches could relocate. This request initiated an aggregate inventory survey in southeastern Cape Breton, which was later extended to cover the entire province. The initial provincial sand z and gravel inventory survey provided a series of 1:50,000 maps showing the distribution of sand and gravel deposits in the province."

Jan 1, 1982

By Gianni Bartolacci, Patrice Nadeau, Szatvanyi. Gerard, Carl Duchesne, Claude Chrétien

"Combustion is used throughout the mineral processing industry to produce steam in boilers, to dry concentrates in rotary dryers, and to apply heat treatments in pyrometallurgical furnaces. Tight combustion control is very important in latter type of furnace since the combustion conditions directly affect final ore quality. However, achieving tight combustion control is not straightforward since most of the flames encountered in industry are turbulent non-premixed flames, they are affected by several unmeasured disturbances and are often produced by burning several types of fuel simultaneously, some of them coming from other parts of the plant. A novel method is proposed in this paper to improve process and product quality control as well as to optimize the combustion conditions based on digital flame color images. Multivariate Image Analysis and Regression is to used extract the flame color characteristics from images to predict the solids discharge temperature of an industrial rotary kiln. It is shown that this method yield extremely good 10 minutes ahead forecast of the temperature and should lead to a substantial reduction in product quality variability as well as in fuel consumption.INTRODUCTIONFuel-fired furnaces are often used in the mineral processing industry for various purposes, such as for the production of steam (utility boiler), in conjunction with rotary dryers to dry mineral concentrates or in pyrometallurgical processes for induration, roasting, and so forth. These furnaces are necessary in the supply chain from the mine to the metals, but their operating costs are constantly rising due to the fluctuations in fuel prices. Moreover, these processes are now targeted by the Kyoto Protocol since they are energy intensive and they produce significant amounts of CO2 and other pollutants such CO, NOx and SO2. To achieve both a reduction in operating costs (i.e. fuel consumption) and in pollutant emissions while maintaining or improving product quality, one needs to have a very good control of the combustion process."

Jan 1, 2005

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

By H. O. Seigel, J. C. Gingerich, E. O. Köstlin

"To satisfy their continuing need to replenish or expand their ore reserves, mining companies are faced with the dilemma of arriving at a proper balance between the dual avenues of discovery through in-house exploration and of acquisition of properties that are relatively proven or are even in production. The returns from exploration activities may be spectacular, but are unpredictable. The allure of an acquisition lies in its promise of quick and risk-reduced addition to reserves. However, it is historically clear that quantum increments in shareholders’ values have arisen primarily through major exploration discoveries, rather than through major late-stage acquisitions. Late-stage acquisitions can prove highly profitable, sometimes based upon the planned use of superior mining or metallurgical technology, but more often occur as the result of unexpected windfalls. At the other extreme, they can become expensive failures through inadequate due diligence, or unforeseeable factors.Citing numerous case histories and industry statistics, it is concluded that a judicious combination of both exploration activity and the acquisition of prospects is the most advantageous strategy for adding new ore reserves. A skilled exploration staff is essential for success, be it through exploration discoveries or through opportunistic acquisitions, preferably at their early stages. In the future, it is anticipated that there will be fewer opportunities for acquisition because of reduced funding for junior exploration companies, leading to increased competition and higher costs for fewer properties, both in the advanced exploration and mining stages."

Jan 1, 2002

By Carol E. Jones

Outline ? Reclamation is a primary mitigation. ? Understand baseline environment and land use. ? Determine reclamation goals. ? Selecting reclamation technology. ? Determine technical risk. Reclamation ? Primary Mitigation ? Through land and water disturbance, mining can have significant local and regional environmental impacts. ? Impacts can also result from associated land use changes. ? Reclamation is a primary tool that the mining industry uses to manage its environmental impacts.

May 1, 2008

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989