Search Documents

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By R. I. Iacobescu, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, P. Knops

In this work, we explore a novel mineral processing approach using carbon dioxide to promote mineral alterations that lead to improved extractability of nickel from olivine ((Mg,Fe)2SiO4). The precept is that by altering the morphology and the mineralogy of the ore via mineral carbonation, the comminution requirements and the acid consumption during hydrometallurgical processing can be reduced. Furthermore, carbonation pre-treatment can lead to mineral liberation and concentration of metals in physically separable phases. In a first processing step, olivine is fully carbonated at high CO2 partial pressures (35 bar) and optimal temperature (200 °C) with the addition of pH buffering agents. This leads to a powdery product containing high carbonate content. The main products of the carbonation reaction include amorphous colloidal silica, chromium-rich metallic particles, and iron-substituted magnesite ((Mg1- x,Fex)CO3). Carbonated olivine was subsequently leached using an array of inorganic and organic acids to test their leaching efficiency. Compared to leaching from untreated olivine, the percentage of nickel extracted from carbonated olivine by acid leaching was significantly increased. It is anticipated that the mineral carbonation pre-treatment approach may also be applicable to other ultrabasic and lateritic ores.

Jan 1, 2014

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By P. Tracy

An advanced real-time monitoring system, called a "Tapblock Diagnostic System" is under development to help furnace operators manage the operation and maintenance of their tapblocks. The life of a water-cooled tap block in a smelting furnace ranges from several months to several years, depending on the operating conditions. Tapblocks are typically replaced at regular maintenance intervals; a strategy based largely on historical records and not on the actual condition of a particular tapblock. The Tapblock Diagnostic System monitors the tapblock throughout its life and accumulates probable wear events to help the operator assess the residual integrity of the tapblock. Benefits of this system include the ability to provide early warnings of tap block wear to provide improved safety and maintenance planning. Using cooling-water flow together with copper and water temperature measurements, the system performs calculations that compare the present tapblock performance with the expected operating envelope using a multivariate statistical method (Principle Component Analysis). The operating envelope is pre-calculated for a wide range of operating conditions using transient thermal modeling (Computational Fluid Dynamics). A state indicator in the form of a green, yellow and red light is used to inform operators of the tapblock performance and health status.

Jan 1, 2007

By X Dai

This paper investigated the loss of cyanide via oxidation in CIP or CIL processes by relating the cyanide oxidation to its major oxidation product, cyanate. The results showed that the oxidation of both free cyanide and copper cyanide complexes are substantially enhanced by the presence of carbon. The rate of cyanide oxidation was found to occur in the order: Cu(CN)32- > CN- > Cu(CN)2-. The cyanide oxidation rate in the presence of copper and carbon increased significantly with increasing dissolved oxygen concentration, typical of CIL vs. CIP conditions. Cyanide oxidation rate of iron, zinc or nickel cyanide complexes was minimal.

Jan 1, 2011

By Shuji Owada

Scrap electrical and electronic appliances, so called "E-waste", are not a present target to be collected and recycled under Japanese regulations. This material, however, contains considerable amounts of base, precious, and rare metals and it is necessary to recover these elements for maintaining stable supply and establishing "the society of environmentally-sound material-cycle". This paper describes recent trends of rare metals recycling in Japan and technological approaches to achieve the above objective. Also a research work to concentrate rare metals from the printed wiring boards by combining brand new comminution and physical separation methods is discussed.

Jan 1, 2011

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By Greg M. Hollyer

The search for minerals in the future will be dominated by deeper exploration and the need to accurately target ?blind? deposits as more and more of the ?easy? near surface targets are exhausted. In this context, key technologies are emerging for deep exploration both in grassroots and minesite exploration, including the Titan 24 Deep Penetrating geophysical technology. Introduced in 2001, this technology has grown rapidly into an accepted approach for exploration in a variety of geologic environments, including brownfield environments where discovering additional reserves would most quickly benefit companies. Titan 24 belongs to a new class of sophisticated Distributed Acquisition Systems (DAS) which record high-volume, high-quality data simultaneously at multiple receiver stations. This data is then processed digitally, modeled using specialized inverse modeling software, and interpreted according to geologic and other parameters. The result is a robust, high-quality, high-volume data sets which provide a basis for improved imaging to depth. In this paper, the Titan 24 distributed technology is discussed. Illustrations of the vast improvement to overall exploration are showcased through results in several case studies. These include examples from two gold deposits, a porphyry deposit and a minesite. These examples show the range of applicability of the technology and the ability to effectively image mineralization, lithology, structure and alteration to depth as an aid to understanding prospective mineral deposits and targeting drills more accurately.

May 1, 2008

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By H. Thalenhorst

For an advanced mineral exploration project that has a ?nugget? issue making the assessment of the deposit grade difficult, a bulk sampling program using a sample tower can provide information that is otherwise not obtainable prior to actual production. This information includes the verification of predicted resource grades for the bulk sample tonnage (and, indirectly, of the methods and parameters used for the grade estimate), confirmation of the physical and grade continuity of the mineralization, and geotechnical data for a future mining operation. The information gathered will improve the input of a feasibility study, particularly with respect to expected mining grades, which are the key economic parameter for most mining projects. The bulk sample rejects can be used for pilotscale metallurgical testwork. Bulk sampling is also useful in cases of potentially biased drill-hole assay results and in the reliable determination of ore grade before shipment of ore from production or development operations to an external beneficiation plant. This paper presents a practical bulk sampling and sample preparation protocol, lists design features for the sample tower, examines the sampling errors that will be encountered, provides information on quality control procedures, and looks at the costs and benefits of such a program, based on the experience of undertaking bulk sampling programs during the period of 1985 to 2008.

May 1, 2010

By L. Jones, S. R. Lawrence, A. R. Holloway

Whilst dense medium separation is best known for its ability to concentrate diamond and coal deposits, the process is now being employed in southern Africa as a pre-concentration step to improve the economics of platinum group metal and nickel ores. DMS plants built for these industries (such as the 1600tph unit at Tati Nickel, Botswana), are spearheading an expansion in this area by reducing mine and process operating costs yet maintaining economic metal recoveries. This paper provides an overview of DMS technology and examines the economic benefits available to North American operators and projects, with recent case studies as reference.

Jan 1, 2009

By C. Campero, C. Nicolau, L. Pagliero

The Chilean Congress has recently promoted desalination as a solution to meet the mining industry’s growing water demand. However, this rapid expansion of desalination infrastructure comes with trade-offs. This includes a significant energy cost for treatment, as well as socio-environmental impacts on indigenous communities, tourism, fisheries, and the marine ecosystem. This paper advances a regional-scale model for analyzing competing trade-offs through a case study in the Antofagasta mining region of Chile. Through geospatial data analysis in ArcGIS, new desalination infrastructure investments supplying water to mines are overlain with features of concern raised by communities during the environmental impact assessment (EIA) process, such as national parks, fisheries and exploitation areas for benthonic resources. The resultant model provides a test-bed for analyzing the cumulative effects associated with desalination expansion and for investigating scenarios to mitigate negative social-environmental impacts. The model simulates alternative scenarios for desalination locations and pipeline routes according to competing constraints (i.e. to minimize cost and energy constraints while also avoiding ecological and social hotspots). The ultimate contribution of the work is a demonstration of how the proactive adoption of a regional-scale infrastructure planning might have led to different desalination investment decisions. INTRODUCTION Chile represents the largest producer of copper globally, and holds approximately a third of the world’s estimated copper reserves. However, access to water represents a major constraint to industry expansion and creates conflicts with competing water users (Aitken et al., 2016; Côte et al., 2010). Recently, the Chilean Congress has promoted desalination as a solution to meeting the industry’s growing water demand, which is likely to lead to significant growth in desalination infrastructure to support large-scale mining projects that extract freshwater over a rate of 150 l/s1. By most recent projections, the Chilean copper mining sector is set to increase seawater use by 230% by 2029 (Faversham House Group Ltd, 2019). By the year 2015, Chile had 11 projects serving the mining industry and there are at least other 12 planned plants (Cochilco, 2015). While the use of seawater allows continued expansion of the sector without depletion of scarce underground aquifers, it is nonetheless accompanied with important socio-environmental drawbacks. One such challenge with desalination is the associated energy costs, expressed, both economic and environmental (e.g., CO2 emissions). This includes the energy required for reverse osmosis treatment facilities, as well as to pump water to inland regions at high elevations around 3.100 m.a.s.l in Chile. (Dixon, 2013; Knops et al., 2013). Additionally, the impacts of desalinated water use on flotation chemistry are generally poorly understood, necessitating the need for further research into the impacts, both positive and negative (Cisternas and Gálvez, 2018; Liu et al., 2011).

Jan 1, 2019

By CIM Mineral Resource

On January 9, 2018, the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Council formed the CIM Mineral Resources and Mineral Reserves Committee (CIM MRMR Committee), which is a combination of the previous Standing Committee on Reserve Definitions and the Best Practices Committee. As part of its mandate, the CIM MRMR Committee updates guidelines for use by Industry, which include the Uranium Practice Guidelines. The 2024 CIM Uranium Leading Practice Guidelines were adopted by CIM Council on November 22, 2024, and supersedes the 2003 version. The main principles and guidelines relating to preparation of Mineral Resource and Mineral Reserve (MRMR) estimates are provided in the CIM Estimation of Mineral Resources and Mineral Reserves Best Practices Guidelines (MRMR BP Guidelines, as updated from time to time). The MRMR BP Guidelines provide information pertaining to metalliferous and other deposits and many sections are readily applicable to the preparation of MRMR estimates for uranium deposits. However, additional guidance is appropriate for uranium deposits due to the radioactive nature of uranium, and its amenability, in some cases, to in situ recovery (ISR) mining methods.

Nov 1, 2024

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

By Lanny Pasternak

"This article is directed at plant production, engineering and maintenance personnel. Seldom does any industrial operation take the time to study the costs involved in the generation of what is probably their most expensive plant utility energy source.IntroductionIn the typical industrial plant in Canada, a 200 hp, 900 cfm, air compressor costs about $60,000* per year to operate (Fig. 1). In 1989 when BC Hydro embarked on their industrial energy management program Airflow Energy Ltd. were asked to spearhead the “Efficiency Compressed Air” portion of that program with a mandate to perform onsite overview surveys and physical hands-on testing of some 300 selected industrial plants throughout British Columbia for compressor efficiencies and wasteful air leaks (Fig. 2). The program duration lasted until 1995, during which time a tremendous amount of data were amassed relating to equipment types, clients’ operating habits, end-use applications and operating costs.During the past six years, Airflow Energy also performed somewhat similar surveys but on a smaller scale in Alberta, Ontario, the United States and the Republic of China. It was no surprise to find some inherent equipment concerns related to efficiency as well as neglected energy wasteful air leaks, so British Columbia was not alone and the problems appear somewhat universal."

Jan 1, 1996

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By John Clancy, Andrew J. Freyman

"Trends in world coal markets indicate that the next twenty years could be a period of intensive development for British Columbia's coal resource. This paper examines demand projections for metallurgical, thermal and chemical feedstock coals, with particular reference to domestic and Pacific Rim markets. Supply possibilities, from the point of view of British Columbia's competitive position, are explored, with emphasis on the interaction of such factors as capital, labour, port and transportation requirements.The paper concludes with an examination of British Columbia's strategies in light of the foregoing, and comments on the government's role in ensuring that development of the coal resource be attained in a manner consistent with over-all provincial goals and objectives.IntroductionFor the purposes of this paper the Pacific Rim is defined as including, in addition to Canada, the following: Japan, Korea, the People 's Republic of China, Hong Kong, Taiwan, the countries of the Indonesian Archipelago, Australia, New Zealand and the Pacific-bordering countries of South America and Mexico. The United States has been excluded in this definition in order to better illustrate the economic growth potential for British Columbia coal in the Pacific Rim economies.In the past decade, the Pacific Rim economies have grown faster than most other economies in the rest of the world; economic growth rates of 10 per cent were common in the region prior to the 1974 slowdown and the average rate of economic expansion in the mid-1970s has exceeded 6 per cent. Rapid expansion of international trade in the region has been a major stimulus in this process. By 1979, Pacific Rim two-way trade has reached an estimated $550 billion-about 20 per cent of world trade."

Jan 1, 1982

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016