Search Documents

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By R R. Wainwright

Friction-type hoists have been in operation at Geco Mines Limited since Septtember, 1957. At the end of the year 1963, the skip hoist had handled nearly ~ million tons of ore and waste. In March, 1962, with the deepening of the shaft, the hoisting de11th was increased from 1,450 to 2,450 feet. Operating experience with the hoists, hoist and balance ropes, rope treads and other related equipment is presented. The paper is intended to supplement an earlier one -"Heavy-Duty Friction Hoisting at Geco Mines," by W. M. Harvey (C.I.M. Transactions, Volume LXIII, 1960, pp. 193 -197). General G ECO Mine Limited is located at Manitouwadge, Ontario, approximately 160 miles east of Port Arthur and 190 mile northwest of Sault Ste. Marie. The Company was formed to exploit a copper-zinc-silver orebody, with current ore reserve (1963) of approximately 21 million tons. The production plant was designed to mine and treat 1.25 million tons per annum. The production and service hoists are mounted at-the top of a reinforced concrete tower above the shaft.

Jan 1, 1965

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Jarrett. K. M.

Nobody has, as yet, made a perfect machine. Therefore, when a machine is operating and functioning as it is designed to do, there is always some vibration present. This is easily and simply measurable with present-day equipment and any increase in the amount of vibration will indicate a potential failure. When an increase is noted, vibration analysis can pinpoint the cause of the potential failure and remedial action can be taken before an unscheduled shutdown is necessary or a breakdown occurs.

Jan 1, 1972

By K. Yamaguchi

"This Precious metals content copper scrap is treated with a copper smelting process, and copper and precious metals are recovered. The precious metal lost in the slag is increasing with increasing of treated scrap amount. To determine the portion of the precious metals chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. The distribution of precious metals between copper matte and FeOx-SiO2 slag phases is determined at 1300 oC and a fixed partial pressure of SO2 of 0.1 atm for the matte grades from 40 to 70 mass% of copper. The distribution ratios show a tendency to increase when the grade of matte is increased. In addition, the solubility of platinum and rhodium in the FeOx-SiO2-CaO slag under the air and the solubility of platinum in the FeOx-SiO2 slag equilibrated with a pure platinum or the Pt-Cu alloy were determined at 1300oC in the range of oxygen partial pressure from 10-9 to 10-7. The solubility of platinum and rhodium in the slag tends to increase with increasing content of copper in the slag and oxygen partial pressure. INTRODUCTIONThe stringency of the supply and demand of platinum group metal (PGM) intensifies by localization for resources and increase of the demand for PGM, furthermore, smelting and the recycling of PGM in the nonferrous smelting process take an important role. Scrap containing a precious metal for the purpose of collection of PGM is treated by copper smelting recently. With increase of the treatment amounts, loss of PGM in slags is the serious problem.In considering of PGM loss in slags, knowledge of the distribution behavior for PGM between slag and matte phases or slag and copper phases and the PGM solubility in slags is important. The distribution ratios of silver and gold between the FeOx-SiO2 slag and the Fe-Cu matte were reported by Roghani (Roghani et al., 2000), Shinha (Shinha et al., 1985) and Takeda (Takeda et al., 1993) However, there is no data for the PGM distribution ratio. On the other hand, the PGM solubility in slags was reported by Sano (Sano et al., 1997) However, there is very few report for the solubility of PGM in the nonferrous smelting slags."

Jan 1, 2012

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By A. Supomo, H. Resendiz, C. Burbidge

"Freeport-McMoRan Inc. (FMI) commissioned the expansion of the Morenci Metcalf concentrator in 2014. The concentrator included many design and equipment innovations, including the first-of-its-kind Metso Hydraulic Roll Crusher (HRC), variable speed ball mills and variable speed crushers. In addition to the innovative design, FMI commissioned the Metso APC team to design a realistic process simulator and the plant APC. The process simulator was utilized to train operators before commissioning, which led to a smoother plant start up. The plant APC utilized the concept of dynamic constraint control, which controls the feed to the primary ball mills by “pulling” the tons from crushed rock storage bins, which then automatically are filled by the upstream HRC and secondary crushing circuits. The primary ball-mill control also adjusts the water addition to the cyclone clusters to avoid overload and achieve sufficient grind size. The constraints include in-circuit constraints for feeder capacity, screen-deck capacity, ball mill power, cyclone mass flow, pump capacity and pump motor capacity. The APC system was implemented shortly after the start of commissioning and immediately demonstrated increased throughput and an ability to highlight and quantify process constraints and bottlenecks. The following paper outlines the control strategy, discusses system implementation, results and challenges.INTRODUCTION The FMI Metcalf Concentrator is located in Morenci Arizona on the site of the old original Concentrator. The new Metcalf concentrator started operation in May of 2014. This plant was designed for an average of 63,500 tpd (70,000 stpd), increasing the total Morenci concentrator complex production to a nominal 113,400 tpd (125,000 stpd). The process flow diagram is shown below in Figure 1.The process consists of primary crushing feeding a coarse ore stockpile followed by secondary crushing operating in closed circuit with vibrating screen decks. The screen undersize feeds the first of its kind Metso hydraulic roll crusher (HRC) operating in a closed circuit with vibrating screens. The primary crusher is a Metso 60x110 gyratory crusher. Secondary crushers are Metso MP1250 Crushers with variable speed drives. Secondary crusher discharge is recycled to the dry screen feed bin and screened with oversize returning to secondary crushing and undersize feeding the Metso HRC3000. The product from the 3.0 meter X 2.0 meter roll crusher is wet screened with the undersize feeding the grinding circuit, which is comprised of two each 24-foot diameter by 40- foot-long variable speed ball mills running in parallel with each in closed circuit with a cyclone bank of 12 cyclones. The wet screen oversize is recycled to the HRC feed bin."

Jan 1, 2019

By J. Mrozowski, R. Kurowski, A. Chmielarz, Z. Szolomicki

PbSO4 is a commonly encountered component of the materials used in lead recycling (e.g. battery paste) and in by-products of metallurgical processes (e.g. residues from zinc hydrometallurgy, dust from copper smelting). Smelting of battery paste results in SO2 emission and in generation of significant amounts of hazardous ‘white slag’. Those adverse phenomena can be eliminated by removal of sulphur from the paste. Lead-bearing by-product materials are of polymetallic character with usually low Pb content, which makes lead recovery technologically difficult and uneconomic. However it can be successfully achieved by extraction of lead sulphate from solid phase with triethylenetetramine (TETA) water solutions. That compound has capability for selective solvation of a whole lead sulphate molecule. Virtually pure lead carbonate can be precipitated by means of saturation of lead-loaded aqueous TETA solution with carbon dioxide, and complete regeneration of the extractant is achieved by fixing of sulphate ion into gypsum through operation of calcium hydroxide suspension. The paper presents results of the lab and pilot scale studies into process of battery paste desulphurisation and recovery of lead from the residue of zinc calcine leaching.

Jan 1, 2014

Arsenic bearing minerals such as enargite (Cu3AsS4) and tennantite (Cu12As4S13), which may associate with major copper minerals such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and bomite (Cu2FeS4), usually report to the copper concentrate in conventional flotation due to their similar flotation properties. Arsenic in a copper concentrate causes environmental problems and also problems in the subsequent pyrometallurgical process. Voltammetric studies were carried out to investigate the oxidation characteristics of enargite, tennantite, chalcopyrite, chalcocite and bomite. Contact angle measurements and micro-flotation tests were conducted to examine the flotation characteristics of enargite and chalcopyrite under controlled pulp potentials. Selective flotation of enargite from chalcopyrite under varied pulp potentials was conducted to investigate the feasibility of arsenic removal from a copper concentrate. The test results indicate that the non-arsenic bearing copper minerals ( chalcopyrite, chalcocite and bornite) were easier to oxidise than arsenic bearing minerals ( enargite and tennantite) in an alkaline solution. Enargite floated well at a potential as high as +0.45 V vs. SCE while chalcopyrite was completely depressed at a potential higher than +0.43 V vs. SCE. Selective flotation revealed that enargite can be successfully removed from chalcopyrite through controlling the pulp potential at +0.30 ~ +0.50 V vs. SCE.

Jan 1, 2007

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

By T. Xu

"The CTL-500 centrifugal extraction machine, which was independently developed by Baotou Shibo Rare Earth Extraction & Equipment Co., Ltd., is presented in this article. The machine is based on centrifugal extraction principle and has been used in P507-HCl-RECl3 extraction system. Automatic control has been utilized in the system. In this paper, a comparison is made between centrifugal extraction and conventional mixer-settler extraction and satisfactory results are shown. INTRODUCTIONCentrifugal extraction is a fast and efficient liquid-liquid extraction method. The process includes solute transfer and separation of the two liquid phases. In the CTL-500 machine, the organic and aqueous phases individually enter a lower mixing chamber in certain proportions and are mixed and dispersed and solute thereby transferred from one phase to the other. The mixed phases pass into a rotating drum and the two liquid phases are separated under centrifugal force. As it flows upward, the aqueous phase, which has a higher specific gravity, flows away from the rotating drum centre towards the drum wall and the organic phase flows towards the drum center. The two liquid phases enter into collection chambers through independent weir plates and are discharged from the machine.The centrifugal extraction machine has been widely used in liquid-liquid separation, either without solid or with small quantities of solids (Chen, Zhang, Zhuo, Chen & Li, 2008; Duan, Jing, Zhu & Chen, 2007; Duan, Zhou & Zhou, 2006). Examples of the use of the centrifugal contactor include the separation of water from crude oil, treatment of heavy oil and diesel to eliminate water and salt; the extraction of penicillin, garlic oil, malathion, and interferon; the hydrometallurgy recovery of nickel, copper and uranium; extraction of edible oil, spice, refined oil and food color; treatment and recycle of print and dyeing wastes; treatment of hydroxybenzene-contaminated sewage by multistage extraction and separation of water from oil in ship sewage."

Jan 1, 2012

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet 'below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By J. J. Jonas

The categories of interpass time encountered in hot rolling are characterized. These are shown to fall into three broad categories: short (in rod rolling); intermediate (in strip processing); and long (in plate schedules). The effects of interpass time on recrystallization and carbonitride precipitation are described, and particularly on the interaction between these two mechanisms. The interactions, in turn, determine the final microstructure produced as well as the mechanical properties.

Jan 1, 2005

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By A. H. Harvey, M. Delangen, A. D. Fernie

"A large-scale expansion to Pacific Coast Bulk Terminals Ltd. has now been completed and placed in operation. The original plant, built approximately eight years ago, consists of the direct rail-car to ship transfer of bulk commodities. The extension includes additional rail-car unloading, a transfer house system for directing commodities to storage or ship, major storage and reclaim facilities, a second shiploader and a second deep-sea berth. In addition to the facilities for overseas shipments, a wood-chip loader and a barge berth have been installed for domestic shipments of wood chips and, occasionally, for other local commodities. The design considerations imposed by the nature of the products to be handled are covered in this paper."

Jan 1, 1969