Search Documents

By Propser M, Szekely J

Flow maldistribution in the iron blast furnace has been studied analytically by the use of the vectorial form of the Ergun equation and experimentally via packed columns and a cold model of a blast furnace. Experimental results are presented showing the effect on fluid flow patterns of the following types of nonuniformities in a packed bed: the increased voidage at the wall ("wall effect"), the decreased voidage at the interface between layers of materials with different sizes and shapes, and the differences in resistance to flow of bulk regions of a column with different sizes and shapes. The proposed theory is applied to the calculation of fluid flow patterns for these nonuniformities. Velocity profiles, as calculated from these flow patterns, were found to agree reasonably well with experimental measurements obtained via hot wire anemometry techniques for laboratory scale packed columns. Calculated fluid flow patterns are presented for blast furnace burdens which show how flow patterns are affected by (a) coke segregation and (b) the relative differences in resistance to flow between coke and oxide pellet layers. For the cold model study, calculated flow patterns are presented based on photographs of a given burden distribution. The velocity profiles calculated from these flow patterns were found to agree reasonably well with the velocity profiles measured from the cold Model.

Jan 1, 1975

By Eddy B. W, Washusen J. A, Wulff R. T

The State Electricity Commission of Victoria (SECV) has been con- tinuously involved in the extraction of brown coal from open cut mines in Victoria's Latrobe Valley for over 60 years, but have not completed a major mine. Detailed consideration for rehabilitation at this stage has only been able to be given to overburden disposal areas. Increasing interest in rehabilitation in the 1980's led the SECV to review its existing policies and practices and to embark in 1985 on a public consultation process to establish an agreed and accepted policy. This was extended in 1986 to the consultation process for the rehabilitation planning for the Mor- well Open Cut External Overburden Dump. This paper covers the con- sultative process developed and the lessons learned by the participants.

Jan 1, 1989

By Turco E, Pelizza S, Castellani F, Stanganelli V

Excavation are in progress for the building of tunnels of the waterworks in West Campania (Naples). The works afferent to part II envisage tunnelling through a miocenic clay formation over consolidated by two tunnels whose sections are respectively 50 and 10m2. Tunnel blasting is carried out by mechanical means. An excavator is used in the big tunnel, whereas in the small tunnel a roadheader machine is used for a short tract and a mechanized shield is used over a long stretch. The tunnel feature complex problems regarding stability. This is particularly so for the big tunnel whose face appears unstable. For this reason the clay on the face is sistematically bolted by means of 3-metre and 12-metre bolts. This prevent the use of a TBM for tunnel Excavation.

Jan 1, 1987

By E E. Hall, C D. Taylor, D S. Yantek

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

Jan 1, 2005

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The use of concentrated solar flux for high temperature metallurgical applications is a wellresearched area with several reported literatures on solar calcination and metal oxide reduction. This paper presents two such processes with potential to reduce the carbon footprint from ironmaking through using concentrated solar flux. The first process involves solar flux incorporation to the recently developed lime-magnetite pellet (LMP) route of magnetite ore agglomeration. The second process is a hybrid solar-smelting route for iron ore-coal composite pellets that utilises solar flux to provide process heat. Both the concepts of solar agglomeration and solar smelting process were investigated using a solar simulator-hybrid reactor set-up at Swinburne University of Technology. Results from solar agglomeration experiments at 950°C suggested no change in the reaction mechanism of the LMPs under solar irradiation compared to electrical heating. The percentage and morphology of the primary phases (mainly CaFe3O5) appeared similar for both solar and electric heated LMPs. The solar-smelting of magnetite concentrate-lignite coal composite pellets at 1130°C showed a maximum metallisation of 55 per cent after 1.5 hrs of reaction. The solar-smelt process has about 25 to 35 per cent lower CO2 emission compared to the blast furnace ironmaking. Technoeconomic analysis of implementing a CST facility in an existing composite pellet process suggested a payback period of about ten years at a heliostat cost of $A100/m2 and natural gas cost of A$10/GJ. The economics of CST implementation can be further enhanced by decreasing the thermal losses from the heliostat field and reactor.

Nov 8, 2021

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

By Wright S, Rogers L. J, Precious T. H

Brown coal and its char were investigated as substitutes for petroleum coke in the manufacture of anodes for Hall-Heroult cells. The char, which had been densified by several techniques, was made into compacts with various binders and the anodic consumption determined during electrolysis. The results were an improvement on previous work, but the anodes still fell short of acceptability for use in aluminium smelters because of intractable microporosity. Some options for future development have been discounted.

Jan 1, 1986

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

By A Havenga, F, J Hough, R Grobbelaar

After the closure of mines they naturally start to fill up with water. As a result, hydraulic gradients develop between adjacent mines and different hydraulic water pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The geometry of the collieries in the central Witbank Coalfield make intermine flow possible in several areas. Since the Department of Water Affairs and Forestry declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon has been undertaken. The importance of the quantification lies in the DepartmentÆs goal of sustainable water management, and the possible long-term financial implications these flows could have for individual mines. The challenges of determining intermine flow are numerous, and attention is focused on the identification of areas where these flows can take place. Detailed mining plans on a regional scale are required, and detailed coal-seam floor data are combined to provide targets for possible interaction between these mines. The quantification of these flows is problematic due to the uncertainties regarding geometrical configurations and the variation in site-specific hydraulic characteristics of the coal and overlying lithilogical layers. To this end, use has been made of several analytic solutions and numerical flow modelling. Stage curves (volume versus elevation curves) for the opencast and underground workings have been calculated and first-order estimates for intermine flow or decant from these areas have been determined. The numerical modelling methodology entailed a down-scaling approach, starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines and finally looking in detail at the major areas of interaction. By considering different scenarios within the context of these flows, possible management options for intermine flow can be evaluated in terms of volumes and qualities that might emanate in the post-closure phases. Challenges for the future include obtaining site-specific information on the groundwater hydraulics and acceptable ranges for model parameters, and verifying model results over time.

Jan 1, 2003

Kamhalda is located within the Yilgarn Craton of Western Australia, specifically in the Norseman - Wiluna greenstone belt. Numerous nickel sulphide deposits have been mined at Kambalda with I I mines currently operating. For several years, a program of in-mine geophysics has been operating at Kambalda, with downhole electromagnetics (UHEM) one of the key techniques used. Three case studies illustrating the uses of UHEM in mines are presented here. In the first example, the Helmut South deposit was discovered as the result of an extensional exploration program. The first drill hole in the program intersected ore width and grade mineralisation at around 760 in depth. Two subsequent holes intersected subgrade mineralisation. DHEM surveys were completed in each of these three holes, with anomalies recorded indicating that a large conductor was located directly south of the first hole. The next hole intersected this target, for an intersection of 21.6 in at 3.5 per cent Ni. DHEM continued to play a role as the exploration program proceeded, providing drill hole targeting based on anomalous responses recorded in each drill hole. In the second example from Carnilya Hill, old drill holes were surveyed with DHEM in order to search a large section of prospective contact for massive ore pods. An off-hole anomaly was detected and subsequent mining discovered a small but high-grade pod of ore which was extracted for a considerable profit. Carnilya Hill has limited reserves and discoveries such as this, assist in keeping the mine operating. In the third example from Victor, a program of drilling intersected thin ore profiles in an interpreted flanking position. Without massive ore close by, these intersections probably do not constitute economic mineralisation. DHEM surveys of three holes did not detect any conductors. The area is now regarded as sterilised of significant massive ore and exploration efforts and dollars can be focused in other areas. These three examples demonstrate the type of successes that can he achieved through the use of DHEM.

Jan 1, 1997

By T C. Souza Pinto, M Safari, F S. Hoseinian, D Deglon, L Leal Filhoc

In this study, the effect of hydrodynamic parameters on the iron ore reverse was investigated in a mechanical flotation cell. The work carries out using the case study of Iron ore from Vale in Brazil. The influence of hydrodynamic factors such as froth height, impeller speed, superficial gas velocity and solids percentage were evaluated on the quartz flotation. The results showed that the hydrodynamic conditions have a great effect on the flotation performance, especially on the fine and coarse quartz. The size-by-size analysis of the froth products showed that froth height, impeller speed, superficial gas velocity and solids percentage have a significant effect on true flotation quartz particles. The increase in the froth height decreased the recovery of quartz particles. The increase in the impeller speed increases the recovery of quartz particles to an optimum. The increase in the superficial gas velocity improved the flotation of coarse quartz particles. The increase in the solids percentage increases the recovery of quartz particles.

Sep 18, 2023

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

By M Zhu, G Tranell, J You, K Tang, X Ma

The thermal conductivity of slag is critical for the efficiency of high temperature metallurgical processes such as the smelting reduction of ferroalloys, the ladle refining and the continuous casting mold flux in steelmaking. Experimental determination of slag’s thermal conductivity is fraught with challenges, as seen in yielding data for the SiO2-Al2O3-CaO system that are often inconsistent and widely dispersed. In molten slags of this system, thermal transport occurs via phonons within the network structure. To quantitatively describe thermal conductivity based on the microstructure, hightemperature Raman spectroscopy was employed to measure the silicate tetrahedra Qi (i = 0, 1, 2, 3), with Q4 species inferred from mass balance. This study also integrated molecular dynamics simulations to provide a fundamental understanding of the microstructure units distributions. Machine learning algorithms, especially deep neural networks, were applied to establish the relationship between slag composition and the configuration of tetrahedra. The thermal conductivities were then connected with silicate tetrahedra Qi using an Arrhenius-type formalism. This study sets the stage for extending our findings to more complex, multicomponent slags, enhancing their practical application in industrial processes.

Aug 21, 2024

By M Zhu, J Safarian

Understanding the slag composition-structure-property relationship remains challenging due to the amorphous nature of slag melts and the difficulty of high-temperature experimental investigations. Since the CaO-Al2O3-SiO2 slag system is maybe the most important slag system for various hightemperature metallurgical process, the present research employed high-throughput molecular dynamics (MD) simulations on the entire composition region of the CaO-Al2O3-SiO2 slag system to determine physical properties like molar volume, density and diffusivity, structural properties such as distribution of different oxygen types for each simulated slag melt. The obtained slag properties result from the simulations displayed good consistency with experimental data, underscoring the reliability of the MD simulation as a novel tool to predict reasonable slag properties and to study slag behaviour from atomistic insight. The simulated results demonstrate a near-linear relationship between molar volume changes and composition, highlighting the predominant role of oxygen atoms, which is attributed to the significantly larger size of oxygen compared to other cations in the slag melts. This disparity in size leads to oxygen ions occupying most of the space in slags, thereby playing a major role in determining the overall molar volume. The simulation results of slag density revealed a decreasing trend with increased SiO2 content and identified a local minimum at constant SiO2 when Al2O3 content increases, also consistent with established slag density models. Furthermore, the simulated oxygen self-diffusion coefficients reveal a strong composition-structureproperty relationship, where an increase in CaO content enhances slag diffusivity, while a minimum in diffusivity is observed near a CaO/Al2O3 ratio of unity. The diffusivity minimum also corresponding to the local viscosity maxima, indicating effective simulation of charge compensation effects and dynamic characteristics of slag melts. The simulated distribution of oxygen types in slag — bridging oxygen (BOs), non-bridging oxygen (NBOs), free oxygen (FOs) and tricluster oxygen (TOs) — reveals a composition-dependent pattern: BOs peak near CaO/Al2O3 = 1, NBOs and FOs are abundant in CaO-rich areas with NBOs peaking near the Ca3SiO5 composition, FOs in the CaO corner, and TOs predominantly in the Al2O3 corner, highlighting the complex interplay of network formers and modifiers for the charge compensation effects on the slag’s structural properties. The successful application of MD simulations in this study paves the way for a powerful approach to explore the complex relationships in multicomponent slag systems and bridges the gap between mathematics modelling and experimental observations in high-temperature metallurgical processes.

Aug 21, 2024

In line with the recommendations of The AusIMM/AMIC Joint Committee Report in 1981 Isa Mine ore reserves are quoted in proven and probable categories (recoverable ore reserves). Internal reporting considers geological mining and extraction reserves in terms of proven and probable categories. Proven reserves are subdivided into detailed and confirmed ore. External reporting includes a possible ore category (not a reserve). The basis for these divisions is the spatial distribution of sampling data. Proven ore is defined by data 80m apart or less and probable ore by data 80m to 150m apart. Within the proven ore category detailed ore is defined by data 40m apart or less and confirmed ore by data 40m to 80m apart. Kriging is used to provide tonnage and grade information for the currently producing 1100 and 1900 orebodies. Kriged cross sections are initially produced to coincide with existing geological sections and are used for stope design. Stope ore reserves calculations are ideally performed at three discrete design stages, which in order of increasing accuracy are: preliminary design (PD), final design (FD) and ring design (RD). At each of these stages Kriged meshes incorporating the most recent sampling information are produced for reserve calculations. Historically derived mining and extraction factors are applied both to global reserves and individual stope reserves to reflect changes in geological and mining conditions as well as the sequencing of extraction. These factorised reserves are then inserted into the computerised reserves inventory system (RIN). Monitoring of individual stope performance continues into the production stage with input from planning, research, survey and production personnel. This allows actual extraction factors to be derived for comparison with predicted factors, providing some measure of stope performance.

Jan 1, 1987

By Weir D. R, Doyle B. N

The Sherritt Zinc Pressure Leaching Process is based upon the direct pressure leaching of zinc sulphide or lead-zinc bulk sulphide concentrates to produce zinc sulphate in solution and elemental sulphur in the leach residues. The zinc sulphate solution is compatible with conventional purification and electrowinning technology. The pressure leach residues can be treated for the recovery of elemental sulphur, lead and silver. With the conversion of sulphur to the elemental form, zinc pressure leaching allows zinc winning to be independent of sulphuric acid production. Direct pressure leaching of zinc sulphide concentrates was started commercially in October 1980. Continuing research and development studies have defined various pressure leaching configurations for integration with existing roast-leach operations, for grass roots plants, or for plants which are to have the roast-leach section completely replaced. These studies have included the treatment of zinc concentrates from various Australian producers and the development of process flowsheets for potential applications in Australia.

Jan 1, 1989

An improved method of sample recovery for use with rotary percussion drilling has been developed. Cuttings can be recovered continuously from either dry or wet drilling, and the recovery under dry conditions is seldom below 99% of the cuttings brought to the surface by the rig. The system is designed for use with top drive drilling rigs using flush-jointed drill rods. The key feature of the system is a self-aligning mechanical seal around the drill rods. The sealing unit is removably fixed to a collar section of cas ing. the cuttings are recovered in a plastic bag attached to the bottom outlet of a cyclone. A valve at the bottom of the cyclone permits the cuttings representing various depths to I,e recovered separately for examination eind 0(iclysis. [u the Iron Monarch quarry, two percussion holes were drilled to depths if 30 metres and 28 metres using the unproved sample recovery system, and diamond drill holes bored 1 metre from each percussion hole. Samples from each hole were sectionalized over metre intervals and analysed for iron, silica, alumina and loss on

Jan 1, 1976

Different mineral structures can act as mineral reservoirs for the immobilisation of toxic compounds. In the paper different mineral structures will be explained and their potential for incorporation of heavy metals and anions will be shown. The following structures will be explained (P÷llmann, 2007):apatites (incorporation of heavy metals, silicate apatites);ettringites (fixation of oxo-anions);layered double hydroxides (fixation of heavy metals, fixation of anions, fixation of organics, sorption materials); andmanganese oxides. Different possibilities of solid solution and incorporation in crystal structures will be explained and advantages of stable minerals be proved using experiences with real toxic wastes. In the process of thermal treatment the formation of primary mineral reservoirs will be shown. The precursor phases (similar to well known cement minerals) react in contact with water to form secondary mineral reservoirs (cement hydration mineral products). The formation condition of primary and secondary mineral reservoirs and their stabilities and incorporation possibilities will be shown. Examples for incorporation of various elements are given. Application for water clarification will be outlined.

Jan 1, 2008