Search Documents

There are a number of methodologies which can be used for the preparation of environ- mental impact statements. Selection of a method depends upon the type of project and the environmental characteristics of the area where it is to be built. Most methods are satisfactory for assessing impacts on the physical environment but less so for the biological. Major problems may arise in deal ing with sociological issues because value judgements are involved. Several methods of approaching problems of this nature have been tried with some limited success.

Jan 1, 1976

By O Otgonbayar, B Bayarmaa, D Batbyamba, S Amar-Amgalan, K H. Natsagdorj, J Nomin-Erdene, B Boldkhuu, T S. Sainzaya

The Argyle deposit in the Kimberley region of Western Australia was the world’s largest accumulation of natural diamonds. Following its discovery in 1979, the mining of associated alluvial diamonds commenced in 1983, followed by the pipe in late 1985. Over the life of the mine to its closure in November 2020, Argyle produced approximately 900 million carats of diamonds. Argyle diamonds are distinctive in having a predominance of brown colours and rare highly-prized pink diamonds, which are a signature of the deposit. The 3D geological model developed from mining and deep drilling shows that Argyle is a composite pipe formed by the coalescence of several steep-sided diatremes, each with their own feeder zones at depth, that were erupted along a NNE-trending fault. The ~1.2 Ga Argyle pipe is comprised of diamondiferous olivine lamproite volcaniclastic rocks and intruded by sparse olivine lamproite dykes. The volcaniclastic rocks are predominantly comprised of unconsolidated quartz-rich lapilli and coarse ash deposits formed by numerous phreatomagmatic eruptions of olivine lamproite magma through Mesoproterozoic water-rich sands and silts. Post-emplacement deformation has tilted the orebody 30° to the north and regional strike-slip faulting has offset, segmented, and elongated the orebody. Recent significant modifications of the geological model resulted from underground block cave operations, producing several critical lessons learnt. Diamond grade and quality reconciliation issues warranted a geological investigation which resulted in the recognition of new volcaniclastic olivine lamproite domains with a broad range of diamond grades, including some very high-grade units. The new lamproite domains had a significant effect on the block cave mining and resultant recovery of diamonds. The new findings enable a more coherent and detailed geological understanding of the volcanic emplacement and paragenetic sequence of the Argyle AK1 pipe. Structural modelling of the deposit also played a major role in the block cave mining tonnage recoveries and daily operations. The re-examination of the geology of the Argyle pipe and the results of this new information reinforces the need for ongoing robust geological work both in the early stages of mining a deposit and continued during the life of the mine.

Mar 22, 2022

By Giannini L. M

The determination of the "optimum pit limit" of a mine has long been considered as a fundamental problem of mine planning. A number of mathematical techniques have been proposed to solve this problem some of the more elaborate ones posing considerable computational difficulties for their implementation. Barnes and Johnson recently introduced "bounding techniques" to ease the computational effort required for determining the optimum pit. The aim of this paper is to point out and correct some errors in their techniques. A presentation of a general bounding algorithm is given.

Jan 1, 1985

The information requirements of the Australian Stock Exchange Ltd for listing and reporting seek to ensure that the market is fully and correctly informed in a timely manner. This discussion confines itself to the technical reports from mining companies required for prospectuses, information memorandum, quarterly, annual reports and any other announcements to the Exchange. The Exchange requires that technical reports are produced by suitably qualified and experienced personnel and, in the case of a company listing, that these personnel have no interest in the company to be listed. Further, the Exchange has draft prospectuses reviewed by other independent suitably qualified and experienced personnel.

Jan 1, 1987

The Prospero orebody is a part of the Helene mine at Cosmos and was scheduled to begin production in March 2008 after the exhaustion of the Tapinos orebody in the same mine. Treatment of the Tapinos orebody was challenging and it was envisaged that Prospero would have similar properties given that it was also anomalous in deleterious elements and would be of a similar mineral hosting. It was deemed necessary to undertake a metallurgical test work program to identify any potential processing issues, complex mineralogy or significant metallurgical domains. The paper discusses the processes which were employed to undertake the metallurgical test work program and describes the aspects that can be employed by other developers to quickly and effectively assess potential future orebodies. It will demonstrate that the work was successful at determining expected metallurgical behaviour, providing direction for mining operations and highlighting areas for more extensive research.

Jan 1, 2009

By A Coulson, J Hussey

Noranda Inc is a Canadian mining and metallurgical company with its activities managed through businesses in copper and recycling, zinc, aluminum, magnesium and various metals through its interest in Falconbridge Ltd. Noranda operates three base metal mines, three copper smelters, one copper refinery, one zinc refinery, one lead smelter and refinery, three copper recycling and sampling facilities seven aluminum producing facilities and one magnesium production facility in the construction stage. The mining side of Noranda has a strong history of open stope, cut and fill and shrinkage mining. The 1999 Noranda Annual Report lists a 206 million tonne resource located at Porphyry Mountain in GaspT, QuTbec. Mont Porphyre is a large tonnage, low-grade porphyry style Cu-Mo deposit that was discovered in 1994. It is located at a depth between 1.0 and 1.7 km below surface and characterised by a very competent rock mass. The Mont Porphyre resource is located adjacent to the town of Murdochville, close to NorandaÆs Mines GaspT operations. Mines GaspT closed its open pit and underground operations in 1999 after approximately 45 years of mining, but still operates a copper smelter near Murdochville. The low-grade and great depth of the Mont Porphyre resource suggested that mine design could not be based on the conventional Noranda open stoping mining practice. This paper will review NorandaÆs approach to evaluating the Mont Porphyre deposit. The approach included two definition diamond drilling campaigns, a review of current caving practice, an in-house scope study, a geotechnical logging program for diamond drill core and participation in an international study on cave mining. One interesting component of NorandaÆs approach was the scope study that involved a team of multi-disciplinary personnel drawn together for a short period of time. The objective of the scope study was to determine what conditions would be necessary to mine the deposit and to assess the merits of continuing with further exploration work. A review of current worldwide underground bulk mining practices, and in particular an evaluation of the applicability of caving mining methods, were key components of the scope study. The scope study team concluded that derivatives of caving could be applied to the mining of Mont Porphyre, but additional diamond drilling was recommended to further define the deposit and improve the level of geotechnical information. Following the recommendations of the scope study team, a diamond drilling campaign was completed during the summer and fall of 1997. The 1997 drilling campaign had two secondary objectives, in addition to the primary objective of defining the limits of the orebody. The first objective was to improve the level of geotechnical information available for the characterisation of primary block cave fragmentation. The second objective was to improve the delineation of a lower grade intrusive core. A geomechanical investigation was conducted and included particular emphasis on geotechnical data collection and analysis. A review of the actual data collection process, including several trials of different core orientation techniques, will be included in the discussion.

Jan 1, 2000

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

By U JSger

The Westerschelde tunnel will be the first permanent road link between the Dutch regions of South Beveland and South Flanders. Two tunnel tubes, each 6.6 km long, will be driven using the shield tunnelling method. The difficult ground conditions and a water pressure of up to 6.5 bar make great demands on the design. This paper describes the problems and their solutions.

Jan 1, 1999

I In an optical microscope, mild attack by cyanide solutions on various minerals can be observed by means of colour changes as well as etching patterns. However, the mineral may not be identifiable due to the coloured film. In some cases, a transfer algorithm between mechanical stages enables the surface-altered mineral to be identified in the SEM. A more severe attack may not be so informative, as it is not known whether the mineral attacked has been completely dissolved away. The leaching behaviour of some common minerals is described.

Jan 1, 1991

The State of Western Australia has a land area of 2 525 000 km2, and is well endowed with minerals and petroleum products. In 1989 - 90 these products were valued at nearly A$10 500 million.

Jan 1, 1992

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

By Longtin Z, Jin C, Zixin C

This paper proposes a new idea of disintegrating mode (division into simpler sub-problems) for complex problems, and based on -it, a study of the structure and the design of a knowledge base and inference engine for layout design of mineral concentrator expert systems. There is also a study of the formalisation method for describing the layout picture, and the work derived therefore found a formalisation method for expressing the knowledge and experience of layout design. There is also a study of the general characteristics of layout design knowledge.

Jan 1, 1993

Although geophysical methods of prospecting have proved indispensable in the search or oil deposits elsewhere; it is only 'in recent years that they have been used to any significant extent in Australia. The increase in their use has been quite remarkable over the past two or three years, due in Sao small measure to the encouragement given by means of Commonwealth subsidy. There is no doubt that the use of' geophysical methods will coxi-tinue to increase and this increase could be greatly accelerated as and when oil is discovered in commercial quantities,This review of their use A in Australia and the remarks and statistics are confined to work on the mainland. There has been, a substantial amount of geophysical work in Papua, but as operating conditions are so very different to the mainland Papua has been regarded as a separate province.

Jan 1, 1962

By Alvarez A. R, Garcia H. l

A fuzzy expert system, DIME, has been developed, under Matlab v 5.1. to assess the coal and gas outburst risk in underground mining. Expert systems and fuzzy logic are powerful tools to manage information represented by linguistic statements,

Jan 1, 1998

By Seeley D, Buckley N, Goodall J

Improving the performance and reducing the costs associated with export logistics chains is critical to the competitiveness of export coal mines. The fundamental practices associated with the use of export logistics chains made up of mine, trucking, rail and port operations are being challenged by the advent of third party operators on rail systems and the use of the Internet.Whilst individual mines can improve their processes to drive down their mining costs, they face major challenges in their endeavour to improve the performance of export logistics chains and reduce the significant logistics costs of moving coal from the mine to export ships, via the shared infrastructure of rail systems and ports. There is an increasing realisation that global competition is not only between mines but between coal export regions that are defined by their rail system and ports infrastructure.

Jan 1, 1998

Simulation and animation models have developed rapidly over the past decade. Even so, the current state-of-the-art can be viewed only as being in a state of continual development with improvements in both hardware and software constantly being

Jan 1, 1998

This paper discusses the concepts of core risk associated with mining projects and operations and illustrates the types of core geotechnical risks and consequences that may relate to a range of different mining methods, with recommendations on risk management procedures to ensure that the core risks are under constant and ongoing scrutiny and priority management focus. These core geotechnical risks can and should be identified at the initial mining method selection stage, during a feasibility study. They should form part of the auditing of the project and the decision-making regarding the project viability. They should then be built into the ongoing management structure of the project, right through into ongoing operations, with regular audit and review.

Jan 1, 2003

While specific definitions of the main categories of mineral reserves and mineral resources are becoming well established through the efforts of the Australasian Joint Ore Reserves Committee (JORC) and the Combined Reserves International Reporting Standards Committee (CRIRSCO), there has been perhaps less attention paid to the standardisation of language used in the definition and reporting of Mineral Exploration Results and a clear understanding of the transition to Inferred Mineral Resources. This is an area of significant importance to small and medium sized enterprises in the mineral exploration sector as it represents in many cases the only tangible information by which the reader or potential investor can evaluate the future potential of such enterprises. By its very nature information in the Mineral Exploration Results category is incomplete, and frequently complex, and it is open to a broad range of interpretation by readers of various competency levels and disciplines. Many will have a short-term speculative view rather than a long-term perspective, with others out deliberately to misrepresent the information, and as such it can have an enormous impact on investment decisions if the risks associated with this information being reported are not fully understood. Authors of reports on Mineral Exploration Results, who may be Competent Persons or company directors, have to put themselves in the shoes of the reader of the report, second-guessing if you like what the reader will understand by a report, which in many cases will be of a highly technical nature. This raises reporting dilemmas and questions that require to be understood and addressed. Looking at reports on Mineral Exploration Results from the other side, readers have a degree of responsibility as well, particularly if they engage in an advisory or communications role. The tendency of commentators, journalists, analysts, and bulletin board posters to over-exaggerate the significance of a particular exploration result is all too familiar. Questions arise here as well about whether there should be more regulatory supervision and control exercised over those who use this information, all of whom greatly influence investment decisions, and many of whom have no idea there is a Reporting Code, far less an understanding of it. Examples are given and questions raised to illustrate the dilemmas surrounding the reporting of Mineral Exploration Results. In order to retain credibility with markets it is incumbent on companies to be transparent, not to be selective and to report all material information. On the other hand, information has to be taken and read in its proper context in order to avoid fuelling dramatic and unjustified company share price escalation. Timing of course is another factor that can affect the market price of shares, which may be beyond the control of those making the reports. Emotive and imprecise language, however, when reporting Mineral Exploration Results, coupled by speculation, can trigger damaging short runs on shares and destroy credibility where formerly there was long-term promise. The paper will review how Mineral Exploration Results are dealt with in various jurisdictions, and conclude that there has to be a balance between prescription and the tempering of undue optimism on the one hand, and the entrepreneurial spirit, which the industry needs, on the other.

Jan 1, 2002

By Upfold RW, Nguyen VU

The extraction and utilisation of metals and materials is the basis of modern civilisation, and will remain so for many decades, Traditional metals are facing some challenges and research is needed in specific areas, to improve metal extraction processes, to develop processes for newer metals and minerals, and to develop new applications, The shortage of metallurgists now becoming apparent in Australia is a further significant problem that needs urgent attention, and much more publicity is required for the Mineral Industry, as well as for the utilisation Industries,

Jan 1, 1986

Around 35 Mt of industrial clays were produced in 1994 under the broad classifications kaolin (25 Mt), bentonite (8 Mt) and attapulgite/sepiolite (2 Mt). A brief review of world sources and markets is given as background to Australia's small production (0.5 Mt) but developing interest in industrial clays. Clay markets have changed significantly over the past 30 years resulting initially in consolidation and expanded production from traditional high-grade clay sources but also creating opportunities for development of new discoveries. Decline in the use of clay-based refractories has come at a time of strong growth in demand for refined kaolin for the paper industry. Traditional markets for bentonite as oil drilling muds, iron ore pelletising and foundry bond sands are mature and in overall decline. Today, bentonite has a significant share of the growth market in pet litter which a few years ago was dominated by attapulgite/sepiolite clays. Both bentonite and attapulgite/sepiolite have good prospects for increased demand in environmental markets both in containment of hazardous wastes and sorption of toxic substances. In common with all industrial minerals, markets for clay minerals will demand continuous improvement in product quality and consistency. Development of new and improved products will be increasingly the responsibility of the raw material supplier. In order to remain competitive, this will require a substantial commitment to quality assurance and research and development. Increase in market share will come for those producers able to translate developments in their products to cost savings or increased competitiveness for the industries that they Supply.

Jan 1, 1997