Search Documents

By S Raval

The estimation of greenhouse gas emissions from coalmines is increasingly becoming a priority for both operators and regulators. At the same time, involved scientific challenges in the methane measurements is generating significant interest from global research community. Various technology providers are also actively engaged in improving their sensors and platforms to address the measurement challenges and capitalise the market opportunities. This presentation highlights rapidly evolving multifaceted landscape of coalmine greenhouse gas emissions. It covers the advances in sensors for the detections, including ground-based, airborne, and satellite-based systems as well as models for the emission estimations, including attempts to reduce the involved uncertainties.

Sep 1, 2024

By Stevak D, Plesingerova B, Ellias K, Tkacova K

This paper presents information on the processing of minerals by decrepitation that can be an integral part of their mineral dressing. In the case of carbonates, processing by decrepitation is a special operation that has its objective as concentration of the oxide. Selective fragmentation of magnesite brought about by decrepitation uses pseudomorphosis which was observed at thermal decomposition of carbonates. By decrepitation of magnesite high-grade MgO concentrates were obtained with MgO contents above 80 per cent. With the sideritic ores a very important phenomenon was observed consisting in the removal of quartz in the fragmented fine-grained product which favourably affect pelletisation of the fines. The selective concentration of the MgO product brought about by thermal decomposition of dolomite accompanied with decrepitation was negligible.

Jan 1, 1993

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Q Zhou, J Pan, D Q. Zhu, C C. Yang

Oxidised pellets have become an indispensable high-quality charge for blast furnaces (BF) due to their uniform particle size, high iron grade, high mechanical strength, good metallurgical performance, as well as relatively low energy consumption and gaseous pollutant emissions in pellet production. Nevertheless, due to the rapid development of the global steel industry, highquality pellet feeds are becoming more and more scarce. In order to broaden the source of pellet feeds and reduce the production cost of pellets, more and more steel mills are going to use coarse iron ore fines with relatively low iron grade and low impurities for preparation of desirable pellet feeds through a typical wet grinding-settling-filtering process. In this work, the grinding, settling and filtering behaviour of Brazilian and Australian iron ore fines are studied and compared, aiming at finding out the internal relationship between the mineralogical characteristics of different iron ore types and their grinding-settling-filtering performance. The results show that the grindability is heavily dependent on the hardness of iron ores, which is governed by the mineralogical characteristics of the raw materials. Usually the higher the hardness, the more grinding energy is required. Except for Brazilian specularite, Australian hematite-goethite type iron ore fines and Brazilian hematite ore fines exhibit good grindability with a Bond Work Index of about 10–15 kW•h/t. In addition, the settling and filtering performance of ground iron ores are largely affected by the density, mineralogical characteristics of iron ore fines (eg, quantity of clay minerals and goethite and porosity of ore particles), grinding fineness, etc. Generally, iron ore fines with higher density, lower quantity of soft minerals (clay and goethite) and larger particle size give superior settling and filtering performance. For iron ore fines with inferior grinding, settling and filtering performance, applying more energy-efficient grinding techniques, blending with ore types with good settling and filtering performance can reduce grinding energy consumption and improve settling and filtration rates to maximise the productivity of equipment and lower the operational cost

Sep 18, 2023

This research is about human development and socio-economic progress of the main mining areas of Chile in the period 1990 - 2007, and especially about the positive effects that mining activity has on poverty reduction and indicators related to the Millennium Development Goals of the United Nations. The analysis is doubly interesting, if one considers that the economic and social developments in Chile, recognised and prominent among the Latin American economies and developing nations, are more evident in mining areas as Tarapacß and Antofagasta (northern Chile), which concentrated than more 70 per cent of investments and mining assets in the country. Additionally, the study concludes with methodological reflections for the evaluation of socio-economic impact in the mining industry in developing countries.

Jan 1, 2009

Just as geophysics, in the form of 3D seismic and wireline logging, plays a key role in petroleum reservoir management, so too will geophysics play an important role in mining of coal, metals, and minerals in the 21 st century. The commercial and social imperatives driving greater use of geophysics are reduced costs, increased revenues, and enhanced safety. In short, superior utilisation of capital and management of risks. In relatively undeformed sedimentary environments it is possible to adapt petroleum-style 3D reflection seismic to image mines. This has been demonstrated most impressively in the Witwatersrand. Anglo-American, for example, completed a $1 million 3D seismic survey at Western Deeps in order to site a new $300 million shaft with confidence. Likewise, 3D seismic has gained rapid acceptance at Australian coal mines in recent years. Encouraged by these successes, metalliferous mining companies are supporting research in Canada and Australia, as well as South Africa, to adapt 3D seismic for more highly structured, metamorphic terranes. Because the mining industry is far more diverse than the petroleum industry in terms of commodities and geological environments, 3D seismic is not always cost-effective. A plethora of other geophysical techniques can be applied, many of which are employed in mineral exploration. Mine applications of geophysics differ from traditional exploration applications in two main ways: time scales and length scales are shorter, and boreholes are more plentiful. Borehole geophysical techniques therefore play a more significant role, both for logging and imaging. Logging systems detail the variations of in situ physical properties down the borehole at scales measured in centimetres, while geophysical imaging techniques can map features located tens or even hundreds of metres from the sensors. While geologists tend to think of boreholes in terms of chips and core, geophysicists perceive them first and foremost as access paths for instruments. Borehole logging has been employed at iron and coal mines for decades, mainly to accurately define ore boundaries in delineation holes. In base metal mines, Outokumpu implemented logging widely for orebody delineation in percussion holes in the 1980s. The benefit was a direct cost-saving, arising from substitution of core drilling with percussion drilling plus borehole logging. The practice has since spread to other companies. INCO, for example, defines nickel boundaries in blast holes at Sudbury using conductivity logs. The benefits are in the form of reduced dilution and enhanced ore recovery, flowing from a more accurate mine model. Density, natural gamma radiation, magnetic susceptibility, and conductivity are the principal metalliferous mine logging parameters because they can be recorded in both dry and water-filled holes. Sonic velocity is the premier geotechnical logging parameter, given its sensitivity to rock strength, stress, porosity, and degree of fracturing. Sonic is recorded routinely in exploration and geotechnical holes at coal mines. With the advent of slimline dipmeter, full waveform sonic, and optical and acoustic scanner tools, the role of borehole logging in geotechnical evaluations is expanding. Monitoring of strain and micro-seismic activity enhances safety during mine production. While qualitative interpretation of logs is adequate for stratigraphic identification or definition of boundaries, a wealth of quantitative information, eg density, can be derived from properly calibrated, repeatable geophysical logs. Moreover, geophysical logs can sometimes serve as surrogates for geochemical assays, and not only for magnetite and uranium. At OutokumpuÆs Kemi chromite mine, for example, gamma-gamma logging provides the basis for grade control. By reducing reliance on assaying, three benefits can be realised: reduced reliance on core drilling; lower core handling and assaying costs; and shorter turn-around times. Conventional downhole EM and borehole magnetics are used for near-mine exploration, and for ground sterilisation. Inco has enjoyed considerable success with borehole UTEM in the Sudbury Basin, for example, and Geopeko has applied three-component borehole magnetics successfully in the Tennant Creek area. Electrical techniques such as applied potential and magnetometric resistivity (MMR) are also finding application at mines. For higher resolution, borehole seismic, radio imaging, and radar have been invoked, with varying degrees of success, to delineate orebodies and map structures, or to geotechnically characterise the rock mass and identify hazards. Success mapping nickel sulphide shoots with borehole radar has been reported by WMC at Kambalda. There are no universal geophysical panaceas, and each mine imposes different geological, logistical, and economic constraints. Geophysics will not always be cost-effective. However, the greatest single impediment to expanded use of geophysics at mines has been the low level of awareness of geophysics on the part of most mine geologists, engineers, and managers and, equally, the limited understanding of mine geology and engineering exhibited by the majority of geophysicists. This myopia will be remembered as a 20th century affliction! Blue Sky areas for mine geophysics in the next ten years include integration of geophysical data acquisition with drilling, enhanced grade estimation and rock mass characterisation, and the incorporation of geophysical information into mine models using geostatistical techniques. All these advances will be predicated on an expansion of petrophysical knowledge.

Jan 1, 2000

By J Ferreira

To speed up multivariate geostatistical simulation it is common to transform the set of attributes into spatially uncorrelated factors that can be simulated independently. One decorrelation method is the method of minimum/maximum autocorrelation factors (MAF), where a two structure linear model of coregionalisation is assumed. The transformation decorrelates the theoretical model exactly, but the actual data are only approximately decorrelated. The MAF transformation can therefore be seen as a special case of a non-orthogonal approximate diagonaliser of a set of symmetric matrices. A more general approach for approximate joint diagonalisation (AJD) has been developed in the context of blind source separation. For these AJD algorithms no assumptions are made beyond symmetry of the individual matrices and so they can be applied to a family of experimental semivariogram matrices. In their application there are no restrictions on the number of structures in the linear model of coregionalisation (LMC) thus removing one of the conditions placed on the subsequent modelling of the spatial structure of the factors. In this paper the general background for the U-WEDGE AJD method is presented. It is shown that the U-WEDGE method achieves better spatial decorrelation than the MAF method. The factors derived from U-WEDGE are simulated using conditional turning bands simulation and then backtransformed to attribute space.

Sep 26, 2011

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By Booth S. A, Milton D. W

Stratabound/stratiform and remobilised mineralisation have been recognised as the two dominant styles of mineralisation which constitute the Broken Hill ore deposit. Recognition of prospective sites for accumulation of ore depends on understanding the heterogeneity of the ore environment and the distribution of the two styles of mineralisation. The internal stratigraphy of the Broken Hill ore deposit and its enveloping rocks, is described, and a generalised stratigraphic setting of the stratiform mineralisation is outlined. Fhiphasis is placed on the existence of closely-spaced sub-basins as potential sites for ore accumulation close to the Broken Hill ore deposit. Further from the immediate ore environment, recognition of the same diagnostic stratigraphic sequence

Jan 1, 1983

By Tamura S, Maekawa M, Nagai C, Deguchi M

Heavy fuel oil has been injected into blast furnaces in order to reduce the coke rate, to improve productivity and to control the furnace heat condition. However, in the first oil crisis at the end of 1973, it became necessary to develop an injection technique of new fuels into blast furnaces to reduce oil consumption. In Kobe Steel, Ltd., it was thought that the injection of a coal-oil mixture (COM) into blast furnaces could be developed in a shorter time than pulverised coal injection. The development of this technique was under- taken in 1974, and COM was injected through two tuyeres of the No.3 blast furnace at the Kobe works in 1977 and 1978. In addition, in order to study the combust- ibility of COM and the phenomena in the tuyere zone, the development of a gas sampling method was under- taken in 1975. In this paper, the results of the injection tests and gas sampling tests are reported.

Jan 1, 1981

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By J Bean

Iluka Resources Ltd developed the Jacinth-Ambrosia Mine (Jacinth) in the Eucla Basin during 2009 and 2010. In this arid climate the operation relies on hyper-saline groundwater from a palaeochannel for process and potable water supplies. The water is hyper-saline, acidic and mildly reducing, with high ferrous iron concentrations. Ferrolysis commences on exposure of water to oxygen, resulting in increased acidity and the conversion of dissolved ferrous iron to insoluble ferrihydrite. The unstable groundwater forces a careful balance between interventions relating to maintaining pipeline efficiency, corrosion protection and processing aspects. Providing an oxidising environment at the head of the pipeline will result in the precipitation of akaganenite and goethite in the pipeline, which over time reduces pipeline efficiency. However, sending too much ferrous iron forward may reduce processing performance.The processing plant experiences changes in water chemistry in response to the variability of iron concentrations and pH within the pipeline, and the spatial and chemical variability of ore. As the main orebody at Jacinth contains little buffering capacity a source of carbonate in the overburden is carefully used to allow the cost-effective control of process water pH.This paper highlights the importance of understanding the chemistry of saline make-up water, ore, and overburden when designing water treatment facilities and heavy mineral processing facilities.

Oct 5, 2011

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (<1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

The Grootegeluk coal beneficiation plant is situated near Ellisras in the Waterberg coal= field in the Transvaal, RSA. At this plant 15 million tons of coal bearing material per annum are beneficiated by means of two-stage heavy medium bath and cyclone plants. Because of the very low yield of 12 % coking coal product, run= ping costs are of the - utmost importance. For this reason extensive tests were carried out to establish the most effective crushing and bene= ficiation methods and suitable aquipment. At the second heavy medium separation stage, the near-gravity material (+ 0,1. g/cc) amounts to 45 % and daily plant performance ana=lysis is required to ensure acceptable plant efficiency. Beneficiation processes for the -0,5 mm coal originally considered were froth flotation, shaking tables, heavy medium cyclones and water- only cyclones. When the froth flotation route was decided upon, further test work was done to enable selection of the equipment most suitable for the particular requirements.

Jan 1, 1987

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

Wetherstones gold deposit is located just east of the township of Lawrence, in the Otago District of the South Island, New Zealand. The paper will describe aspects of the mining and exploration history of the Wetherstones gold field, current knowledge of the geology of the deposit, and speculate on possible outcomes of exploration in the modern era.   As at the famed Gabriels Gully situated nearby, most of the Wetherstones gold is/was contained in, or recycled into modern drainages from, the Blue Spur Conglomerate (æBSCÆ). The BSC is the basal member of a wedge of auriferous non-marine sediments of latest Cretaceous age which are tilted against the Tuapeka Fault Zone, a structure of regional dimensions. In particular mineralisation of elevated grade (which cannot yet be reliably estimated) appears to be concentrated in an elongate basement depression (ægutterÆ) of width around 100 m, variable thickness to a few metres, and axial length in excess of 500 m. The gutter plunges from the base of alluvial mining (where it has been partly exploited by underground methods) to depths of more than 100 m, beyond which it remains open and untested.   The prospects for a revival of mining at Wetherstones depend upon confirmation of what is here inferred to exist, and the discovery of additional gold. The economic prospects of the project however are enhanced by what is known or indicated of the geographic location, and anticipated geologic, mining and metallurgical characteristics of the mineralisation, and consequent anticipated environmental management issues.   The recognition of gold contained in pyrite in the BSC represents an upside to project economics which has never previously been evaluated. The Wetherstones Basin covers more than five square kilometres in areal extent. There is no modern exploration record of the majority of this area, leaving open the prospect of the discovery of additional gutters, and primary mineralisation in the underlying schist.   Australasia Gold Ltd has embarked on a program to reassess the potential resources of the Wetherstones gold mineralisation, and to evaluate the feasibility of mining.

Jan 1, 2004

By G R. Ballantyne, B Putland, I Lovatt, M Di Trento

The Tropicana Gold Mine, owned by AngloGold Ashanti Australia Ltd (70% owned and managed) and Independence Group NL (30%) is located 330 kilometres east-northeast of Kalgoorlie, Australia, in the newly developed Albany-Fraser Orogen. Following extensive feasibility studies, a high pressure grinding roll (HPGR)-ball milling circuit was selected based on the reduced power requirements and thus reduced operating expenses. The HPGR-ball mill circuit was estimated to require 75% of the energy of a standard semi-autogenous grinding (SAG) mill circuit. Even with an anticipated greater capital cost, the HPGR-ball mill circuit was found to give significantly better financial returns in all cases investigated in the feasibility study. A comparison between the specific energy requirements of the HPGR, crush and SAG based circuits (SABC) from the feasibility work was conducted and the HPGR circuit was found to be considerably more energy efficient. A survey was conducted and the efficiency of the HPGR was similar to both the overall circuit design and the HPGR laboratory results, reflecting the accuracy that is possible for design and operation of HPGR circuits.Between 2015 to 2016, the Tropicana circuit has achieved a 20% increase in throughput from 780 to 930 t/h, and this increase has been maintained in 2017. This improvement can largely be attributed to upgrades to material handling processes, increased HPGR speed and smaller HPGR screen apertures. The result of these changes has been to increase the ball mill capacity by increasing the breakage conducted by the HPGR.CITATION:Ballantyne, G R, Di Trento, M, Lovatt, I and Putland, B, 2017. Recent improvements in the milling circuit at Tropicana mine, in Proceedings MetPlant 2017, pp 73–83 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D Kahler

Modern gold production from the Gympie Goldfield commenced in 1995 with the first production from the Monkland Mine. The primary ore target was the 2.5 m wide Inglewood Fault ore zone, which was initially mined using traditional narrow-vein shrink stoping. This manuallyintensive mining method allowed the mine to re-open with minimal capital cost, however the trade off was low productivity and high operating costs. As the mine has developed, access through 100-year-old, timber-lined, small shafts, and the high cost of delineating reserves, has restricted modernisation of the operations. In early-2000 a stockwork lode was discovered adjacent to the existing workings with an economic width of 40 m. In order to maximise the benefit of such an orebody, mining needed to be approached in a new way. This paper summarises the many changes implemented at the Monkland Mine, including the necessary cultural change, implementing long-hole stoping, de-bottlenecking and the application of mechanisation. The result has been a significant improvement in safety performance, higher productivity and a more secure future for all those involved in the project.

Jan 1, 2002

By G Harbort

The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to convert spatial geological data into metallurgical information to drive production and mine planning, blast design, blending strategies and plant set-up. Increasingly the process designer is required to interface with geological and mining staff to propose the best investment strategy for a project’s benefit.The geometallurgical model development for the Zafranal copper-gold project commenced in March, 2010, several months after the start of a major drilling campaign by AQM Copper Inc. The initial evaluation stage required review of historical Teck RC data to determine areas of metallurgical interest within the project. As drilling transitioned from RC to diamond drilling, core that was considered representative of the resource was selected and subjected to MLA mineralogy analysis. When coupled with sequential copper analyses this allowed calibration of an assay derived mineralogy model, allowing process concept options and a preliminary test program to be developed. This Phase 1 test program provided a preliminary process design, operating costs and anticipated concentrate grades and recoveries. Both this data and resource estimation were used to generate a preliminary Whittle pit optimisation based on maximising net smelter return, which in turn fed into a preliminary mine plan. The preliminary mine plan, in conjunction with geological logs and core results was used to develop a phase 2 metallurgical test program, where variability tests were conducted throughout the resource and composites formed to investigate specific years of the mine plan in locked cycle flotation. In addition comminution tests were modelled against geometallurgical domains allowing comminution components values to be calculated for 36?000 m of core. A flotation geometallurgical model was developed and incorporated into the resource model allowing concentrate grades and recoveries to be estimated on a block-by-block basis.

Sep 5, 2011