Search Documents

By M Norbert, P Mok

The mainline running tunnels for Legacy Way comprise of two-lane tunnel boring machines (TBM) driven tunnels. The length of the TBM tunnel section is approximately 4.2 km. The TBMs employed are double shield TBMs. Typical support to the segment ring while advancing a double shield TBM comprises of filling the excavated annulus between the ground and the segmental lining by injecting pea gravel, followed with primary grouting to fill between the pea gravel some distance behind the excavated face. The methodology adopted for the Legacy Way project, however, did not follow this typical approach, instead, two component grouting of the annulus was carried out.Where the annulus is typically filled with pea gravel, support is provided to the segment ring very close to the end of the tail shield, whereas in the case of two component grout this is not practical as the risk of grouting in the tail shield is high. The staging of the two component grout injection, the grout early age strength properties become key issues in ensuring that the segment ring leaving the TBM tail shield is stable and can support the necessary external loads.Two-component grout is a grout with two components, cementitious grout (component A) and accelerator (component B), commonly adopted for earth pressure balance (EPB) TBM. The grout reaches its thixotropic state in a matter of seconds providing initial support for the segment rings. Manual injection of two component grout to fill the bore annulus was carried out in stages leaving a portion of the segment rings unsupported. Ring stability during TBM advance was provided by a combination of ram thrust and the segment circumferential joint shear connectors.This paper outlines the design considerations such as rock load derivation by probabilistic analysis carried out utilising the software JBlock, 3D finite element analyses using the software Strand7 for ring stability and the testing and back analysis of the shear connector load bearing behaviour. In particular, the actual available capacity of the shear connectors against their published capacity by supplier was discussed.CITATION:Mok, P and Norbert, M, 2014. Tunnel boring machine excavation stability – double shield tunnel boring machine advance with partially grouted annulus, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Hall, D Kratochvil, P Littlejohn

Economic recovery of gold from complex gold ores, including poly-metallic deposits, is impacted by the presence of cyanide-soluble base metals. These base metals can create both a metallurgical challenge plus waste handling and disposal challenges. Base metals such as Cu and Zn compete for the cyanide reagent and often increase the total cyanide consumption to the point of making precious metals recovery uneconomic. In addition, the accumulation of base metals in cyanide solutions represent a challenge for cyanide detoxification and waste water treatment as these metals report to waste sludge. Such sludge requires safe handling and disposal, with possible long-term liabilities.Base metal interference can be removed with sulfidisation-acidification-recycling-thickening (SART) process technology. SART liberates the base metal from the cyanide complex and precipitates the metal as an insoluble sulfide product that can be recovered as a commercial grade concentrate. With the base metal precipitated, the cyanide can be regenerated as free cyanide and recycled to the gold extraction circuit.BioteQ completed laboratory testing for two projects, one employing cyanide leaching of copper-gold sulfide flotation concentrate and one employing a Merrill Crowe process, to determine the effectiveness of SART to remove and recover Cu and Zn in high-grade sulfide concentrates and to reduce the impact of cyanide-soluble metals on gold recovery and cyanide consumption. This paper will provide an overview of the testing methodology and results along with a review of the potential for SART to be applied to complex gold ores with poly-metallic deposits to improve project economics, operability and waste management.CITATION:Littlejohn, P, Kratochvil, D and Hall, A, 2013. Sulfidisation-acidification-recycling-thickening (SART) for complex gold ores, in Proceedings World Gold 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G B. Smith, G M. Marshall, A Querzoli

The South Australian mining regulatory framework has adopted a performance based approach to the management of risk. This approach has been in place in South Australia for more than 10 years and is increasingly being implemented in mining jurisdictions in Australia and around the world. Performance based regulation focuses on setting appropriate environmental outcomes to be achieved based on an assessment of the potential impacts associated with the development, operation and closure of mining projects. Measurable compliance criteria, including completion criteria, are set to demonstrate achievement of the outcomes. It is the responsibility of the proponent to propose designs and strategies that will achieve the regulated environmental outcomes and to demonstrate the implementation of their designs and strategies will achieve the outcomes into the future. Tailings Storage Facilities (TSFs) are significant elements of many major mines and each is unique with site specific factors such a materials to be stored, design, size, location, climate, sensitive receptors, operating history of the facility (i.e. changes to design), site culture and company capability amongst a range of other factors. Consequently a fit-for purpose approach is a key principle of best practice regulation of tailings management as it takes the site specific factors into account in setting appropriate outcomes for mitigating the identified impacts associated with a proposed development. Achievement of those outcomes through fit-for purpose, well designed management strategies would ensure safe, stable and economic storage of tailings in a manner that complies with all legislative requirements and presents negligible public health and safety risks. Tailings storage must also have acceptably low social and environmental impacts, both on and off site, during operation and indefinitely post closure. Achievement of environmental outcomes during operations and at mine completion can then be demonstrated to the regulator and community through public reporting of compliance with measurement criteria which establish the appropriate level of impact for each individual operation. A number of new mining proposals including tailings storage facilities (TSF) have recently been assessed and approved in South Australia. The location, size, design, sensitive receptors, public interest and therefore risk profiles of these TSF’s have varied substantially between these new mining proposals. These considerations were reflected in the assessment of the TSFs and the resulting mining lease conditions of approval including the environmental outcomes to be achieved over the life of the facilities. This paper and the accompanying presentation will provide case studies of recently approved TSFs within South Australia and the regulatory framework for each case.CITATION:Smith, G B, Querzoli, A and Marshall, G M, 2018. Tailings regulation – a South Australian perspective, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 166–177 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B Gyngell, P Culvenor

Large language models (LLMs) have generated a lot of hype since ChatGPT was released in early 2023. In essence, they allow people to interact with computer systems through natural language and have the ability to generate highly complex text, images and videos (Patil and Gudivada, 2024). It is clear that this technology has significant potential, however most mining companies have not yet found practical applications for it within their operations. In this paper, we present a range of such applications along with the tactical considerations associated with developing and implementing them. We have identified use cases across a variety of operational and functional areas within the mining industry and evaluated them based on their potential business value and ease of implementation. Firstly, we provide an overview of how LLMs work and a review of how LLMs are being applied in other industries to provide best practice inspiration for mining. Next, we present a list of possible applications in mining and a critical assessment of each use case. This section also includes a technical deep dive into the different methodologies for developing the technologies as well as an analysis of barriers to adoption within mining organisations. Finally, we share a discussion of the potential path forward for LLMs in mining and the impact they could have on the industry. We analyse the potential differences between early adopters and laggards in the artificial intelligence (AI) space. This research draws on interviews and surveys with artificial intelligence experts as well as mining subject matter experts to connect cutting edge thought leadership with the specific problems faced by our industry.

Sep 1, 2024

When studying minerals degrees at university, all the emphasis is towards sending the graduates into the bush to work at a remote mine; however, that is not the only option available to new graduates. There are positions in equipment supply companies, commercial laboratories, research organisations, engineering companies and contractors of many types. The aim of this paper is to show metallurgy graduates that there are non-mine site based career options available to them that offer outstanding career development. This is illustrated by outlining the research being undertaken by Magotteaux Australia and by telling the story of a graduate metallurgist working in MagotteauxÆs small research group. Magotteaux is an international supplier of grinding media and wear resistant components for the mining industry. The Australian research group is focused on determining the effects that the choice of grinding media has on subsequent processing, for example flotation and leaching, by using newly developed tools and techniques.

Jan 1, 2006

By J M. Galvin

The traditional engineering approach to assessing stability is based on comparing resisting force (capacity) to driving force (demand), or strength to working stress. In underground coal geomechanics, considerable effort has been expended on quantifying the strength of rock structures. However, this has not been matched by advances in determining the load acting on these structures, reflecting a reluctance by some to embrace numerical modelling to assess load magnitudes and distributions. Numerical modelling is a valuable aid as loading environments are a function of both the stiffness of the mine workings and the stiffness of the superincumbent strata and are statically indeterminate in most cases.This paper defines stiffness, which is often confused with elastic modulus. It shows that, effectively, stiffness encapsulates geology, depth of mining, panel width, pillar width and mining height. Therefore, these factors are variables that need to be taken into account when determining stress magnitudes and distributions about mine workings. A range of examples are presented that illustrate the significance of the stiffness of the superincumbent strata on surface subsidence; the magnitude and distribution of pillar and abutment load; and aspects of bord and pillar mining, pillar extraction and longwall mining. These examples provide bases for identifying the limitations of some empirical approaches to mine design, identifying how to compensate for some of these in design processes; and emphasising the need to make greater use of numerical modelling in understanding and quantifying loading environments in underground coal mining.CITATION:Galvin, J M, 2014. The significance of superincumbent strata stiffness and its impacts on coalmine design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By N Murthy

Alumina is a major impurity in Australian iron ores and as the higher grade ores become depleted there will be a stronger focus on treating lower grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the alumina content. High alumina in iron ore is deleterious in that it can:• produce slags with lower desulfurising capacity,• reduce sinter/pellet strength and quality, and• produce higher slag volume and increase slag viscosity.Meeting iron ore quality specifications for alumina by blending ore from different sources will eventually be insufficient. Hence, innovative flow sheets based on new and commercially available technologies will be required. Their advantages and disadvantages, the testing methodologies and the challenges and diffi culties involved in reducing the alumina content of iron ores are presented and discussed.

Jul 11, 2011

By M A. Tuck

Atmospheric air on a moisture free volume basis consists of approximately 21 per cent oxygen. The current minimum threshold for oxygen in Australia is 19.5 per cent. Atmospheric air generally will also contain water vapour and will also pick up further moisture as it flows around a mine ventilation network. This paper details the results of a study to determine how much oxygen depletion can occur due to the sole impact of increasing the moisture content of air and the potential impacts of this on ventilation system design. The study shows that the moisture content can have a significant impact on the oxygen concentration in mine air. The main factors controlling the impact are the barometric pressure, dry bulb temperature and relative humidity of the air.CITATION:Tuck, M A, 2015. What is the oxygen depletion potential of ?water vapour?, in Proceedings The Australian Mine Ventilation Conference, pp 173–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

By G York

South African gold reserves extend to great depths. However, strategies for the mining of such deposits have changed only slightly over the past number of years. Regional support at depth is currently provided by rock pillars and backfill. Many problems have been experienced with these regional support practices at deeper levels. In this paper several alternative forms of regional support are described which include the use of concrete, the use of back area caving and confinement to strengthen pillars. These new concepts are supported by numerical and laboratory modelling and in situ results.

Jan 1, 1998

I have headed this paper with a question and for the impatient among you ûthe answer is no we have not run out of developments but, and it is a big æbutÆ, we need to be innovative and ahead of the game or ænoÆ will be æyesÆ before we know it.Why do I believe that our future lies in innovation? Thirty years ago, knowledge doubled every 14 years. It is now doubling every seven years. In 1965, Gordon Moore, one of the founders of the chip maker Intel, made an observation that growth in memory chip performance is doubled every 18 months which became known as MooreÆs Law. Now there is fibre law, where the transmission line capacity doubles every nine months and storage capacity, under disc law, doubles every 12 months. What does this mean? Well, firstly there is a massive rise in information flow and availability with no limits in growth for at least the next ten years. Secondly, unlike our grandfathers, we are most unlikely to be employed by the same firm for our working career - we may not even have the choice to stay with the same company. In a phenomenon Richard Foster and Sarah Kaplan (2001), borrowing from Schumpeter, termed æcreative destructionÆ, companies are unable to sustain market-beating levels of performance for more than ten to 15 years. In the 1920s the turnover rate of companies in the United States was 1.5 per cent, so a company could employ almost three generations from the one family. A company had a half life of 60 years. In other words, you could well be in the same working environment as your grandparents. Today the churn rate is estimated to be eight to ten per cent. A company has a half life of five to six years. So for large companies, as an employer or employee or as a contractor, your working environment has a 50 per cent chance of changing in five years. Innovation is the driver of this rapid rate of change. Innovation is not for the faint hearted (Cutler, 2001) but it is the core for success in the global economy. The rate of change in our world is not going to decrease. We must learn, not only to manage change, but to enjoy the process of changing û to ride the tsunami of the knowledge economy.

Jan 1, 2002

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

Spatial continuity as described by a variogram is a reflection of the underlying mineralisation/geology. Modelling of the spatial continuity (variogram) must account for both the quantitative data (ie sample grades), on which the variogram calculations are based, and the qualitative information as provided by the geological interpretation. An understanding of the geology and the variogram interpretation tie together the sample values and allow us to go beyond the actual data (Journel, 1995). Variography makes geology transportable and allows the geological interpolations to be channelled downstream into mine planning, ultimately affecting the economic decisions surrounding a deposit. As such the process of variography and resource modelling is critical. Thus consistent expert decisions need to be made which force geologists to have a closer look at the available information and the geological interpretations. The aim of this paper is to provide an overview of the latest developments in visualising variography and to demonstrate their usefulness in decisions regarding the spatial continuity of mineralisation. New ideas concerning potential future developments in visualising and modelling spatial continuity through variography are introduced.

Jan 1, 1996

By Ribicic M, Kocar F

Surface lakes or water accumulation present a possible threat for the flooding of the underground mining works. Therefore, the criteria that define the conditions under which no flooding of the mining works can occur are of vital interest to the miners. The authors present the criteria that they developed for the Velenje lignite mine, Yugoslavia, and that take into account the elastoplastic behaviour of the rocks and the natural stresses involved in the deformable strata between the bottom of the lakes and the mine works as well as the extent of the direct caving-in process resulting from longwall mining activity. Fi- nally a generalization of these criteria to the other rock and stress conditions is discussed.

Jan 1, 1988

By R Rodriguez, S Gumo

The Lihir Gold Mine, in Papua New Guinea, is a large open pit operation within an active geothermal system inside a collapsed volcanic crater. This unique setting has a big impact on the mine operation because of the occurrence of geothermal hazards. The system for managing geothermal hazards that has been developed by Lihir Gold Mine is a pioneering effort that can be applied to future mine discoveries in a similar environment. The controls are integral to the mining operations and allow mining to proceed whereas without them mining could not be considered. Truck and shovel productivities in conventional open pit operations are constrained by diggability, equipment availabilities and utilisation. At Lihir, additional constraints are in the form of 100 m exclusion zones around working shovels and 50 m exclusion zones around working drills. Given that the mine has seven large digging units and six drills, this amounts to a lot of area that excludes the presence of people on the ground. So how are the necessary work like grade control, survey, blasthole loading, and in-pit maintenance performed safely to achieve production targets? The answer is in the highly specialised procedures that have been developed that utilise geological, geothermal and geotechnical knowledge to predict problem areas and also deal with the organisation of movement in the pit for people and mining equipment. This paper will detail how scheduled material movement can be maintained despite the challenging conditions faced at Lihir Gold Mine.

Jan 1, 2007

The segment of the Upper Cenozoic volcanic chain (CVZ) located on the western border of South America (16-28¦S lat.) is constituted by an association of strato- volcanoes and ignimbrite sheets, with high K calco-alkaline affinities. Strata-bound volcanoes, mainly of andesitic and dacitic composition, present along the whole chain, and various hydrothermal alteration zones, on the slopes and in the cores of eroded volcanic structures. Some of these altera- tion zones bear epithermal precious metal ores and sulphur deposits, which at present are being exploited. The studied Salar de Gorbea area, located in the Andes of northern Chile (25-26¦S lat.) contains a numer- ous group of Miocene to Quaternary stratovolcanoes, with advanced argillic and extreme silicification hydrothermal alteration in their cores and on their slopes, favoring the formation of great volumes of alunite within altered zones and sulphur deposits in the higher parts of the volcanic edifices. Simultaneously, siliceous hydrothermal breccia of the phreato-magmatic type, with evidences of hydromag- matic explosions are recognizable, allowing, in some cases, the ascent towards the surface of rock fragments belonging to the Paleozoic pre volcanic basement. Radiometric ages obtained in some of the hydro- thermal alteration zones (K-Ar in alunite) are slighty young- er than the unaltered rocks which constitute the strato- volcano. Trace element (Hg, As, Sb, S, Au, Ag, Cu, Pb, Zn, Mo) patterns in orientative rock samplings show that the studied alterations zones correspond to high sectors of the cpithermal system, without evidences of metallic minerali- zation on surface. The weak erosive action due to the ex- tremely and climatic conditions in this segment of the Andes, has not allowed the cropping out of deeper areas of the hydrothermal alteration zones, in contrast to other Miocene more eroded volcanic edifices and Miocene vol- canic terranes of the Andean Range.

Jan 1, 1987