Search Documents

By John W. Cloud

In 1877 the Pennsylvania Railroad Company removed an old bridge from its line at Duncannon, Pa., built intermediate piers and erected shorter spans of the Pratt truss type, which had previously been in use on another portion of the road. The design of this truss would not admit of diagonals larger than 19 inches diameter, and in order to stiffen the bridge somewhat steel rods were introduced for the main diagonals in the first and second panels, 19 inches and 18/8 inches diameter respectively. These rods were threaded without upsetting, and by the ordinary formulae the strains were of the same intensity upon both, viz., 16,000 pounds per square inch with the maximum loading. The other main diagonals in the truss are 19 inches diameter, and of iron. It was specified for the steel rods: Elastic limit,.......46,000 Ibs. Tensile strength,. .. ,. .. 80,000 lbs. Elongation,,.,.,. 20 per cent. The steel was procured without difficulty, and it allowed a factor of safety of 23/4 at elastic limit, while a similar factor of 2½ had for a long time been successfully used for iron. In the course of three years, from time to time, six of these steel rods broke, three of them being 18 inches in diameter, and three 19 inches in diameter. The broken rods were tested, and three of them analyzed at Altoona to ascertain the cause of failure, and what modifications should be made in the steel for such service. Examination showed that all the rods were broken in detail close under the nut. The threads were well cut and properly rounded at the root. testing the rods micrometer screws, reading to .0001" with c bell to signal the contact, were attached to the test pieces, and by this means the modulus of elasticity and elastic limit accurately obtained.

Jan 1, 1881

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By James R. Swaisgood, Ronald E. Versaw

Hundreds of shafts have been sunk in the United States in the past. Most of these have been successful however, in some instances thousands of dollars have been lost due to work stoppage while emergency measures were taken to control unexpected water flows. In cases where it was not possible to control the water, the shafts were completely lost. Many thousands of dollars have also been wasted in overconservative support design for the successful shafts. These "hell for stout" designs were necessary because of the importance of the shaft in the operation of the mine. If there was trouble in the shaft, all underground operations would come to a halt. Over-design was also necessary because no reliable preconstruction investigation methods or rational support design methods were available.

Jan 6, 1974

Beyond the industrial suburbs of Melbourne to the southeast are brown coal deposits just under the fertile soil of the Latrobe Valley. These deposits rank as one of the wonders of the world. The manner in which this resource is put to use is one of the great engineering accomplishments of our time and also a prime example of Australian elan. The brown coal, with over 60% water content, occurs in beds from 200 to 400 ft thick, under 50 ft of cover. Fifty thousand tons of coal per day move in a nearly continuous stream from mining face to boilers. The power plants supply two thirds of the State of Victoria's requirements, about 800 megawatts. Surge capacity between mine and power plant is sufficient for 12 hr steaming time! Victorian brown coals have been known since the middle of the 19th century. However, it took a strike of bituminous coal miners in 1915 to bring brown coal permanently into the picture as a fuel for power generation. In Australia, power generation is a State function. The great development of brown coals has been under the State Electricity Commission of Victoria.

Jan 10, 1964

By John D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space.

Jan 9, 1959

By Fred A. Anderson, George B. Wallace, Edward J. Slebir

Auburn Dam will be a thin, double-curvature concrete arch dam about 685 ft high. With a crest length of about 4000 ft, it will be the world's longest single-arch dam. The site is located on the North Fork of the American River about 40 miles northeast of Sacramento, Calif. Construction is scheduled to get under way in 1970. In planning for the design and construction of Auburn Dam (see artist's conception), the foundation material, with its various discontinuities, is being investigated and the structural characteristics of the rock mass evaluated. The investigation and testing programs will aid in defining the pertinent geologic features and their individual and cumulative influence on the foundation. The work includes geologic surface mapping, surface trenching, core drilling, geophysics, tunneling, excavating shafts and raises, performing in-situ tests, and conducting laboratory tests on core and block samples. Competent amphibolite is the predominant material in the foundation, but significant bodies of chloritic, talcose, and metasedimentary rocks, a strongly developed jointing pattern, faults, and shear zones also affect the deformability of the rock mass. A comprehensive rock mechanics program, closely coordinated with geologic investigations as well as the engineering studies, therefore is required The rock mechanics work is a combination of many analytical studies and experimental investigations. The experimental work includes laboratory tests on core samples from holes drilled for geological studies of the entire foundation and in-situ tests performed in selected areas. The laboratory testing program evaluates the general properties of all important rock types and aids in correlating many of the key structural features encountered within the foundation. To derive maximum benefit from the field tests, they are conducted in materials which represent a

Jan 1, 1970

By W. A. Bruce

THIS paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to sell-spacing problems are shown.

Jan 1, 1942

By authority of the Secretary of War, and in response to frequent requests, the following suggested list of reading is issued by the War Department for the information of civilian engineers desiring to inform themselves on military subjects: These references have been selected, first, with a view to giving to engineers unfamiliar with the art of war a general survey of that sub-

Jan 1, 1916

By George Smith

IN discussing present-day business and industrial troubles we easily drop into the habit of clinical diagnosis. Talk of this kind, with its emphasis on suspicious symptoms and abnormal tendencies, makes us all morbid. As an English essayist has put it, we may thus induce a melancholy, temper that simply in-vites the ministrations of social and political quacks. It is far better-because nearer the truth-for us to recognize that our condition is in no sense diseased, that our body politic, social and economic, is suffering merely from growing pains; that America is not de-cadent-indeed, that any lapses from staid normality are traceable to the, excesses of youth. Our chief .trouble, then, is only that our industrial state is still young; it may be that we have been growing too fast. The growth in the industrial development of our country from pioneer days to the present time has been marvelous. Too many of us, however, take all this as a matter of course-we credit this record of American progress to our American genius alone. Too often we overlook the fundamental relationship between resources and progress-that man is aided and even guided by Nature. The fact is, social advance, indus-trial progress, national prosperity all have their ma-terial basis in natural resources. In furnishing the needed mineral raw materials to the great manufac-turing industries of the United States there has been no halt, but rather a general acceleration. No other phase of American activity can show-equal advance. As the decades have passed, the winning of mineral wealth has progressed from the role of a stimulus for western exploration to that of the foundation for nation-wide business. In 1890 the Sherman law was passed; since then the population of the United States has about doubled. Since then, too, thevalue of the annual product of the mines of this country has increased better than eight-fold-from 650 millions to 51/ billions of dollars. Since then the four largest branches of the mineral industry, which supply the iron and copper, the bituminous coal and petroleum-the bone and sinew and the energy of all other American industries-have increased their annual output nearly ten-fold as to value and six-fold as to quantity. Such a growth in the volume of mineral output must be taken as a true measure of the ex-ceptional service rendered by the mines of the United States. Not only is this a much larger country than it was 38 years ago, but its growing mineral industry has met demands that have been out of all proportion to the growth of the population.

Jan 8, 1928

By John C. Robison

INTRODUCTION Sensitivity analysis is a means of gauging the impact of individual risks on a financing. Key risks can occur in three time periods: - Feasibility, engineering and construction phase; - Start up phase (usually through completion); - Operating phase (post completion). If a company has agreed to cover these risks prior to completion, then less attention will be paid to the sensitivity of the project in the first two time periods. Since the operating phase of the project generates cash for both operations and debt service and generally does not begin until two to six years after the loan is signed, it is wise to look at scenarios other than the projected "base-case" scenario in order to determine the project's capability to operate successfully under a broad range of probable future events. Lenders are compensated at a fixed spread over their borrowing base and generally are not compensated if the project is successful beyond expectation. They are also subject to the loss of principal plus funding costs if the project performs below expectation. Because of this, lenders establish sensitivities around the parameters of conservative projections developed in the project feasibility studies and the cash flows resulting from these projections. The initial cash flow projections should demonstrate the project's ability to meet cash costs, debt service requirements (principal and interest), and still have sufficient cushion to cover contingencies such as strikes, price fluctuations, force majeur situations, etc. (See Schreiber, Chapter 10). The selection of the level of sensitivity analysis to be performed is the result of both objective criteria, including probabilistic analysis applied to the technical parameters, and, of equal importance, subjective criteria applied by the analysts, especially with regard to the economic and financial parameters impacting the project cash flows. RISK SENSITIVITY Assumptions used in the cash flow projections should be realistic. Risks identified by the lenders should be identified and cash flows prepared to assess whether these project risks are acceptable. Typical project risks include the following (see also Chapter 9): - Sufficient reserves - quantity and quality - Product price - Production level - Operating costs - Availability of energy and supplies - Transportation and infrastructure requirements and costs - Interest rate - Completion risks - Tax level - Political risks - Cost over-run risks - Operator experience - Management - Technological risks - Environmental permits and risks - Foreign exchange risks - Insurance coverage - Equity of sponsors - Inflation rate - Capital expenditure during project life In order to see the effect on the cash flow projections, each risk should be analyzed for its impact on the cash flow generating capacity of the project. Sensitivities can be examined to see if the resultant cash flow projection will meet the lenders minimum credit standards. 1.Reserve Sensitivity In general, lenders will not assume the reserve risk. However, it should also be noted that lenders receive loan proposals in which reserves range anywhere from proven to possible. Sensitivities are not generally run for various reserve levels and reserve estimates are either considered acceptable or not acceptable by the lenders.

Jan 1, 1985

By John J. Curzon

The existence of mineralized ground in the area near Lake Chelan has been known since 1887, when Major A. B. Rogers, a locating engineer for the Great Northern Railway, came up Lake Chelan to Railroad Creek in search of a pass over the Cascade Mountains. The steep mountainsides near the crest of the Cascades proved too difficult for railroad construction, and the project was abandoned. Upon his return to Seattle, Major Rogers apparently told his friends, the Denny family, about the large, red, oxidized patches he had seen on the valley walls along Railroad Creek. The Dennys, being true pioneers in spirit, grubstaked J. H. Holden to explore the area and to stake any promising mining ground, and thus began the chain of events that culminated in the construction of the plant that is now known as the Chelan Division of the Howe Sound Company. Holden staked the first group of claims in 1892. Soon afterward, A. H. Murdock, who was then a storekeeper in Chelan, and who is still living at Waterville, and his partner, W. P. Robinson, staked adjacent ground. These two groups of claims formed a substantial part of the mining property being worked today. During the period from the original staking in 1892 up to 1928, when the Britannia Mining and Smelting Co. optioned the property, many attempts were made to bring the property into production, through the formation of several stock companies and by examination and testing by engineers from several well-known mining companies. Although the Britannia organization optioned the property in 1928, not much was done until 1930, when a subsidiary was formed—the Chelan Copper Mining Co.—to explore further the possibilities of the ground. Some work was done during the next few years, but it was not until March 1937 that the Chelan Division of the Howe Sound Co. took over with a program of "full speed ahead," and active development of the mine and construction of the complete plant was begun, including docks, tug and barges, 54 miles of power line, 11 miles of road, mill, shop buildings and complete camp. Production began in April 1938, and has continued without interruption, except for regular change days and holidays and a six-weeks strike in 1939. This interval of time has seen the gradual evolution of a mine and mill originally planned for a rate of 1000 tons per day into a compact operation that last year averaged 2264 tons per operating day. This operation, although rather small when compared with the large copper producers of the Southwest, is important to the state of Washington for several reasons: It has provided employment for several hundred people continuously since construction days in 1937; it has helped materially in the war effort, through production of vital copper and zinc, without which no war can be won; and last, but not least, it has conclusively refuted the old pessimistic arguments that a successful mine would never be found in the Cascade Mountains of Washington. The Holden mine has been producing

Jan 1, 1946

By Robert M. Doerr

A method, based on radial distribution analysis, was developed for determining the effect of size to which a given ore is broken on the potential recovery in beneficiations targeted to selected concentrate grades. A measuring microscope and computer analysis are used to obtain the radial distribution of the valuable component in polished sections of ore.

Jan 1, 1975

By G. J. Cardwell

The rock and mineral analyst will be called upon to determine both the major and minor constituents in materials as varied as rocks, soil, sediments, concentrates and various liquids. These analyses will have interactions requiring extraction, matrix modification, and background correction. Analytical methodologies include classical gravimetric methods, such as fire assay, emission spectroscopy, X-ray fluorescence, atomic absorption, inductively coupled plasma, and neutron activation. With these capabilities the analyst can be called on to determine three-fourths of the elements in the periodic table. How can the earth scientist pick the method best suited for his particular sample?

Jan 1, 1984

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples.

Jan 9, 1959

By H. K. Work

THE Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of steelmaking are partly economic and partly metallurgical.' In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect-it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Bessemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (I) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. THE CONTROL PROBLEM In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985

By Pramod C. Thakur

Introduction Methane is contained under pressure within the fractures and adsorbed on the surface of the coal seams and adjacent strata. It is released into the mine atmosphere during mining of the seam creating explosive gas-air mixtures. Large volumes of air, sometimes as high as 20 tons of air for each ton of coal mined, are circulated constantly to dilute and carry away methane from coal mines. Removal of methane from solid coal, wherever high methane emissions occur, has been discussed by Spindler and Poundstone (1960) and Thakur and Davis (1977). Methane control in longwall gobs is much more complicated. As longwall mining progresses, the overburden continually subsides, and the immediate roof caves behind the roof supports. Even the underlying strata heave and open up communication channels feeding gas to the longwall gobs. The pressure of gas in the underlying and overlying strata is usually higher than the ambient air pressure in the mine. Thus the mine workings become natural pressure sinks, into which gas flows from the entire disturbed zone. Winter (1975) defines this zone as the "gas emission space". Depending on the number of gas-bearing zones in the gas emission space and their gas contents, the total methane emission from longwall gobs could vary from a few to more than one hundred cubic meters of gas per ton of mined coal. Hence the ventilation of longwall faces demands a large quantity of air. This ventilation need is further enhanced by high air losses specially on caving faces (with no stowing of the gobs). The old system of longwall ventilation, the 'U' pattern, where all the air was brought down one gate road and exited through the other gate road, loses large quantities of air through gobs giving a high methane concentration at the return end of the face. The 'Y' ventilation pattern where intake air is brought down both head and tail gate roads relieves the situation to some extent but, on most longwalls, some kind of methane control is still needed. With the onset of longwall mining in Europe several decades ago, the initial work on methane control on longwall has naturally been done there. The basic principle of methane control has always been, and still remains, some means of "bypassing methane from the gas emission space without letting it mix with the mine air". In most cases the bypassing mechanism is either a strategically located borehole or a roadway. A successful methane control program depends on the following basic premises: a. Determination of the geometry of the gas emission space and location of gas bearing horizons therein. b. Estimation of the rate of methane influx into the longwall gob. c. A scheme to bypass the gas in the most economic and efficient manner and thus prevent it from entering the mine atmosphere. In successful methane drainage programs a high proportion, usually between 50 and 70 percent, of the total gas emissions in a working district is removed before it can enter the mine airways. Advantages of methane drainage can be summarized as: 1. Generally reduced methane levels in the mine leading to increased safety and productivity. 2. Reduced air requirements and corresponding savings in ventilation horsepower. 3. Faster rate of advance for development headings and economy in the size of headings. 4. Possible use of mine gas as an additional source of fuel. The purpose of this paper is to briefly review the geometry of gas emission space and methane influx therein and discuss more successful European and U.S. longwall gob gas control techniques.

Jan 1, 1981

By Ernest A. Hersam

Accurate ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fineness of the pulverized product. Fine screens are expensive, easily injured by misuse, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to be actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

Jan 1, 1907

By J. C. Osler

The design of a tailings dam is a geotechnical engineering project of considerable scope. For the design, it is necessary to establish the engineering properties of the soil or rock strata which will support the dam and the tailings or other fill which will be used to construct the dam. The various field and laboratory investigations which are necessary to obtain the required design parameters are discussed in the paper and the use of these parameters to compute stability, settlement, and seepage are considered. The designer of a tailings dam can never assume an absolute knowledge of the properties of the foundation strata. Further, initial design assumptions are often approximate, particularly with regard to the distribution of pore pressures through and beneath the dam. Thus, the installation of performance monitoring instruments is recommended, since data obtained from such instrumentation can be used to check the stability of the structure both during construction and after its completion.

Jan 1, 1972

Report of Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -I herewith present a report of some of the more important activities of the Institute for the year of 1922. The outstanding feature of the year is the optimism felt by our members despite the continued depression in the mining industry. January 1, 1921, found many of our members out of employment or drifting into other industries to tide them over the depression; but almost universally the feeling has been that this was but a temporary condition and that sooner or later the necessary production of raw materials would enable these members to return to their former activities and renew their participation in Institute affairs As the year passed conditions improved and, before it ended, many had found employment in their previous occupations. Bearing in mind that this depression has been very real, we have reason to be well satisfied with the work that the Institute has been able to do The loss of members through inability to pay dues has been large, and income has been correspondingly reduced, but it proved to be materially in excess of that anticipated early in the year, so that a substantial and unanticipated balance was carried forward toward the activities of 1923.

Jan 1, 1923