Search Documents

By Gail F. Moulton

In spite of an increase of 7 cents per barrel in the posted price of oil for the Panhandle field effective June 16, 1943, there was less drilling during 1943 than ir, any of the several previous years. The drilling statistics are compiled as Table 2 and show the material increase in the percentage of the total number of field wells completed as dry holes. This increase suggests that the productive area of the field is largely drilled up on the well-spacing pattern now followed and that new discoveries will be required to permit any important new activity in the area. The fact that only four wildcats were drilled in the area during the year indicates that some new prospecting technique or some ncw point of view is required to stimulate exploration. No new producing areas were discovered during 1943 and no additions to oil reserves were made through extensions or discovery 'of new pays. Accordingly, the proven reserves in the area declined by the amount of the production, or nearly 31 million barrels. These results of drilling are similar to those obtained during 1942, whcn no new oil areas were discovered as a result of wild-catting, a total of five wildcat wells in 1942 resulting in four failures and one gas-fieid discovery of undetermined merit. sion. The number of oil-producing wells reported by the Commission increased during the year by 163 to a total of 5576 as of December.

Jan 1, 1944

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By L. H. Dushak

DURING the war period of quicksilver activity there were a number of departures from what may be termed the classical quicksilver metallurgy. Attempts were made to beneficiate low-grade ores by gravity concentration and flotation; mechanical furnaces began to replace the Scott furnace and the vertical coarse-ore furnaces, and condensers of sewer tile and redwood tanks were used in place of the older brick and stone condensing chambers. Other developments that have occurred during the current period of quicksilver, activity are mainly in the nature of improvement and further refinement of those started during the war period. Each period of quicksilver activity has been accompanied by the proposal of various new processes, including wet methods for the treatment of quicksilver ores and innovations in furnaces, retorts and condenser equipment. As far as the author knows, nothing of economic significance in the way of "new processes" has been developed. There is in fact no real need for any essentially new process for the treatment of quicksilver ores; the direct furnace treatment is simple and inexpensive. Moreover, with fare exceptions, the quicksilver industry has no complex or refractory ore problems corresponding to those which are receiving more and more attention from metallurgists in other branches of the nonferrous field. Under these conditions improvements in quicksilver metallurgy must be looked for through the adaptation of current developments in engineering and metallurgy generally to the particular needs of quicksilver practice rather than through the invention of new processes.

Jan 1, 1930

By L. H. Dushak

DURING the war period of quicksilver activity there were a number of departures from what may be termed the classical quicksilver metallurgy. Attempts were made to beneficiate low-grade ores by gravity concentration and flotation; mechanical furnaces began to replace the Scott furnace and the vertical coarse-ore furnaces, and condensers of sewer tile and redwood tanks were used in place of the older brick and stone condensing chambers. Other developments that have occurred during the current period of quicksilver activity are mainly in the nature of improvement and further refinement of those started during the war period. Each period of quicksilver activity has been accompanied by the proposal of various new processes, including wet methods for the treatment of quicksilver ores and innovations in furnaces, retorts and condenser equipment. As far as the author knows, nothing of economic significance in the way of "new processes" has been developed. There is in fact no real need for any essentially new process for the treatment of quicksilver ores; the direct furnace treatment is simple and inexpensive. Moreover, with rare exceptions, the quicksilver industry has no complex or refractory ore problems corresponding to those which are receiving more and more attention from metallurgists in other branches of the nonferrous field. Under these conditions improvements in quicksilver metallurgy must be looked for through the adaptation of current developments in engineering and metallurgy generally to the particular needs of quicksilver practice rather than through the invention of new processes.

Jan 1, 1930

By Kenneth C. Vincent, A. M. Gaudin

TEN years ago Taggart, Taylor and Ince1 described a workable, convenient apparatus for the measurement of contact angles between cleaved, ground or polished particles and captive bubbles. Wark and Cox2 and Wark and Sutherland3 have done an immense amount of experimental work with this apparatus. Their work has had as principal object the determination of "contact curves." Contact curves are cartesian charts in which pH (or some other variable) is plotted against quantity of modifying agent. The rectangular area is broken into two or more curvilinear areas separated by the contact curve. The curve indicates that a sharp demarcation exists between conditions that bring about sticking of particles to bubbles and conditions that do not produce sticking. The type curve appears in the TRANSACTIONS as Fig. 1, page 248, volume 112. Wark and Cox offer data to show that the contact angle has a value determined by and characteristic of the agent used. Wark and Cox also make the statement that they believe this value is independent of concentration (ref. 2a, p. 209). They say: It is suspected that, given sufficient time and provided that there are no disturbing factors, the full ethyl xanthate angle (corresponding to a complete xanthate film) would be obtained in every case where contact occurs. Such a conclusion, if correct, would tend to substantiate the hypothesis of flotation collection by metathesis championed by Taggart and his associates4-8 and would argue against the adsorption hypothesis now adopted by Wark7 and by one of us.8 However, the data of Wark and Cox do not bear out the conclusion that there is a sharp passage from conditions of contact to conditions of noncontact. Rather, they indicate the existence of a transition zone of reagent concentration across which the contact angle varies with changes in reagent concentration from zero to a value near the maximum. This may be seen, for example, from Fig. 195 in the new text by one of us (ref. 8, p. 380), which presents the data of Wark and Cox in graphical form. The object of this study has been to explore the nature of the transition from conditions of contact to conditions of noncontact. The data of Wark and Cox to which reference has been made as showing that a gradual transition exists are marred by the fact that the region of critical-agent concentration is at an extremely small concentration. This condition suggests that diffusion may have played such a preponderant role that equilibrium was not reached within the time alloted. In the Wark and Cox data, the critical concentration was at about one part of xanthate per million parts of water. To form a monolayer of xanthate on the mineral surface would therefore require depletion of xanthate in the liquid to a depth of the order of

Jan 1, 1940

By A. W. Schlechten, Ernest J. Breton Jr.

Experiments on the separation of copper and zinc ions by selective action of ion exchange resins showed the carboxylic type to be more effective than the sulphonic resins. The latter demonstrated a greater capacity over a wider pH range. Data show the effectiveness of resins as a means of concentration. IN recent years the restrictions of stream pollution laws and the high price of metals have created an interest in ion exchange as a means for metal recovery. Some applications have proved successful. In Germany during World War 11, 17 tons of copper per day were recovered from rayon mill wastes by means of ion exchange resins;' and for some time in this country a large ion exchange unit has been in operation for the recovery of copper from rayon waste water. The possibilities of applying ion exchange to the recovery of metals occurring in plating rinse water is particularly promising. In most of these applications only the metal being recovered occurs in the waste. The ion exchange resins act merely as a means of concentrating the metals to a point where they can be recirculated. It would be highly desirable to use ion exchange as a means of not only concentrating but also of separating metals. With the exception of the impressive separations accomplished in connection with the atomic energy program, very little has been done on metal separations.' Therefore, an investigation was undertaken at the Missouri School of Mines and Metallurgy to determine if either of the two main types of ion exchange resins could be used to separate metal ions in solution. The selective removal of copper ions from a mixture of copper and zinc on carboxylic and sulphonic-type resins was investigated as a function of flow rate, pH, copper-zinc ratio, and concentration. It was shown that zinc can be separated from copper and that very large ratios of concentration can be obtained using ion exchange resins. Since ion exchange is relatively new to the field of metallurgy, a brief review of the subject will be included. Theory of Ion Exchange A comprehensive theory for ion exchange has not been developed as yet, but the mechanisms are analogous to metathetical reactions: R Na + Cu++ *=? K(SO3)2 Cu + 2Na+ R is the designation for the ion exchange resin. If a copper solution is passed over a resin bed in the sodium form, two ions of sodium will be released for every ion of copper removed. For the most part this reaction follows the laws of mass action and of electrical neutrality. Consequently, if an excess of sodium ions is passed over a bed containing copper, the reactions will be reversed, and the resin will be regenerated to its original form. A few empirical rules governing the exchange reaction have been set forth: 1—In general ions with a high valence will replace ions with a lower valence. 2—Ions having higher activity coefficients have a higher replacement potential. 3—In a series of mono-valent ions, those with the smallest radii of hydra-tion will tend to replace those having larger radii of hydration. 4—Where ions are similar in most respects, those with the higher atomic weight sometimes will take precedence. This last rule is not as definite as some of the others. These rules apply to rather dilute solutions at moderate temperatures and assume all ions to be present in about equal concentrations. Higher concentrations and temperatures may in some cases reverse the normal exchange reactions. Ion exchange materials are unique in that their efficiency increases as the concentration of the solution decreases. For many exchangers, most efficient operation is obtained at concentrations in the order of one thousandths of a percent. Most applications, though, are made in solutions containing considerably higher concentrations than this. Coste9 as shown that ion exchange resins will remove aluminum and iron effectively' from solutions of up to 10 pct chromic acid. Ion Exchange Resins Ion exchange resins are insoluble, porous, resinous structures to which active groups have been attached. Active groups such as (—SO,,)- and (COO)- pick up cations; hence structures saturated with groups such as these are called cation exchangers. Structures saturated with groups such as (—NH,)' which pick up anions, are referred to as anion exchangers. The resinous structure of necessity is resistant to strong acids, bases, oxidizing, and reducing agents, and most of the common organic solvents. An idea of the stability can be gaged from the fact that resins last for many years under constant use without detectable chemical or physical breakdown. The ion exchange reaction is not confined to the surface of these synthetic resins. Its porous structure permits active groups in the center of a particle as well as those on the surface to remove ions. A high capacity resin such as Amberlite IR-120 will remove up to 3.3 lb Cu per cu ft of resin. In this investigation several approaches to the problem of separating copper from zinc by ion exchange were considered. First, if a reagent could be found which would complex one of these metals and not the other, then by passing this reagent through a bed of exchanger containing copper and zinc, the

Jan 1, 1952

By R. A. Garling

INTRODUCTION Since the infancy of in situ uranium mining, a growing number of hydrometallurgical processes have been incorporated into pilot and commercial scale flowsheets. Although initial design efforts were geared toward maximizing uranium recovery and minimizing plant and wellfield flow circuit maintenance, recent emphasis has shifted to improved means of water conservation and aquifer restoration. As mining units approached depletion, evaporation ponds reached minimum freeboard, and state and federal agencies demanded proof of groundwater restoration, processes including mixed bed and conventional ion exchange, reverse osmosis and electrodialysis were adopted by the industry. These units served the additional function of reducing process bleed flows during mining in states where the deep disposal well permitting ice remains unbroken. This report concerns the use of electrodialysis as an alternative to the more conventional processes used in in situ mining. In addition to a brief history and description of the process, a comparison to reverse osmosis and operational data derived from testing an Ionics, Inc. 1.31 x 10-3 m /s (30,000 gallon/day) unit at the Teton-Nedco Leuenberger Research and Development pilot will be presented. HISTORY Commercially practicable electrodialysis was contingent upon the development of synthetic ion exchange membranes in 1940's. In 1952, Ionics Inc. demonstrated that the process was amenable to the treatment of salt and brackish water and, in 1954, made their first commercial sale. The following decade saw several major electrodialysis unit sales which were generally targeted for use on private or municipal potable water treatment. Major increases in membrane desalting unit capacities, facilitated by technological advances in the reserve osmosis industry, were noted during the 1970's. The development of polarity reversing electrodialysis equipment which reduced feed pretreatment requirements, increased water recovery rates, and simplified unit operation, kept Ionics Inc. competetive in the water treatment industry. Engineering advances which incorporated automated equipment, non-corrosive construction materials, and improved ion exchange membranes allowed the electrodialysis process to compete in industrial waste treatment among other commercial markets. PROCESS AND APPARATUS DESCRIPTION The electrodialysis process utilizes direct electrical current passed across a stack of alternating cation and anion selective membranes in order to achieve an electrochemical separation of ionized materials in an aqueous solution. The membrane stack has the appearance of a plate and frame filter press and auxilliary equipment includes solution pumps, electrically actuated valves, filters, piping and a direct current power source. The ion separation membranes are thin sheets of synthetic cation or anion selective resins. Attaching sulfonate or quaternary ammonium groups to the cross linked copolymer structure determines the ion selectivity of the membrane. The membranes are separated from each other in the stack by non-conductive spacers that house flow channels which route the flow tortuously and parallel to the membranes. Direct electrical current passing perpendicularly to the membranes and solution passages attracts cations toward the cathode and anions toward the anode (Figure 1). As the ions from the feed stream pass through the ion selective membranes, they become concentrated in the adjacent brine channel and are retained there by the combined attractive force of the electrode and the repelling force of the next membrane toward the electrode. Limiting factors on the degree of demineralization possible include chemical solubilities in the brine flow and the current density that will produce an unacceptable degree of polarization (Figure 1). Feed or brine solution treatment with complexing agents or acids has been successfully applied to prevent membrane scaling. Polarization can occur when sufficient current density is applied to dissociate water in the ion depleted region of the diluting compartments near the membrane surfaces. Significant polarization is evidenced by large electrical resistances across cell pairs and notable pH differences between diluting and concentrating streams. Limiting current densities have been increased in U.S. manufactured equipment by utilizing tortuous flow paths of relatively high linear velocities thereby promoting continous solution mixing. Energy consumption is due to separating electrolytes and solutions, oxidation and reduction reactions occurring in electrode compartments, overcoming electrical resistance, conversion from AC to DC power, solution pumping and auxiliary equipment actuation. A major improvement to the basic electrodialysis process was applied in 1970 which resulted in frequent, automatic cleaning and descaling of membrane surfaces. The process, polarity reversal, incorporates alternating the cathode and anode on a periodic basis while exchanging product and brine flow channels via electrically actuated values. The reversal reduces the potential of stack plugging with CaCO3 (calcite), CaSO4 (gypsum), and colloidal materials and, in most waters, eliminates feed pre-treatment requirements. For approximately two minutes during and following the reversal, off spec. water is flushed to waste or reintroduced to the feed supply. The usual feed treatment on polarity reversing electro-

Jan 1, 1982

By A. F. Witt, A. M. Gaudin, A. K. Biswas

Finite contact angles in the rutile-water-organic liquid system are traceable to contamination or are due to addition of a surface-active agent. Finite contact angles are invariably accompanied by hysteresis.1-7 Besides surfactant concentration and pH, the nature of the organic liquid is found to be a factor influencing the magnitude of contact angle hysteresis. In a recent paper the authors have reviewed principles and applications of measurement methods for contact angles and their hysteresis.22 In this paper, these methods are applied to a system consisting of rutile, an organic liquid (benzene, decane, or dode-cane) and water. Surfactant (dodecylamine hydro-chloride) was used at various concentrations and various pH values. MATERIALS A synthetic rutile crystal supplied by the Linde Co. was used. It is a cylinder 1/2 in. diam, with faces cut perpendicular to the c-axis. The crystal is stated to be alumina-free and to be 99.9% pure. Rutile is a high surface energy solid, its calculated average field strength being 2.7 x 105 e.s.u.,9 its dielectric constant10 is 114. The zero point of charge of rutile was measured11 and found to be at pH 6.0. The atomic distances and bond angles of the tetragonal crystal of rutile have been precisely determined.l2 The organic liquids were specially purified. Reagent grade benzene was repeatedly shaken with concentrated sulfuric acid to remove thiophene, then neutralized with sodium hydroxide solution, rinsed with distilled water, dried overnight over anhydrous calcium chloride and filtered. The refractive index of this chemically purified benzene was 1.4977 (at 25°C) - very close to that of pure benzene (n25 1.4979).13 Both n-decane and n-dodecane were washed with aqueous sodium hydroxide, concentrated sulfuric acid (repeatedly, until the acid layer was colorless) and again with alkali, to free the organic hydrocarbon from fatty acids and unsaturated hydrocarbons. The organic phases were subsequently washed with distilled water and dried over anhydrous sodium sulfate. The filtered hydrocarbons were then distilled under vacuum (9-10 mm pressure). Decane, thus purified, showed traces of unsaturated and of carboxylic compounds. On gas chromatographic analysis the purified n-dodecane showed the presence of two impurities. However, the relative retention times of these components did not change substantially when measured on a polar or a nonpolar column. This indicates that the compounds were probably in the same polarity class, i.e. the components were nonpolar like dodecane. Conductivity water has always been one of the liquids. Conductivity of the water used was 10-6 ohm-' cm". Dodecyl ammonium chloride was prepared from pure amine (supplied by Armour and Co., Chicago), by Li in the MIT Mineral Engineering Laboratory.14 The critical micelle concentration at 25°C is known, 0.0138 mol per liter15 or 3.06 gpl. All our experiments have been done at concentrations lower than the critical micelle concentration. The glass vessels, glass drop holder and the rutile crystal were all cleaned with hot chromic acid followed by distilled water, concentrated hydrochloric acid, and again distilled water, and conductivity water. During the experiments, a nitrogen atmosphere was maintained. For this purpose, commercially purified nitrogen was further purified by passing it over hot copper wire at 450°C, then through columns of acidic chromous chloride solution, concentrated alkali solution and distilled water. APPARATUS AND METHODS Hysteresis was produced by the "captive drop" or constant volume drop method as well as by the "expanding-contracting drop" or variable volume drop method. The image of the drop while it is expanding, contracting or moving is projected on a screen and photographed. The developed film is projected through an enlarger and the contact angles measured with a protractor.

Jan 1, 1964

By Rex B. McLellan, W. A. Oates, William W. Dunn

Vapor transport experiments have been carried out in order to determine the saturation solubility of carbon in cobalt and nickel with respect to graphite over a large temperature range. Some of the uncertainty existing in the thermodynamics of these systems has been removed and accurate estimates of the heat and entropy of solution of carbon in nickel and cobalt have been deduced. The relatitle partial entropies of carbon are considered to be predominantly vibrational in origin. ALTHOUGH the thermodynamic properties of solid solutions of carbon in cobalt and in nickel have been investigated previously, the results of these investigations show a marked lack of agreement amongst themselves. In this investigation simple vapor transport experiments have been undertaken in order to measure the temperature variation of the saturation solubility of carbon in nickel and cobalt with the object of removing to some degree the uncertainties in the thermodynamics of these systems. In the case of the C-Co system, early measurements of the saturation solubility of graphite in Co show results at the same temperature differing by almost an order of magnitude.1-5 Recently Schenck, Frohberg, and Jaspert6 measured the equilibrium between CH4-H2 mixtures and C-Co solid solutions at five temperatures ranging from 850° to 1050°C. Their values of the activity of carbon in the solid solution, deduced from a knowledge of the chemical potential of carbon atoms in the gas, varies linearly with composition at each temperature and the authors concluded that the solutions were Henryan. The saturation solubilities deduced from Schenck, Frohberg, and Jaspert's measurements are in good agreement with the solubility determined at 1000°C by Rao and Nicholson7 and the value at 1000°C deduced from the measurements of smith8 on the equilibrium between CO/CO2 mixtures and C-Co solutions. The object of this investigation was to check the results of Schenck, Frohberg, and Jaspert and also to extend the range of solubility data to higher temperatures. In the case of the C-Ni system, there is fairly good agreement between the values given by schaefer9 for the saturation solubility of carbon C, in nickel, the value given at 1000°C by Rao and Nicholson,7 and that deduced from Smith's8 measurements of the equilibrium between C-Ni solutions and CO/CO2 mixtures at 1000°C. The values of C, deduced from Schenck, Frohberg, and Jaspert's6 measurements of the carbon activity in nickel are also in fairly good agreement. However, there is a large discrepancy between the above set of measurements and those of Lander, Kern, and Beach," who measured the carbon solubility of nickel in equilibrium with graphite by depositing an excess of graphite on the surface of Ni-foils from a gaseous mixture and subsequently diffusing in the carbon. These results are considerably higher than those mentioned above. The determinations6 of carbon activity a, in nickel from the CH4-H2 equilibrium showed that at all the temperatures investigated, the ac-values varied linearly with concentration up to about a, = 0.6 and then began to increase with concentration much more rapidly. On the basis of auxiliary experiments in which C-Ni solutions were equilibrated with graphite, Schenck, Frohberg, and Jaspert concluded that their CH4-H2 solid equilibrations at high values of a, were spurious and a, behaved linearly with composition up to the saturation limit (a, = 1). The short linear extrapolations of Schenck, Frohberg, and Jaspert's a, data yield values of C, in good agreement with those of Lander, Kern, and Beach." The solubility data for nickel discussed here is presented in Fig. 1 in the form of plots of ln[Cc/(l - 2cc)] vs 1/T. The discrepancies mentioned are clearly seen. In this investigation a vapor transport method is used to measure C, over as wide a temperature range

Jan 1, 1969

By T. B. Counselman

AfteR several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By T. B. Counselman

AfteR several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By L. C. Uren

Field studies and laboratory research have established the fact that the expulsive force which drives petroleum into wells, from the reservoir sands in which it is stored by nature, is primarly an expression of the energy latent within compressed natural gas dissolved or occluded in, or otherwise associated with the oil. Each barrel of oil produced is forced into the recovery well by the expansive energy of a certain volume of compressed gas, originally stored with the oil in the pores of the reservoir rock; and each cubic foot of gas so produced with the oil and expanded to atmospheric pressure reduces by so much the total natural energy available for oil expulsion. This relationship between the volumes of gas and oil produced has seemed so important that petroleum production technolo-gists have come to regard the "gas-oil ratio," or the "gas factor" as it has been more conveniently termed, as a measure of oil-production efficiency. Different methods of oil recovery and production devices are now Com pared on this basis and estimates of ultimate recovery obtainable through their use are considered by many to be inversely proportional to the values of their respective gas factors. The writer has been among those who have given support to a widcspread movement toward a proper recognition of the significance of the gas factor as a guide in the control of producing oil wells, and does not wish to oppose its more extended application. It seems necessary, how-cvcr, in view of the almost elemental faith with which the principle of the gas factor has been received in many quarters, to point out that it is a most complex factor, and one which cannot be regarded as an absolute index of production efficiency without due regard to other contributing factors by which it is influenced to an important degree. Variables Influencing Gas Factor The mere recording of a low gas factor, obtained through the use of some method or device, does not necessarily imply efficient oil production; and conversely, a high gas factor does not always signify inefficient recov-

Jan 1, 1928

By Harry Klemic

Zirconium and hafnium minerals are used industrially both as minerals valuable for their chemical and physical characteristics and as ores of zirconium and hafnium. The principal zirconium-hafnium-bearing minerals, their composition, and their ranges in content of zirconium and hafnium dioxides are listed in Table 1. The supply of zirconium and hafnium is based almost entirely upon the supply of the minerals zircon and baddeleyite. Eudialyte may eventually also be of importance as a source of these elements. Zircon, which generally contains nearly 49% zirconium and between 0.4 and 1.5% hafnium, is the principal industrial mineral of this group. Baddeleyite, a commercially important but less abundant mineral, contains as much as 73% zirconium and 0.4 to 1.7% hafnium. Eudialyte has a wide range in content of these elements, but analyses of material from several localities indicate values of 6 to 11 % zirconium and 0.07 to 0.4% hafnium. Zircon is a mineral consisting principally of zirconium, silicon, and oxygen that crystallizes from magmas during the formation of igneous rocks. Zircon also occurs in veins and in metamorphic rocks. It is in the tetragonal crystal system. It commonly forms as small well-developed prisms having pyramidal terminations but also occurs as irregular-shaped grains. Zircon has a hardness of 7.5 on the Mohs' scale. Its specific gravity is commonly between 4.68 and 4.70 (Dana, 1932), but the specific gravity varies somewhat depending upon com- position and state of alteration. Zircon has no good cleavage directions and is brittle, breaking with a conchoidal fracture. Zircon of the composition ZrSiO, would contain 67.2% Zr02 and 32.8% SiO2. However, in addition to about 1 % of hafnium, minor amounts of thorium, uranium, rare earth elements, yttrium, calcium, magnesium, iron, aluminum, phosphorus, and hydrogen, and trace amounts of other elements are commonly present in the mineral (Frondel, 1957). Radiogenic lead and other daughter products from the radioactive decay of uranium and thorium also accrue in the mineral. Radiation damage to the structure of zircons that contain appreciable amounts of uranium and thorium may alter the internal structure of the crystals to

Jan 1, 1975

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptbility. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new comination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmision to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 6, 1950

By B. B. L. Seth, H. U. Ross

A generalized rate equation for the reduction of iron oxide was derived from which two particular equations were obtained: one for rate controlled by the transportation of gas, the other for rate controlled by the phase-boundary reaction. Pellets of pure ferric oxide having diameters of 8.5 to 17.5 mm and a density of 4.8 g per cm3 were prepared and reduced by hydrogen at 750° to 900°C. From the analysis of data obtairzed, it was observed that neither the phase-houndarv reaction nor the transportation of gas controlled entirely the rate of redziction. Rather, the mechanism of reduction can he divided into three stages. In the beginning, the process seems to depend predominantly on the surJrce reaction, hut after a layer of iron is formed the diffusion of gas becomes the controlling factor. Towards the end, however, the rate falls sharply due to a decrease in porosity. The times predicted by the generalized equation for a certain degree of reduction showed an excellent agreement with those obtained experinmentally for pellets of varying sizes. WIDE interest in iron oxide reduction has resulted in many valuable studies pertaining to thermody-namical properties, equilibrium diagrams, and chemical kinetics. Although the thermodynamical properties and equilibrium diagrams are now known with a fair degree of accuracy, the mechanism and rate-controlling step in the reduction of iron oxides presents a problem to research workers which is still unsolved. This is because the field of chemical kinetics is so highly complex. Besides the chemical reaction between oxide and reducing gas, several other processes are occurring simultaneously such as solid-state diffusion of iron through intermediate oxides (FeO and Fe3O4), the diffusion of reducing gas inwards and of product gas outwards, and the sintering of iron if reduction is carried out above the sintering temperature of iron. Furthermore, there is a large number of variables, including the nature and flow rate of the reducing gas, the chemical composition and physical properties of the ore, the temperature of reaction, particle size, and so forth, all of which can affect both the mechanism and the kinetics of reduction. Despite the controversy and diversity of opinion about the mechanism of iron oxide reduction, three main schools of thought have emerged. According to the first, the rate is controlled by the diffusion of gas through the boundary layer of stagnant gas; the second claims that the rate is proportional to the area of the metal-oxide interface, while the third believes the transportation of reducing gas from the main stream to the metal-oxide interface and of product gas from the metal-oxide interface to the main stream to be the rate-controlling step. 1) The boundary-layer theory is true mainly for packed beds where the flow of gas through the bed is important. For a single particle, the boundary layer may be prevented from being the rate-controlling step if a gas flow rate of reducing gas above the critical flow rate is used. 2) Several workers have reported a linear advance of the Fe/FeO interface which provides excellent support for the belief that reduction is controlled by the surface area. McKewanl has given formal shape to this concept with mathematical derivation and has shown it to be valid for reduction of several iron ores, hematite, and magnetite, both by H2 and H2, H2O, N2 mixtures. Some other investigators, however, do not find this theory to be entirely valid. Deviations have been observed2 and further confirmedS3 Hansen4 also agrees that deviations do occur, at least in the latter stages of reduction, while from the data of several investigators summarized by Themelis and Gauvin,5 it is clear that the theory is not always applicable and further that, when it is applicable, it does not hold in the final stages of reduction. 3) Among those who claim the transportation of gas to be the rate-controlling step are Udy and Lorig,6 Bogdandy and Janke,7 and Kawasaki el a1.8 The validity of the theory has also been acknowledged indirectly by other research workers who show that the sintering and recrystallization of iron cause a decrease in reduction rate, for it is only if the transportation of gas is important that this sintering has any bearing. However, the theory has been rejected by some because they have failed to obtain

Jan 1, 1965

By Norman Lamont

The evaluation of certain reser-voir properties, such as porosity and fluid saturation, from electrical well surveys has been widely accepted in petroleum engineering. Various investigators have established relationships between these properties and certain parameters which affect the response of the electrical log. Among these are the resistivities of the mud, its filtrate, and its filter cake. In 1949, Patnode1 established a relationship between the resistivities of the mud and filtrate. The well logging service companies have contributed relationships for the mud-mud cake resistivities2,3 These have been valuable since it was the practice to measure only resistivity of mud at the well site. During the mid-1940's the industry began drilling wells with oil-emulsion drilling fluids. These were conventional aqueous muds with a dispersed oil phase. Since 1950, oil-emulsion muds have been used on an increasing number of wells each year. However, the practice of measuring only the resistivity of the mud at the well site has continued, and the mud filtrate and mud cake resistivities have been determined by the above-mentioned relationships. Service companies are now equipped to measure all three resistivities at the well site. An investigation was conducted on the resistivities of oil-emulsion muds, mud filtrates, and mud cakes to determine if these values conformed to the relationships for aqueous muds. TYPES OF MUDS Fifty-one oil-emulsion mud samples were prepared in the laboratory following a standard manual' published by a leading mud company. The diesel oil in the samples varied from 5 to 50 per cent, the majority of the samples being in the 10 per cent region. The basic aqueous mud types which were converted to oil-emulsion muds were commercial clay and bentonite muds, low pH and high pH, caustic-quebracho treated muds, and lime treated muds. The emulsions were stabilized by dispersed solids, lignins, lignosulfo-nates, sodium carboxymethyl cellulose, or sulfonated petrolatum. It is worthy of note that after a quiescent period of two weeks at room temperature all samples, regardless of emulsifying agent, remained stable. The make-up water for the muds was from the laboratory tap. Resistivities were varied by the addition of table salt to the water. A range of mud resistivities from 0.44 to 3.9 ohm-m was obtained in this way. Twenty-three field muds were tested. These covered the same range of mud types as did laboratory muds. Oil provinces of the Gulf Coast, South Texas, West Texas, Oklahoma, Montana, and Canada were represented. MUD TEST PROCEDURE Each mud was tested for density, viscosity, pH, and filter loss by standard testing techniques. The resistivity measurements were obtained with a Schlumberger EMT meter. This meter required small volumes of sample, e.g., 2 mm. Filtrate was obtained from a Standard Baroid fil-ter press at the end of a 30-minute test. The filter cake from the same test was used for cake resistivity measurements. Mud, filtrate, and cake samples were heated to 100" F in a constant temperature water bath prior to measurement of resistivities. RESULTS The relation between mud resistivity (Rm) and mud filtrate resistivity (Rmf) is shown in Fig. 1. The solid line represents an average for the data. The equation of this line is Rmf =0.876 (Rm) 1.075 . . (1) Arbitrary limits, indicated by the dashed curves, have been set. The majority of the data falls within these limits, but some points do lie outside the limits. The approximate equation Rmt = 0.88 Rm , . . . . (2) will give satisfactory results within these limits. The data on mud cake resistivity Rmc is shown in Fig. 2. The solid line is an average for the data. The equation for the line is Rmc = 1.306 (Rm)0.88 The dashed lines are arbitrary limits on the data. Within these limits, Eq. 3 may be simplified to Rmc = 1.31 Rm . . . . (4) DISCUSSION The limiting curves in Figs. 1 and 2 represent maximum deviations of ±25 per cent. Thus the use of the average curves can introduce considerable error. There is no substitute for accurate measurements of mud, mud cake, and mud filtrate resistivities at the well site. The mud sample tested should be representative of the mud opposite the formation being logged. The average mud filtrate resistivity curve of Fig. 1 is reproduced in Fig. 3 with two curves which have been published for clay-base aqueous muds2,3. The latter curves were determined from average values of a large number of drilling fluids. The three curves have essentially the same slope and the differences between them are from 7 to 22 per cent. Comparison is made only to illustrate the possibility of error

Jan 1, 1958

By M. I. Sherman, J. D. H. Strickland

USE of a hydrometallurgical approach to the oxidation of sulfide ores and extraction of metals therefrom may have advantages over the more common smelting techniques when a low grade deposit is difficult to concentrate or the subsequent separation of metals, coexisting in the ore, is laborious by any known smelting operation. For economic reasons, the most promising oxidants are either atmospheric oxygen or electric power. The use of oxygen, or air under pressure, has recently been revised. Pyrrhotite has been converted to iron oxide and elementary sulfur' and a variety of sulfides have been treated by Forward and co-workers.2-4 Generally sulfate is the end form of the sulfur but with galena in an acid medium, elementary sulfur can be formed." For economic reasons chlorine and ferric iron salts are about the only possible alternatives to the atmosphere as oxidizing agents for base metal sulfides. If aqueous solutions of chlorine or ferric iron are employed, the reduction products can be oxidized electrolytically in situ and used again, thus acting as catalysts for electric power as oxidant. The use of ferric salts for this purpose is established hydrometallurgical practicea but, although chlorine gas has been employed in the dry state at an elevated temperature, its use in aqueous solution at or near room temperature has not found favor. The reaction of chlorine water with the soluble sulfide ion has been studied by several workers,7-9 and both sulfate and elemental sulfur are found as end products, the latter being favored by the presence of a low concentration of oxidant relative to that of sulfide in solutions of about pH 9 to 10. Of direct bearing on the work in hand are an early American patent" and a recent Austrian patent." The former advocates stirring powdered ore with an aqueous solution of ferric chloride chlorine oxides and chlorine. In the latter it is claimed that both metal and sulfur can be obtained by electrolysis, in a diaphragm cell, of a metal ore slurry in brine. Details in these patents are scant and no data or explanation is given for the mechanism of the reaction which, in the Austrian work, is attributed to the (unlikely) action of nascent chlorine at the anode surface. No mention is made of possible differences in behaviour between various ores. Apparatus A complication encountered when working with chlorine water is that a serious loss of chlorine occurs by gas partitioning unless an enclosed system is used and any air space in the apparatus is kept very small and constant. Arrangements were made, therefore, to take out samples for analysis without letting air into the system to replace the liquid removed. For convenience in studying a heterogeneous reaction the apparatus was so designed that a reproducible controlled stirring rate could be maintained and the ratio of surface area of ore to volume of solution was approximately constant throughout any experiment. The apparatus used is shown in Fig. 1. The ground ore was placed in the horizontal cylindrical vessel, A, of about 1 liter capacity, heated by a constant temperature circulating bath pumping water through the concentric jacket, B. By adding chro-mate to this water, an ultraviolet radiation filter effectively surrounded the reaction vessel, greatly reducing any possible photochemical decomposition of chlorine solutions. Stirring was effected by glass paddles, C, attached by an axle to a magnet which was rotated by another powerful Alnico magnet, D, outside the glass end, this magnet being itself rotated by an electric motor electronically controlled to constant speed. Speed could be varied from about 150 to 900 rpm and was measured and held to within 1 pct of a given value. The end of the reaction vessel remote from the stirring magnet was closed by another one-ended glass cylinder, E, connected by thin polyethylene bellows, F, clamped by screw clamps and watertight rubber gaskets to the main vessel. Through E, a glass electrode and calomel electrode projected into the solution and a hypodermic syringe pierced a small bung and allowed acid or alkaline to be added to maintain a constant pH. By pushing the fully extended bellows until the two cylinders touched, from 50 to 100 ml of solution could be forced out through a sintered disk into the three-way tap system, G, either to waste (for flushing purposes) or up into a 10 ml burette where the solution could subsequently be measured out for analysis. The ore samples were introduced at H, the tube being stoppered by a thermometer of —1 to +52ºC range, graduated to 0.1°C intervals. To prevent ore from being ground in the end bearings of the stirrer these bearings were pro-

Jan 1, 1958

By Y. C. Kim, S. L. Barua

Underground coal mine planning has traditionally focused on the mine design aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most US underground coal mines. With the enactment of the Clean Air Act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the Btu content of coal are equally important for boiler efficiency. Coal mine planning must incorporate coal quality control aspects as well as traditional safety and efficiency aspects. According to an article in Coal Age (March, 1982), nearly one-half of the US coal exported to Europe does not meet the contract specifications regarding ash, sulfur and Btu contents. Although one of the reasons cited for this problem was "inadequate sampling at the US ports," the more fundamental cause probably lies in the inadequate quality control of run-of-mine (ROM) coal at the source. To perform adequate quality control of ROM coal, mines need predicted short-term in-situ coal quality information. Such predictions are generally based on whatever available sampling information is around the mine workings. Unfortunately, the closest sampling information, in the form of diamond drill hole assays, is often several thousand feet away in most underground coal mines and is inadequate for short-term coal quality prediction purposes. This is because the diamond drill holes (DDH) were traditionally placed in the coal deposit during the mine development phase to determine coal seam continuity and overlying roof conditions. They were not placed for short- term mine planning. A study was undertaken by the University of Arizona for the Homer City Owners in Pennsylvania to show that there is a need for more closely spaced samples, if the short-term coal qualities are to be predicted with any "reasonable" degree of accuracy. Prior to this study, a short-term quality prediction model, STPM, had to be developed. This model uses not only DDH, but also other sample information obtainable during face development work to predict the qualities of in-situ coal that are available in the immediate future.

Jan 1, 1985