Search Documents

By Everett G. Trostel

AMERICAN industry in 1943 emerged from the construction phase into the production phase, and American military operations passed from preparation into full action in the many theaters of the global war. The increased pace of industrial and military operations has resulted in a tremendous demand for petroleum and its products.

Jan 1, 1944

By E. R. Kaiser

COAL research during 1942 was directed in an important degree toward the solution of problems of wartime importance. A wider selection of coals for carbonization to meet the increased demand for coke, and the improved utilization of lower-grade coals for boiler fuel were made possible by fundamental studies on cod and ash behavior that had been started several years ago. The coal industry's interest in the work of the various laboratories brightened significantly as results were demonstrated on smokeless combustion in stoves, on stokers without coke trees, and on pulverized firing of forge furnaces. Despite the limitations of priorities and scarcity of materials, the mineral industries building of the West Virginia University was completed and equipped with facilities for research on coal min

Jan 1, 1943

By Dozier Fircley

SOME nonmetallic minerals and their products, such as portland cement, common brick and hollow tile, sand, gravel, crushed rock, vitrified salt-glaze clay pipe, and the like, are a necessity in every community. They are mineral in nature but the establishment of plants for their production is usually a local and elementary problem. Yet it is probable that an economic study of the problem in every locality will show that such nonmetallic mineral commodities are not always obtained in the most economical way, or in the best quality. Other nonmetallic minerals are of such value that they may be shipped for long distances and sold in sufficient quantities to establish prosperous commercial ventures. Among these are phosphates, barium compounds, borates, nitrogen compounds, magnesium compounds, sulfur, asbestos, and potash. Success in marketing such products depends on quality, production cost, transportation, and similar conditions.

Jan 1, 1932

By HENRY M. PARKS

THE total production of all metals in Oregon to date is estimated at $160,000,000; ~115,000,000 from eastern Oregon and $45,000,000 from the western part of the state. In 1916 the metal production of the state was approximately $4,000,000, while the present annual production has dwindled to a little less than $1,000,000. Western Oregon The state of Oregon contains several metal-bearing areas, widely scattered in different regions. More than half of its coast is fringed with a belt of auriferous sands which sometimes are rich in fine gold. A second mining field, the chief producing one of western Oregon, is situated in the southwestern part of the, state and includes Jackson, Josephine, Douglas, Coos and Curry counties. It may be considered as the northern extension of the gold and copper belt of California. A third region in western Oregon is that on the western slope of the great Cascade range in the Bohemia, Blue River, Quartzville, North Santiam and Ogle Creek districts-from the Siskiyous on the south almost to the base of Mt. Hood near the Columbia River on the north.

Jan 1, 1925

By Edward Steidle

TWO years ago the Committee on Latin American Education Relations, Mineral Industries Education Division, started a study of mineral industries education in the Latin Americas. Information was obtainable only with great difficulty. Some information was available piecemeal but no complete resume had ever been assembled. Initial assistance was gained from the United States Office of Education and the Pan American Union. This, and first-hand knowledge of the writer, provided a list of colleges and universities which were believed to offer work lead. ing to a degree in one or more branches of the mineral industries. Detailed information could be obtained only by direct contact with each university through air mail service. Questionnaire letters were sent to officials of 34 colleges and universities. Twenty-one gracious replies were received. Fourteen of the colleges and universities concerned offer curricula in mining, five in metallurgy, three in petroleum, seven in geology, one in geographical engineering, one in topographical engineering, and one in geophysics. Two institutions offer advanced training in petroleum engineering. No institution offers any courses under the caption of ceramics or fuel technology.

Jan 1, 1945

By Herbert W. Graham

IRON ORE is widely distributed throughout the world. Ores sufficiently high in iron content to be practical for the operations of iron and steel making occur in so many places that it is only by the accident of political subdivisions that any given nation does not have adequate and suitable iron ore. Data prepared by various authorities show that in the Lake Superior region alone there are reserves of 1,200,000,000 tons of iron ore of an iron content and at the level of production cost to which the industry has been accus tomed. At an annual consumption of 80,000,000 tons these reserves will last fifteen years. Taken alone these figures would be alarming, but over a considerable period of years the total reserve tonnage has been more or less steadily increased by improvement and extension of mining and beneficiation methods. The rate of depletion of reserves has been only about one third of the rate of consumption. On this basis the cheap high-grade ores of Lake Superior would last 45 years.

Jan 1, 1947

By R. Adair, W. R. Hudspeth, W. T. McDaniel

D. C. Ralston (U. S. Bureau of Mines, Washington, D. C.)—Flake mica can be beneficiated by a wider variety of methods than almost any known mineral. However, most of these methods are not recorded. It is therefore a pleasure to find a written record of another application of a new method of beneficiation. The fact that the Humphries spiral gives a concentrate containing the mica flake mixed with the slime and small grit has forced a further separation by screening, in which the finest of the flake will pass through. Fine flake has its uses and if mixed with slimes or clay is recoverable reliably only by flotation. This loss must be charged against the spiral. On the other hand, the new muscovite mica paper recently brought out by General Electric Co., can be made only with grit free flake larger than 50 mesh. It is of interest to learn from the authors whether the washing of the flake on a 50 mesh screen can take the grit content below 1 pct, to meet this new demand. Must another degritting process be used on the flake, like electrostatic treatment of the dried material? H. D. Snedden (The Humphreys Investment Co., Denver)—When recovering mica in the spiral, gangue particles coarser than 16 mesh can be rejected more readily when operating at a high pulp density (35 pct solids) or a low volume rate (—15 gpm). A launder screen as used by Lehigh Coal Co. has proved very satisfactory to partially dewater the mica concentrate and to reject any gangue slimes it may contain. Under certain conditions mica cleaning in the spiral can be improved by reagentizing the spiral feed, the object being to insure wetting of the gangue minerals and to agglomerate or prevent wetting of the mica particles. R. B. Adair (authors' reply)—The grit content of the mica recovered on Humphreys Spirals varies with the fineness of the launder screen used to clean the mica product. Normal practice has been the use of 80 mesh screen, which will produce a mica product of acceptable grit content for most purposes. By using a 50 mesh screen, and increasing the screen area per ton of feed, it is felt by the authors that a mica of 99 pct plus purity could be obtained. This statement would hold only in the case of mica feed which was well de-laminated, and free from "clay balls," (semikaclinized feldspar), which tends to follow the mica through the process.

Jan 1, 1952

By A. C. Butterworth

M OST operators of open-pit mines in the Lake Superior iron ore district are quite familiar with the use of fuel oil in the heavy-duty Diesel engines commonly used in truck-haulage service but some operators, including my own company, Pickands Mather, have had butane-engine trucks in service for several years, and less is known of their operation. One of the first installations of trucks for iron-ore haulage was in 1939 at a deep open-pit mine on the Cuyuna Range. These superseded standard-gauge steam haulage. Trucks then obtainable were equipped with 150-hp Diesel engines, and the speed of these units on an 8 % grade would have been so slow, considering the depth of the pit, that plans for an all-truck haul out of the pit were rejected. About this time one of the engine manufacturers brought out an auto-

Jan 1, 1948

Discussion of the papers of Benjamin Talbot. E. A. Beck, Emil Gathmann, Sir Robert A. Hadfield, and P. H. Dudley, presented at the New York Meeting, February, 1913, and printed in this Bulletin (No. 76, April, 1913). CHAIRMAN JAMES F. KEMP :-I call upon Prof. Albert Sauveur to open the general discussion on the subject of sound steel ingots. ALBERT SAUVEUR, Cambridge, Mass. :-I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain some very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my Views.

Jan 4, 1913

By H. L. Teichman, E. M. Sipprelle

ENACTMENT' of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming. The oil shales of western Colorado are apparently richer, more accessible, and more amenable to exploitation than elsewhere in the Rocky Mountain region. The site chosen for the Bureau's Experimental mine is about 10 miles west of Rifle in northwestern Colorado. It is within a 1000-sq-mile area from which, it has been estimated, 300 billion barrels of shale oil could be produced from a 500-ft measure near the top of the formation. One hundred billion barrels of this amount could be produced from the Mahogany ledge, a 60 to 100-ft section near the bottom of the 500-ft measure. This ledge is considered to have economic importance at present. The Green River formation was laid down as sediment in the bottom of vast, shallow inland lakes during Eocene time. The deposit is flat-lying, and there are no faults, fissures, or local rolls. Oil shale is actually a strong, tough magnesium marlstone, which will stand unsupported over relatively wide spans. These and other natural physical characteristics favor mechanized, low-cost mining, which is essential for establishment of an oil-shale industry. It was realized from the outset that an extensive research program would be necessary to develop mining methods, equipment, and techniques for a mechanized, low-cost operation. The program was designed to include research. into all the productive phases of mining, such as drilling, blasting, loading, transportation, and maintenance of the mine structure. The methods, equipment, and techniques developed as a result of this research have established a production of 116 tons per man-shift total labor at a direct cost of $0,292 per ton. Another important phase of the research program that has received little publicity because of its theoretical nature is study of the roofstone behavior and determination of mine structure stresses. This paper purposes to discuss this phase of the research program. Preliminary studies of the physical properties of the Green River oil-shale formation were made in the Barodyramics Laboratory at Columbia University during the latter part of 1945 and the early part of 1946.* The purpose of these studies was to determine the maximum size of unsupported underground openings that would be commensurate with safety and still permit the use of large, efficient mining equipment. Also to be determined were the pillar support to extraction ratio and the shape, size, and spacing of supporting pillars. Selected samples of possible roofstones near the top of the Mahogany ledge, as well as representative samples of different rock types found within the ledge, were obtained from the Bureau's oil-shale mine for these studies. The maximum safe unsupported roof span calculated from this work was 200 ft. Using a safety factor of four, it was theoretically determined that openings 60 ft wide could be advanced under a roofstone at the top of the Mahogany ledge. To support the overburden, 60-ft-sq pillars would be left in a checkerboard pattern. From visual observations made of core samples through the selected roofstone at the oil-shale mine, it was determined that the roofstone was actually a plate 6 to 8 ft thick. Because the calculations were theoretical and allowance had to be made for unknown cracks and fractures in the formation, openings 50 ft wide and pillars 60 ft sq were originally contemplated in the Bureau's Experimental mine. This would be the minimum allowable width that would permit use of large underground mining equipment. For lower mining costs and greater efficiency larger openings were desirable. Different but analogous approaches were made to the problem at the Bureau of Mines Applied Physics

Jan 1, 1951

By H. L. Teichman, E. M. Sipprelle

ENACTMENT' of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming. The oil shales of western Colorado are apparently richer, more accessible, and more amenable to exploitation than elsewhere in the Rocky Mountain region. The site chosen for the Bureau's Experimental mine is about 10 miles west of Rifle in northwestern Colorado. It is within a 1000-sq-mile area from which, it has been estimated, 300 billion barrels of shale oil could be produced from a 500-ft measure near the top of the formation. One hundred billion barrels of this amount could be produced from the Mahogany ledge, a 60 to 100-ft section near the bottom of the 500-ft measure. This ledge is considered to have economic importance at present. The Green River formation was laid down as sediment in the bottom of vast, shallow inland lakes during Eocene time. The deposit is flat-lying, and there are no faults, fissures, or local rolls. Oil shale is actually a strong, tough magnesium marlstone, which will stand unsupported over relatively wide spans. These and other natural physical characteristics favor mechanized, low-cost mining, which is essential for establishment of an oil-shale industry. It was realized from the outset that an extensive research program would be necessary to develop mining methods, equipment, and techniques for a mechanized, low-cost operation. The program was designed to include research. into all the productive phases of mining, such as drilling, blasting, loading, transportation, and maintenance of the mine structure. The methods, equipment, and techniques developed as a result of this research have established a production of 116 tons per man-shift total labor at a direct cost of $0,292 per ton. Another important phase of the research program that has received little publicity because of its theoretical nature is study of the roofstone behavior and determination of mine structure stresses. This paper purposes to discuss this phase of the research program. Preliminary studies of the physical properties of the Green River oil-shale formation were made in the Barodyramics Laboratory at Columbia University during the latter part of 1945 and the early part of 1946.* The purpose of these studies was to determine the maximum size of unsupported underground openings that would be commensurate with safety and still permit the use of large, efficient mining equipment. Also to be determined were the pillar support to extraction ratio and the shape, size, and spacing of supporting pillars. Selected samples of possible roofstones near the top of the Mahogany ledge, as well as representative samples of different rock types found within the ledge, were obtained from the Bureau's oil-shale mine for these studies. The maximum safe unsupported roof span calculated from this work was 200 ft. Using a safety factor of four, it was theoretically determined that openings 60 ft wide could be advanced under a roofstone at the top of the Mahogany ledge. To support the overburden, 60-ft-sq pillars would be left in a checkerboard pattern. From visual observations made of core samples through the selected roofstone at the oil-shale mine, it was determined that the roofstone was actually a plate 6 to 8 ft thick. Because the calculations were theoretical and allowance had to be made for unknown cracks and fractures in the formation, openings 50 ft wide and pillars 60 ft sq were originally contemplated in the Bureau's Experimental mine. This would be the minimum allowable width that would permit use of large underground mining equipment. For lower mining costs and greater efficiency larger openings were desirable. Different but analogous approaches were made to the problem at the Bureau of Mines Applied Physics

Jan 1, 1951

Meeting of May 22, 1914.-President Thayer. announced the appointment of the following Committee on Arrangements for the San Francisco meeting of 1915: Charles W. Merrill, Chairman; F. W. Bradley, Abbot A. Hanks, S. B. Christy, and H. C. Hoover. President Thayer announced the appointment of the following Committee on Organization for the Utah-Nevada Local Section: R. C. Gemmell, Chairman; C. D. Blood, Lafayette Hanchett, Ernest Gayford; Duncan MacVichie, and George W. Riter. The President of the Institute offered $100, to be known as the "President's Prize," to be used as prizes for the best papers submitted by members of the Affiliated Student Societies, to be divided as follows: First Prize, $50; Second Prize, $30; Third Prize, $20. A committee, consisting of J. F. Kemp, Chairman; W. L. Saunders, and T. T. Read, was appointed to report on the conditions to govern the award. The President announced the appointment of the Committee on Mining and Milling Methods, the personnel of which is shown on a subsequent page of this Bulletin. The following were appointed on the Advisory Committee to the U. S. Bureau of Standards, to represent the manufacture of the various non-ferrous metals as indicated: Copper, F. L. Antisell; Nickel, David H. Browne; Lead, H. O. Hofman; Aluminum, J. W. Richards; Zinc, G. C. Stone. It was voted to hold a meeting of the Institute under the auspices of, the Iron and Steel Committee, the Committee on Petroleum and Gas, and the Committee on Coal and Coke, in Pittsburg, Pa., Oct. 8, 9, and. 10, 1914.

Jan 7, 1914

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A. Vogel, William H. Blauvelt, William Kelly, Leonard. Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster. Henry M. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson, It will be noted that the various interests of the iron and steel industry are authoritatively represented on this Committee by producers of raw materials (iron ore, coke, and other fuels, refractories, etc.) and of finished materials, by consumers, consulting metallurgists, and educators. The primary duties of the Committee are to secure important papers on iron and steel, to promote their discussion, to organize lively and fruitful meetings, and otherwise to foster the interests of the large number of members of the Institute connected with the iron and steel industry in its many phases. Its success during the past year has been noteworthy. Through its instrumentality many valuable papers were presented at the Cleveland and New York meetings, followed by animated and productive discussions, while the attendance of iron and steel men at both meetings was remarkably large and representative.

Jan 5, 1913

J. E. JOHNSON, JR., New York.-It seems to me that it ought to be somebody's job to tie these notch tests with the reversed-stress tests, because the thing that causes failures in structures, in a great majority of cases, is where the material is stressed repeatedly up somewhere near the elastic limit, and the repetition of that stress seems to bring about what I suppose you may call a growth of crystals and that eventually develops into a break. It seems to me that it would be of the greatest value if there could be a coordination of the results of a shock test of some kind with the reversed-stress test, so that we could be sure that a material that had shock-test resistance would have reversed-stress resistance. H. F. MOORE,* Urbana, Ill.-The question raised by the speaker concerning the correlation of results from impact tests of notched bars with the results of repeated-stress tests is a very complicated one. Impact on a specimen sends energy into the specimen, and if the specimen absorbs this energy without fracturing there must be developed both stress and elongation. A notch in the specimen allows but little elongation to take place before rupture, and develops the ductility of the

Jan 5, 1919

L. S. PANYITY.-I made inquiries from the Smith and Dunn people, who are the originators of the compressed air and gas method of increasing the production of oil wells, as to how much pressure the sand will stand; that is, relative to the original rock pressure. They tell me that they have not been able to show, up to date, any pressure in a sand greater than the original pressure. I have also made 'a statement to that effect, but I am really dubious as to whether that is right, as I am not sure that you cannot get a greater pressure. However, I think that a greater pressure would be dangerous because it might cause a loss of gas. C. H. SHAW, ? Lawton, Okla.-In regard to the gas that was put into the pool up in New York State, may it not be possible that, on account of errors, etc., in measuring or computing, there is a mistake in the apparent fact that more gas was gotten out than was put in? L. S. PANYITY.-Unfortunately, I have not the papers I expected from those people to show the actual conditions, but I do not doubt that such

Jan 4, 1919

By R. Maddin, C. H. Mathewson, W. R. Hibbard

Recent publicationsl.2 establishing the presence of cross-slip in strained metallic single crystals oriented wholly within the area of single slip as predicted from the generalizations of Taylor and Elam3 described these markings as they appeared during the initial stages of the deformation process. At that time, the plane having a common glide direction with the primary slipping plane was reported as the cross-slip plane although the specific direction was not confirmed. Consequently, in continuation of the research, it seemed advisable to investigate the micro-graphic appearance of cross-slip together with the Laue back-reflection X ray analysis and stress-strain data during the later stages of the deformation process. Accordingly, a single crystal of brass (72.75 pct Cu, 0.01 pct Fe, 0.01 pct Pb, 27.23 pct Zn) was polished mechanically and repolished electrolytically after the manner described in the earlier paper.' Three pairs of flat surfaces, parallel to the specimen axis, and (1) perpendicular to the plane containing the pole of the primary glide plane and the specimen axis, (2) perpendicular to the plane containing the pole of the cross-slip plane and the specimen axis, and (3) perpendicular to the plane containing the slip direction and the specimen axis, were polished mechanically and repolished electrolytically, resulting in a final minimum gauge diameter of 0.4864 in. in a gauge length of 3.36 in. The specimen was elongated in tension and load-extension readings were taken following the method described in the initial investigation.' Observed reorientations were obtained from a series of Laue back-reflection photograms at the center and ends of the gauge length and at various positions around the circumference of the specimen. These were interpreted after the manner of A. B. Greninger.4 Cross-slip (Fig 1 and 2) was found with the first appearance of the primary slip clusters and usually joined members of these clusters. In addition, a third set of entirely different markings (Fig 3) could be noted. The displacement of this third set by the primary slip lines was measured as 8300 at. diam (3.04 microns). Since the specimen was carefully observed at high magnifications before any deformation and no markings of any type could be noted, it would appear that this third set was formed during the deformation process prior to the initiation of classical primary slip. Additional extensions produced no unusual change in the appearance of either cross-slip or the third set of markings. The number of lines increased with increasing elongation and appeared, generally, in areas where earlier markings were present. The continuity of the clusters of cross-slip lines in Fig 4, 5 and 6 illustrates that they are neither noticeably displaced by nor do they displace the primary lines at this stage. In Fig 7, cross-slip appears in a long narrow localized band approximately 45 degrees from the stress axis. This somewhat resembles a twin band except for the lack of a sharp boundary. After a shear of 0.257, suffcient additional glide occurred on the cross-slip plane to displace the primary slip lines (Fig 8). Generally, where a large number of cross-slip lines could be observed in an area on one flat surface, few cross-slip lines appeared on the diametrically opposite position on the parallel flat (Fig 9). These, of course, were not matched observations on the same glide ellipses. It was extremely difficult to make such comparisons. The third set of markings (Fig 10) was extensively displaced by glide on the primary slip planes. A plot of the width of primary slip clusters versus their displacement of the third set of lines is shown in Fig 11. The slope and the linearity of the plot suggest that each primary glide plane slips to a constant maximum value of shear before further slip is transferred to another plane. A shear value of 0.28 was determined in this case. Heidenreich5 has presented a similar schematic representation of glide for aluminum. After the specimen had attained an elongation of 51.8 pct, corresponding to a shear of 0.973, cross-slip appeared very prominently in certain areas as shown in Fig 12, yet at diametrically opposite positions very little cross-slip could be noted, Fig 13. Classical conjugate slip was found at this advanced stage in the deformation, Fig 14, which corresponds to the axial location shown at 12 in Fig 15. It should be noted that cross-slip occurs within the conjugate slip clusters and on the same plane as the cross-slip associated with the closely spaced primary lines which constitute a background in less distinct focus. The third set of markings noted at all stages in the deformation of the

Jan 1, 1950

“IT is decreed by Divine Providence that those who know what they ought to do and then take care to do it properly, for the most part meet ' with good fortune in all. they, undertake; on the other hand, misfortune overtakes the indolent and those who are careless in their work." These are the words of Georgius Agricola. to. those who are engaged in mining, taken from De Re Metallica, Book II, second paragraph. Safety in mining is just that simple, when considered on the basis of the individual. The words imply a .knowledge of what is to be done and how to do it. Armed with this knowledge it is only necessary to proceed with diligence and care to achieve the desired end without personal or financial mishap. Obviously the complication arises in the large company operating numerous mines and the consequent ramifications of company structure embodying management, supervision, engineering, and labor. Agricola stresses later on the importance of supervision and direction by the owners of the mine. We know that this principle is recognized today by the frequency with which the statement is repeated "a safety program must stem from management." People charged with responsibility for safety and management also stress the importance of securing the cooperation of the employees in formulating and carrying . out safe working practices. Safety committees consisting of employees, supervisors, and. representatives of management are recognized as the most practical method of achieving safety consciousness in all levels of mining company organization.

Jan 1, 1952

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By R. S. Cartwright

TWO types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent on the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination—the combination which when engaged will suspend the least amount of weight—has a value of 1.00. According to the table there are "blind spots" in the series. This is true particularly among the lowest ratios, which are most used to suspend the major part of the weight when great depths are reached. It will be noted that there is a difference of nearly three units in the value of the

Jan 1, 1929

By S. A. Wookey

More than 90 per cent of the ore produced by stoping at McIntyre is mined by horizontal cut-and-fill methods. The remainder is mined by square set and fill. In the stopes on the upper levels, mill holes are spaced 80 ft. apart and usually it is feasible to mine the breast for the full distance between the mill holes in one operation and to break, clean out and fill without any support for the roof or walls, other than the odd crown bar or sprag. The ore is scraped to the mill holes by small (10 to 15 hp.) air-operated slusher hoists. No grizzlies are used over the chutes and care is taken to break up the big pieces beforehand. Fill usually is spread by tramming sand or waste in a one-ton car from the fill raise. Fill raises are driven parallel to the strike of the vein and are inclined at approximately 48°. In long stopes, where more than one fill raise is necessary, they are spaced about 300 ft. apart. It is sometimes necessary to stand square sets for a short distance each way under the brow of the fill raise. support needed increases and on the lower levels and in some wide stopes where closer support of the back is necessary, it has become standard practice to timber the stope with 12 by 12-in. timber. Rough timber sets consisting. of caps, tightly blocked to the back and supported on posts 7 ft. high, are placed at about 5 ft. intervals. These sets are generally salvaged from the lower breast before blasting and are used again on the upper slice after the fill has been placed. In general, two or three breasts may be broken down before mucking out and filling and the ground stands long enough to enable this to be done safely. On the lower levels and in certain wide stopes and in heavy ground, a more intermittent method must be used. Only one breast or even part of a breast can be blasted and the back must be timbered before the ore can be removed. In these cases, sill timbers 16 ft. long, supported at one end on posts from the fill and at the other end on pins inserted in holes drilled in the face, are used. Timber cribs 5 by 9 ft. built from the fill to the roof and tightly blocked to the back are used throughout the mine to reinforce both the timber sets and the square sets.

Jan 1, 1946