Search Documents

By D. J. Jr. McAdam

RESULTS of a general survey of corrosion-fatigue phenomena at the Naval Engineering Experiment Station were presented in five previous papers.1-5 In these papers references were given to the work of Haigh in 1917.6 The five papers mentioned gave a general survey of the behavior of metals when tested to failure under simultaneous corrosion and cyclic stress. As a result of this survey the fourth paper gave a tentative analysis of the corrosion-fatigue process. According to this analysis, if the initial stress is below the endurance limit but above the corrosion-fatigue limit, the corrosion-fatigue process is divided into two periods. The first period is the formation of pits. As the initial stress is below the endurance limit, the pitting is assumed to be due to corrosion, not to fatigue. The corrosion pitting, however, is not the ordinary pitting of stressless corrosion, but is an accelerated pitting due to the effect of the cyclic stress on the corrosion. As the pit progresses, both the actual stress and the effective solution pressure increase. The increase of actual stress is due to increasing stress concentration at the bottoms of the pits. The increase of effective solution pressure is due to the increase of actual stress. The mutual intensification of stress and solution pressure continues until the actual stress at the bottoms of the pits surpasses the endurance limit. The second period of corrosion-fatigue then begins. In this period the process is merely fatigue accelerated by the corrosion. The cracks advance at a continually accelerated rate until the specimen breaks.

Jan 1, 1930

Jan 1, 1952

By C. O. Swanson

In the iron ranges of northern Michigan, magnetic data have been used as an aid in geologic field work since the time of the earliest surveys. The presence of complex structures containing magnetic formations, and the general scarcity of exposures, guided the early work into this line of attack, and later field studies tended to place more and more emphasis upon this geophysical relationship, until, at present, the collection of magnetic data is a matter of routine in any areal survey. At first, horizontal deflections of the compass needle were the only data collected. In subsequent surveys, greater dependence was placed on dip-needle readings, which record variations in the intensity and inclination of the earth's magnetic field. Recently the trend has been toward adjusting the instrument so as to reduce the influence of changes in inclination, and using a more sensitive modification, called the Superdip,' in weakly magnetic areas. To a minor extent, the magnetometer has also been employed. The object of this paper is to present the writer's experience with magnetic data in this region. The conclusions are based on work covering a period of 10 years, and spread over nearly all of the iron ranges and a large part of the intervening areas. The viewpoints expressed are purely geological ones. In other words, any opinion as to the usefulness of a certain relationship is based upon the writer's experience with it as a guide in interpreting the structures of this region, and not upon its soundness theoretically, nor its usefulness under other conditions. A very brief summary of the conclusions is as follows. The most important step is that of collecting the magnetic data. This requires a suitable adjustment of the dip needle, and sufficient readings to accurately portray the variations in the magnetic field, which are apt to be irregular. Once the readings are taken and plotted in some clear fashion, the interpretation of them is usually merely a matter of observing their relation-

Jan 1, 1934

By N. F. Mott

Jan 1, 1961

By William Waters Van Ness

The Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively reccnt date, were carried out in the neighborhood of the village of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E—W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposcd to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Jan 1, 1909

By S. Norton

GEORGE C. FOOTS, Port Henry, N. Y. (written discussion).-The paper by Mr. Norton and Mr. LeFevre will bear the most careful consideration by all interested in the iron business, particularly in the East. There is much information contained therein which should be emphasized. The idea of handling iron-bearing rock in quantities comparable to the porphyry coppers does seem at first blush to be beyond the pale of commercial possibility. Yet, today in the Adirondack region 25 per cent.

Jan 4, 1917

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

[IRVING, JOHN D. :-(Continued.) Some Features of Replacement Ore-Bodies, and the Criteria by Means of Which They May be Discovered, XLII, [xlvii]. Discussions: on A Concise Method of Showing Ore-Reserves, XLIII, 714; on The Iron Deposits of Daiquiri, Cuba, LIII, 65; I on Recrystallization of Limestone at Igneous Contacts, XLVIII, 214; I on To What Extent is Chalcocite a Primary, and to what Extent a Secondary, Mineral in Ore Deposits, XLVIII, 194. minerals of gold deposits, Homestake belt, Black Hills, S. D., XLII, 54.]

Jan 1, 1918

By M. C. Lavine, H. C. Gatos, R. S. Mroczkowski

The structure of GaAs-Ge heterojunctions prepared by a back-melting process was studied by X-rav diffraction, melallographic, and electron-micro-analyzer techniques. The boundary region between the GaAs and the germanium was found to consist of a four-layered band. A discontinuity between the two inner bands was brought about by solidification occurring simultaneously from the GaAs and the germanium side. The junction material OH either side of the central discotinuity was found to have grown as a single Crystal with the orientation of the parent substrate. It was found essential to determine the GaAs-Ge phase diagram. This was accomplished by a series of alloys containing 0 to 40 wt pet GaAs. Over this range the diagram is a simple eutectic with the eutectic point at 74 wt pet Ge and 845 C. The limiting- solubility of Coils in germanium was found to bc less than 5 wt pet. The Kossel divergent-beam X-ray technique was used to study orientation relationships across the boundary lager. A great deal of effort has been recently expended on the electrical properties of heterojunctions. Little attention, however, has been given to the metallurgical variables which may be of importance in the formation of the junctions. The present work was undertaken to investigate some of the more pertinent metallurgical aspects of interface-alloyed GaAs-Ge heterojunctions. Such parameters as solidification processes, composition gradients, orientation effects, and the accommodation of crystal structures have been the objects of study in this program. EXPERIMENTAL PROCEDURES Phase Diagram. The phase diagram of the GaAs-Ge pseudobinary system was determined by means of cooling curves. A Bridgeman furnace was employed with the center section maintained at 1200°C and the upper section at 800°C. Melts varying from 0 to 40 at. pct in GaAs content were used. Each charge was incapsulated under a two-thirds atmosphere of argon in a carbon-coated quartz tube. Five min in the furnace hot zone provided rapid melting and homogenization. The capsule was then removed to the cooler portion of the furnace. Cooling times were of the order of 3 min. The resulting homogeneous microstructure indicated that equilibrium conditions were obtained by this procedure. Formation of Heterojunctions. Rectangular parallelepiped single-crystal samples were cut with the large faces of either the (l00), (110), or (111) orientation. The remaining four surfaces were also cut to specific orientations to permit accurate relative orientation of the GaAs-Ge pairs. The

Jan 1, 1965

By C. E. Reistle

All crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms. Factors That Control the Solubility of Paraffin in Crude Oil Two main factors, possibly three, govern the solubility of wax in crude oil. The first of these is temperature. The solubility of wax in crude oil increases with an increase in temperature, and as the temperature approaches the melting point, the wax becomes soluble in all proportions in the crude oil. The higher the melting point of a wax, the less soluble it is in crude oil below its melting point. All crude oils containing wax can be chilled to a point where the oil is saturated with wax. If the temperature is decreased below this point, some of the wax will crystallize from solution. Fig. 1 shows the effect of temperature on the solubility of crude paraffin in oil. The second factor is the amount of volatile constituents and gas removed from the crude oil. Evaporation of the volatile constituents and gas lessens the volume of the oil and concentrates the solution of wax in the oil; therefore less wax can be held in solution at a definite temperature. As the natural amount of wax present in the oil is constant, this results in the oil becoming saturated with wax at a higher temperature than if the volatile constituents and gas were still in the oil. As an example of this, a fresh sample of crude oil having a gravity of 39.8

Jan 1, 1928

By J. A. Kitchener, J. P. Anfruns

Measurements have been made of the rate of capture of single particles of strongly hydrophobic, surface-methylated, quartz, of sizes ranging from 12 to 40 µm diam., by single rising bubbles of diam. 0.5 to 1.1mm. The results agree closely with the theoretically calculated hydrodynamic collision rates, indicating that, in this system, every collision results in capture and retention of a particle.

Jan 1, 1976

By C. E. Jr. Reistle

ALL crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms.

Jan 1, 1927

By T. A. Rickard

The earlier paper (Trans., xx., 463) describing this Victorian mining district, to which the present is supplementary, was mainly confined to the consideration of the "saddle-reefs," as scientifically the most interesting and economically the most important of the

Jan 1, 1893

By D. B. Rushmore, K. A. Pauly

Of primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must have careful consideration. While a general discussion of the subject of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity or the hoist, and the latter thus becomes of the first importance.

Jan 1, 1911

By J. B. Goddard

Crystallization of ammonium paratungstate (APT) is frequently the last effective purification step in producing high-purity tungsten. However, crystallizer mother liquors are often several times higher in tungsten than predicted by the solubility of APT. The formation of heteropoly anions, particularly those containing phosphorus and silicon, is largely responsible. Solubility of tungsten in APT mother liquor can be linearly correlated with the concentration of these and other impurities. The problem can be overcome by direct treatment of the crystallizer feed solution with aluminum sulfate. By appropriate treatment, the aluminum hydroxide flocculates and is easily filtered, resulting in a purified low-aluminum crystallizer feed from which high APT yields can be attained.

Jan 1, 1985

By William R. Webster

This is a subject which our Institute has made peculiarly its own. In the first volume of its Transactions the analysis of steel received attention, and every subsequent volume has borne witness to the acuteness and industry of our members in the investigation of this subject. The keynote mas struck, in this as in so many other lines of progress, by A. L. Holley, in his paper on " Tests of Steel," read at the Easton meeting of October, 1873 (Trans., ii., 116)—an essay which may rank as a classic by reason of .its elegant form, logical force, and clear prevision of all the bearings of its theme, Taken together with the brief report of the discussion which followed it (in which Dr. Drown emphasized the effects of heat-treatment and mechanical handling, and Dr. Sterry Hunt the importance of minute variations in chemical composition, and of possible isomeric and allotropic conditions), it constitutes, after the lapse of twenty-five years, an admirable and adequate introduction to the long list of technical papers which have succeeded it. Three years later came the epoch-making papers of Dr. C. B. Dudley on the relation between the chemical composition and physical properties of steel rails, which, with the voluminous discussion they evoked, constitute a special volume, published by the Institute, and full of useful suggestions. If Dr. Dudley could be induced to resume this investigation, he would doubtless be able to solve many points still uncertain or disputed. But I cannot undertake to review the history of this subject, as represented in our Transactions—still less to restate all the contributions to it which have been made in books or in papers before other technical societies, since the initiative was taken by the Institute. My more modest purpose is to indi-

Jan 1, 1899

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Charles P. Williams

The lead-bearing area of Missouri has been subdivided, geographically, into the Southeastern, the Central, and the Southwestern

By C. Dinis da Gama

In order to reduce the complexity of mechanisms influencing rock. fragmentation by blasting a simulation approach is proposed, using the capabilities of microcomputer interactive graphics. Situations involving cratering end bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By J. W. Pamplin

SOME 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.' Physically the phosphate-bearing formation, locally called the “matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca3P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by ½ mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, some- times a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the “hydraulic line." This 700 yd. of overburden and 300 yd. of matrix-1000 yd. in all- amounts to about 1500 tons of material moved each hour. The over- burden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7 ½ long tons in 4000 gal. of water per minute-a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938