Search Documents

By Robert F. Shurtz

When an ore deposit is evaluated on the basis of core sampling, questions always arise as to how much weight should be given the various sample grades and how the deposit should be divided into specific volumes assigned to corresponding grades. For a tabular deposit it is customary to use the so- called zone-of-influence. This zone is usually de- fined as the polygon in the plane of the deposit having corners halfway between a given core drill intersection and each of the nearest neighboring intersections. The volume of the ore in this polygon is assigned the analysis obtained from the drill core taken at the intersection. In massive or irregular deposits, volumes of various shapes may be defined with respect to the locations of drill core samples. These volumes may be regarded as three-dimensional zones-of-influence; the theory involved in assigning the values of the central analyses to the ore in the volumes is the same as that used in the case of a tabular deposit. The zone-of-influence method was used in evaluating one of the magnesite deposits at Gabbs, Nev.1-3

Jan 10, 1959

Flexibility is the keynote in designing modern exploration drills that and mobility. Add to the flexibility of individual drills the wide range of models, and the man looking for a drill has ample choice today. Weight? Choose from models as light as 50 lb or as heavy as 10,000 lb. Hole capacity? From less than 1 in. for smallest core drills to 20 in. or more for auger types. Transportation? The lightest go by packsack (in fact, that is one trade name) ; others are designed to go by Jeep, truck, on skids or are built on light trailers. Power? Select air power, gasoline or diesel engine, electric motor, or use a power take-off from the vehicle on which the drill is mounted. Drill bits offer almost as much variety as the drilling machines themselves. Many drills are suitable for a variety of uses, and often adapt to several types of bits with ease. Some of the types available are: diamond core, diamond reaming, rotary, auger, shot, and special soil sampling tools.

Oct 1, 1955

By William D. Klopp

A study was conducted of the tensile and creep properties of are-melted and electron-beam-melted tungsten over the temperature range 2250° to 4140°F. The tensile and creep strengths vary with pain size, the finer -grained materials being stronger. The activation energy for transient creep at 2250° to 3500°F is 95,000 cal per (g)(mole), while that for steady creep at 3300o to 4000°F is 141,000 cal per (g)(mole). At 2875o to 3300°F the apparent activation energy for steady creep decreased with decreasing temperature. It is suggested that cross slip is rate controlling during transient creep, while dislocation climb is rate controlling during steady creep above 3300° F. ALTHOUGH considerable data have been generated on the high-temperature tensile properties of powder-metallurgy tungsten,1 relative few data have been published on the properties of are-melted2 or electron-beam melted tungsten.3 Furthermore, the available data show a fairly large amount of scatter at high temperatures. The effects of structure and purity have not yet been defined, aside from observations that high-purity electron-beam (EB)-melted tungsten3 and single-crystal-plasma-flame tungsten4 are weaker than less pure powder-metallurgy tungsten. The creep behavior of powder-metallurgy tungsten has been studied, but no data are available on the creep behavior of tungsten consolidated by melting. Green5 found that powder-metallurgy tungsten exhibited linear creep at 4082° to 5072°F with an activation energy of 160,000 cal per (g) (mole). The similarity of this activation energy to that of 153,000 cal per (g)(mole) for volume self-diffusion6 suggests that recovery of strain hardening by dislocation climb is rate controlling in this temperature range. In studies at 4800°F, Sutherland and Klopp7 concluded that grain size significantly affected the creep behavior of commercial powder-metallurgy materials. This grain-size effect was suggested by sherby,8 although the opposite relation had been reported for aluminum.' The purpose of the present study was twofold: first, to provide baseline data on high-temperature tensile and creep properties of are-melted and EB-melted tungsten for concurrent tungsten alloy studies, and, second, to determine the phenomenolo-gical effects of structural and purity variables on the high - temperature mechanical properties of tungsten. EXPERIMENTAL The are-melted tungsten materials were prepared by melting sintered 1-1/4-in.-diam electrodes into 2-1/2-in.-diam by 5-in.-long ingots. The are-melting facility has been described previously.' Eight ingots were melted, machined, and hot-extruded at

Jan 1, 1965

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975

By J. H. Nelson

An outline survey of the economic outlook for the United States export trade in petroleum products resolves itself broadly into two general divisions; first, a consideration of our present position in this trade, and second, a discussion of the visible factors which promise to affect appreciable changes in the immediate future in that trade. The United States PetRoleum Exports of majoR Petroleum Products 1925, 1926 and 1927

Jan 1, 1928

By H. H. Podgurski, Hsun Hu

Large cryslals of high-purily iron (99.996+ pcl) cannot be obtained by the usual strain-ameal technique. Repealed phase transformation by thermal cycling prior to crilical deformation improves the capabilily of cryslal growith but fails to yield satisfactory crystals. Imperfect columnar crystals can be produced by the phase-transition method. The addition of a small amounl (0.005 wl pet) of nilrogen IT was reported'-4 that for metals of very high purity the usual procedures of the strain-anneal technique fail to produce large crystals. This was eliminates practically all the difficulties in crystal growth by the normal strain-anneal procedures. An actual example is presented, showing that most parts of a strip have been converted into a large crystal by this method. The addition of nitrogen, which can be removed from iron with less difficulty, is believed to be more desirable than carbon additions for the same purpose. thought to be due to the strong tendency for recovery in the high-purity metals: hence the critically strained matrix undergoes polygonization instead of recrystallization upon annealing for crystal growth. Talbot1,2 succeeded in overcoming this difficulty by adding 0.03 to 0.04 pct C to high-purity iron before critical deformation. followed by annealing in hydro-

Jan 1, 1965

By Harrison R. Cooper

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application knowledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By M. R. Pickus

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centered cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystalliza-tion has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers,6 were of a. qualitative nature. It is our hope that the present investigation may contribute some-thing to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938

By G. W. Preckshot, J. W. Gorman

MOLTEN metals offer an excellent medium for the study of molecular diffusion and interphase transfer. In the absence of intermetallic compound formation, solutions of molten metals are solutions of elements. Therefore, complicating factors such as molecular structure, dissociation, association, polarization, and so on, are generally absent. Further, metals remain in the liquid state over a wide range of temperature. Thus, the effect of temperature on transport processes can be studied in more detail. Although some data are available for the diffusion of metals in the molten state at high temperatures,"""".'!' the most useful and accurate data are those for the diffusion of various elements in mercury at room temperature. The effective radius of diffusion for the various elements in mercury may be calculated from the Stokes-Einstein relation.'-These calculated radii are compared with the atomic and ionic radii calculated from X-ray data on crystals." The effective radii of diffusion of the alkali and alkali-earth metals correspond to those of the neutral atom; those of cadmium, silver, lead, zinc, thallium, bismuth, and tin correspond to ionic radii; and those of copper and gold indicate larger radii due to association with mercury or more likely, faulty diffusion data. Independent evidence"' supports the notion that alkali metals are uncharged in amalgams. The concept of metals moving free of their conductance electrons in the liquid state has been discussed by Eyring, et al,'" in connection with studies on the viscosity of pure molten metals. Considering the approximate nature of the tabulated atomic and ionic radii and the variance in the diffusion measurements, the application of the Stokes-Einstein equation to the diffusion of metals in mercury gives gratifying results. It is noted that a number of these metals have article radii eaual to or less than those of the solvent mercury.".'*,"' Soba1,'" sing the inaccurate Roberts-Austin20 data, indicated that the effective radius of diffusion might well be a function of temperature. Additionally in studies of mass transfer between phases, many conflicting opinions have been expressed concerning the assumption of equilibrium at the interface." ,","," The results of the present work on the diffusion of solid copper in molten lead throws light on the tempera- ture variation of the diffusion radius as well as the extent of the interfacial resistance. The theoretical background and experimental procedure are presented here in detail. Results on other systems will be presented in subsequent papers. Nomenclature The following nomenclature is used in the paper: A—cross-sectional area of diffusion column, sq cm C, C,—concentration of solution and saturated solution respectively, g per cc D,D'—-diffusivity, sq cm per sec e—Naperian base h—ratio, k/D k—mass-transfer coefficient, cm per sec L—diffusion column length, cm n—series index q—flux, g per sq cm-sec r—radius, cm or A R—-gas constant t—time, sec T—temperature, K V—volume, cc w—weight of copper-lead alloy on copper cylinder WT—-total copper transferred to lead diffusion, column, g Z—distance from top of diffusion column, cm 2'—distance from copper-lead interface, cm (2' = L-2) u,,—roots of diffusion equation Mathematical Apparatus The model shown in Fig. 1 applies to the diffusion of solid copper into molten lead. Here Fick's first law may be written where all terms are defined in the nomenclature. It is assumed that the volume of the lead column is constant. This is justified since experimental densities compared favorably with calculated densities based on perfect interstitial mixing. Thus there is no counter diffusion of lead. It is clear that 2 in Equation [I] should be measured relative to the interface which moves relative to the diffusion cell but not to the liquid phase. Hence, the frame of reference is the plane of the copper-lead interface. The diffusivity calculated at constant volume, D", is that defined by Hartly and Crank" and is designated herein as D. No Interfacial Resistance—The two situations of the presence and absence of interfacial resistance will be treated. The simplest is the latter which re-

Jan 1, 1959

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have given much information concerning the miners, also I have discussed the choice of localities for mining, for washing sands, and for evaporating waters; further, I described the method of searching for veins. With such matters I was occupied in the second book; now I come to the third book, which is about veins and stringers, and the seams in the rocks1. The term "vein" is sometimes used to indicate canales in the earth, but very often elsewhere by this name I have described that which may be put in vessels2; I now attach a second significance to these words, for by them I mean to designate any mineral substances which the earth keeps hidden within her own deep receptacles.

Jan 1, 1950

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give them full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The officers of the Institute whose terms expire are as follows: President, William L. Saunders (not eligible for re-election). Past President, Charles F. Rand. Vice-Presidents, Thomas H. Leggett, District 0; Fred W. Denton, District 4.

Jan 9, 1915

By E. T. Turkdogan, M. T. Hepworth, R. P. Smith

The permeability of oxygen in 0 iron in the tempera-ture range 700" to 900 C and in 6 iron at 1450°C was determined by the rate of internal oxidation of iron, containing -0.1 pct Al. The solubility of oxygen in zone-refined iron was determined by equilibration with hydrogen-water vapor gas mixtures at 1450" and 1510°C; oxygen solubilities , for iron in equi1ibriu.rn with molten oxide, are found to be 66 and 83 ppm for these two temperatures, respectively. The diffusivity of oxygen in iron at 14500C3 as calculated from the permeability and solubility data, is (4.1 * 0.6) x 10 "B sq cm per sec. OXYGEN is one of the most common impurities present in iron or steel, mainly in the form of oxide inclusions. In the study of many metallurgical problems concerning solid iron, it is often desirable to know with a reasonable accuracy the solubility and diffusivity of oxygen over a wide temperature range. The solubility of oxygen in solid iron has been the subject of numerous studies yielding highly discordant results as seen for example from the literature surveys made by Meijering &apos; and Schenck et a1.&apos; As shown by Kitchener et aL3 and by Sifferlen, the high oxygen solubilities reported by many investigators are the result of oxidizable impurities which are often present in iron. In addition, there have been experimental problems associated with icaccuracy of oxygen analysis of iron containing less than 100 ppm 0. A number of studies have been made on the permeability of oxygen in a and y iron using Fe-Si, Fe-Mn, and Fe-A1 alloys in the internal-oxidation experiments.1&apos;2&apos;5&apos;6 However, no direct measurements have been made of the diffusivity of oxygen in iron. In the present work two sets of experimental measurements were made: permeability and solubility studies at 1450" and 1510°C and permeability studies only in the range 700 to 900°C. In both sets of permeability measurements slab-shaped specimens containing small predetermined amounts of aluminum in solution were exposed at constant temperature to gas mixtures of hydrogen, water vapor, and argon for varying times. These specimens were quenched, sectioned, and examined for oxygen penetration by metallographic observation of aluminum oxide particles which formed. From these data, it is possible to calculate the ratio of the diffusivity of oxygen in iron, D, to the equilibrium constant K for the reaction Hz(g) * O (dissolved in iron) = H,O(g). EXPERIMENTAL Permeability Measurements at 1450°C. An ingot of vacuum-carbon deoxidized iron containing 0.086 pct A1 was prepared, using commercial "Type lO4A Plas-tiron"; after hot rolling, specimens were machined into slabs a by 2 by 2 in. The impurity contents were: S, P < 0.002 pct; C, Mn < 0.01 pct; each of all other Usual impurities < 0.004 pet. The amount of oxide inclusions in this material, determined by a bromine-methyl acetate extraction, corresponded to about 20 ppm 0 in the iron which agreed well with the results of vacuum-fusion analysis. Each specimen was annealed at 1450°C for 1 hr in purified hydrogen, polished to a smooth surface, and then introduced into a controlled oxidizing atmosphere in a recrystallized alumina tube at 1450°C. The constant temperature zone (*3"C) was about 3 in. in length. The gas composition was controlled by mixing argon with hydrogen (using calibrated constant-head flow meters) and passing the mixture through a column of a mixture of oxalic acid dihydrate and 10 pct anhydrous oxalic acid, to establish a required water-vapor content in the gas mixture. The temperature of the oxalic acid dihydrate column was controlled by a thermostat. The total gas flow was in the range 800 to 1000 cu cm per min. The exit gas from the reaction tube was passed through a weighing bottle containing a desiccant, to cross-check the degree of water-vapor saturation, which for all experiments was about 97 pct of those derived from the data of Baxter and Lansing.1 For a typical experiment, a specimen was introduced into the furnace in a stream of dry argon and hydrogen. The specimen was then rapidly raised by a Pt-Rh alloy wire into the hot zone and allowed to reach the reaction temperature, at which time the oxidizing gas mixture was introduced. The oxygen potentials employed were sufficient to oxidize aluminum but not to cause liquid iron oxide to form. After a specified time, the experiment was ended by dropping the specimen onto a water-cooled copper block at the bottom of the reaction tube. The depth of the internally oxidized zone, hereafter called the "case", was determined by sectioning the specimen at right angles to the long direction. The section was then examined under a microscope equipped with a micrometer stage. In general, the oxide particles were fairly uniform in size and distribution, forming a reasonably well-defined interface between the oxidized and unoxidized region. A typical cross section as observed at X30 is shown in Fig. 1. A thermal macroetch was used in one selected specimen to delineate the case. A cross section of a previously oxidized slab was polished and reheated at 1450°C in a hydrogen atmosphere for about 10 min. Upon quenching, the surface relief shown in Fig. 2 was produced; causes of this effect are unknown. Permeability Measurements Below 900°C. A slightly

Jan 1, 1967

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By Herbert Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electro-static separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static elec-tricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor-generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the elec-trostatic separating process.

Jan 1, 1938

By A. G. Weber, K. H. Coats, M. H. Terhune, R. L. Nielsen

Two computer-oriented techniques for simulating the three-dimensional flow behavior of two fluid phases in petroleum reservoirs were developed. Under the first technique the flow equations are solved to model three-dimensional flow in a reservoir. The second technique was developed for modeling flow in three-dimensional media that have sufficiently high permeability in the vertical direction so that vertical flow is not seriously restricted. Since this latter technique is a modified two-dimensional meal analysis, suitably structured three-dimensional reservoirs can be simulated at considerably lower computational expenses than is required using the three-dimensional analysis. A quantitative criterion is provided for determining when vertical communication is good enough to permit use of the modified two-dimensional areal analysis. The equations solved by both techniques treat both fluids as compressible, and, for gas-oil applications, provide for the evolution of dissolved gas. Accounted for are the effects of relative permeability, capillary pressure and gravity in addition to reservoir geomety and rock heterogeneity. Calculations are compared with laboratory waterflood data to indicate the validity of the analyses. Other results were calculated with both techniques which show the equivalence of the two solutions for reservoirs satisfying the vertical communication criterion. INTRODUCTION Obtaining the maximum profits from oil and gas reservoirs during all stages of depletion is the fundamental charge to the reservoir engineering profession. In recent years much quantitative assistance in evaluating field development programs has been provided by computerized techniques for predicting reservoir flow behavior. Because of the spatially distributed and dynamic nature of producing operations, automatic optimization procedures, such as those now in use for planning refining operations, are not now available for planning reservoir development. However, present mathematical simulation techniques do furnish powerful means for making case studies to help in planning primary recovery operations and in selecting and timing supplemental recovery operations. A number of methods have been reported which simulate the flow of one, two or three fluid phases within porous media of one or two effective spatial dimensions>-4 However, applying computer analyses to actual reservoirs have been limited mostly to two-dimensional areal or cross-sectional flow studies for two immiscible reservoir fluids. To obtain a three-dimensional picture of reservoir performance using such two-dimensional techniques, it has been necessary to interpret the calculations by combining somehow the results from essentially independent areal and cross-sectional studies. To the authors&apos; knowledge, the only other three-dimensional computational procedure, in addition to those presented here, was developed by Peaceman and Rachford8 to simulate the behavior of a laboratory waterflood. Two computational techniques which may be used to simulate three-dimensional flow of two fluid phases are described in this paper. The first method, called the "three-dimensional analysis", employs a fully three-dimensional mathematical model that treats simultaneously both the areal and cross-sectional aspects of reservoir flow. The second method, called the vertical equilibrium (VE) analysis", is applicable

By E. P. Pfleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed pressure, see Fig. 2. The

Jan 1, 1952