Search Documents

By C. F. Cockrell, H. E. Shafer, J. W. Leonard

A significant technological development is discussed for the processing of certain power plant flyashes that are a problem because they contain a high water-soluble mineral content and yield inferior flyash-based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash-based structures. Favorable changes are evi-dent in sodium silicate consumption, where about half the amount used for making brick from normal flyash is required, processing costs, and strength and appearance of the resulting freshly formed green and fired structural products. In some high cost in-stances (above the $30 or less per thousand brick estimated for normal flyash), hydrochloric acid additions can replace or reduce other costly additives normally required for problem flyashes. This results in savings of as much as $9 per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble sulfur as a result of the eventual application of certain experimental air pollution control processes. Much of the research datal-6 accrued through work by the Coal Research Bureau of West Virginia University for the Department of Interior's Office of Coal Research on converting waste power coal ash to valuable brick and other structural products, can be categorized as follows: (1) general ash-to-brick tech- nology; (2) specific ash-to-brick optimization; (3) pilot plant progress; (4) production cost estimates. A summary of the progress on bench-scale experiments indicates that coal ash can yield two types of brick. An acceptable brick is obtained by mixing 73.6% fly-ash, 23.5% bottom ash and 2.9% sodium silicate solution (dry basis). Depending on the flyash and bottom ash used, optimum brick can be manufactured by mixing 72-77% flyash, 20-25% bottom ash and 2.3-3.0% sodium silicate (dry basis) with Na2O : SiO2 ratio varied according to the composition of the flyash used. These blends are thoroughly mixed and mechanically formed into green brick shapes at pressures ranging from 1000 to the more usual 3000 lb per sq in. The green shapes then are dried and fired at temperatures ranging from 1975-2150°F using clay brick cycles that are shorter than standard. Other findings reported to date indicate that when making optimum brick, it is necessary to carefully control the top size of the moisture-releasing bottom ash so that it falls between 8 and 30 mesh, depending on the flyash used. Moreover, the chemical composition of bottom ash and flyash have been found to be of little significance with the exception of a few problem flyashes which are the subject of this paper. Finally, the pilot plant, which was previously reported under construction, is now in operation. This will indicate, among other things, the cost of brick production, which was earlier estimated for non-problem flyashes at $30 or less per thousand brick. The foregoing bench-scale technology is applicable to all the initially tested ashes as well as to the majority of ashes examined during the course of research. However, a few of the ashes yield green and fired products that may be structurally inferior or unacceptable, necessitating excessive and diverse reagent addition, and/or may be coated with unsightly surface deposits. These problem ashes generally originate in certain areas of Illinois, western Ken-

Jan 1, 1969

By Robert H. Richards

During tile summer of 1870, I had an opportunity to visit the laboratory of the late David Forbes, Esq., in London, and was much interested in a labor-saving device which he had attached to his agate mortar. The mortar was placed in the centre of a small table, and about ten inches to the right of the mortar, a post, perhaps two

Jan 1, 1879

By Frederic E. Carter

THERE have been many attempts to prove that platinum was known to the ancients, but since no traces of the metal have been found in the relics of early times, it must be concluded that it was not known to them. As far as records go, it was actually first discovered in the 16th century in a Spanish mine on the Pinto River in South America; from which source it received its name of Platina del Pinto (little silver from the Pinto). It was more or less of a rarity and was a subject of interest to a few chemists only, until the year 1822 when the metal was first discovered in Russia. In 1819 there were noticed in the washings of the gold sands of the southern part of the Ural Mountains, grains of a heavy white substance, but it was not until three years later that this substance was found to contain platinum. While at first the amounts of platinum brought from the Urals were meager, prospecting soon disclosed rich deposits extending over a considerable area, and nuggets from 10 to 20 lb. were by no means rare. This discovery assured to chemists an ample supply of platinum for their crucibles, etc. The ore is now found in various parts of the world but the richest deposits are still found in the Ural Mountains. The platinum of commerce is obtained entirely from alluvial deposits at depths varying from 6 to 40 ft. The sand and gravel of former river beds are subjected to a series of screenings and washings to effect the separation of the ore. Actually, probably all gold-bearing gravel beds of the world contain platinum, and it is more than likely that large quantities of platinum ore have been thrown away with the black sand washings from gold placer deposits. This is especially true of the alluvial deposits of the Pacific Coast in California and Oregon. Platinum ore is usually found in the form of rounded or flattened grains of "sand," and occasionally in irregular lumps of the size of peas. Large nuggets are very rare. The ore has a metallic luster and is distinguished by its steel gray color, but shows light gray streak when rubbed on a hard white surface; it has a high specific gravity, 16 to 19; is infusible in the hottest blast furnaces, and insoluble in any single acid. Platinum ore is a complex body consisting of the metal in combination with varying proportions of the other members of the platinum group; iridium,

Jan 1, 1928

By L. C. Graton

I. INTRODUCTION. The Relations of Scale in Geologic Work. MANY features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly on this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.1 Thus, a mural

Jan 5, 1913

By Henry Sturgis Drinker, Rossiter W. Raymond

Jan 1, 1914

By Bauer. Larry G.

The vast coal reserves in the Wyoming, Montana, North and South Dakota region are sufficient to supply the total energy needs of the United States for several hundred years. Not only is there an abundance of this sub-bituminous and lignite coal available, but it is easily obtainable by strip-mining . The overburden varies from several feet to several hundred feet. This western coal has yet another asset, namely, a low sulfur content. Whereas eastern and midwestern coal has a sulfur content of 2.5%, the upper Great Plains coal contains sulfur in the 0.5% range. The importance of the sulfur content of the coal is a direct result of federal government emission standards for sulfur dioxide (SO2). Hand (1) points out that "sub-bituminous coals and lignites have a propensity for retaining this sulfur in the ash under certain conditions which is not evident in higher rank coals." This would tend to reduce further the SO2 concentration in the combustion gases of boilers. Western coal is no panacea, however, in that it is far removed from most population and industrial centers. Furthermore, the moisture content of the coal varies from 20 to 40%. This moisture is almost exclusively inherent, that is, it is chemically and physically bound to the organic matter of the coal. It is believed that the water forms a part of the coal structure perhaps as water of hydration of organic salts or organic acids, perhaps by hydrogen bonding, or perhaps by simple adsorption (2). The primary market for this coal is the electric power industry. Lesser markets will be as coke for the steel industry and possible as a raw material for coal gasification and coal liquefaction plants.

Jan 1, 1983

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By R. M. Daelen

Mechanical science is severely tested by the demands of the iron manufacture for the varied apparatus needed to transport and to treat raw materials and products. Water has long been a favorite means of transmitting pressure for such purposes, because of its own incompressibility. Further advances in its use are the more to be expected, since mechanical improvements have steadily tended to overcome the difficulties formerly encountered in the employment of great hydraulic pressures. So long as the pressure is not higher than that which requires for plungers, etc., only ordinary stuffing-boxes, with hemp or other similar packing, the necessary arrangements for the production and transmission of the water-pressure without leakage are very simple. But when this limit (which is, for most purposes, 50 kilos to the square centimeter) is exceeded, new conditions of construction arise, which are met in various ways, and which justify a primary division of hydraulic presses into low-pressure and high-pressure respectively. The former are used in lifting and moving weights, and employ pressures as high (in extreme cases) as 100 kilos per square centimeter; but at this point the friction between piston and hemp-packing is so great that the use of cup-leathers is already preferable. Beyond 100 kilos it becomes a necessity. The range of practicable tight packing which follows is considerable, extending to about 1000 kilos; but "high pressure" in practice is from 100 to 600 kilos, and it is to this that the present paper applies. General Classes and Types. Hydraulic transmission at high pressure usually claims consideration in case the solid mechanism, such as levers, cams, screws, and gear-wheels, would have to be too large, would involve too much friction, or could not be suitably adapted to the speed-requirements of the working-tools. Since steam is mostly the primary carrier of

Jan 1, 1893

By E. A. Gulbransen, K. F. Andrew

THIS paper. will present the results of our studies on the kinetics of the gas phase reactions of co-lumbium and tantalum with O2, N2 and H2. Studies on zirconium and titanium have been previously reported.9,11 Due to their high melting points and their many excellent physical and chemical properties, colurn-bium and tantalum have been finding their places as useful metals in science and industry. Chemically the metals are very inert to gas and liquid phase corrosion at room temperature. However, at moderate temperatures of 250°C and higher the metals react readily with oxygen and hydrogen. It is of interest to study the gas phase reactions of these metals for the following reasons: (1) to compare the rates of the several reactions with those of other metals and to correlate the rate data with theory and structure predictions, (2) to add basic information on the practical difficulties of the reduction, refining and working of columbium and tantalum, (3) to anticipate new uses for the metals and (4) to understand the role that the metals play as components in high temperature alloys. Literature Survey A number of papers exist in the literature on the gas phase reactions of columbium and tantalum with O2, N2 and H2; however, only fragmentary data have been reported on the kinetics of these reactions. Although the free energy of formation of the oxide Ta2O520at 25°C has been determined and some thermodynamic work has been reported on columbium and its oxides, the data are not sufficient to make equilibria calculations at elevated temperatures. Oxidation: 1. Kinetics: The rate of oxidation of columbium and tantalum has been studied by McAdam and Geil23 using the interference color method. Tantalum is reported to oxidize more slowly than columbium, zirconium and iron. The amounts of oxidation of columbium after 20 hr in air for several temperatures are reported by the Fansteel Metallurgical Corporation.36 Columbium starts to oxidize in air at about 200°C. The oxide is said to be adherent and prevents further oxidation until the temperature is raised. Columbium is reported not to become brittle on heating in air for short periods like tantalum because the oxide film prevents further reaction. The columbium oxides dissolve into the metal when heated in a vacuum at temperatures between red heat and 1200°C. Above 1200°C the oxides are reported to evaporate. Columbium, in the oxide free state, is an active getter in vacuum tubes. 2. Preparation and Structure: G. Grube, O. Kuba-schewski and K. Zwiauer15 have studied the decomposition of Cb2O5 in argon. They find that CbO2 is formed slowly at 1150° and rapidly at 1300°C. Cb2O5 can be reduced to CbO2 by moist H2. The reduction of this dioxide to the lower oxides is rapid. By varying conditions CbO2, Cb2O3, CbO and Cb2O can be formed. CbO2, CbO and Cb2O have independent lattices while Cb2O3 is a stoichiometric mixture of CbO and CbO2. In a later paper O. Kuba-schewski" has shown that CbO is cubic and that CbO2 has a rutile type of lattice. The most exhaustive work on the oxides of columbium is that of G. Brauer.8 The number and constitution of the solid phases in the binary system Cb-O were investigated by the preparative, analytical and X ray methods. He indicates that only the oxides Cb2O5, CbO2 and CbO exist with limited regions of homogeneity. The solid oxide Cb,O, exists

Jan 1, 1951

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division J C Kinnear, Jr, President A W Thornton, Past President W R Hibbard, Jr, Vice-President R W Shearman, Secretary-Treasurer AIME, 29 West 39th Street New York 18, N Y Board of Directors J B Austin, D L Clark, H B Emerick, T D Jones, H H Kellogg, C T Marshall, E E Schumacher, C S Smith, J D Sullivan

Jan 1, 1957

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1941 and re¬ports for the same year of the following standing committees: Admissions, Mem¬bership, Papers and Publications, Mining and Metallurgy (Magazine), Library, and Student Relations. These reports present additional details. Membership For the fourth year in succession, mem¬bership reached a new all-time high, level as shown in Table 1. The total at the

Jan 1, 1942

By A. W. Griffith, R. G. Beverly, W. A. Millsap

THE Grand Junction Pilot Plant, operated by National Lead Co. Inc., for the U. S. Atomic Energy Commission, is engaged in the amenability testing of orebodies to establish design and cost data for commercial mills and to test new processes for recovery of uranium from ores. Test work was performed to study the effects of several variables on leaching of uranium ores in carbonate solutions. Many of these variables had been investigated in the laboratory, but pilot plant tests were desirable to evaluate their importance in semi-works equipment and to predict optimum operating conditions for future commercial mills. The results of these tests should serve as a guide in selecting the most efficient and economical method of leaching uranium ores amenable to a carbonate process. This article is concerned with a process in which uranium is extracted from the ore by a hot Na2CO3- NaHCO3 solution; the uranium-bearing solution is separated from the solid residue by filtration, and uranium is then precipitated by chemical means.

Jan 9, 1957

By Albert Sauveur

THE following experiments were conducted in order to study the influence of the rate of cooling through and below solidification on the dendritic structure (macrostructure) and microstructure of some hypoeutectoid steel. The steel selected was of commercial grade and had the following composition: C, 0.40 per cent.; Mn, 0.85; Si, 0.70; P, 0.099; S, 0.043. After melting in vacuum in an Arsem furnace, the various samples were allowed to solidify and to cool to room temperature as indicated in Fig. 1. Samples were thus obtained representing all possible combinations of slow and fast cooling through the various ranges of temperatures indicated, namely: (1), zone of solidification or primary crystallization, (2) zone of granulation, and (3) zone of secondary crystallization. The location of the different temperature zones in the iron-carbon equilibrium diagram is shown in Fig. 2. The authors adopted. Belaiew's notations. The designations of the various samples readily indicate their treatment, as will be apparent from Table 1.

Jan 1, 1930

By John D. Ridge

For mining geologists, the most important trends during 1962 have been the increased concentration of the exploratory activities of American mining companies in the United States and Canada and the greater use of the combined techniques of geology, geophysics and geochemistry in searches over larger areas for wider varieties of metals and minerals. The principal reasons for these changes in approach have been the deterioration of the political-economic climate in many areas of the globe of equal or greater geologic promise and the realization that modern exploration is most efficiently and economically conducted through the use of all available means of detecting ores in areas sufficiently large to raise to a maximum the chances of success. The attitude of certain major U.S. metal-producing companies can be shown by the officially ex- pressed positions of their principal officers. Early in 1962, Clyde E. Weed, Chairman of the Board of Anaconda, remarked that "because of unsettled conditions and disruptive influences in many of the copper-producing areas of the world, it is imperative that domestic copper-producing capacity be improved and made as efficient as possible in order to meet consumer demands at reasonably stable prices." In November, Robert G. Page, President of Phelps Dodge, pointed out that his company is not only concentrating most of its exploratory effort on this continent but is also increasing the number of metals for which it is searching. Frank R. Milliken, President of Kennecott, recently said that "most of our exploration money is going into the northern part of the Western Hemisphere."

Jan 2, 1963

By Franz Posepny

CONTENTS. Introduction. Part I. General Facts And Theories. [ ]

Jan 1, 1902

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By C. R. Austin

In a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreasing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test have also shown promise as providing a "merit index" of high-temperature serviceability.= Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350" C. (and a maximum of 450" C. for alloy steels) to serve as a suitable basis for comparison evaluations of materials and for judging permissible stresses. Koerber and Pomp consider, however, that above these temperatures creep limit must be substituted for the high-temperature yield point as the all-important characteristic of the material. Whatever may be their definition of

Jan 1, 1934

By David A. Thomas, John F. Peck

Fibrous microstructures and their development have been studied by metallography and by hardness and quantitative metallographic measurements. Thin, curved grains were observed in transverse sections of commercial tungsten wire and were developed in laboratory-drawn iron wire at reductions greater than about 70 pct. The unusual grain shapes are attributed to the nonuniform mode of deformation of the grains associated with the characteristic [I101 preferred orientation that develops in bcc metals during drawing. Transverse sections of heavily swaged iron wire showed a ospiral nebulao structure that appears to result from the elliptical shape of the cross section of the swaging dies and their rotary motion. Hardness and quantitative metallographic results show unusual trends that parallel the changes in microstructure. Other phenomena are considwed in light of the results, including the strength of fine wires of bcc metals, ocylindricalo textures, and the ductility of fibrous tungsten. 1 HE microstructure of tungsten wire in a longitudinal section shows grains highly elongated in the working direction, giving the appearance of a bundle of parallel fibers, Fig. l(a). Wires of tungsten and other bcc metals show a pronounced preferred orientation in which a [I101 direction is parallel to the wire axis.l The microstructure and texture of tungsten develop during warm working (working above room temperature but below the recrystallization temperature) into wire by swaging and drawing. Fibrous tungsten so produced has limited but useful room-temperature ductility, whereas annealed tungsten is brittle at room temperature. During an investigation of the effect of recovery annealing on the substructure of commerical 0.030 in. diam tungsten wire, it was found that transverse sections of the as-received material showed thin, curved grains, Fig. 1(b), instead of the expected equiaxed grains. The fact that Figs. l(a) and (b) show different sections of the same material at the same magnification is at first disconcerting, because the long dimension of the curved grains in the transverse section is several times the average fiber width in the longitudinal section. However, a longitudinal section cuts most of the curved grains across their narrow dimension, giving the appearance of a multitude of narrow fibers. On the other hand, the plane of a longitudinal section occasionally includes a long dimension of a curved grain, resulting in a broad ofibero, such as A in Fig. l(a). EXPERIMENTS AND RESULTS To investigate the origin of fibrous microstructures and particularly the unusual transverse-section structure of tungsten, rods of iron (also bcc) were drawn and swaged in the laboratory. One rod of annealed Ferrovac E was drawn in six steps to a total reduction in area of 87 pct (0.10 to 0.036 in. diam), and a second rod was swaged to the same reduction, using approximately the same reduction steps. Longitudinal and transverse sections of the swaged and drawn iron wires are shown in Fig. 2, for reductions in area of 39, 73, and 87 pct. A fibrous microstructure in longitudinal section is first evident at 73 pct reduction, and it is further developed at 87 pct reduction. The grains in transverse section remain equiaxed until about 73 pct reduction, when they become somewhat elongated and curved. At 87 pct reduction, the drawn wire shows thin, curved grains in the transverse section, similar to those observed in tungsten. The transverse sections of the iron wires swaged 83 and 87 pct reduction in area show the striking ospiral nebulao structure in Fig. 2(d). This struc-

Jan 1, 1962