Search Documents

By T. F. Witherbee

IT is proposed to give, first, a description of the works ; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

Jan 1, 1876

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By CARL B. SNYDER

PERHAPS the most extraordinary thing about business, the trade and production of the country as a whole, is its amazing continuity and growth, its momentum and energy. It goes on year after year, growing steadily, almost without breaks, in spite of every kind of disturbance. We have been grossly deceived into the idea that business is highly variable. We have taken a few things like pig iron, and the like, constructional activity broadly, and imagined that these are a trustworthy measure of trade. Actually they are the worst that we could find. They do not apply to more than 10 per cent or, at the most, possibly 15 per cent of the total of the country's industrial activity. The other 85 or 90 per cent, or even more, goes on growing surely and steadily just like the growth of population and the steady advance in technique, invention, discovery, and improved methods of production Let me give you what seems to me one of the most remarkable examples of this amazing momentum and regularity. You know that 90 per cent or more of the business of the country is done 'by means of checks. About seven-eighths of the total of all checks drawn are reported regularly every week in the newspapers. Let us follow these reports from week to week, just as they come, and plot them up against the correspond- ing weeks of last year, and the year before, and the gear before that, as far back as you would like to go. Take especially the figures for 140 selected cities out- side of New York.

Jan 1, 1929

By E. J. ENGEL

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Grenville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New York State include earth materials of differ- ent chemical and mineral compositions. In general the mineral talc is sub- ordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits.

Jan 1, 1949

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By Charles W. Dickson

Jan 1, 1904

By AIME AIME

THE Committee on Elimination of Waste in industry came into existence from a speech in Washington by Mr. ,Hoover, in November, in which, he said: It is primary to mention the three-phase waste in production: first, from intermittent employment; second, from unemployment that arises in shifting of industrial currents; and third; from strikes and lockouts. Beyond this elimination of waste there is another field of progress in the adoption of measures for positive improvement in production.

Jan 1, 1921

By GUY C. RIDDELL, Donald M. Liddell

THE electronic arts today constitute the outstanding development in the field of rare metals, if not indeed in the arena of scientific progress at large. The year 1930 may become known as the year in which the electronic tube took hold of the wheels of industry; it is the year in which the tube's emancipation from the art of communication was proclaimed. The little tube which made a $500,000,000 industry out of a vacuum has now been applied to mining, manufacturing, transportation, chemistry, and other industries. Not many appreciate the extensive utility that e1ectroni.t tubes have already found in transportation, where they control the speed and security of express trains, as well as operate traffic lights on important highways-in the case of the Detroit-Windsor bridge counting the traffic and instantly turning the reports into the superintendent's office some distance away. In an Ohio steel mill, ten-ton ingnts 'rash back and forth through the rolls, reversed by their own shadows. The vacuum tube also starts, stops, and levels, fast passenger elevators.

Jan 1, 1931

By A. E. Himebaugh

A SEMI-AUTOMATIC hoist has been installed at the 2966 station of the Copper Queen mine, since neither the bulk of supplies handled nor the number of men engaged in developing the 3100 level justifies the constant attendance of two cagers and two hoist operators. The connecting service shaft between the 2966 and 3100 levels is actually a two-compartment raise. Below the 2966 level the shaft is 7x13 ft-slightly oversize to permit downcast ventilation and provide space for the 16-conductor flexible control cable. The raise extends 52 ft above the 2966 level for a 3-ft diam head sheave. Another 3-ft sheave is mounted as an idler between the hoist and head sheave, eliminating the need for an inclined cableway. The main compartment serves as a cageway; the other compartment provides a manway and space for service lines. Since vertical travel is limited, rope speed is of minor importance.

Jan 5, 1958

By Dudley L. Davis, E. C. Peterson

Introduction The Darwin District is 30 miles east of Olancha which is 220 miles north from Los z4ngeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacemerit of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were dis'Overed in the early seventies. BY 1875, Darwin had a population Of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation Of metal prices caused intermittent operations until World War 11. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. 'or the Past two Years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 Pct Of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. General Geology The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably pennsyl-vanian in age. These rocks have been intruded on the Rest by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills, The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 75°W, dips steeply south and is traceable for about 10 miles. It is a normal

Jan 1, 1949

By J. L. Bray

ACCELERATED programs, as discussed in this paper, refer to the year-around operation of a college or university with three sixteen-week or four twelve-week terms per year, with pauses between sufficient only to allow the administrative group to perform their functions. In most engineering schools, under such conditions, the conventional four-year course can be condensed to two years and eight months. These accelerated programs of study, which now exist in most of our technical institutions, were forced upon us under the influence of the outburst of wartime patriotism, perhaps one might go so far as to call it hysteria. Many of us felt and hoped that these programs were temporary expedients, but the cold hard threat of permanency now rears its head; consequently we should examine the merits and shortcomings of the new order, and evaluate its effect on our educational system, since it may persist in some form in the postwar years, because of the changing political and financial situation. Many engineering students are being educated in state supported institutions

Jan 1, 1944

• Phelps-Dodge Corp. signed an agreement with the Defense Materials Procurement Agency to increase copper production from the east ore deposit of the company's Copper Queen branch at Bisbee, Ariz. The company agreed to undertake a $25 million expansion program, including construction of a concentrating and leaching plant at the Bisbee mine and enlargement of the Douglas smelter. The Government agreed to buy the first 112,500 tons of the first 150,000 tons produced at 22e per lb if the company could not sell at a higher price. The new facilities will have a yearly capacity of 38,000 tons and should be in production by late 1954 or early 1955. • American Smelting & Refining Co. has started construction of a new building to house the Central Research laboratory at South Plainfield, N. J. It will have approximately 75 individual laboratories and an equal number of offices and shops. Modern apparatus to be installed will include electron microscopes, electric and fuelfired furnaces, miniature copper refineries and zinc plants, wire drawing machinery, and large pilot plant laboratory. In the new building scientists study the base metals, and the development of new uses for a number of Asarco by-products, arsenic, and little

Jan 11, 1951

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By C. O. Lee, R. H. Feierabend, Z. W. Bartlett

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By J. E. Breen, J. Weertman

The creep rate of polycrystalline tin was studied as a function of temperature and stress in constant stress experiments. The temperature was varied from room temperature to almost the melting point of tin. Activation energies were calculated from tests run at the same stress. It was found that on a log creep rate vs inverse temperature plot the experimental points did not fall on one straight line but on a line which changed its slope in the 90° to 160°C region. Two activation energies for the creep of tin can be calculated from the data: a value around 26,000 cal per mol at high temperatures and a value around 11,000 cal per mot at low temperatures. It is suggested that the discrepancies between the creep activation energies and those of self-diffusion can be accounted for if self-diffusion takes place predominately by Zener's ring mechanism rather than through vacancy or interstitial movement. SHERBY, Orr, and Dorn' and Dorn' have recently reviewed some of the data on high temperature creep of metals. -The data show that the activation energy of high temperature creep is approximately equal to the activation energy of self-diffusion. This same correlation has also been successfully made between the activation energy of grain boundary relaxation and that of self-diffusion.3,4 The metal tin does not fit into this simple picture. Its activation energies of self-diffusion differ appreciably from that of grain boundary relaxation and of creep. Fensham,5 from a precisely performed experiment, has determined that the activation energies of self-diffusion of tin are 10,500 and 5,900 cal per mol along the C and A axes, respectively. There are two energies because of the anisotropic nature of tin. Rotherham, Smith, and Greenough6 have shown that the grain boundary relaxation activation energy is 19,000 cal per mol (measurements made from room temperature to 100°C). Puttick and King7 found the same activation energy for grain boundary slip in bicrystals of tin (180° to 225°C region). Until recently, there was no high temperature large strain creep data on tin suitable for activation energy calculations. At rather small strains (up to 0.01), Tyte8 had made a series of measurements on tin from which activation energies can be calculated. In Fig. 1 are plotted some of his data on a log creep rate vs inverse temperature graph. It can be seen that Tyte's work indicates that at a relatively low temperature the activation energy is around 7,400 cal per mol but at higher temperatures the activation energy increases. Since Tyte measured the creep only for small strains, it is doubtful if a

Jan 1, 1956