Search Documents

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

The main orebody of the Bodangora mine is a metalliferous quartz reef within a major fault plane in the strongly folded and faulted volcanic rocks of the Ordovician-Silurian Oakdale Formation. The similarity of the type of mineralization to that of other pyrometasomatic deposits in this area suggests that the mineralizing fluids originated in the nearby Wuuluman Granite.The associated Mitchell&apos;s Creek West or Dick&apos;s reef is discussed briefly.

Jan 1, 1970

By B. Asbury, M. Cigla, C. Balci

The Western Mining Resource Center (WMRC) at the Colorado School of Mines (CSM) received a grant from the National Institute for Occupational Safety and Health (NIOSH) to perform a study that will help reduce the amount of respirable dust generated from the cutting of coal. The study is based upon laboratory testing and field experience. This information is being used to develop a new cutterhead design in conjunction with Joy Mining Machinery. The new cutterhead design is being evaluated with existing computer models developed at CSM. The new continuous miner cutterhead will be tested at the Twenty Mile Coal Company’s Foidal Creek Mine. Baseline testing with the current cutterhead will also be performed. This paper presents laboratory test results, design methodology, and test results performed to date.

Jan 1, 2002

Barrick Gold plans to have four new gold mines in production by 2006. Together, the mines would increase the company’s output by 40 percent. The projects include Veladero in Argentina, Alto Chicama in Peru, Cowal in Australia and Tulawaka in Tanzania. All of them are scheduled to begin production between the first quarter of 2005 and the first quarter of 2006. They are expected to drive Barrick Gold’s growth profile to a target of 211.5 to 217.7 t (6.8 million to 7 mil-lion oz) of gold production in 2007. The company’s projected output for 2004 is 152.4 to 155.5 t (4.9 million to 5million oz) in 2004. Overall, higher production and lower costs are expected in the early years from the new mines.

Jan 1, 2004

Polyacrylamide flocculating agent has been used in the Leaching Division &apos;of the Risdon Works of the Electrolytic Zinc Company of Australasia Limited since October, 1960. The number of thickeners in the continuous thickening stage was thereby reduced from eight to three. There has been an increase of 25 per cent in throughput and a reduction of solids in thickener over-flow from 3-4 g/l. solids to 0&#183;5 g Ir. solids. Reagent addition has been at the rate of 0&#183;25 lb Separan NP10 per ton solids.Additionally there has been a gain of 3 per cent in current efficiency as the direct result of the addition of Separan NP10 to purified cadmium sulphate solution priOl; to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strippings from 47 to 71 hr. However, there has been a slight increase in the lead content of the cadmium metal produced.The use of Separan NP10 to settle copper bearing residue in a batch process stage has resulted in a five-fold increase in settlement rate and a reduction in purification cycle time.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Limited, Risdon, Tasmania, produces zinc by electrolysis of purified zinc sulphate solution, the raw material being zinc sulphide concentrate. In the Risdon process (Van Arsdale, 1953; J ohnstone, 1953; Ross, 1949) the compound zinc ferrite (ZnO.Fe203) is formed during the concentrate roasting stage. When the roasted material is leached in dilute sulphuric acid the zinc ferrite is not attacked, and it remains as part of the insoluble leach residue, of which it may form as much as two-thirds of the whole. The remainder is mainly unroasted zinc sulphide, unleached zinc oxide, lead sulphate, gypsum, silver compounds etc. The zinc in the residue may be 10 per cent of that in the original concentrate.Continuous thickeners are used to recover the valuable residue from the impure zinc sulphate solution and the...

Jan 1, 1963

The spatial distribution of copper grades at the Mansa Mina project is highly variable due to the presence of high grade copper/silver/arsenic breccia bodies. Copper grades within the breccia bodies tend to average about 4.5% copper while grades in the surrounding stockwork average about 1.0%. The breccia is known to occur in the vicinity of significant controlling structures, however, the outline and therefore the thickness of the bodies are far from regular. Due to the high grade of these bodies a significant proportion of the value of the project is derived from the breccia tonnages. The irregularity in the outlines/thickness translates into an uncertainty in the breccia tonnage and therefore in the value of the project. Acknowledging the economic importance of the breccia bodies and the risk associated with the breccia tonnage uncertainty, significant additional drilling has been proposed to both understand the spatial distribution of the breccias and reduce project risk. The costs associated with this additional drilling are not inconsequential; thus, a reasonable question is ‘what value is derived from this additional drilling’? To obtain an answer to this important question, a simulation approach is applied. First the deposit is simulated using the existing drilling and the uncertainty in the resource is defined. Next the proposed drilling program is simulated and the simulated data are added to the existing data. Using this expanded data set a second simulation of the deposit is created and once again the uncertainty in the resource is defined. Using this approach, the reduction in the uncertainty in the resource can be determined. To convert this reduction in uncertainty (or reduction in risk) in the stated resource into a dollar value, a method of defining the increase in the project rate of return necessary to account for risk is presented. Using the two different rates of return, the difference in project NPV and hence the value of additional drilling is determined.

Jan 1, 2003

By Tony Mazzo

It has often been said by consulting engineers that foundation contractors are in the business of taking risks. One would agree that the mere fact a foundation project can be budgeted, planned, engineered and executed solely on the reliability of eight test borings made at a proposed site having an area of approximately 19,000 square feet, is a risky proposition, in and of itself. Now imagine that this site is actually one half of a city block located in an urban setting in an old, congested, historical neighborhood, surrounded by narrow city streets and historic landmark buildings. And suppose that the required depth of excavation for the construction of the new building on this site is approximately 35 feet and the natural groundwater table is at a depth below existing grade of only 25 feet. Given the difficult site conditions outlined above, one could certainly add the words "challenging" and "complicated" to the inherent word "risky" when describing the construction techniques involved to undertake a foundation project of this magnitude. This case study will discuss in detail how the excavation, sheeting, dewatering and underpinning work was accomplished as well as the problems overcome along the way.

Jan 1, 2003

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

Geochemical projects in progress or recently completed in the Bureau of Mineral Resources, Geology, and Geophysics (BMR) cover a wide range of topics and include research projects, regional studies, and prospecting programmes. However, in these notes emphasis is given to projects which are directly relevant to mineral exploration.FIELD INVESTIGATIONSStream sediment sampling, rock and soil sampling, and geobotanical surveys have been used by the BMR in a number of areas, partly in attempts to locate specific zones of mineralization, and partly to investigate the effectiveness of the various methods under different conditions of climate and topopraphy and in different geological settings.Stream sediment sampling has been most successful in the Territory of Papua and New Guinea. For example, in the South Sepik area, zones of disseminated su1phide mineralisation were found to give rise to anomalies with peak values of up to 1,000 p.p.m. copper, compared with background values of about 40 p.p.m. (Dow et al., 1968). By contrast, the results of rather limited work in the Northern Territory and in the Kimberley district of Westen Australia were inconclusive.Rock and soil sampling, on the other hand, was successfully used in a number of areas in Northern Australia, particularly at Rum Jungle and Tennant Creek.Rum Jungle area In the Rum Jungle area, where uranium and base metal mineralization is mainly associated with a Lower Proterozoic black slate sequence, samples, of c-horizon soil or weathered &apos;rock are generally collectedfrom the bottom of drill holes, usually 15 to 20 ft deep, bored with a power-operated auger.Surface sampling indicates that such a technique would probably have shown up all the major geochemical anomalies delineated by deep sampling, but the latter gives slightly more consistent and slightly

Jan 1, 1970

For establishing sustainable material cycle process in human system, a brand new concept should be created, which could recycle the waste materials, which are land-filled and discarded under present economical situation. The concept of &apos;RtoS&apos; (Reserve (of waste) to Stock) to create &apos;artificial deposit&apos; of the materials concentrate is one of the best ideas to be applied. From this viewpoint, separation technology, in especial, solid phase separation such as mineral processing technology contributes much to the concentration, making &apos;artificial deposit&apos; with less energy consumption compared with melting and/or dissolving technologies. Results of rare metals concentration in the e-waste are also introduced as an example with combining novel comminution and parts/powder separation.

Sep 13, 2010

Typically, large volumes of data are collected during geotechnical investigations for mining projects but rarely is this done in a comprehensive manner that enables all aspects of the geotechnical environment to be evaluated. A geotechnical core logging process has been developed to record mechanical and structural properties of the rock mass. The method enables data for a wide range of rock properties and geotechnically significant major structures to be collected including rock strength, joint surface condition, fracture frequency and fracture orientation. The logging method is unique in that sufficient data is collected to enable the independent determination of all the major rock mass classification systems including rock mass rating (RMR), (Bieniawski 1976, 1989; Laubscher, 1990) Norwegian Geotechnical Institute (NGI) tunnelling quality index (Q) (Barton, Lien and Lunde, 1974) and geological strength index (GSI) (Hoek, Kaiser and Bawden, 1995). The logging system has been specifically developed to allow better and more precise appreciation of rock mass and structural conditions across the project area thereby optimising the use and application of the available geotechnical data and improving confidence in the outcomes of geotechnical investigations. This paper describes the core logging process with case examples showing how the logged data can be used for underground and open pit mine design.

Nov 25, 2010

By I. W. van der Merwe

Recently, a new kind of filtration has emerged, namely nano-filtration (NF). It is a membrane-based process which exhibits totally unique separation characteristics for dissolved salts as well as for many non-charged species. By exploiting the particular separation characteristics of this new membrane type, many unique and novel separations have been made possible. The basis for separation by nanofiltration is the negative surface charge of the membrane. This results in rejection of multivalent anions, whilst associated cations are also rejected to maintain electro-neutrality. This peculiar property enables separation of dissolved ions such as sulphate and copper from acid, whilst the acid may be purified for reuse. This paper aims at providing an overview of the principles of nanofiltration, illustrated by particular examples.

Jan 1, 1998

By Eric Konigsmann

"The Pogo project is located on the Goodpaster River, 38 miles north of Delta Junction in east central Alaska. Sumitomo Metal Mining and Teck Corporation are planning to develop a 2,500 ton per day underground mine and mill at Pogo. A preliminary resource of 5.5 million ounces of gold has been identified in two flat lying lenses. An underground adit has been developed to facilitate underground drilling of the deposit and to provide samples for bench and pilot scale metallurgical testwork.Flowsheet development included the evaluation of several processing options. The final flowsheet selected includes SAGhall mill grinding, gravity concentration with intensive cyanidation and direct electrowinning, sulfide flotation with ultrafine regrinding, and cyanide leaching and CIP gold recovery from the flotation concentrates. Flotation tailings will be filtered for placement in a dry stack storage facility or disposed of as paste backfill underground. All of the CIP tailings will be disposed of underground as paste backfill. A pilot plant was carried out to evaluate the proposed flowsheet described above and to confirm the gravity recovery predictions.Great care was taken in the development of the flowsheet and site layout concepts to mitigate the environmental impact of the proposed operation. An overview of the site water management concepts is presented and the impact of water issues on the process flowsheet is discussed."

Jan 1, 2002

By Helmut Hass, Michael B. Gilbert

The extension of the commuter railway system (S-Bahn) in Leipzig, Germany willrequire the construction of an underground line crossing the downtown area of thecity to tie the Bavarian Station in the South to the Main-Station in the North. The City-Tunnel-Leipzig is currently one of the largest infrastructure projects in Europe. This system extension will have a length of approximately five kilometers. 3.9 kilometers of that length are currently being constructed using either cut & cover construction or tunnelingmethods. The design and construction of this project currently is and will continue facing very significant challenging urban and demanding geotechnical conditions.

Jan 1, 2007

By A. Yu. Lein, V. V. Maslennikov, S. P. Maslennikova, I. Y. u. Melekestseva, Yu. A. Bogdanov

Tellurium is a high-tech and also toxic element. This element shows sufficient contents in Fe-Mn crusts and nodules in the modern ocean to be involved in future industrial processes [Hein et al., 2003]. Tellurium minerals and contents are not well recorded in modern and ancient black smoker systems. Tellurides are rarely found in sulfides from the modern oceans [Iizasa et al. 1992; Maslennikov et al., 2010]. The previous common opinion that tellurium is scarce in active seafloor hydrothermal systems can be revised due to the recent discovery of abundant tellurides in chimneys from Brothers Volcano vent site [Berkenbosch et al., 2012]. We found abundant tellurobismuthite, hessite, and native tellurium in chimneys from Su Su Knoll vents sites (West Pacific). So, tellurides can be found in some chimneys but absent in others. The causes of this are poorly understood. These conflicting data create numerous questions and require an explanation. The problem can be resolved by research at different scales including analysis of relevant genetic features of host sequences, systematic textural and paragenetic studies of different types of chimneys, and their rare mineral assemblages. Paragenetic models, compositional analyses and ranges of tellurium-bearing minerals and the physicochemical interpretation of chimney diversity in different types of VMS deposits are the main subjects of our research. The data on tellurides in chimneys from ancient VMS deposits should also be useful to resolve this problem.

Sep 1, 2014

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.