Search Documents

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Robert C. Freas

While on the surface limestone marketing may appear mundane, it has continued to provide a series of challenges beyond the realm normally envisioned with this industry. This paper presents a case history of a mature and well-established quarry company that has attempted to keep pace with an ever-changing economy. It examines the impact of socio- economic and technological factors on the company's marketing efforts, and looks at the role of both short and long range planning. The realities which have had to be faced and how product requirements have been kept in balance with production restrictions are also discussed.

Jan 1, 1981

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

By John D. Spencer

Surveys to establish the quantity and quality of coals available for metallurgical, industrial, and energy use, investigations to develop better mining methods, and studies aimed at improving the health and safety of those who mine the coal highlighted Bureau of Mines research and technologic work on coal in 1968. Also being developed are more efficient methods of coal preparation, transportation, storage, and utilization. Supplementing this effort are projects designed to assure minimum disturbance of land, water, and air resources. Research centers and laboratories of the Bureau of Mines are listed in appendix A. Publications released during 1968 are cited with the various projects and in appendix C. Organizations that cooperated in the work in various ways are cited in appendix B.

Jan 1, 1969

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

Thermodynamic properties of the solutions of hydrogen in metals and carbon in austenite were investigated and it is possible to predict the interstitial solubility in these systems over relatively wide ranges of temperature and solute activity. Monte Carlo methods were used to compute the arrangements of interstitial atoms on the tetrahedral sites in body centred cubic metals and the octahedral sites in face centred cubic metals. It was shown that the non-configurational entropies of solution of hydrogen in metals can be interpreted as being principally vibrational and on this basis the potential value of the isotopic solubility ratio theory in indicating the compositional variation of these non-configurational entropies was discussed. The need for future work along these lines is pointed out.

Jan 1, 1970

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

General recognition of the potential benefits of utilizing advanced technology has focussed public attention on the organisation of tertiary education. This has produced a situation where opportunities exist for significant changes to be implemented. The challenges to Mining education in this environment of change are analysed with respect to the setting of education objectives, the role of centres of education, course structures and student access to courses. The scope of the analysis includes formal courses for professional education and technical training, and programmes for continuing education and postgraduate research. Previous significant advances in mining technology illustrate the importance of encouraging the establishment of an extensive involvement with mining education. Education cannot be the sole responsibility of professional academic organizations; significant industry participation is essential. Methods of achieving this interaction are discussed. Major changes in techniques available for disseminating information provide a significant incentive to assess the relevance of existing course structures and restrictions on student access to courses. Establishment of a less rigidly progressive system of education is discussed with respect to the development of the full potential of computer based learning. This will expand the availability of mining education to include remote locations. The practical feasibility of such changes and recognition of the value of education as a commercial resource could also increase overseas involvement in Australian mining education. Benefits of such changes and problems that may develop if accreditation systems are not also changed to take account of new technology are outlined.

Jan 1, 1989

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

By David Shatwell

Recent epithermal gold discoveries in Chile and Bolivia provide increasing evidence of a belt of intermittent, epithermal, precious metal mineralization east of the main Andean porphyry copper belt. This relationship may be the result of an easterly decrease in the age of magmatism and erosional levels, in¬crease in depth above the underlying Benioff zone and consequent changes in magma chemistry, or some other unrecognized factor. Examples are: • The Choquelimpie gold-silver mine in Chile and numerous other epithermal prospects (such as La Riviera, Bolivia) in late Tertiary volcanics along the Chile-Bolivia border. These lie east of the belt that contains the Toquepala, Quellaveco and Cuajone porphyries in southern Peru and the Cerro Colorado, Copaquire and Quebrada Blanca porphyries in northern rhila

Jan 1, 1990

Continuous pH and Pulp Potential Measurements During Complex Sulfide Ore Flotation

Sep 13, 2010

By J. P. Bergh

The advent of low-quality export coal demand has brought a new range of possibilities to the South African coal industry. Products that traditionally were only of value to the domestic or combustion industry sectors now have the potential to be exported, with only minor amounts of upgrading required through beneficiation. Comparatively high steam-coal export prices can be obtained for lowquality export coal, which enhances the economic feasibility of expanding low-quality thermal coal exports. There are, however, increasing concerns about the feasibility of lower quality thermal coal exports and the broader implications. These concerns relate to the environmental impact of low-quality thermal coal production for export and the inherent threat to the security of domestic thermal coal supply in South Africa. Against this background, this paper serves to explain the extended value chain in the production of export coal. The technical and economic advantages and disadvantages of low-grade exports versus coal production for domestic use are evaluated. The value chain estimation is calculated by the beneficiation modelling and characterization of two coals. Based on the value estimation, the lowgrade export production scenario, and finally the modelling of potential pollutant distribution, are described. Keywords coal beneficiation, techno-economics, thermal coal, dense medium processing, dry processing, fine coal processing, environmental impact.

Nov 1, 2013

By Gray Mullins

The construction of drilled shafts as well as other cast in place foundation alternatives relies heavily on good practices from the contractor, engineer, and inspector in order to produce a quality foundation element. As many of the installation methods involve blind concreting processes, it is difficult to be certain of an intact concrete mass of the intended dimensions. A new integrity test has been developed that provides additional insight into the integrity of drilled shaft concrete. By measuring the temperature throughout the shaft via standard access tubes, the measured temperature profile can be compared to the normal signature associated with a shaft of the specified size. This article provides an overview of the new method development, test procedure, analysis, and results.

Jan 1, 2010

By M. C. Ruiz, M. E. Godoy, J. B. Rivarola, M. W. Ojeda

The amount of Pd recovered from an exhausted olefin hydrogenation catalyst was found to depend on mixing technique, particle size, carbon percentage, chlorine flow, reaction time and temperature. Pd extraction was total when a sample in the 125-175 micrometre particle size range was chlorinated for 60 min at 723 K with 20 cm3 Cl2/min, for 60 min at 748 K with 30 cm3 Cl2/min and for 30 min at 773 K with 30 cm3 Cl2/min. No C addition was needed; the initial C content of the catalyst was sufficient for total recovery. Pd extraction was also affected by heat treatment in different atmospheres before chlorination. Treatment with O2, N2 and N2 with traces of O2 led to different degrees of oxidation of C and permitted the formation of oxidised Pd species. Thermal pretreatment in N2 with traces of O2 was most conducive to Pd extraction

Jun 21, 1905

By O. C. Blade

Total sales of diesel fuel in the United States continue to Increase. This growth is due primarily to two causes: More conversion to diesel units by the rail-roads In recent years, and the greater use of diesel engines in trucks, busses, and tractors. Following are some figures on the distribution of the fuel computed from data issued by the Bureau of Mines.2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,522,000 barrels during the first six months of 1955,3/ corresponding figure for 1954 was 91,170,000 barrels. Information on the properties of this engine fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1955