Search Documents

By E. M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger miners have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1987

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By S Chew, A Bennett, N Di Giorgio, B Osborne

After relining one of two blast furnaces and enlarging its sinter plant in 2009, BlueScope radically restructured its Port Kembla steelworks operation in 2011, shutting a blast furnace and halving its total production. This drastic move in response to unprecedented raw material prices relative to achievable steel prices was like that of many integrated steelmakers worldwide facing similar challenges. The 2011 restructure also saw major changes in the amount and type of iron ores and ferrous burdens purchased, and a fundamental reappraising of ‘value’ in iron ores. This paper outlines the changes to raw materials purchases from 2011 to 2017, how BlueScope has responded to the changes in pricing and raw materials quality, the effect on the sintering and blast furnace processes at Port Kembla resulting from higher gangue content, some of the broad technical and economic challenges faced by steelmakers confronted with lower quality iron ores and how BlueScope is meeting those challenges.CITATION:Di Giorgio, N, Bennett, A, Osborne, B and Chew, S, 2017. Recent Port Kembla experience with iron ore use – sintering and blast furnace, in Proceedings Iron Ore 2017, pp 25–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By Clarke DS

The igneous intrusions in SE Papua New Guinea are part of a sub-volcanic to plutonic, high-K calc-alkaline to shoshonitic suite. High-K andesitic to dacitic intrusives on Misima and Woodlark Islands, and shoshonitic intrusives in Milne Bay and the eastern Owen Stanley Ranges are related to late Cenozoic andesitic volcanism. Both suites are associated with epithermal Au-Ag deposits and weak porphyry Cu-Au mineralisation. All significant alluvial and lode gold occurrences in the region are spatially related to intrusions. Intrusions in the D'Entrecasteaux Islands and near Mt Suckling are core plutons related to basement doming, and appear to have no association with either volcanism or hydrothermal mineralisation. The core plutons are not petrochemi:ally distinct from the volcano-re:-ed Intrusions.

Jan 1, 1991

By André C. Zingano

The coal pillars in room-and-pillar mining method are subjected to vertical stress due to overburden rock mass and horizontal stress relieve due to entries excavation around them. Some coal mining companies are applying rock bolts and steel straps to improve the pillar strength, consequently to reducing the pillar size and increasing coal recovery. This kind of approach deserves some discussion, whether it is pillar reinforcement or just rib support. The efficiency of pillar reinforcement (or rib support) is directly related to the initial load capacity of coal pillar, the type of excavation, and the width to high ratio of the pillar. The objective of this paper is to understand the mechanism of pillar reinforcement (or rib support) using rock bolts and steel straps on pillar ribs. Numerical simulation taking into account the relations listed above. The results showed that the increase of coal pillar strength is very short, and there is no influence on improvement of load capacity of pillar. However, the rib support avoids block falling, rib failure, and displacement, reducing the pillar failure propagation into the pillar center. Keywords: coal, pillar reinforcement, room and pillar.

Jan 1, 2006

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields' South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

By John C. Machisak

INJURY experience and employment data at all metal mines in the United States and Alaska are presented in this Information Circular for the calendar year 1958. This publication covers the metal mining industries, and contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. These operations report injury and employment information annually to the Bureau of Mines on a voluntary basis. The Bureau is authorized to make requests for such data, and the information submitted contributes immeasurably to the promotion of safety in the metal mining industry. Every effort has been made to make the annual canvass as complete as possible. This publication contains, along with production and development workers, the office employees at the mine location. The metal mines identified in this publication are classified according to the mineral ores mined; that is, copper, iron, lead-zinc, gold-silver lode, gold placer, and miscellaneous metals.

Jan 1, 1962

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Paul S. Goodman

Volume II The purpose of this study is to explain reasons for the productivity differences in mining crews. The literature on group productivity is examined. Then a new approach to estimating productivity differences is proposed and estimated across seven different mines. The results indicate a fairly robust model in terms of explanatory power. Recommendations on how the model can be used as a managerial tool are presented.

Jan 1, 1985

By Jennifer Ward

The primary objective of this paper is to establish how a low cost, high definition (HD) camera can allow for easy sustainable recordings of blasting operations. The subsequent analysis of each video can be utilized to monitor what type of performance was achieved and aids in improving blasting performance.

Jan 1, 2015

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921

By D. Laguitton, D. Hodouin, V. K. Gupta, R. Spring

"The CANMET SPOC project aims at inducing progress in process evaluation and optimization by developing user oriented software based on state-of-the-art theory. The present work is the result of a joint effort by CANMET, Noranda Mines and Université Laval to develop two computer packages: one (RTD) to calculate the residence time distribution that best describes the material transport through the mill, the other (FINDBS) to estimate the rate of breakage and distribution function of the population balance model in a ball mill. The RTD package can handle data from various experimental methods (impulse or complex tracer feed, with or without recycling, etc...). The FINDBS package provides options for the functional description oj both model parameters Band S. The full detail of the methods and programs appears in a users guide. The program capabilities and several sample runs are presented.IntroductionSimulation of mineral dressing operations by computer has been largely contained within academic and research circles and has not yet gained a status of routine practice in the ore and coal industries. It is however a matter of time before process simulators are available on every process engineer's desk to assist process optimization tasks, flowsheet design and professional training. The CANMET SPOC project (Simulated Processing of Ore and Coal) was initiated in 1980 to assist the Canadian industry in integrating computer-based methodology for process evaluation and optimization(1). Software development, documentation and transfer is one of the main priorities of the project which will mature in 1985 by releasing a complete package of manuals and programs covering sampling, material balance computation, unit modelling, flowsheet simulation and optimization . This paper is a condensed description of a typical project element in its 1982-1983 state of development. The required methodology for ball-mill modelling and simulation was consolidated an d merged to other project elements during a joint study under contract financed by CANMET and Noranda Mines Ltd . The first part of the study dealt with documenting experimental methods and software for ball-mill computer simulation. Université Laval GRAAIM (Goupe de Recherche en Automatistion Appliquée à l'Industrie Minérale) acted as sub-contractor for this part of the study(16,17). A second part dealt with applying the model calibration techniques to a large industrial data base and is reported elsewhere(2,18,19)."

Jan 1, 1984

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009