Search Documents

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By Y Öztas, S McKinley, T Baker

The Kisladag Mine, Turkey, is a large porphyry gold deposit which is mined by open pit methods. In operation for over ten years, Kisladag provides an excellent example of how attention to a geologic feature, namely hydrothermal alteration, became a very effective predictive geological tool for planning and operation. The alteration domains were initially used as a geological tool to assist with establishment of resource model domains and to guide delineation drilling, but they were soon recognised to be correlative to geotechnical characteristics (affecting pit slope angles) and metallurgical performance (heap leach recoveries). Recent developments in spectral processing allow the systematic quantification of complex overlapping alteration phases and have greatly improved the ability to rapidly define internally consistent alteration domains for geotechnical and geometallurgical purposes.Alteration at Kisladag comprises a central core potassic (K-feldspar-biotite) zone, a tourmaline-white mica enveloping zone, an advanced argillic lithocap on the deposit’s eastern side and an overprinting pervasive argillic zone. These alteration zones and their distribution were based initially on strictly qualitative, visual mineralogical logging of diamond drill core. With the need for more accurate and consistent identification of the alteration mineral suites, particularly the phyllosilicate phases, logging was augmented by systematic measurement of spectral data using a Terraspec instrument.Recently the Kisladag spectral database (over 85 000 readings) was reprocessed by the newly developed methodology (aiSIRIS™) that allows relative quantification of the spectrally-responsive minerals. Visualising this transformed spectral mineralogy at various mineral concentration thresholds using implicit modelling software (Leapfrog®) led to the creation of consistent mineralogical and alteration domains that are used for the definition of geotechnical and geometallurgical parameters. An implicit modelling workflow enables these domains to be easily updated as new data is collected while maintaining geological integrity of the model.CITATION:McKinley, S, Baker, T and Öztas, Y, 2017. Alteration at Kisladag gold mine, Turkey – a progressive study in geology, geotechnics and geometallurgy, in Proceedings Tenth International Mining Geology Conference 2017, pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Edward M. Dowey

The concrete lining for a long 8.05 km (5 mi) section of New York City Water Tunnel No. 3 was cast in place. The contractor, Grow-Perini-Skanska, placed over76,841 m3 (100,505 cy) of concrete, pouring 24 hours per day, 5 days per week. The concrete was dropped 204 m (670 ft) to the tunnel level, transported by rail to a concrete remixer and pump, and placed in 146.3m (480 ft) of full circle forms. Some of the many challenges include the sheer magnitude of the job, navigating through drifts, a raise and curves, dealing with ground water inflows, and placing the concrete within time limits.

Jan 1, 2001

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By M. T. Baquera

A comparison of microstructures associated with W single-crystal ([001], [011], [111]) rods prior to deformation (as grown), and after quasi-static compression (at a strain rate of ~1/s) by transmission electron microscopy (TEM) shows several orders of magnitude difference in dislocation density. Dislocation substructures were not significantly different amongst the deformed sample orientations. In contrast, [001] W rods penetrated into steel targets, at impact velocities of ~1.3 km/s, exhibited heavy dislocation densities and dynamic recrystallization as very distinct microstructural regimes accommodating the penetration process. Twinning on {112} also occurred as a precursor to, or remnant of, these microstructures near the projectile head. These results suggest that deformation accommodating the extreme strains and strain rates associated with the penetration of a single-crystal rod into a metal target is not adequately represented by conventional deformation

Jan 1, 2006

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By Shane Baker

Cementation Foundations Skanska Ltd encountered many significant challenges in designing and constructing the foundations for the LNG (Liquefied Natural Gas) tanks and associated structures at the Isle of Grain, Kent, UK. With LNG cargo ship levels fixed by the adjacent English Channel, the platform could not exceed critical thickness in order to achieve final grade level, so a safe and efficient working platform for construction equipment on extremely poor alluvial soils was designed and installed. The detailed pile design also required particular analysis of the pile group behaviour and considered seismic load cases not usually associated with UK pile design. Continuous flight auger (CFA) piles were the chosen foundation solution and design was verified through preliminary and working pile tests both axially and horizontally. Contaminated land and existing foundations from a previous oil terminal meant that removal of spoil was extremely costly so specific measures were taken to minimise the off-site disposal. The management of a package of general Civil Engineering in addition to the piling scope, coupled with an unrelenting production program has forced a raising of the bar for this foundation technique.

Jan 1, 2006

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968

By Mohammed Sakr

The use of helical piles as a deep foundation option has considerably increased in the recent years to support a variety of loads, from small loads for several applications such as residential housing, solar farms, utilities and retrofit projects, to large loads for many applications such as commercial, power transmission lines, oil facilities and industrial applications. Therefore, it is necessary to qualify and quantify their axial capacities and performance characteristics. This paper presents the first full-scale axial compression and tension (uplift) testing program executed on large capacity helical piles installed in cohesionless soils. A total of eleven pile load tests using either single or double-helix piles with shaft diameters that varied between 324 mm to 508 mm (12¾ in to 20 in) were carried out, including seven axial compression tests and four tension (uplift) tests. The results of the axial compressive and tensile pile load tests as well as field monitoring data of helical piles installed in dense sand are presented in this paper. Based on the results of this study it was found that helical piles have developed significant resistance to axial compressive loads up to about 2920 kN (656 kips) and tensile loads up to 2900 kN (652 kips).

Jan 1, 2011

By Z. Y. Ding

This paper emphasize two points in piled wharf design which are important than structure calculation. First, during design of piled wharf on soft stratum, the bank slope stability is the first important item. Second, the live load, the backfill and the original ground's settlement will influence the wharf structure causes cracks. Two practical examples were illustrated.

Jan 1, 1991

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

The ore, as sent to the sulphide mill, is a mixture, in varying proportions, of oxidized ore from above the 450-ft. level and sulphide ore from above and below (to date mainly from above) that level. The oxidized ore consists essentially of quartz, with varying amounts of kaolin and clayey material which passes into the slime and, in excess, creates a serious problem in settling. Pyrite may be present in small amounts. The gold is free and extremely fine.The ore, classed as sulphide, consists of pyritic material in a quartz gangue. The sulphides have been exposed to weathering, leaching by descending solutions and attack by ascending gases and actual burning. The alteration products occur in widely varying proportions and this variation adds to the difficulties in settling and control of grinding and flotation.Copper Minerals.-Chalcopyrite is the principal copperbearing mineral with smaller and varying amounts of covellite, which is sometimes associated with chalcocite, both these minerals being apparently of secondary origin.Examination of tailing by Dr. Stillwell has revealed all stages between clean chalcopyrite, chalcopyrite tinged with covellite, covellite with residual cores of chalcopyrite and clean covellite.The chalcopyrite is free floating, very few particles of clean chalcopyrite being observed in the tailing from granular flotation. The chief tailing loss is probably as chalcopyrite occurring as small inclusions in pyrite...

Jan 1, 1939

By J. Hunter, E. Jackson

This paper describes work done by Placer Dome Technical Services Limited, a subsidiary of Barrick Gold, and Nautilus Minerals Inc. in support of the conceptual design of a subsea mining system. It describes an overall concept design plus specific studies into mechanical excavation at depth. The concept design includes one or more subsea excavators connected to a suction riser, which transports the cut material to a shipboard dewatering and offloading system. A multi-phase investigation was performed into the mechanical excavation of seafloor massive sulphides at depths of around 1600m. Rock samples were recovered and tested for rock properties and cutting behaviour. A small pick drum cutter was procured and tested on a representative concrete slab in a lab and tested again while submerged in a test tank. Finally the cutter was tested on a massive sulphide ore body at 1600m depth. The cutting performance results, e.g. pick forces and specific energies, should provide valuable input to the design of future full scale subsea mining systems.

Jan 1, 2007

By Paul. E. Pesonen

Since early in 1940 the Bureau of Mines has been concerned with possible means of utilizing manganese-bearing materials from the Missouri Valley manganese deposit. During the period between July 1945 and August 1947, the Bureau of Mines undertook to complete certain phases of the problem by re-evaluating the results of earlier work and supplementing the findings by additional operations and field studies considered necessary to permit drawing of final conclusions. Distinctive discoloration marks the outcrop of the manganese deposit which is exposed on both flanks of the Missouri River Valley and its major tributaries for a peripheral distance of approximately 523 miles in south-central South Dakota. The apparent magnitude of the deposit, judged largely from observation of the outcrop, had led to much speculation as to its actual value in terms of tonnage and grade. Similarly, investigative work aimed at developing a means of winning a usable manganese-rich product from the deposit had reached no conclusion, except that certain methods showed more promise than others for accomplishing the final objective.

Jan 1, 1948

By Servant S

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the scope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the scope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this Mine.

Jan 1, 1998

By A. Nel

The gold mining industry in South Africa stands to benefit much from the implementation of the self-directed work team concept. Its introduction implies flatter hierarchical structures, empowerment of the workforce and increased participation. Research indicates that half of the initiatives to implement self-directed work teams, however, fail, and it is therefore imperative for companies to be aware of the factors impacting on the effectiveness of self-directed work teams in order to focus on these early in the implementation phase. The objective of the study was to qualitatively determine these factors. Semi-structured interviews based on the phenomenological method were carried out. The sample included members of, and individuals involved with, self-directed work teams (N= 26) from a large gold mining company in South Africa. Results show that most respondents rated the availability of resources to do their work as the most important factor affecting their effectiveness.

Jan 1, 2006

By S C. Dominy

Various styles of gold mineralisation pose problems during sampling because of their complex gold grade distribution and presence of coarse gold. Effective sampling and sample preparation forms the basis of resource estimates. The design of a sampling and assaying protocol must be based on a thorough understanding of the mineralisation in question, which should include consideration of gold particle size and mass distribution. The proportion of coarse gold within samples has a profound effect on the requirements for sample preparation and assaying. Choice of preparation procedure and assay type is of critical importance if sampling errors are to be minimised. Traditional fire assays, using small charge sizes, often understate assays gained from large charge sizes and techniques such as screen fire assay and LeachWELL. Proper application of the Theory of Sampling reduces errors during collection, preparation and assaying. A quality control/quality assurance program must be implemented and critically assessed. A case study from the Ballarat mine is presented, which is characterised by substantial quantities of coarse-gold hosted in quartz veins. Diamond core drilling is the key input into resource delineation. A number of different sampling and assay options have been trialled over the recent project history. The current sampling protocol utilises whole drill core, using LeachWELL assays after logging and photography.CITATION:Dominy, S C, 2017. Sampling coarse gold-bearing mineralisation – developing effective protocols and a case study from the Ballarat mine, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 71–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The following brief observations on the mineral composition of the Mt. Oxide copper ore are intended to supplement the geological description of that ore-body recently published by Blanchard (2).'" The Mt. Oxide copper mine is situated about 45 miles W.N.W. of Dobbyn, in the Cloncurry district of Queensland (Fig. 1). A representative suite of specimens from the mine was obtained through the kindness of Mr. P. B. Nye, Executive Officer of the Aerial, Geological and Geophysical Survey of Northern Australia, and Mr. Jack Hall, the tributor of the Mt. Oxide mine. The specimens, as shown in Fig. 2, were nearly all from the sulphide zone, between the l04-ft. level and the 300-ft. level. Several additional specimens, together with information which will be referred to later were kindly sent to me by Mr. Roland Blanchard.MINERAL COMPOSITION OF THE COPPER OREThe mineral composition of the ore is relatively simple. It consists essentially of chalcocite, with varying, but minor figures...

Jan 1, 1940

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011