Search Documents

Planning for the Macraes Extension project highlighted the need for additional tailings storage availability. The possible solution of developing new tailings impoundments in Northern Gully, in tum, led to concerns being expressed by the regUlatory authority over the assimilative capacity of Deepdell Creek. Philosophical differences over the appropriateness of applying a seepage model used to set standards in consents for the original project resulted in the company re-evaluating the whole monitoring system associated with tailings disposal and seepage control. Re-evaluation indicated problems arising from the existing in-stream water quality monitoring in respect of protection of the aquatic ecological system and verifiability of results. A new monitoring system was designed relocating the compliance monitoring point out of the stream and into the gully containing the tailings impoundments giving greater certainty of monitoring results to all parties and providing improved protection for the aquatic ecology of Deepdell Creek.

Jan 1, 1993

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By Jacques J. Eksteen

Any effort to improve the metallurgical control of industrial furnaces employed in the primary extraction of high carbon ferroalloys are bound to fail unless the variability of the melt is not fully accounted for. A number of sampling campaigns were performed on both 3phase AC submerged arc and single phase DC open arc furnaces at different smelter sites in South Africa where High Carbon Ferrochrome is produced. It was found that the heterogeneity between multiple samples during a single taps were much higher that for heterogeneity found within a sample. Moreover, this heterogeneity (as quantified by the relative standard deviation per tap) varied with the operating conditions of the furnace, the element monitored and the type of furnace. A relationship was found between the relative standard deviation of certain elements and the degree of subcooling of the melt.

Jan 1, 2006

By G. A. Kosick, G. S. Dobby, O. Matwijenko

"A 100 kg/hr portable flotation pilot plant has been operated at Kidd Creek Mines with the objectives of:(a) determining performance expected by column flotation circuits on primary zinc and copper cleaning, and (b) evaluating column flotation circuit configurations.The self-supporting pilot plant, owned by Minnovex Technologies Inc. and operated by Minnovex and the University of Toronto, consisted of three 16 cm diameter by 6.5 m high columns and a bank of four Denver No. 7 cells. It was configurable to any arrangement using these four (or fewer) units. The columns were controlled through the use of multiple pressure transducer measurements. This paper presents the approach to testing and the results of more than 70 circuit tests. INTRODUCTIONThe integration and retrofitting of flotation columns within existing mechanical cell flotation circuits is becoming a common occurrence. The correct approach to this integration, however, is often difficult to define, due to a scarcity of previous experience and the difficulty in predicting column circuit performance. In most cases, the effect of column implementation has been experimentally assessed using a single pilot column, with the consequence that selection of an appropriate circuit to implement is difficult. Important considerations are the impact that column water addition will have on the existing operations, and the differences between mechanical cell and column performance in integrated cleaning circuits.To address the problem of circuit selection a portable flotation pilot plant, consisting of both columns and mechanical cells, was designed and constructed by Minnovex Technologies. The pilot plant was structured for complete flexibility of circuit configuration, with the intent to provide a means by which both research and plant personnel could determine the best possible column circuit configuration for a given application."

Jan 1, 1990

Analysis of Electrostatic Separation for Rutile Cleaning Duty Using a Plate Electrode Assisted High Tension Roll Separator A plate assisted electrostatic high tension roll separator has been used for the removal of impurity mineral grains from a rutile rich product stream. A laboratory study and a subsequent production study explored the effect of machine conditions with a view to the optimisation of the separation performance of the separator. The performance requirement was that the TiO2 grade in the non-conductor stream was to be less than ten per cent whilst at the same time the ZrO2 grade in the conductor stream had to be less than 0.5 per cent at mass recoveries of greater than 90 per cent to the conductor stream and less than 5 per cent to the non-conductor stream. Mineralogy data was utilized to determine the feasibility of achieving the production targets with the feed under study. Since the feed stream mineralogy was dominated by rutile, leucoxene and zircon, it was possible to use an approximation to the actual mineral assemblage as well as the raw X-ray fluorescence data to understand the separation duty of the Carrara machine. Since there were four conflicting criteria used for the performance requirement, an index was devised that incorporated all the requirements simultaneously. This new index was the sum of the squares of the difference between the achieved and desired values, weighted with respect to the variance of each variable. If the desired value for a particular criterion had been met its contribution to the sum was set to zero, no matter how well the criterion had been met. For the production machine the strict requirements were almost achieved. As expected, the achievement of the target performance was dependent of the feed conditions at the time of measurement. This paper reports the results of this study.

Sep 13, 2010

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

The safety of mining operations is significantly influenced by the in situ stress fields in which the mining excavations are created. From the point of view of planning of mining operations, the in situ stress field is a most important input parameter for valid modelling of excavations. Many in situ stress measurements have been carried out for mining and civil engineering projects in southern Africa over the past 30 to 40 years. A database of in situ stress measurement results and observations has been compiled. This paper presents results extracted from the database which are considered to be of particular interest to mining areas in South Africa. The database will permit the estimation of likely stress conditions in new areas of mining, provide a basis for evaluation of results from future in situ stress measurement programmes, provide a basis for comparison of observed behaviour with expected behaviour, and provide a source of data on which realistic design and layout analyses can be based. The information contained in the database indicates that horizontal to vertical stress ratios in the Carletonville, Klerksdorp and Rustenburg areas are significantly higher than the value of 0,5which is commonly used in mine layout planning.

Jan 1, 1998

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008

By T. Lenarcic, R. Svrkota, J. M. McNeal, E. Prohic, S. Pirc

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Surface drainage samples, the usual media employed in mapping national territories, cannot be used for the geochemical mapping of carbonate terrains because there is no regular surface-drainage pattern on karst. Suitable sampling media have been studied in Yugoslavia, one-third of which consists of karst terrain. Sampling designs for the work were based on analysis of variance techniques. During initial investigations of various sampling materials in NW Yugoslavia sediment and aquatic moss from karst springs, along with soil, were established as the most appropriate media. Modified sampling procedures were then carefully applied along the entire Yugoslav karst belt, which includes terrains of contrasting topography, climate, pedology and vegetation. The studies indicate that climate and relief do not systematically influence the geochemical composition of soil. Regional and local variability was assessed for 21 chemical elements and the feasibility of producing stable regional geochemical maps was determined for a number of elements on the basis of sampling aquatic moss and sediment from karst springs and soil

Jul 1, 1991

By H Saw, M Cordova

Cemented rock fill (CRF) is often used to support open stope voids. This allows for the full recovery of ore while achieving global mine stability. In such cases, the exposed CRF masses require adequate compressive strength and stiffness to resist the forces and limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or development mining waste. This means that conventional laboratory samples cannot be readily used to determine the laboratory strength. Consequently, a research project was undertaken to determine the influence of sample size on uniaxial compressive strength. This paper presents the results from CRF samples that were prepared using the same mix design and then cast into moulds with diameters of 150, 240, 300 and 400 mm. The laboratory testing also allowed a better understanding of the effect of particle size distribution upon the overall strength of a rock fill mass. The laboratory results were compared to a database of large-scale results from the testing of fill masses from a number of mine sites.CITATION:Cordova, M, Saw, H and Villaescusa, E, 2016. Laboratory testing of cemented rock fill for open stope support, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By William H. Pomroy

Fire on surface mining equipment is a serious hazard to life and property. The Bureau of Mines, through a program of contract and in-house research, has developed and in-mine demonstrated reasonably priced, reliable automatic fire protection systems to deal with this problem. This report reviews the development and subsequent testing of systems for haulage trucks, front end loaders, coal augers, dozers, drills, and shovels. A variety of fire sensors, extinguishing agents, and control systems arc discussed in the context of mine equipment designs and operating environments

Jan 1, 1980

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By H Zhou, T Honeyands, M Zhou

In iron ore sintering, packing the granules onto the sintering strand to form a porous bed with optimum permeability is a complex dynamic process. The packed bed voidage is the key factor determining the flame front speed and the final sinter productivity and quality. Previous studies have found that granules are soft quasi-particles with a typical structure of nuclei with an adhering fines layer. The deformation of the adhering layer greatly affects the bed voidage during packing, which is related to the strength of the adhering layer and the force exerted on the granules. In this study, tablets simulating the particle size distribution in the adhering layer of granules were made for four single ore blends. Both the tensile strength and shear strength properties of these tablets were investigated as a function of water content by the uniaxial compression test and direct shear test respectively. The results of compression tests show that the adhering layer becomes weaker and more compliant with the increase of moisture. The most porous ore has a more rigid adhering layer than the other three tested iron ores at any given moisture content. In direct shear tests, the internal friction angle of the adhering layer ranged from 31° to 37° and varied little with the moisture content or ore type. The cohesion constant is around 1 kPa and is quite small compared to the stress applied to the granules during packing. Combined with the results of granulation and packing experiments, the influence of the adhering fines layer deformation on the degree of voidage loss is specifically discussed.CITATION:Zhou, M, Zhou, H and Honeyands, T, 2017. Tensile strength and shear strength properties of the adhering layer of granules in iron ore sintering, in Proceedings Iron Ore 2017, pp 117–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

The Coeur Rochester Mine is one of the largest and lowest cost primary silver mines in the United States. In January, the mine surpassed 3.1 kt (100 million oz) of historic silver production. Rochester is owned and operated by Coeur d’Alene Mines, the world’s largest primary silver producer. Rochester is the world’s seventh largest silver mine. It also produces gold — more than 31.1 t (1 million oz) in historic production. Cash operating costs have averaged 8 cents/g ($2.58/oz) of silver since operations began in 1986.

Jan 1, 2004

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008