Search Documents

By David Smith, Bernie Martin

The Queens Bored Tunnels consist of 11,000 feet of 19'-6" inside diameter tunnels mined through rock, mixed face and dense glacial till, constructed with bolted gasketed one pass reinforced concrete liner. The tunnels are to be excavated with a pressurized face TBM, either EPB or slurry. The construction of the tunnels will require ground stabilization in the mixed face area, instrumentation and monitoring of railway infrastructure, underpinning of bridges, relocation and protection of utilities, demolition of some industrial buildings, construction of open-cut approach tunnels and emergency exits and vent plants. The purpose of this paper is to describe the scope of work, the suggested methodology and the proposed construction schedule.

Jan 1, 2005

By Steve Dubnewych, Jon Kaneshiro, Calvin Jin

The Joint Water Pollution Control Plant (JWPCP), operated by the Sanitation Districts of Los Angeles County (the Districts), treats wastewater generated by over3 million people and processes wastewater solids generated by over 5 million people. The JWPCP Tunnel and Ocean Outfall Project, if constructed, would be one of the major marine outfall projects in the world. The new tunnel and ocean outfall system would provide relief to the existing outfall and allow inspection, maintenance, and repair of the existing tunnel and outfall system, portions of which were constructed as early as the 1930s. Geologic conditions are challenging along the alignments within the study are a being considered. Conditions include saturated alluvial soils, weak sedimentary rock, mixed face conditions, and squeezing ground conditions. Other significant challenges include the potentials for encountering up to 11 bars of water pressure, crossing seismically active faults, and encountering gassy and contaminated ground conditions. This paper discusses the details of the proposed project and the associated challenges.

Jan 1, 2007

A detailed study of the capital investment and production cost for copper electrowinning plants shows that significant savings in both can be achieved by increasing the current density. From the economic analysis it is determined that the optimum current density which will result in lowest capital investment and lowest operating cost is between 60 A/sq. ft. and 70 A/sq. ft., or at least three times as high as the Conventionally employed current density. The specific investment, expressed as $/ton-year, is found to be a function of both the current density and plant capacity and has a minimum value at the optimum current density. Empirical equations are developed for the purpose of estimating the capital investment and operating cost for plants of any production capacity operating at any current density.

Jan 1, 1972

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

In the 1980s and?90s the gold mining industry in South Africa came under pressure from the continued poor dollar gold price and escalating Rand based costs, furthermore the external impacts on the industry were changing. Thus, the Chamber of Mines (COM) shifted its focus away from many historical areas of support towards the new industry challenges in safety and health, labour markets, environmental responsibility, mineral rights legislation and social responsibility. During 1997 the lack of funds and the changes facing the tertiary institutions were often subjects of discussion at the various sub-committee meetings. The Metallurgical Sub-committee of the Chamber Education Fund or the Sub-committee of Consulting Metallurgists as it was known identified the need for the funding structure to change with the times. Up to this time the Chamber of Mines operated an Education Fund that supported mining industry academic departments at various South African tertiary institutions; these funds were derived exclusively from the country?s gold and coal mines the basis of Chamber membership. Funds of less than R5 million per annum were available for distribution by the three disciplinary sub-committees of mining, metallurgy and geology.

Jan 1, 2003

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

In redesigning the cyanide plant at Mount Torrens, in conjunction with Mr. L. W. Grayson, the manager, several minor alterations were introduced in order to have the operations under thorough control, and these having proved serviceable may be of sufficient interest to merit a description here. The lixiviation vats, though only 8 feet in diameter, were retained, but the pipes leading away from the bottom were reduced from two inches to half-an-inch in diameter, and had a fall to the zinc boxes of about 4 feet. As these small pipes were completely filled by the solutions fiowing away from the vats, they exerted a suction equal to their fall and thus hastened the rate of flow, so that tailings containing a larger proportion of slimes could be treated than was possible where the larger pipes were used, as, there not being sufficient fiow of solution to keep the latter filled, no suction could be obtained with them. It was found that with'most of the tailings treated a sufficient flow could be obtained from the half-inch pipes when the taps on, them were only one-third to half open. The lower end of each of these pipes was connected by means on indiarubber tubing with the sille hole of 11 in aspirator bottle, and to the mouth of this bottle a few feet of similar tubing was connected, so that the solutions coming through could be directed into either of the fixed tubes leading respectively to the waste water tank the strong solution zinc boxes or the weak solution zinc boxes.In working the vats, the following method was found to give good results. While filling the vats with tailings the taps were left open, so that the water might drain off into the waste water tank the surface of the tailings was carefully levelled. When the strong solution was run in at the top, the air contained in the interstices of the tailings was forced through the half-inch pipe at the bottom as a strong blast, instead of, as I believe js usual, escaping by means of channels formed by it through the tailings, and thus tending, it would appeal, to render the disposition of the tailings less even and to make.

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

Grouting is mainly used to improve mechanical properties or decrease the permeability of rock mass around civil and mining projects. The purpose of this paper is to present the most effective factors on grout penetration depth in rock mass. Such factors are essential for reliable estimation of the grout penetration depth and the expense for cement take of any grouting project. In this paper, about 50 different types of the relations presented so far by various researchers to estimate the depth of penetration in fractured rock were studied. The effective factors are classified to rock mass properties, grout properties, and operational factors. Results show that firstly, the discontinuities aperture and Lugeon value are respectively the most investigated factors of rock mass properties influencing on penetration depth. Secondly, the yielding stress, viscosity, and density of grout are the most effective factors of grout properties. Finally, grouting pressure has an intense effect among other operational factors. The investigations were also verified in Siah Bishe dam case study. Keyword: grout penetration depth, rock mass properties, grout properties, operational factors.

Feb 27, 2013

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

Blasts should be designed so as to maximise the percentage of charges which shoot to a free face (Le, to a pronounced rock/air interface).Free faces should be rough, parallel and reasonably near to blastholes and, very importantly, concavely·biplanar relative to the charges (see Fig. 6b). The presence of biplanar free faces requires that each charge fragments and detaches its quota of the burden rock before the detonation of:1. later-firing adjacent charges in single-row blasts, and2. dependent charges in multi-row blasts.In multi-row blasts, biplanar faces are best achieved:1. by drilling blastholes on equilateral triangular grids,2. by selecting a VI, V2 or V3 initiation sequence, and3. by using down-the-hole delays.Biplanar faces start to be created only when the conventional value of effective blasthole spacing/effective burden distance (Se/Be) increases beyond about 2.4. Values of Se/Be less than about 2.4 result in planar free faces. Where biplanar faces are created, conventional values of Se/Be are invalid and appreciably greater than real values of Se/Be.

Jan 1, 1986

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

Over half of the molten aluminium produced at the 52,000 tons/ year eapacity plant operated by Comalco Aluminium (Bell Bay) Limited in Tasmania is cast into saleable produets by the direct chill process. Considering the importance of direct chill casting to the aluminium industry it is surprising that so little published literature on the subject is available, although Easton (1947), Smart (1954), and Uppert (1940, 1944, 1945) have contributed much toward lifting the veil of secrecy surrounding the process.The direct chill, or D.C. process as it is commonly called when related to aluminium, consists basically of feeding molten aluminium or its alloys into; water-cooled mould from the bottom of which solid aluminium is continuously extracted. Although the casting procedure is continuous in principle, the equipment is normally operated in an intermittent manner. Castings up to 20 ft long are formed during a cycle. At the end of the cycle casting is stopped and the pit into which thc castings are dropped is cleared before a new cycle commences. Depending on the size of the casting in relation to the cross sectional area of the pit and the support mechanism (commonly a hydraulic ram), 'drops' of up to 15 tons are not uncommon. This method of D.C. casting IS termed vertical D.C. casting and is the one most commonly employed in the aluminium industry.Horizontal casting has come more to the fore in recent years with the casting being extracted from the mould in the horizontal plane and is a truly continuous casting method since flying saws can be simply used to cut the continuously cast shape into required lengths as it emerges from the mould...

Jan 1, 1967

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.