Search Documents

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By Ann M. Hagni

Electric arc furnace (EAF) dust from the secondary steel industry contains lead, cadmium, and chromium that causes it to be classified as a hazardous waste. Pyrometallurgical treatment of EAF dust is directed at recovering zinc and simultaneously rendering the dust non-hazardous. The mineralogy of the EAF dust is important in determining the occurrence and phase relationships of the zinc, lead, cadmium, and chromium contents. The principle phases in EAF dust as determined by reflected light microscopy, SEM-EDS, and XRD are solid solutions of the iron spinels (franklinite, magnetite, and jacobsite), zincite, hematite, and Ca-Fe-Si glass. Chromium is present in small amounts in solid solution in the spinels. Cyclone sizing of the minus 53 pm particles shows that more than 50% of this size fraction are less than 10 pm in diameter. The <I0 pm particles contain zinc as both franklinite in solid solution with magnetite and jacobsite, and zincite as determined by transmission electron microscopy and XRD. Auger electron spectroscopy did not detect coatings of volatile phases on the surfaces of EAF dust particles.

Jan 1, 1994

By Wenbo Luo, Jilai Xue, Tiepeng Li, Jun Zhu

Sodium silicate solutions for producing silica have been ultrasound treated to enhance the precipitation process in laboratory scale. Higher precipitation rate was found with ultrasound treated solutions than those without ultrasound. The obtained SiO2 powder products were characterized using XRD, SEM, BET and laser particle size analyzer. The particle size distribution and the specific surface area of the powder products varied with the power input level and the processing time of the ultrasonic treatment. The results indicate that the efficiency of the precipitation process can be improved optimally when the ultrasound is conducted into the solutions before the nucleation stage.

Jan 1, 2015

By Manabu lshimaru

Solid-liquid interfaces as well as defect formation processes during crystallization of melted silicon (Si) have been examined by using molecular-dynamics (MD) simulations. The ordinary Langevin equation employing the Tersoff interatomic potential was used for the calculation of the atomic trajectories. A solid-melt interface has a tendency to form {]] I} microfacets during the crystal growth in the [001] direction, while it is essentially flat during the (Ill) crystallization. Because of the difference of the interfacial structures, the structures of grown-in defects and defect evolution depend strongly on the growth direction. We discuss defect structures and their formation processes within the context of our results as well as previous experimental observations.

Jan 1, 2001

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By Kosei Morita, Osamu Nakano, Katsuhiko Nagai, Kazuhiro Mori

"The Sumitomo Toyo Smelter and Refinery commenced its operation in 1971 with three Peirce- Smith (PS) converters. “2 hot – 1 blowing” operation was practiced, that is one of two available converters was blowing and the other was standby in a hot state while the third converter was under repair. After several improvements, the stack time ratio reached around 90%; and processing 5 batches a day became possible.As a result of the expansion program of the Toyo smelter and refinery that started in 2001, the converter operation pattern was shifted from “2 hot – 1 blowing” to “2 hot – 2 blowing” with the installation of second converter blowers and an additional ladle crane.In 2005 a, the fourth converter was installed and “3 hot – 2 blowing” operation began. Also, with improvements experienced in the anode furnaces and the anode-casting wheel operation, today, the number of cycles has been increased up to more than 8.5 a day.The treatment techniques of fugitive gas containing sulfur dioxide from converter furnaces have been gradually reinforced, and the fixation rate of treated sulfur is currently being maintained at more than 99.9%. This paper introduces the operations described above, and the improvements in environmental management techniques for the Toyo PS converter operation."

Jan 1, 2009

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By C. M. Acuna

Scarcity of high grade copper low impurity content ores is a reality and processing of low grade dirty concentrates is a need. In spite of this fact, innovative strategies have to be looked at to comply with day to day more stringent environmental regulations. From this perspective the production of matte grades over 70% in copper presents several merits, but it must be contrasted with the fractional distribution of impurities reporting to the condensed phases. Converting of white metal high in arsenic content results in moderate fraction of arsenic to gas, but high deportment to blister. Therefore, production of anode copper, as required by the electrolytic refinery, may result in several operational difficulties. Furthermore, by recycling the flue dust and slag produced in the smelting-fire refining cycle, the arsenic content in the feed to smelting increases and so does in the resulting anode copper. The Teniente Converter, as a smelting unity, has probed suitable for production of high matte grade near white metal composition but regarding distribution behaviour of impurities there is lack of reliable data, specially when processing concentrates over 1% in arsenic content. In the new scenario, i.e. low grade copper high arsenic content concentrates, to fully asses the merits of this technology the effect of matte grade, secondary materials recycling and arsenic in feed upon the distribution coefficient of arsenic between slag and matte, mainly, must be evaluated both from a theoretical approach and by use of industrial data. Based on available data correlations of distribution coefficient, matte grade and matte/slag ratios with arsenic in feed and copper content in slag are worked out. Based on these results suggestions as to matte grades facilitating to deal more efficiently with the handling of smelting byproducts are proposed.

Jan 1, 2006

By M. Brian Maple

A rich variety of phenomena are produced by superconducting-magnetic interactions in rare earth and actinide compounds. These phenomena, and the materials in. which they have been observed, are described in this talk, with an emphasis on the new high superconducting transition temperature (Tc) copper oxides. The Materials The-materials in which these phenomena occur can&apos; be divided into two classes. In the first group, there are two distinct interpenetrating systems of electrons, a set of localized 4f or 5f electrons and a set of itinerant electrons. The localized f electrons carry magnetic moments and interact with the spins and momenta of the the itinerant electrons, which are involved in the superconductivity, via exchange and electromagnetic interactions; respectively. This category includes materials containing rare earth (R) and actinide elements with partially-filled f electron shells which have been inroduced as substitutional impurities [e.g., La1-xCexA12, Th1-xUx] or form a sublattice in compounds [e.g., RRh4B4, RMo6S8, RMo6Se8, the high Tc. superconductors RBa2Cu3O7-d(d - 0.05)]. Materials of the second type are characterized by a single band of electrons that is responsible for both superconductivity and magnetic order. This group includes heavy electron rare earth and actinide compounds [e.g., CeCu2Si2, UBe13, UPt3, URu2Si2], and the high Tc copper oxide superconductors such as the hole-doped systems Lag- MxCuO4 (M = Ca, Sr, Ba, Na) and RBa2Cu3O7-d(0 =d= 1) and the electron-dope system Ln2-xMxCuO4-y (Ln = Pr, Nd, Sm, Eu; M = Ce, Th; x = 0.15; y - 0.02).

Jan 1, 1992

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By Shoji Taniguchi, Lifeng Zhang

"In this paper, firstly the 3D single-phase turbulent steady fluid flow in a vessel with four baffles stirred by a single impeller is mathematically simulated. Turbulence is modeled by using the standard k - e model. Sliding-grid method is used to model the impeller. The flow domain is divided into two cylindrical, the inner one rotates at the same speed as the impeller, and the outer one is fixed with the baffles. Results indicate that the high-speed zone is near the paddles, and larger stirring speed generates larger fluid flow velocity. The calculated stirring intensity data are used to analyze the experimental results. Secondly the effects, such as filter pore size, gas flow rate and NaCl concentration, on bubble size are studied by experiment. For the particle removal rate by bubble flotation in this vessel, first order kinetics is adopted. The effects of initial number of the particles, gas flow rate, particle and bubble size, stirring speed and surface condition, on the removal rate constant are discussed, and an empirical equation is derived by experimental data. At last, a simple model is developed to study the particle attachment probability on bubble surface under turbulent flow conditions. IntroductionIt is well known that inclusions have a bad effect on steel quality. Trying to remove inclusions from liquid steel as many as possible is one of the main objects for the metallurgical workers. Lots of ways are developed to remove inclusions from liquid steel. Gas injection is an effective one. This technique is used to achieve homogeneity in the temperature and metal composition and to assist in the removal of second phase and dissolved impurities from molten steel. Gas injection is commonly applied to the secondary metallurgy processes and continuous casting, for example the ladle argon gas treatment, RH vacuum degassing, and the gas injection in the Submerged Entry Nozzles (SEN) of continuous casting mold, etc. The development of these processes focuses on achieving two conditions: fine bubbles and good mixing. Fine bubbles provide a large gas/liquid interfacial area and a high attachment probability to inclusions, and good mixing enhances the efficiency of impurity transfer."

Jan 1, 2000

By M. O. Lai

"Metal matrix composite (MMC) with composition of Al-4.Swt.%Cu reinforced by IOwt.%TiB2 or ISwt.%SiC particulate has been successfully fabricated using powder metallurgy technique. Disk, compression and beam specimens were prepared with (a) layered structure containing ductile Al-4.Swt.%Cu with brittle Al-4.Swt.%Cu/TiB2 or Al-4.Swt.%Cu/SiC layers, and (b) homogenous constituent with composition of Al-4.Swt.%Cu/lOwt.%TiB2' The specimens for the fracture toughness measurement were built through three ductile-brittle-ductile alternating layers. For the beam specimens, the layers were built through brittle-ductile-brittle sequence. The brittle layer consisted of Al-4.S%Cu with fixed amount of reinforcement. Fracture toughness testing revealed an increase for layered composites although the total amount of the reinforcement was the same for all disk specimens. The increase in fracture toughness is due to the existence of ductile layers which manifests a strong influence on delaying the occurrence of fracture. It acts as a barrier to resist the propagation of crack and hence increases the fracture toughness of the layered MMC specimens, Delamination in the beam specimens was observed to be due to shear stresses. Fracture surfaces of both disk, compress and beam specimens were characterized using the SEM. IntroductionMechanical and thermal properties can be achieved by the incorporation of refractory secondary phases to constrain the plastic flow of the matrix in a metal matrix composite (MMC). The size of the reinforcement particulate incorporated must be in the range larger than the dislocation cell size and strongly bonded to the matrix (I). Particulate reinforced metal matrix composites hence provide high modulus, improved wear resistance and strength (2-4). Because of the incorporation of refractory phases which are generally brittle, the major limitation in the mechanical properties of MMCs is their limited ductility in comparison to their base metals. Cracks normally initiate from the reinforcement and voids (4, 5). Due to the lack of ductility, cracks propagate rapidly with increase in load. As a result, the interactions between reinforcement particles and propagating cracks have recently been of great research interest (6). In addition, volume fraction of reinforcement and aging condition of the matrix significantly affect the mechanical behaviour of MMCs. In the case of AI-3.5%Cu reinforced with varying volume fractions of SiC particulate, it has been found that the probability of particle fracture increased with increasing volume fraction of reinforcement (7)."

Jan 1, 1996

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

The effect of microwave irradiation on grinding property of coal was studied by using Hardgrove grindability index tester. Superior grindability of coal was obtained to varying extent after microwave irradiation treatment. The variation in microstructure of pulverized coal during microwave irradiation was observed by utilizing scanning electronic microscope (SEM). The results indicated that the different microwave absorbance of minerals and carbon matrix led to cracks on their interface, by which coal particles were further pulverized and therefore the granularity of coal powder was reduced. Due to the different formation process of various coals, bituminite and anthracite are very different in physical and chemical properties. According to the content of coal pulverization, it can found that microwave irradiation has a stronger pulverizing effect on bituminite in comparison to anthracite.

Jan 1, 2016

By Tao Jiang

Germanium is widely used in many fields, and the production of germanium is very important. The effects of initial sulfuric acid concentration, liquid to solid ratio and other parameters on the leaching rate of germanium and zinc from germanium-bearing zinc oxide has been studied. The occurrence and form of germanium and other elements in the leach feed and the leach residue were studied by EPMA, XRD and chemical analyses. The experiments showed that the leaching rate of germanium and zinc was 91% and 88%, respectively under optimal conditions. Wurtzite was the main limiting factor for the leaching rate of zinc while the leaching rate of germanium was limited by insoluble germanium compounds. Furthermore, it was found that some germanium was bound up in galena in the leach residue. These results may be helpful for further improving the leaching rate of germanium in germanium-bearing zinc oxide.

By P. M. Tyroler

At INCO&apos;s Copper Cliff Nickel Refinery, nickel is extracted by using the INCO Pressure Carbonyl (IPC) process. The resulting IPC residue containing copper, nickel, cobalt, iron, sulphur, precious metals, selenium and tellurium is further processed at a hydrometallurgical plant. This plant treats approximately fifty metric tons per day of IPC residue. The components of the feed are separated in a number of steps and a precious metals concentrate, nickel-cobalt carbonate, a selenium-tellurium intermediate and copper cathodes are produced. An iron-arsenic waste stream is also produced and discarded to tailings. The hydrometallurgical processes include pres- sure leaching, cementation, precipitation, thickening, filtration and electrowinning. This paper describes in detail the individual steps of the flowsheet.

Jan 1, 1988

By Ann M. Hagni

Reflected Light Microscopy (RLM) And Scanning Electron Microscopic-Energy Dispersive Spectroscopic Analysis (SEM-EDS) Study Of Electric Arc Furnace (EAF) Dusts Have Shown That Their Mineralogy Is Complex And Varied. The Particles Are Largely Spherical, And Can Be Seen In RLM Sections To Be Composed Of Franklinite, And Zincite, But They Show Significant Solid Solution With Each Other And May Contain Small Amounts Of Chromium. These Crystalline Phases Occur As Crystals And Skeletal Growths Within Ca-Fe-Si Glass. Because Chlorine Is A Deleterious Constituent In Recovered Zinc Products From EAF Dusts, Special Attention Has Been Given To Chlorine-Bearing Phases, And They Include Hydrophylite (Cacl2), Lime (Cao), And Organic Phases. Pyrohydrolysis-Treated EAF Dusts With Silica (Si02), Tungstite (W03), Alumina (A1203), And Bunsenite (Nio) Additives Contain Franklinite, Scheelite (Cawo4), Willemite (Zn2SiO4), And Hematite (Fe2O3)

Jan 1, 1992

By C. M. Chen

Friction stir welding (FSW) is a pure solid-state joining process, which has been widely used in joining aluminum alloys with improved properties. This paper describes a three-dimensional simulation of FSW process, running the ANSYS package of finite element analysis to study the evolutional stress in the butt-welding of aluminum alloy 6061-T6. The model incorporates the mechanical effect of the tool and thermomechanical process of the welded material. The heat source involves the friction between the material and the probe and the shoulder. Thermal history and the evolution of longitudinal, lateral, and vertical stress in the friction stirred weld are simulated. The relation between the calculated residual stresses of the weld and the process parameters such as tool traverse speed is presented. Keywords: Fiction Stir Welding, Finite Element Analysis, Thermomechanical Process, Evolutional Stress, Residual Stress.

Jan 1, 2003

By Andrzej Warczok

Liquid slags produced in smelting of copper concentrates contain copper in a dissolved form as well as mechanically entrained inclusions of copper matte. Coalescence and sedimentation of inclusions during slag cleaning plays a key role in copper recovery. Liquid matte inclusion in a molten slag presents a system of metallic conductor in an ionic solution. Constant electric field induces migration of the matte droplet along the current lines. Additional phenomena occur in a system under crossed electric and magnetic fields. Electromagnetic buoyancy force acting on the inclusion affects its settling rate. Electromagnetic buoyancy force of insulating and metal spheres has been measured in a liquid synthetic slag. It was found that depolarisation of the metal sphere, related to the electrode reactions occurring in the surface, plays an important role in the determination of the direction and magnitude of the electromagnetic force. On the basis of the existing theories and results of measurements a mathematical model describing the behaviour of metallic inclusions in the liquid slag under the influence of crossed electric and magnetic fields was developed. Simulation of behaviour of copper matte inclusions under crossed fields showed trajectory of motion in a liquid slag as a function of the slag properties and the inclusion size.

Jan 1, 2003

By Dongping Duan, Hongliang Han, Li Zhong, Siming Chen, E Zhou

In this study, physical, chemical and microscopic characteristics of Celestine were investigated firstly. Based on which, the thermodynamic analysis of Celestine reduction was discussed. And the experiments of Celestine carbon-containing pellets used in rotary hearth furnace process were studied. The results showed that it is feasible to deal with Celestine by rotary hearth furnace direct reduction process. When the temperature is 1200°C, C/O ratio is 0.8 and holding times is 20min, the conversion rate of SrSO4 in Celestine is above 95%, the utilization rate of Celestine is nearly 100%. This study can provide theoretical and technical basis on economical and rational use of Celestine.

Jan 1, 2016

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet&apos;s manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet&apos;s specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996