Search Documents

By Kunio Nakahara, Kashiwagim Junichi, Takao Hayashi

"There are many problems for electronic devices and parts which were caused electrostatic damage by static electricity. It is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating. Mitsui Mining & Smelting Co., Ltd. developed metal oxide type electroconductive pigment PASSTRAN (trade mark) Type-IV which is barium sulfate coated with SnOz(Sb) thin electroconductive layer. This paper shows about pigment characteristics and film condition of antistatic transparency paint which contained PASS TRAN.L.IntroductionRecently rapid development of electronics technology diffused electronic devices and products to Office, Factory, Laboratory and our life. But the other side, there are many problems for electronics parts which were caused electrostatic damage under static electricity. Demand of antistatic materials were become lager by this situation.There is close relationship between surface resistivity of material and static electricity. If the surface resistivity of object is enough low (under 109 Q /Sq), static electricity is dissipated quickly. So it is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating.1) There are many type of electroconductive materials, for example, carbon black, metal powder, electroconductive polymer and so on. Especially, carbon black is used for general purpose by reason of its low cost, but it has big problem of black color. It can not get any color without black, and it caused contamination of carbon.In recent years, metal oxide electroconductive pigment (ECP) was developed and used for special purpose which demands transparent coating or easy dispersion to make ECP paint or endurance under hard environment and so on. Mitsui Mining & Smelting Co., Ltd. developed electroconductive pigment PASSTRAN Type-IV which is BaS04 coated with electro-conductive Tin oxide layer."

Jan 1, 1998

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By S. P. Marsh, D. Banerjee

"Casting processes involve phenomena that occur on widely disparate length-scales. Simulation of macroscopic effects, such as heat transfer and convection, are generally addressed by solving the appropriate equations in discretized form on a finite-element mesh. Microscopic phenomena are described by micromodels that may be empirical or analytical in form. Coupling of phenomena in these two regimes is a critical issue in predicting microstructure and defect formation resulting from macroscopic process conditions. A formalism has been developed for expressing micromodels in a consistent manner using stereological parameters to quantify the geometric characteristics of the developing microstructure. This approach provides a robust and physically consistent method for coupling local micromodels with the macroscopic fields. The macroscopic state variables at each node serve as global constraints on the micromodels that are applied to a local unit volume. An outline of an equiaxed solidification model based on this approach is presented, along with preliminary simulation results. Coupling of convection and enthalpy effects between the micro and macro regimes is also discussed. IntroductionThe primary goal of casting simulations is to improve the reliability of cast parts while minimizing cost and development time. Effective simulations can speed up the mold design process and reduce the likelihood of defective parts by refining a particular casting process on a computer, reducing the dependence on cost- and time-intensive prototype castings. The challenge in developing effective simulations stems from the need to address physical processes that occur over a wide range of length-scales, from microscopic (atomic) and mesoscopic (microstructural) scales to macroscopic distances comparable to the size of the casting itself. Overviews of the various thermophysical phenomena and computational factors that are important in solidification modeling are provided in the literature by Rappaz [1] and Tseng et al. [2].Macroscopically, the solidification process is largely governed by the rate of heat flow from the alloy through the mold wall. Another important effect that occurs on the scale of the casting size is convective flow of the melt, which is driven by density-variations in the melt. Macroscopic calculations employ finite-element or finite-difference methods to solve the sets of equations that govern these effects, and the spatial resolution is determined by the grid spacings used for the calculations. Typical spatial resolutions are on the order of 10-2 to 10-3"" meters. This represents a compromise between the resolution required to simulate the continuum transport processes accurately, and the computational time required to model the entire solidification and cooling process."

Jan 1, 1994

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By Daniel Kim, Michael Free, Justin McAllister, Urian Marshall, Shijie Wang

"Cathode impurity levels of electrorefined copper were evaluated based on 1/10* scale laboratory electrorefining tests. Cathodes were evaluated near the top, mid-section, and bottom sections of cathodes on both the set and mold sides and strip and scrap cycles. Slime weights were measured, and slime and electrolyte samples were also evaluated for impurities. Results from these tests have been compiled and compared to evaluate the effects of changes in operating conditions and electrode location on cathode impurities.IntroductionMany types of impurities are commonly found in commercial copper electrorefining anodes. The smelter operations that produce the anodes process concentrates that contain a wide variety of impurities that vary based on the mineralogy of the ore. Most anode impurities are removed during electrorefining. However, a portion of the anode impurities is incorporated into the copper cathode product. The mechanisms by which impurities are transported from the anode to the cathode are not well understood. Some impurities can be transported as anode slime particles to the cathode where they are incorporated into the cathode. Other impurities can be transported as dissolved species that are electrochemically reduced with the copper to become part of the cathode. Although research has been performed on anode slimes and impurities [1-4], there is a need for additional information regarding the relationships associated with electrorefining cycles, electrode faces, local electrode positions, anode impurities and specific cathode impurities. The objective of this study was to evaluate lead, arsenic, and antimony cathode impurity trends associated with electrorefining cycles, electrode faces, local electrode positions, and anode impurities. A variety of techniques including electrolyte filtering, anode heat treatment, high electrolyte arsenic concentration, high arsenic and/or lead in anodes, flocculation of slime particles, and appropriate current density control were used to vary cathode impurity levels. Each test was performed only once for a strip cycle and once for a scrap cycle. Consequently, the results for the individual conditions are preliminary and are not the focus of this study. However, the collective set of data with varying impurity modifying techniques provides a broad range of impurity levels, and the associated trends with respect to lead, arsenic, and antimony are discussed in this paper. Approximately 180 analyses of copper cathode were used to track the antimony, arsenic, and lead impurities. Eighteen anode slime samples were also analyzed for antimony, arsenic, and lead."

Jan 1, 2012

By William A. Apel

Several different strains of bacteria have been shown capable of reducing hexavalent chromium, Cr(VI), to Cr(III), a less toxic, .. more readily recoverable form of Cr. This paper examined the Cr(VI) reduction efficacies of 3 different Cr(VI) reducing bacteria: Pseudomonas f1uorescens LB300., Pseudomonas aeruginosa PAOI, and Pseudomonas aeruginosa PAOI (pCROI) It was demonstrated that all three bacterial stratns reduced Cr(VI) primarily during their exponential growth phases while using glucose as their carbon and energy source. Significant differences in the three organisms' Cr(Vl) reduction capabilities depending on initial Cr(VI) concentrations were also demonstrated. P. aeruginosa PAOI showed superior Cr(VI) reducing capabilities over the. entire range of Cr(VI) concentrations tested while the Cr(VI) reduction capabilities of the other two strains were increasingly inhibited as Cr(VI) concentrations increased.

Jan 1, 1991

By Toshiaki Nakai, Kunihiko Takeda, Kimio Imaizumi, Hiroaki Shirasaka

"The new type of nano-porous silica particle was considered to be constructed by the spinodal decomposition-type process which was found to have narrower pores than those of conventional porous silica prepared from boron silicate or ""Shirasu"" balloon. Nano-porous silica particles were fabricated by the calcination of silica gel mixed with well-dispersed complex salts composed of phosphorous and molybdenum compounds. Both silica and inorganic salts were not perfectly dissolved in the suspension solution. After removing of the water, the silica-inorganic salts complex was volatized and successively calcinated at a temperature ranging from 650 °C to 800 °C. Then, the inorganic salts were removed by dissolving in hot water. Other inorganic salts such as potassium halides were also found to be effective as a pore-size controller.IntroductionControl of structure has an important role in the field of industry as well as in the separation and purification technology for metals and organic syntheses. Many studies on the control of material structures have been reported regarding porous materials with pores ranging from nanometer to micrometer scale. 1 ) One example is zeolite as a naturally yielded porous inorganic material. Various types of synthetic zeolites have been studied as ""molecular sieve"" materials with ordinary pore-size of less than one nanometer. In 1992, crystalline meso-porous material with a large surface area named MCM-41 was synthesized through the use of template synthesis. 2) In direct relation to our study, amorphous borate glass having 4 to 100 nm of fine pores known as Corning glass 3l or SiO2-Al2OrB2O 3-CaO porous glass having large pore dispersity ranging from 4 to 10,000 nm have been reported. 4 ) S) 6 ) Some examples of several reported studies are as follows: phase-separated porous glass consisting of B2OrAl2O3-ZrO2-RO-R2O complex oxide 7 ) glass with finer pore induced from hydrolysis of silane alkoxide, porous material attained by condensation polymerization through the use of sol-gel process 8), alumina meso-porous material 9 ) 10), silica-zirconia material 11), carbon porous material 12), etc.."

Jan 1, 2000

By R. Togashi, T. Aichi, T. Yamada

"A new automatic material- handling system for cathode transportation has been developed. The first system went into service in August 1994 and the remains will be operational subsequently.Because of the complex cell-layout and the number of cells in each row, the critical part of this work was achieving a planned cycle time. This cycle time is determined by the power costs.The central monitoring system for machine operation was started in June 1996, using original application software based on MICROSOFT EXCEL ® on WINDOWS 95® .As a result, only one person is now required to operate both a crane and a stripping machine for one row of about 50 cells.INTRODUCTIONMainly due to the strong yen and the relatively low price of metal, the zinc refineries in Japan are being forced to reduce production costs again and again.The trend of lijima's production costs is shown in Figure 1.[1] The ratio of labor costs becomes gradually higher. Therefore it is effective to reduce the labor costs in order to reduce the production costs. In Japan, electricity cost during day time is too high to produce zinc at a reasonable cost, that is why the actual production is far from the capacity of production at a cell house. That means a plant in Japan has the disadvantage of relatively low productivity for cell house operation.Saving labor costsSome automatic cranes have been applied to save labor costs for cell house operation in the world. In consideration of the mentioned low productivity, the installation of an Automatic Cathode Transfer (ACn system for transportation of cathodes was planned without changing the present cell house and stripping machines to lower the investment costs. The ACT system must keep up with the stripping machine which is able to strip deposit zinc from a cathode sheet at the rate of 6 seconds.The fifth ACT system of seven was installed in August 1996 and the last one will be operational subsequently."

Jan 1, 1997

By Sang-Su Lee

This paper shows the application of the porous plug system in the Mitsubishi continuous copper smelting and converting process. This system has already been adopted and utilized in the steel industry to enhance productivity. Recently, some copper smelters have adopted this system but the results have not been satisfactory. The porous plug system was installed at the anode furnace in December 2001 to reduce the oxidation time and decrease the oil consumption. A good effect was that the nitrogen stirring of the melt through porous plugs improved the melt heat transfer. As the result of the enhancing heat transfer the oil consumption and the build up inside the furnace were actually decreased. But until now the oxidation time has not been sufficiently reduced. In the future, further research and tests are needed in order to increase the productivity and save costs.

Jan 1, 2003

By Chang Wei, Zhigan Deng, Jiqiang Liao, Minting Li, Hongsheng Xu, Yan Song, Cunxiong Li, Xingbin Li

"Abstract: Direct ?otation of oxidized zinc-lead ore is characterized by recovery of zinc and lead only around 55% and 50%, respectively. Mineralogical analysis shows that the sample used in the present study is a carbonate hosted zinc-lead ore, with a zinc and lead carbonate content that accounts for 80.14% and 75.63% of the total minerals, respectively. The carbonate hosted zinc-lead ore was hydrothermally sulfidized with elemental sufur and the experimental data indicated that under the conditions employed up to 75% zinc and 82% lead sulfidation extent were achieved. As a result of pre-sulfidation followed by flotation, the recoveries of zinc and lead into flotation concentrate were over 90%. A flotation concentrate was obtained with 52% Zn and 37% Pb from the materials which was treated by sulfidation.IntroductionSulfide ores are the primary source of zinc and lead, and they are becoming depleted; thus, metallurgical investigators are interested in using abundant oxidized zinc-lead ore reserves. The high-grade zinc-lead oxidized ore, which normally has a zinc content higher than 15%, can be disposed of by acid leaching and electrolysis. However, the low-grade ore, which has a zinc content lower than 10%, is difficult to smelt with pyrometallurgy and hydrometallurgy, and the processes are very complicated and expensive in terms of production flow and energy consumption. Therefore, making the low-grade oxidized zinc-lead ore more beneficial has become more important in recent years. Flotation is the most common process, and the primary method of recovering zinc and lead from sulfide or oxide minerals. It is well known that there is a difference between sulfurized and oxidized minerals regarding their separation by flotation. Flotation of zinc and lead oxidized minerals is extremely complex because of the similarities in the physicochemical and surface chemistry of the constituent minerals. There are no known direct-acting collectors capable of producing single metal concentrates [1-3]."

Jan 1, 2012

By S. I. Sobol

The results of the study of the mechanism of a cathode process of cobalt electrolysis to explain disagreements in a form of kinetic equations of autoclave reduction of nickel and cobalt have been used.

Jan 1, 1993

By J. M. Floyd

Technology in use commercially and available for commercialisation for injection processing of base and precious metals in bath reactors is surveyed and compared. Differences between bath smelting and suspension smelting systems are highlighted in relation to important smelting criteria. The factors affecting the results achievable with various tuyere and lance injection bath smelting systems are discussed in relation to the various smelting, converting and refining operations involved in copper, nickel and precious metal processing steps. Process chemistry, process dynamics and heat and mass transfer rates are discussed for the different systems.

Jan 1, 1993

By Huanyu Zhang, Quanqiang Ma, Huiqing Tang

Improvement of the coke quality for blast furnace (BF) iron making by hydrothermal oxidation treatment on coke quality was investigated. Results show that, under subcritical condition, sulfur removal rate is 15% and the weight loss is 3%; under supercritical condition, both sulfur removal rate and mass loss rate increase with the increase of H2O2 concentration. In the experimental conditions, sulfur removal rate and mass loss rates were 45% and 17%, respectively. Hydrothermal oxidation treatment could reduce the CO2 reactivity of the coke and the treatment under supercritical condition is more effective. Hydrothermal oxidation treatment could improve the graphitization of the coke and smoothness of pore boundary in the coke and the treatment under supercritical condition is more effective.

Jan 1, 2016

By Tracey Brommer, Britt Elin Gihleengen, Elsa Olivetti, Randolph Kirchain

"Increased demand resulting from the economic and environmental advantages of recycling secondary materials has constrained secondary material supply. As a result of constrained supply, the conventional strategy to maximize recycled content in an individual aluminum alloy must be expanded to maximizing total recycled content in a given production period. This work compares the performance over a two week period of an actual remelter for two strategies; a sequential charge-by-charge optimization framework and an integrated approach that explicitly incorporates the production schedule. Optimizing across the entire two week production is found to increase recycled content and minimize primary and alloying material additions. It is expected that as the scrap material market continues to be constrained by high demand, longer term batch planning strategies that can optimize material allocation will deliver improved performance.IntroductionIntensifying economic and environmental pressure to incorporate secondary aluminum into products is pushing remelters to explore additional strategies and tools to increase recycled content. Aluminum remelters are exploring alternative sources of secondary materials because of constrained secondary material supply and relatively high primary and secondary material cost [1]. Computational models, such as blending models are a tool that could help industrial remelters mitigate supply and cost challenges and thereby increase recycled content. In particular, computational tools can help manage the incorporation of new raw materials of variable quality. Blending models find many industrial applications and have been explored for over sixty years originating with the classic nut-mix problem dating back to 1950’s [2]. Blending models optimize the raw material input to make a desired product subject to a series of constraints such as product specifications and material availability. Deterministic and linear blending model formulations are presently implemented in some industrial aluminum remelters [3]. The primary reluctance of aluminum remelters against computational model implementation is the incapability of their blending models to reflect the intricacy of industrial remelting conditions [4]. For example, to reduce calculation time, industrial aluminum blending models usually optimize a batch plan for a single alloy and are not formulated to optimize several products simultaneously. Since such a model does not include knowledge of subsequent charges in the optimized batch plan, the resulting batch plans tend to deplete the “cleanest” secondary materials leaving the more uncertain and compositionally challenging materials for later charges. As a result, a remelter may override the calculated batch plan or leave certain scrap materials out of the material input to conserve these materials for alternative products scheduled for later production. This work explores an alternative aluminum charge planning tool that can optimize across an extended production schedule and compares it to a heuristic sequential optimization strategy reflecting an industrial remelter."

Jan 1, 2012

By J. B. Cocanour

Pioneering work at the U.S. Bureau of Mines (USBM) has produced a personal computer (PC)-based, software-driven video photometric color sensor for real time process control of metallurgical streams. The video photometer is an inexpensive optical sensor which operates in the visual area of the electromagnetic spectrum and collects color information through plastic optical fiber. The red, green, and blue (R/G/B) voltage components of the color video signal are digitized and characterized through software and then presented as the control variable for software-based proportional-integral-differential (PID) control. This sensor has been successfully employed in the control of a laboratory copper electrolytic circuit. With this sensor, copper solutions were analyzed on-line without the need for sample removal, dilution, mixing or reagent addition, thereby allowing for the real time control of the circuit.

Jan 1, 1994

By Jiang Fan, Wang Haigang

"The three-dimensional complex multiphase turbulent flow in U-beam separators was simulated using the Reynolds stress equation models (RSM). To account for the effect of the stochastic characteristic of the instantaneous gas velocity on the particles, the improved Lagrangian stochastic model based on the Reynolds stress model for gas phase was adopted, which attributed to the successful prediction of the turbulence anisotropy and particle crossing trajectories effects. The interaction between the particles was also considered using the HardSphere model. To treat the particle-wall collision, the influence of the roughness of the wall on the motion of the solid particles was taken into consideration by imposing random collision angles. The result from this study not only shows the dynamic characteristics of the multiphase flow- in the separators, but also gives the relationship among the efficiency, structure and pressure losses of the separator.IntroductionCirculating fluidized bed (CFB) combustion is one of the most promising clean coal techniques. A main feature of CFB boilers is the un-delayed recycle of solid, coal and sorbant particulate, in an external loop. Separator, which is required to separate the solid particle from the flue-gas leaving the reactor of CFB, plays an importance role in the external solids recycle loop. It affects the combustion of CFB system greatly. Presently cyclone is the most commonly used as separators for CFB system and other chemical industrial processes. It provides high level of separation for CFB system for fine particles. However it suffers from some inherent disadvantages. It's volume and size is huge. Moreover, it is difficult to design and install when the CFB workload rises. The application of U-beam separators instead of hot cyclone separators in CFB boilers has many advantages. Publications indicate proposals or successful use of Ubeam separators in Swedenr11, USA 21, Russia r3land China [4]• But it is not possible to find results in the literature of detailed investigations of this new. type of separators or recommendations on the choice and calculation of an optimal design. For this reason, numerical simulation for the three-dimensional gas-particle two-phase flows with several rows of vertical U-beam elements, local in the chess order and blocking a way of outgoing from a CFB boilers dusted gases was carried out in this study."

Jan 1, 2004

By Jefferson Caponero

The tire is an expressive component of Municipal Solid Waste, manly when its occupied volume is considered. Its treatment by pyrolysis stands for a list of advantages, such as: landfill releasing and a production of a high quality fuel. The exploitation of new natural resources is becoming more difficult each day, basically due to the environmental damages caused by this type of activity. This work presents a study on the thermal behaviour of Brazilian tires using thermogravimetric analysis and differential thermal analysis, in order to optimise the pyrolysis process of tires. Samples of I to 2 mm were investigated at atmospheres of nitrogen, argon, oxygen and mixtures of these gases at temperatures up to 1273K, under heating rates between 1 to 50 Klmin . The results showed that the behaviour of each sample is related to both the atmosphere composition and the heating rate.

Jan 1, 2001

By A. De, J. S. Zuback, T. Mukherjee, T. DebRoy

For successful commercial applications of additive manufacturing, metallic parts need to be defect free, structurally sound and reliable. However, additively manufactured metallic parts are susceptible to distortion, lack of fusion defects and compositional changes. Methods to measure susceptibilities of various alloys to these defects are needed but not currently available. Here we show that the necessary theories can be developed based on a well-tested numerical heat transfer and fluid flow model and decades of research in the field of welding. The proposed theories are validated with experimental results reported in the literature.

Jan 1, 2016

By Natasa Mitevska

The statistical analysis of the slag composition influence on copper losses to discard slag in the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Yugoslavia) is presented in this paper. The model for the slag basicity calculation is determined, and connected to the copper distribution coefficients between the matte and slag phase. The influence of all components on the slag structure is also illustrated.

Jan 1, 2003

By Shigehisa Endoh, Hitoshi Ohya, Atsushi Inaba, Shigeki Koyanaka

"Recycling should be promoted to keep the global environment. However, it is difficult to detennine the quantitative impact. A life cycle assessment is one of the most reliable methods to estimate the global environment impact.Exergy is useful like entropy when considering the sustainable development. All of our activities have been obtained exergy resources and/or energy itself and throw away waste and/or waste heat. We are trying to use exergy to estimate the quantity of energy and matter for resource accounting. For recycling plastic, plastic has two aspects; material and energy source.The environmental assessment of plastic recycling suggests that the exergy reduction of the entire system is estimated by the yield of matter and the process efficiency. The material recycling is better than the thennal recycling when the process efficiency is high. However, the thennal recycling is much better for the low efficiency. The transition point is able to be decided by the efficiency of the manufacturing and the electric power generation.IntroductionRecently, many of the global environmental problems have become conspicuous like global wanning, ozone layer depletion and acid rain. Some of the methods like life cycle assessment for solving these problems have been presented. Anxiety concerning the proble1ns of energy and resources has led to a rapid increase in the interest in describing and understanding the conversion processes of energy and other resources in today's society. All human activity is supported by obtaining power and products of high exergy from the environment and throwing away the waste material and the waste heat of low exergy back the environment. However, the total exergy in the whole system becomes absolutely smaller than before.The rate of obtaining high exergy products and energy itself by human activity and the speed, by which waste and waste heat having low exergy are thrown away are too fast to attribute to environmental problems [1-3].A material's use by recycling was often common in a circulating society mainly. A significant amount of energy is consumed during circulation. An environmental impact assessment method for the process or the system has not been devised when both of them are taken into consideration. Even if the life cycle assessment evaluation, which has been correctly used up to now, is applied, it is not sufficient for an overall evaluation concerning matter and energy.The real sustainable development is that the exergy reduction value by all human activities on the earth is kept within the range of the exergy reduction in order to consider the earth as closed stationary system. It is important to evaluate the process or the system by using the exergy, and design them so that the exergy loss may decrease as much as possible. We have to consider what process improvement is the most effective."

Jan 1, 2000